Synchronous dc direct drive system Patent
Synchronous dc direct-drive system comprising multiple-loop hybrid control system controlling load directly connected to actuator
Veillette, L. J.↗
SEARCH · Engineering Papers
Results for “controllable loads”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Design, fabrication, and testing of a full-length external-fuel thermionic converter
Double ended full length external fuel thermionic converter, describing component fabrication, assembly sequence, joining methods, vacuum test procedures and converter load control
Giorgio, F.↗
Improved parasitic speed controllers for space power systems
Parasitic speed controller for alternator rotational speed and frequency regulation in dynamic space power systems, investigating phase controlled loading improvement
Ingle, B. D.↗
Analytical design of a parasitic-loading digital speed controller for a 400-hertz turbine driven alternator
A design for a solid-state parasitic speed controller using digital logic was analyzed. Parasitic speed controllers are used in space power electrical generating systems to control the speed of turbine-driven alternators within specified limits. The analysis included the performance characteristics of the speed controller and the generation of timing functions. The speed controller using digital logic applies step loads to the alternator. The step loads conduct for a full half wave starting at either zero or 180 electrical degrees.
Ingle, B. D.↗
Separation of the strain components for use in strainrange partitioning
Two methods are presented for separating the inelastic strain components of a complex hysteresis loop so that strainrange partitioning formulas can be applied to accurately determine cyclic life at elevated temperatures. These methods are required only if lower bounds established by strainrange partitioning concepts have been deemed inadequate in the establishment of expected lifetime. In one method, rapid loading and unloading is applied in the tensile and compressive half to isolate the plastic strain. In the second method, the creep is measured at a discrete number of points along the hysteresis loop by combining load-control tests into the general pattern of strain cycling under arbitrary temperature. Both methods are shown to give good results.
Manson, S. S.↗
Power processing methodology
Discussion of the interim results of a program to investigate the feasibility of formulating a methodology for the modeling and analysis of aerospace electrical power processing systems. The object of the total program is to develop a flexible engineering tool which will allow the power processor designer to effectively and rapidly assess and analyze the tradeoffs available by providing, in one comprehensive program, a mathematical model, an analysis of expected performance, simulation, and a comparative evaluation with alternative designs. This requires an understanding of electrical power source characteristics and the effects of load control, protection, and total system interaction.
Fegley, K. A.↗
Technology and methodology of separating two similar size aerospace vehicles within the atmosphere
During the past 10 years, the parallel separation, within the atmosphere, of two similar size aerospace vehicles has been investigated in technical areas such as static and dynamic stability, rocket exhaust plume interference, aerodynamic control, loads, and dynamic simulation. Advanced experimental and analysis techniques have been developed to analyze this problem. Results are presented which summarize some of this work. The effects of various parameters on the separation maneuver are illustrated using results from early and current space shuttle configurations. The technology and methodology that have been developed have helped verify the feasibility of separating similar size aerospace vehicles.
Decker, J. P.↗
Separation of the strain components for use in Strainrange Partitioning
Two methods are presented for separating the inelastic strain components of a complex hysteresis loop so that Strainrange Partitioning formulas can be applied to accurately determine cyclic life at elevated temperatures. These methods are required only if lower bounds established by Strainrange Partitioning concepts have been deemed inadequate in the establishment of expected lifetime. In one method rapid loading and unloading is applied in the tensile and compressive half to isolate the plastic strain. In the second method the 'creep' is measured at a discrete number of points along the hysteresis loop by combining load-control tests into the general pattern of strain cycling under arbitrary temperature. Both methods are shown to give good results.
Manson, S. S.↗
A visual motion simulator for general aviation compensated within the nonlinear adaptive washout for actuator lag
A description is presented of the general aviation aircraft simulator recently acquired by the Langley Research Center, summarizing the complement of instruments, radio/navigation equipment, control loading, and other features. Emphasis is placed mainly on the two-degree-of-freedom motion drives developed for this simulator and the presentation of the dynamic response of the motion system (without washout) in terms of amplitude ratio and phase lag as a function of frequency. The nonlinear adaptive washout based on continuous steepest descent optimization presents cues in pitch rate, surge, roll rate, and sway, and allows for actuator lag compensation.
Ashworth, B. R.↗
Definition study for photovoltaic residential prototype system
A site evaluation was performed to assess the relative merits of different regions of the country in terms of the suitability for experimental photovoltaic powered residences. Eight sites were selected based on evaluation criteria which included population, photovoltaic systems performance and the cost of electrical energy. A parametric sensitivity analysis was performed for four selected site locations. Analytical models were developed for four different power system implementation approaches. Using the model which represents a direct (or float) charge system implementation the performance sensitivity to the following parameter variations is reported: (1) solar roof slope angle; (2) ratio of the number of series cells in the solar array to the number of series cells in the lead-acid battery; and (3) battery size. For a Cleveland site location, a system with no on site energy storage and with a maximum power tracking inverter which feeds back excess power to the utility was shown to have 19 percent greater net system output than the second place system. The experiment test plan is described. The load control and data acquisition system and the data display panel for the residence are discussed.
Shepard, N. F.↗
Heat pipe nuclear reactor for space power
A heat-pipe-cooled nuclear reactor has been designed to provide 3.2 MWth to an out-of-core thermionic conversion system. The reactor is a fast reactor designed to operate at a nominal heat-pipe temperature of 1675 K. Each reactor fuel element consists of a hexagonal molybdenum block which is bonded along its axis to one end of a molybdenum/lithium-vapor heat pipe. The block is perforated with an array of longitudinal holes which are loaded with UO2 pellets. The heat pipe transfers heat directly to a string of six thermionic converters which are bonded along the other end of the heat pipe. An assembly of 90 such fuel elements forms a hexagonal core. The core is surrounded by a thermal radiation shield, a thin thermal neutron absorber, and a BeO reflector containing boron-loaded control drums.
Koening, D. R.↗
Evaluation of the cyclic behavior of aircraft turbine disk alloys
Five aircraft turbine disk alloys representing various strength and processing histories were evaluated at 650 C to determine if recent strength advances in powder metallurgy have resulted in corresponding increases in low cycle fatigue (LCF) capability. Controlled strain LCF tests and controlled load crack propagation tests were performed. Results were used for direct material comparisons and in the analysis of an advanced aircraft turbine disk, having a fixed design and operating cycle. Crack initiation lives were found to increase with increasing tensile yield strength, while resistance to fatigue crack propagation generally decreased with increasing strength.
Cowles, B. A.↗
Evaluation of the cyclic behavior of aircraft turbine disk alloys, part 2
Several nickel-base aircraft turbine disk superalloys were evaluated at 650 C for resistance to fatigue crack initiation and propagation under cyclic and cyclic/dwell conditions. Controlled strain low cycle fatigue (LCF) and controlled load crack propagation tests were performed and results utilized to provide a direct comparison among the alloys. Tests were performed on selected alloys to evaluate the effects of hold times, mean stresses, stress-dwell cycle types, inert environment, and contractor test methods. At the lower total strain ranges of interest, the alloys exhibited generally increasing initiation life with increasing tensile strength for both cyclic (0.33 Hz) and cyclic/dwell (900-sec hold per cycle) conditions. Rank order of the alloys by LCF initiation life changed substantially at higher strain ranges, approaching the rank order expected from monotonic tensile ductilities. The effect of the 900 sec (15 min) hold time fatigue life varied significantly from alloy to alloy. Generally, the higher-strength, finer-grained alloys exhibited more significant reductions in fatigue life due to the dwell. The effects of mean strain were found to be negligible and the effects of mean stress were pronounced. At high strain ranges the mean stress was near zero and did not contribute to reduction in life. At low strain ranges, however, mean stresses were large and significant reductions in LCF lives occurred.
Cowles, B. A.↗
LSS/propulsion interactions studies
Interactions between the LSS and the propulsion system are large, significant, interrelated, and complex. Issues and problems in interfacing include the effects on the structure from static, dynamic, and launch loads, control, thrust distribution, throttling, and the environment. Control interaction, the disposal of debris/obsolete spacecraft, and the constraints of launch to low Earth orbit must also be considered.
Spurlock, O. F.↗
Cycle life test of secondary spacecraft cells
The results of the life cycling program on rechargeable calls are reported. Information on required data, the use of which the data will be put, application details, including orbital description, charge control methods, load rquirements, etc., are given. Cycle tests were performed on 660 sealed, nickel cadmium cells. The cells consisted of seven sample classifications ranging form 3.0 to 20 amp. hours. Nickel cadmium, silver cadmium, and silver zinc sealed cells, excluding synchronous orbit and accelerated test packs were added. The capacities of the nickel cadmium cells, the silver cadmium and the silver zinc cells differed in range of amp hrs. The cells were cylced under different load, charge control, and temperature conditions. All cell packs are recharged by use of a pack voltage limit. All charging is constant current until the voltage limit is reached.
Harkness, J. D.↗
Generic multi-body formulation of heavy lift airship equations of motion
This paper describes the formulation of a comprehensive set of equations which describe the dynamic behavior of a generic heavy lift airship (HLA). They are being used in a digital computer simulation to investigate the response dynamics and flying qualities of HLAs operating with various payloads in a variety of operational environments. A key feature is the separate treatment of each component body making up the HLA. This allows the analyst to vary the configuration (e.g., number of lift-propulsion units, presence or absence of slung payload, etc.) without rewriting the equations. It further provides measures of key structural and control loads acting on the HLA and eases the task of modeling wind disturbances.
Ringland, R. F.↗
Flexible radiator system: Executive summary
A full scale prototype flexible radiator panel was designed, built and tested. The panel, has approximately 173 sq ft of radiating area and is designed to reject 1.33 kW of heat to a 0 F sink with a 100 F fluid inlet. The panel is constructed from a flexible Teflon/silver mesh fin surrounding 1/8 inch Teflon tubes. The prototype panel is stowed on a 10 inch diameter by 4 foot wide drum. (It rolls up to a diameter of 17 inches when fully stowed). Deployment of the soft tube prototype is via two four inch diameter Kevlar/Mylar inflation tubes with flat springs incorporated in each tube. Nitrogen is normally used for the deployment with approximately 1 psi required. The springs retract the panels when the inflation tubes are deflated. Another method of deployment available for the soft tube flexible is a motor driven deployable boom. This eliminates the need for expendables when the panel area is varied during the mission for heat load control. The soft tube panel is designed for a 90% probability of no punctured tube in a 30 day mission. The acceptable working fluids for this soft tube flexible are Coolanol 15, Coolanol 20 and Glycol/water (a eutectic mixture).
Oren, J. R.↗
Thermal-mechanical fatigue crack growth in Inconel X-750
Thermal-mechanical fatigue crack growth (TMFCG) was studied in a gamma-gamma' nickel base superalloy Inconel X-750 under controlled load amplitude in the temperature range from 300 to 650 C. In-phase (T sub max at sigma sub max), out-of-phase (T sub min at sigma sub max), and isothermal tests at 650 C were performed on single-edge notch bars under fully reversed cyclic conditions. A dc electrical potential method was used to measure crack length. The electrical potential response obtained for each cycle of a given wave form and R value yields information on crack closure and crack extension per cycle. The macroscopic crack growth rates are reported as a function of delta k and the relative magnitude of the TMFCG are discussed in the light of the potential drop information and of the fractographic observations.
Marchand, N.↗