SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Low subsonic stability and control of a 0.34-scale free flying model of a half cone reentry vehicle
This paper presents a verifiable model-reference adaptive control method based on an optimal control formulation for linear uncertain systems. A predictor model is formulated to enable a parameter estimation of the system parametric uncertainty. The adaptation is based on both the tracking error and predictor error. Using a singular perturbation argument, it can be shown that the closed-loop system tends to a linear time invariant model asymptotically under an assumption of fast adaptation. A stability margin analysis is given to estimate a lower bound of the time delay margin using a matrix measure method. Using this analytical method, the free design parameter n of the optimal control modification adaptive law can be determined to meet a specification of stability margin for verification purposes.
Engine Control Future aircraft turbine engines, both commercial and military, must be able to successfully accommodate expected increased levels of steady-state and dynamic engine-face distortion. Advanced tactical aircraft are likely to use thrust vectoring to enhance their maneuverability. As a result, the engines will see more extreme aircraft angles-of-attack and sideslip levels than are currently encountered with present-day aircraft. Also, the mixed-compression inlets needed for the High Speed Civil Transport will likely encounter disturbances similar to those seen by tactical aircraft, in addition to planar pulse, inlet buzz, and high distortion levels at low flight speed and off-design operation. The current approach of incorporating a sufficient component design stall margin to tolerate these increased levels of distortion would significantly reduce performance. The objective of the High Stability Engine Control (HISTEC) program is to design, develop, and flight demonstrate an advanced, high-stability, integrated engine-control system that uses measurement-based, real-time estimates of distortion to enhance engine stability. The resulting distortion-tolerant control reduces the required design stall margin, with a corresponding increase in performance and decrease in fuel burn. The HISTEC concept has been designed and developed, and the software implementing the concept has successfully accommodated time-varying distortion. The NASA Lewis Research Center is currently overseeing the development and validation of the hardware and software necessary to flight test the HISTEC concept. HISTEC is a contracted effort with Pratt & Whitney of West Palm Beach, Florida. The HISTEC approach includes two major systems: A Distortion Estimation System (DES) and Stability Management Control (SMC). DES is an aircraft-mounted, high-speed processor that estimates the amount and type of distortion present and its effect on the engine. It uses high-response pressure measurements at the engine face to calculate indicators of the type and extent of distortion in real time. From these indicators, DES determines the effects of distortion on the propulsion systems and the corresponding engine match point necessary to accommodate it. DES output consists of fan and compressor pressure ratio trim commands that are passed to the SMC. In addition, DES uses maneuver information, consisting of angle-of-attack and sideslip from the flight control, to anticipate high inlet distortion conditions. The SMC, which is contained in the engine-mounted, Improved Digital Electronic Engine Control (IDEEC), includes advanced control laws to directly control the fan and compressor transient operating line (pressure ratio). These advanced control laws, with a multivariable design, have the potential for higher bandwidth and the resulting more precise control of engine match. The ability to measure and assess the distortion effects in real time coupled with a high-response controller improves engine stability at high levels of distortion. The software algorithms implementing DES have been designed, developed, and demonstrated, and integration testing of the DES and SMC software has been completed. The results show that the HISTEC system will be able to sense inlet distortion, determine the effect on engine stability, and accommodate distortion by maintaining an adequate margin for engine surge. The Pratt &Whitney Comprehensive Engine Diagnostic Unit was chosen as the DES processor. An instrumented inlet case for sensing distortion was designed and fabricated. HISTEC is scheduled for flight test on the ACTIVE F-15 aircraft at the NASA Dryden Flight Research Center in Edwards, California, in late 1996.
Subsonic and supersonic wind tunnel study of low aspect ratio sweptback wing tailless fighter aircraft model/stability and control
Liapunov stability theory applied to control system, noting stability of function and stochastic differential equations
The results of wind-tunnel investigations on the stability and control characteristics of externally blown jet-flap configurations are presented. Conventional wind-tunnel tests and free-flight model tests have shown that longitudinal trim and stability can be achieved by a properly located horizontal tail of sufficient size, and that lateral trim in the engine-out condition can be produced by combinations of differential flap, spoiler, and rudder deflection. Free-flight model tests have revealed a lightly damped Dutch roll lateral oscillation, and have shown that the oscillation can be stabilized by use of artificial damping.
Explore the source record for details and available documents.
Flight investigation of the longitudinal stability and control characteristics of a four-propeller tilt-wing vtol model with programmed flap
In the present state of the design of tailless airplanes, it appears that: (1) Sweepback affords a method of supplying tail length for directional and longitudinal stability and control and allows the utilization of a high-lift flap but introduces undersirable tip stalling tendencies that must be overcome before the advantages of sweepback can be realized. (2) The damping in pitching appears to have little effect on the longitudinal behavior of the airplane provided the static margin is never permitted to become negative. (3) The directional stability must be as great as for conventional airplanes if the same requirements regarding satisfactory stability and control characteristics are to be adhered to. (4) The influence of the lateral resistance and the damping in yawing on the flying qualities is somewhat obscure.
The purpose of the present investigation was to parametrically study the stability and control characteristics of a forward-swept wing three-surface turboprop model through an extended angle of attack range, including the deep-stall region. As part of a joint research program between North Carolina State University and NASA Langley Research Center, a low-speed wind tunnel investigation was conducted with a three-surface, forward-swept wing, aft-mounted, twin-pusher propeller, model, representative of an advanced turboprop configuration. The tests were conducted in the NASA Langley 12-Foot Low-Speed Wind Tunnel. The model parameters varied in the test were horizontal tail location, canard size, sweep and location, and wing position. The model was equipped with air turbines, housed within the nacelles and driven by compressed air, to model turboprop power effects. A three-surface, forward-swept wing configuration that provided satisfactory static longitudinal and lateral/directional stability was identified. The three-surface configuration was found to have greater longitudinal control and increased center of gravity range relative to a conventional (two-surface) design. The test showed that power had a large favorable effect on stability and control about all three axis in the post-stall regime.
Airframe/propulsion system interactions can strongly affect the stability and control of supersonic cruise aircraft. These interactions generate forces and moments similar in magnitude to those produced by the aerodynamic controls, and can cause significant changes in vehicle damping and static stability. This in turn can lead to large aircraft excursions or high pilot workload, or both. For optimum integration of an airframe and its jet propulsion system, these phenomena may have to be taken into account.
Facilities used in the dynamic testing of the orbiting astronomical observatory /oao/ stabilization and control subsystem
Low-speed static stability and control characteristics of two small-scale, hypersonic cruise vehicles
An experimental evaluation of analytical techniques for predicting certain stability and control characteristics of a large flexible aircraft is presented. Analytical methods based on both the model approach and flexibility influence coefficients are developed to predict the aerodynamic characteristics of a flexible airplane. These methods are then applied to a flexibly scaled model of a supersonic transport configuration. Comparisons of wind-tunnel data, calculations based on the model approach, and flexibility influence coefficients are presented over the Mach number range from 0.6 to 2.7. An examination of the results obtained from this study indicates that both analytical techniques predict reasonably well the effect of flexibility on the basic longitudinal characteristics and that both techniques give generally comparable results.
Wind tunnel tests were conducted to determine the stability and control characteristics of a monoplane missile with large delta wings and various tail configurations. The tests were conducted at angles of attack of approximately 24 degrees and angles of sideslip of about 22 degrees. Tail control configurations were the cruciform, conventional airplane type, and an inverted airplane configuration. Control effectiveness was measured for pitch, yaw, and roll.
Estimates of longitudinal stability and control parameters for the space shuttle were determined by applying a maximum likelihood parameter estimation technique to Challenger flight test data. The parameters for pitching moment coefficient, C(m sub alpha), (at different angles of attack), pitching moment coefficient, C(m sub delta e), (at different elevator deflections) and the normal force coefficient, C(z sub alpha), (at different angles of attack) describe 90 percent of the response to longitudinal inputs during Space Shuttle Challenger flights with C(m sub delta e) being the dominant parameter. The values of C(z sub alpha) were found to be input dependent for these tests. However, when C(z sub alpha) was set at preflight predictions, the values determined for C(m sub delta e) changed less than 10 percent from the values obtained when C(z sub alpha) was estimated as well. The preflight predictions for C(z sub alpha) and C(m sub alpha) are acceptable values, while the values of C(z sub delta e) should be about 30 percent less negative than the preflight predictions near Mach 1, and 10 percent less negative, otherwise.
Results of an investigation to determine the static longitudinal stability and control characteristics of an aspect-ratio-2 triangular wing and body configuration equipped with either a canard control, a trailing-edge-flap control, or a cambered forebody are presented without analysis for Mach numbers from 0.70 to 2.22. The canard surface had a triangular plan form and a ratio of exposed area to total wing area of 7.8 percent. The hinge line of the canard was in the extended wing chord plane, 0.83 wing mean aerodynamic chord ahead of the reference center of moments. The trailing-edge controls were constant-chord full-span flaps with exposed area equal to 10.7 percent of the total wing area. The cambered body was a modified Sears-Haack body with camber only ahead of the wing apex. Data are presented for various canard and flap deflections at angles of attack ranging from -6 deg to +18 deg.
A brief overview of a cooperative NASA/Boeing research effort, Strake Technology Research Application to Transport Aircraft (STRATA), intended to explore the potential of applying forebody strake technology to transport aircraft configurations for directional stability and control at low angles of attack, is presented. As an initial step in the STRATA program, an exploratory wind-tunnel investigation of the effect of fixed forebody strakes on the directional stability and control characteristics of a generic transport configuration was conducted in the NASA Langley 12-Foot Low-Speed Wind Tunnel. Results of parametric variations in strake chord and span, as well as the effect of strake incidence, are presented. The use of strakes for yaw control is also discussed. Results emphasize the importance of forebody/fuselage crossflow in influencing strake effectiveness. Strake effectiveness is also seen to be directly related to its span, but less sensitive to chord; a very short-chord strake with sufficient span can have a significant effect.