Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “composition and microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

3D Printing of Inconel 718 with Enhanced Boron Composition as a Novel Solar Absorber Tube Material in the Concentrated Solar Power (CSP) System

The growing demands for elevated efficiency in the solar energy industry led researchers to focus on the development of functional solar absorber tube material in concentrated solar power (CSP) systems, when molten salts are adopted as the heat transfer fluid. In this study, the typical solar absorber tube material, Inconel 718, was enhanced with boron to achieve a higher solar absorptivity in the visible light spectrum. Combined with an additive manufacturing (AM) method, the boron composition exceeded the traditional manufacturing limit of 60 ppm without microstructural defects. The boron-enhanced Inconel 718 exhibited a high solar absorptivity of nearly 90 % while maintaining a high thermal cycle fatigue resistance after thermal cycling treatment between 550°C and 720°C. The boron composition was increased to the manufacturing failure point, and the effects of different boron compositions on mechanical properties, microstructure, and optical properties were studied. The provided microstructure-property map in this study delivers high potentials of functional AM-printed alloy material in CSP applications.

13 HYDRO ENERGY↗
DOE OSTI2024

Sulphate resistance of low‐clinker engineered cementitious composites examined by MicroXRF imaging

Abstract Engineered cementitious composites (ECC) are a class of high‐performing fibre‐reinforced cementitious materials recognised for their increased ductility and durability compared to conventional cement‐based materials, owing to their autogenously controlled tight crack widths, even when subjected to high strains. To reduce ECC's environmental impact, this research examines the use of a low‐clinker binder − limestone‐calcined clay cement (LC3) − as an alternative to portland cement (PC), along with fly ash to further reduce the clinker proportion and the embodied CO 2 of the formulations. In conventional concrete, LC3 hydrates to a denser microstructure resulting from the synergistic reaction between limestone and calcined clay. At the lower water contents typical of ECC and with the presence of fly ash, the influence of the binder composition on the microstructure is difficult to anticipate. To examine the influence of these compositional variables on microstructure, permeability and durability, the sulphate resistance of LC3‐based ECC is explored. Specifically, the ECC‐LC3 blends are designed with high clinker replacement rate of 75% by mass of binder and contain either conventional fly ash or reclaimed fly ash at 50% by mass of binder. Expansion of ECC‐LC3 samples subjected to standard sodium sulphate test conditions was measured up to 12 months and the depth of penetration of sulphates into the ECC‐LC3 of varying compositions was quantified using micro‐X‐Ray Fluorescence (microXRF) imaging and modelling. The expansion results show that the ECC‐LC3 formulations performed better than the PC samples and can provide adequate resistance to external sulphate attack, even when reclaimed fly ashes are used in place of the conventional ash. In addition, the shallow penetration of sulphate into these cementitious composites demonstrates the low diffusion coefficients values that were determined using the quantitative data from MicroXRF imaging.

Microscopy↗
DOE OSTI2025

A deep learning and finite element approach for exploration of inverse structure–property designs of lightweight hybrid composites

Hybrid composites have important applications, such as high-performance and lightweight materials in aerospace and automotive industries. Hybrid composites utilize the synergy of diverse fillers to achieve desired material properties, but usually have more complicated microstructures. While topology optimization can optimize a particular property, designing hybrid composites for customized mechanical performances, e.g. full-range stress–strain curve, remains challenging. Here, a computational framework that integrated finite element analysis (FEA) and artificial intelligence (AI) methods of Conditional Generative Adversarial Networks (cGAN) deep learning and transfer learning was developed to establish inverse structure–property relationships and design tailor-made hybrid composites. Based on FEA-generated datasets of hybrid fiber-particle–matrix microstructures and their corresponding full-range stress–strain curves, a cGAN architecture was trained to generate tailored microstructures and establish structure–property relationships. Similarity in microstructural features and well-matched stress–strain curves based on the AI-generated composites were achieved. In conclusion, transfer learning was used to expand the pre-trained model for designing different materials systems.

Hybrid composites↗
DOE OSTI2020

Characterization of Mechanical Performance of Composites Fabricated Using Innovative Carbon Fiber Wet Laid Process

Recent innovation in production of optimized nonwoven wet laid (WL) carbon fiber (CF) mats raised the question of optimal translation of the performance and isotropy into composites formed through these dry preforms. This work explores the mechanical behavior of composites produced from WL-CF mats in conjunction with the microstructure predicted through Object Oriented Finite Element Analysis (OOF). The mats used for the composites were prepared in two dispersion regimes using 25.4 mm long CF. The mixing regimes discussed in the author’s previous work, are identified as Method 1 for the traditional processing regime and Method 2 for the innovative regime that provided optimal nonwoven WL-CF mats. Composite panels from Method 2 mats showed a normalized tensile strength increase of 52% over those from Method 1 panels. Reproducibility analysis of composites made from Method 2 mats demonstrated a standard deviation of 2% in fiber weight content, 2% in tensile modulus and 9% in tensile strength, while composites made from Method 1 mats demonstrated a standard deviation of 5% in fiber weight content, 5% in tensile modulus and 17% in tensile strength. Systematic study of the microstructure and its analysis through OOF confirmed the isotropy translation of mats produced through method 2 to the composites. This study validated the hypothesis that optimal nonwoven mats lead to a well-balanced composite with optimal performance and that non-optimal nonwoven mats do not pack into a well-balanced composite.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Toward a circular economy: zero-waste manufacturing of carbon fiber-reinforced thermoplastic composites

Fiber-reinforced composites are becoming ubiquitous as a way of lightweighting in the wind, aerospace, and automotive industries, but current recycling technologies fall short of a circular economy. In this work, fiber-reinforced composites made of recycled carbon fiber and polyphenylene sulfide were recycled and remanufactured using common processing technologies such as compression and injection molding. An industrially viable size-exclusive sieving technique was used to retain fiber length and reduce variability in the mechanical properties of the remanufactured composites. Fiber length reduction alone could not explain the strength reductions apparent in the composites, which we propose are due to microstructural inhomogeneity as defined by poor dispersion of the fibers. Future recycling efforts must focus on fiber length retention and good dispersion to make composite remanufacturing a viable path toward a circular economy.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Structural, Thermal, and Mechanical Characterization of a Thermally Conductive Polymer Composite for Heat Exchanger Applications

Polymer composites are being considered for numerous thermal applications because of their inherent benefits, such as light weight, corrosion resistance, and reduced cost. In this work, the microstructural, thermal, and mechanical properties of a 3D printed polymer composite with high thermal conductivity are examined using multiple characterization techniques. Infrared spectroscopy and X-ray diffraction reveal that the composite contains a polyphenylene sulfide matrix with graphitic fillers, which is responsible for the high thermal conductivity. Furthermore, differential scanning calorimetry determines that the glass transition and melting point of the composite are 87.6 °C and 285.6 °C, respectively. Thermogravimetric analysis reveals that the composite is thermally stable up to ~400 °C. Creep tests are performed at different isotherms to evaluate the long-term performance of the composite. The creep result indicates that the composite can maintain mechanical integrity when used below its glass transition temperature. Nanoindentation tests reveal that modulus and hardness of the composite is not significantly influenced by heating or creep conditions. These findings indicate that the composite is potentially suitable for heat exchanger applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Printing noble metal alloy films with compositional gradient

Additive manufacturing has offered great promise in fabricating materials and devices with complex structures and unique properties. In addition to complex structures, additive manufacturing also allows for local changes to material compositions and/or structure, ideal for combinatorial material investigations. Besides, advantages over freedom of design, mass customization, waste minimization and the capability to fast prototyping, the on-demand control of compositional distributions in low dimensional materials remains challenging. In this work, we demonstrate a combinatorial aerosol jet printing technique to create noble metal films with gradient compositions. Nanoparticle sizes and ink chemistry are critical for aerosol jet printing and sintering process in order to achieve defect free thin films. Ruthenium (Ru) and platinum (Pt) nanoparticles with size <5 nm were synthesized and formulated into printable inks. Further, after thermal sintering at temperature as low as 400 °C, printed nanoparticles formed highly reflective films free from microstructural defect. Alloy films of gradient compositions were realized via in-situ mixing Ru and Pt ink streams and varying the mixing ratio during the printing process. This combinatorial printing method provides great potential to rapidly transform nanoparticle inks into new materials compositions and structures unobtainable via conventional methods for high-throughput materials studies.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Installing Controlled Stereo-Defects Yields Semicrystalline and Biodegradable Poly(3-Hydroxybutyrate) with High Toughness and Optical Clarity

Stereo-defects present in stereo-regular polymers often diminish thermal and mechanical properties, and hence suppressing or eliminating them is a major aspirational goal for achieving polymers with optimal or enhanced properties. Here, we accomplish the opposite by introducing controlled stereo-defects to semicrystalline biodegradable poly(3-hydroxybutyrate) (P3HB), which offers an attractive biodegradable alternative to semicrystalline isotactic polypropylene but is brittle and opaque. We enhance the specific properties and mechanical performance of P3HB by drastically toughening it and also rendering it with the desired optical clarity while maintaining its biodegradability and crystallinity. This toughening strategy of stereo-microstructural engineering without changing the chemical compositions also departs from the conventional approach of toughening P3HB through copolymerization that increases chemical complexity, suppresses crystal-lization in the resulting copolymers, and is thus undesirable in the context of polymer recycling and performance. More specifically, syndio-rich P3HB (sr-P3HB), readily synthesized from the eight-membered meso-dimethyl diolide, has a unique set of stereo-microstructures comprising enriched syndiotactic [rr] and no isotactic [mm] triads but abundant stereo-defects randomly distributed along the chain. This sr-P3HB material is characterized by high toughness (UT = 96 MJ/m 3 ) as a result of its high elongation at break (>400%) and tensile strength (34 MPa), crystallinity (T m = 114 degrees C), optical clarity (due to its submicron spherulites), and good barrier properties, while it still biodegrades in freshwater and soil.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Unveiling the microstructural evolution of carbon fibers derived from polyamide-6

Polyacrylonitrile-based carbon fibers have dominated the industry for decades, but the high cost of polyacrylonitrile has prevented the widespread adoption of carbon fiber in high-volume structural applications. As such, a significant amount of research has been dedicated to finding an alternative, low-cost carbon fiber precursor. In this work, carbon fibers were produced from polyamide-6 using metal salt impregnation and a thermo-oxidative stabilization step. To gain further insight into the carbonization process and microstructural transformation, the morphologies, crystallinities, elemental compositions, and thermal stabilities of the fibers were characterized at various stages of processing. The stabilization step resulted in a significant increase in carbon yield, indicating a dramatic increase in thermal stability. This is due to the crosslinking of polyamide-6 chains, which was confirmed by functional group analysis. The crystallinity of the fibers was also significantly altered during processing, as the produced carbon fibers consisted of pseudo-amorphous carbon with two distinct regions of metal salt impregnation. Finally, the findings and microstructural evolution mechanisms provide guidelines for further research into carbon fiber produced from polyamide-6.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Processing and properties of SiC composites made via binder jet 3D printing and infiltration and pyrolysis of preceramic polymer

The effect of polymer infiltration and pyrolysis (PIP) cycles with polycarbosiloxane on the microstructure, air leak rate, and properties of SiC composites manufactured by a combination of binder jet 3D printing and PIP are reported. The density, Young’s modulus and flexural strength of disk-shaped components increased with the number of PIP cycles. In the case of density, it increased from 2.05 g/cm 3 in one PIP cycle to 2.33 g/cm 3 after three PIP cycles, while values of flexural strength and Young’s modulus at room temperature after three PIP cycles reached 66.8 ± 2.5 MPa and 69.5 ± 2.8 GPa, respectively. Conversely, the air leak rate was found to decrease with number of PIP cycles, and it reached a value of 4 mbar-liter/s after three cycles. The instantaneous coefficient of thermal expansion of the composite was found to change minimally with the number of PIP cycles and had a value of 4 ± 1.2 ppm/°C between 200°C and 1,000°C. Thermal conductivity was found to increase with number of PIP cycles and to decrease with temperature. For example, after 3 PIP cycles it was found to change from 6.72 ± 0.08 to 6.98 ± 0.08 W/mK at 25°C and 7.36 ± 0.08 to 7.96 ± 0.08 W/mK at 300°C. These values were lower than those of crystalline SiC because of the amorphous nature of the matrix and the presence of pores and cracks.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Characterization of Build Parameters and Microstructure in Low Heat Input WAAM of Ni-Based Superalloy Haynes 282

Ni-based superalloy Haynes® 282® is being targeted for various applications in advanced power generation systems for its superior fabricability, weldability, and excellent high temperature creep and corrosion performance. This process optimization study aims to use a low heat-input, high deposition rate, controlled Gas Metal Arc Welding (GMAW) process, Cold Metal Transfer (CMT) by Fronius, attempting to achieve fully dense fabrication and possibly avoid the need for HIP. Twenty-one multilayer blocks (~25x100x40 mm3) were deposited to explore a large set of build parameters variations that focused on varying the travel speed from 14 to 42 inches per minute (ipm) and wire feed speed from 150 to 450 ipm. A strong correlation has been observed between arc energy – controlled primarily by travel and wire feed speed. Initial visual inspection, internal microstructural examination, and computed tomography (CT) have been used to determine the effects of built parameters on evolution of internal porosity and defects. Scanning electron microscopy techniques enabled structural and compositional imaging of heterogeneity and changes in microstructural properties.

additive manufacturing↗
DOE OSTI2025

Characterization of Build Parameters and Microstructure in Low Heat Input WAAM of Ni-Based Superalloy Haynes 282

Ni-based superalloy Haynes® 282® is being targeted for various applications in advanced power generation systems for its superior fabricability, weldability, and excellent high temperature creep and corrosion performance. This process optimization study aims to use a low heat-input, high deposition rate, controlled Gas Metal Arc Welding (GMAW) process, Cold Metal Transfer (CMT) by Fronius, attempting to achieve fully dense fabrication and possibly avoid the need for HIP. Twenty-one multilayer blocks (~25x100x40 mm3) were deposited to explore a large set of build parameters variations that focused on varying the travel speed from 14 to 42 inches per minute (ipm) and wire feed speed from 150 to 450 ipm. A strong correlation has been observed between arc energy – controlled primarily by travel and wire feed speed. Initial visual inspection, internal microstructural examination, and computed tomography (CT) have been used to determine the effects of built parameters on evolution of internal porosity and defects. Scanning electron microscopy techniques enabled structural and compositional imaging of heterogeneity and changes in microstructural properties.

additive manufacturing↗
DOE OSTI2020

Tailoring ductile-phase toughened tungsten hierarchical microstructures for plasma-facing materials

Biological materials, such as bones, nacre, etc., have been found to show attractive and unique combinations of stiffness, strength and fracture toughness. Research has been conducted in various engineering areas to mimic the naturally hierarchical microstructures or nanostructures of these materials to produce materials with optimum stiffness, high strength and fracture toughness for their intended structural applications. In the same objective, this work applies a multiscale microstructural approach recently developed to investigate the deformation and fracture behavior of ductile phase toughened tungsten (W) materials such as tungsten-nickel/iron (W-Ni/Fe) composites that possess lamellar-like and hierarchical “brick-and-mortar” (BAM) microstructures. First, the approach is used to simulate tensile loading of W-Ni/Fe specimens cut out from hot-rolled W-Ni/Fe plates which possess lamellar-like microstructures. The finite element model of the gage section of the specimen consists of a W-Ni/Fe dual-phase microstructural domain in which the constitutive behaviors of W and Ni/Fe phases are described by an elastic-plastic damage model. The predicted material stress-strain response and crack pattern development as a function of loading are then compared to the corresponding experimental results to determine the constitutive model parameters for W and Ni/Fe. Subsequently, the model parameters are used to analyze W-Ni/Fe BAM microstructures that are artificially created to investigate the effects of microstructural features and morphologies on the composite stress-strain response, damage, and fracture patterns. The modeling shows that regular BAM microstructures that experience bridging mechanism combined with crack penetration across W-phase regions exhibit significantly higher strengths than the rather random lamellar-like microstructures. More significantly, however adjusting the brick’s length-to-height ratio, the BAM microstructure can be designed to allow a more distributed damage zone which leads to increased strength, ductility and fracture energy.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Recent Progress in Solid‐State Lithium Batteries through Cathode Microstructure Engineering

A high‐performance cathode is necessary to realize the great potentials of solid‐state batteries such as high energy density and long cycle life. It is also needed to validate electrolyte performance, which is lacking. Currently, cathodes for solid‐state batteries are thinner and have lower cathode active material content than their lithium‐ion battery counterpart, resulting from insufficient conductivity and limiting the battery energy density. This review article provides an overview of recent development in cathode microstructures and their impact on battery properties, including compatibility between cathode and electrolyte, cathode architecture design, interface engineering, correlation between material properties, cathode processing approaches, and performance, as well as the advanced characterization methods used to understand the above correlations . Some perspectives on future development are shared including utilizing in situ and operando characterization tools to better understand dynamic evolution of the cathode/electrolyte interface, adapting artificial intelligence and machine learning to design and optimize cathode structures. The article is aimed to promote research interest on cathode development and advance solid‐state battery technologies.

cathode engineering↗
DOE OSTI2024

Theory-guided design of duplex-phase multi-principal-element alloys

Density-functional theory (DFT) is used to identify phase-equilibria in multi-principal-element and high-entropy alloys (MPEAs/HEAs), including duplex-phase and eutectic microstructures. Here, a combination of composition-dependent formation energy and electronic-structure-based ordering parameters were used to identify a transition from FCC to BCC favoring mixtures, and these predictions experimentally validated in the Al-Co-Cr-Cu-Fe-Ni system. A sharp crossover in lattice structure and dual-phase stability as a function of composition were predicted via DFT and validated experimentally. The impact of solidification kinetics and thermodynamic stability was explored experimentally using a range of techniques, from slow (castings) to rapid (laser remelting), which showed a decoupling of phase fraction from thermal history, i.e., phase fraction was found to be solidification rate-independent, enabling tuning of a multi-modal cell and grain size ranging from nanoscale through macroscale. Strength and ductility tradeoffs for select processing parameters were investigated via uniaxial tension and small-punch testing on specimens manufactured via powder-based additive manufacturing (directed-energy deposition). This work establishes a pathway for design and optimization of next-generation multiphase superalloys via tailoring of structural and chemical ordering in concentrated solid solutions.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Geochemical and Microstructural Characterization of Shale Rock: A Workflow for Site Evaluation for Energy–Fluids Storage

Shales are a central component of petroleum systems, as source, seal, and unconventional reservoir rocks. Unlike traditional unconventional shale, a newly emerging Caney Shale play is regarded as an unconventional of unconventional shales (UUS), due to its high content of fine-grained materials, lower reservoir porosity, dominance of nanopores, and a scarcity of visible natural fractures. Other developed unconventional shales such as the Woodford and Barnett have larger average pore size, higher porosity, and extensive natural fractures at core scale that contribute to reservoir quality. In this work, the Caney Shale was cored in entirety to characterize its interbedded ductile and reservoir intervals and establish criteria for their recognition. Representative ductile and reservoir intervals known as D2 and R3, respectively, were selected for detailed analysis including variations in elemental composition, mineralogy, facies, and the presence of natural fractures at well and core scales using X-ray fluorescence, X-ray diffraction, and thin section and core description. Characteristics of microstructure and microgeochemistry at nano- and microscales are compared using field emission scanning electron microscopy with energy dispersive spectroscopy and lowpressure nitrogen adsorption isotherms with fractal dimension analysis. The ductile (detrital clay-rich) member D2 is characterized by higher concentrations of Ti and Al and lower Si, while the reservoir R3 (possibly biogenic silica-accumulated) is characterized by lower Ti and Al and higher Si. Eight mixed carbonate–siliciclastic facies are recognized, and R3 shows a higher heterogeneity of facies stacking and average fracture abundance than D2. Further, R3 shows a more microscopically heterogeneous fabric/texture of matrix and a higher microporosity than D2 that has a higher pore surface heterogeneity. A fundamental understanding of the compositional and microstructural characteristics of UUS and further ductile/reservoir intervals will allow for a better assessment of reservoir quality, more effective production of hydrocarbons, and optimized selection of safe caprocks in carbon sequestration and subsurface hydrogen storage.

58 GEOSCIENCES↗
DOE OSTI2022

Increasing the composition range of a novel τ 11 -Al 4 Fe 1.7 Si alloy with additions of Mn

Automotive applications need low-cost, lightweight, high-temperature alloys to increase vehicle efficiency. The Al–Fe–Si system provides an opportunity to develop such a material, as it consists of three low-cost elements that are all abundant in nature. Specifically, the τ 11 -Al 4 Fe 1.7 Si ternary intermetallic phase is a high-temperature, lightweight phase with high strength and good corrosion resistance. However, this phase exhibits a narrow compositional range of stability, resulting in undesirable microstructures forming during solidification and processing, limiting its use in potential applications. Density functional theory (DFT) calculations and a thermodynamically-driven experimental approach utilizing diffusion couples were employed to study the effect of Mn on the stability and composition range of τ 11 -Al 4 Fe 1.7 Si. The DFT calculations showed a decrease in the energy of the structure when alloying with Mn. Experimental results confirmed the predictions from the DFT calculations, indicating that alloying with Mn increases the compositional range, and thus the processability of this phase. New phase diagrams and equilibria are proposed by exploring and determining phase boundaries for the τ 11 -Al 4 Fe 1.7 Si phase with Mn.

36 MATERIALS SCIENCE↗