SEARCH · Engineering Papers

Results for “cloud radiative effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

All sources NASA NTRS DOE OSTI

DOE OSTI2020

Assessing Global and Local Radiative Feedbacks Based on AGCM Simulations for 1980–2014/2017

In order to avoid contamination of unobservable and uncertain effective radiative forcing (ERF) on the diagnosis of radiative feedbacks based on short-term climate variability, we verify the Kernel-Gregory feedback calculation method using atmospheric model experiments with prescribed ERF. We show that both clear-sky radiative fluxes and all-sky radiative feedbacks have a closure between model simulations and kernel derivations. A near-zero global mean net cloud feedback is found in the simulation with prescribed ERF, which results in a more negative global net climate feedback, -2 W m -2 K -1 . Consistent with AMIP6 ensemble mean results, the lapse rate feedback is the largest contributor among all feedbacks to temperature amplification over the three poles (Arctic, Antarctic and Tibetan Plateau), followed by surface albedo feedback and Planck feedback deviation from its global mean. Except for the higher surface albedo feedback in the Antarctic, other feedbacks are almost same between the Arctic and Antarctic.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2021

Southern Ocean Cloud Properties Derived From CAPRICORN and MARCUS Data

The properties of Southern Ocean (SO) liquid phase non precipitating clouds (hereafter clouds) are examined using shipborne data collected during the Measurements of Aerosols, Radiation and Clouds over the Southern Ocean and the Clouds Aerosols Precipitation Radiation and atmospheric Composition Over the SoutheRN ocean I and II campaigns that took place south of Australia during Autumn 2016 and Summer 2017–2018. Cloud properties are derived using data from W-band radars, lidars, and microwave radiometers using an optimal estimation algorithm. The SO clouds tended to have larger liquid water paths (LWP, 115 ± 117 g m -2 ), smaller effective radii (re, 8.7 ± 3 μm), and higher number concentrations (N d , 90 ± 107 cm-3) than typical values of eastern ocean basin stratocumulus. The clouds demonstrated a tendency for the LWP to increase with Nd presumably due to precipitation suppression up to Nd of approximately 100 cm -3 when mean LWP decreased with increasing Nd. Due to higher optical depth, cloud albedos were less susceptible to changes in Nd compared to subtropical stratocumulus. The highest latitude clouds of the datasets, observed along and near the Antarctic coast, presented a distinctly bimodal character. One mode had the properties of marine clouds further north. Additionally, the other mode occurred in an aerosol environment characterized by high cloud condensation nuclei concentrations and elevated sulfate aerosol without obvious continental aerosol markers. These regions of higher cloud condensation nuclei tended to have higher Nd, smaller re and higher LWP suggesting sensitivity of cloud properties to seasonal biogenic aerosol production in the high latitude SO.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2025

Enhanced Convective Microphysics Scheme and Its Impacts on Mean Climate in E3SM

Abstract To improve the representation of microphysical processes in convective clouds and their interaction with aerosol and stratiform clouds, a two‐moment convective microphysics parameterization (CMP) scheme developed by Song and Zhang (2011, https://doi.org/10.1029/2010jd014833 ) is upgraded and implemented in E3SM. The new developments include: (a) implementing a parameterization for graupel to enhance the representation of ice‐phase microphysical processes; (b) representing the impact of spatial inhomogeneity of cloud droplets in cumulus ensembles on autoconversion and accretion processes to improve the representation of warm‐rain microphysical processes; (c) implementing a comprehensive Bergeron process parameterization to better represent mixed‐phase microphysical processes; and (d) representing the interactions between ice‐phase microphysics and cloud thermodynamics. Simulations show that the cloud microphysical properties simulated by the CMP are generally in good agreement with observations. It reasonably simulates the changes in droplets effective radius related to precipitation formation in convective clouds, as identified from satellite observations. It also successfully simulates the contrast in these processes between maritime and continental clouds, demonstrating its capability to simulate the impact of aerosols on convection. Analyses of the impact of CMP on climate mean state simulation demonstrate that the CMP slightly improves the simulations of precipitation, cloud macrophysical properties, longwave cloud radiative forcing, zonal wind, and temperature. However, a degradation in shortwave cloud radiative forcing occurs.

GCM↗

DOE OSTI2024

Modeling Diurnal and Annual Ethylene Generation from Solar-Driven Electrochemical CO 2 Reduction Devices

Integrated solar fuels devices for CO 2 reduction (CO 2 R) are a promising technology class towards achieving net-negative carbon emissions. Designing integrated CO 2 R solar fuels devices requires careful co-design of electrochemical and photovoltaic components as well as consideration of the diurnal and seasonal effects of solar irradiance, temperature, and other meteorological factors expected for ‘on-sun’ deployment. Here, using a photovoltaic-electrochemical (PV-EC) platform, we developed a temperature and potential-dependent diurnal and annual model using experimental CO 2 R performance of Cu-based electrocatalysts, local meteorological data from the National Solar Radiation Database (NSRD), and modeled performance of commercial c-Si PVs. We simulated diurnal product outputs with and without the effects of ambient temperature to determine gaseous product temperature sensitivity. From these outputs, we observed seasonal variation in gaseous product generation, with up to two-fold increases in ethylene productivity between the Winter and Summer, analyzed the consequences of dynamic cloud coverage, and identified periods where device cooling/heating mechanisms could be implemented to maximize ethylene generation. Finally, we modeled the annual ethylene generation for a scaled 1 MW solar farm at three different locations (Beijing, CN; Sydney, AUS; Barstow, CA) to determine the consequences of local meteorological climates on PV-EC CO 2 R product output, recording a maximum ethylene output of 18.5 tonne/yr at Barstow. Overall, this model presents a critical tool for streamlining the translation of experimental solar-driven electrochemical research to real-world implementation.

Yap, Kyra M. K.↗

DOE OSTI2020

An Observational Comparison of Level of Neutral Buoyancy and Level of Maximum Detrainment in Tropical Deep Convective Clouds

Tropical deep convective clouds are important drivers of large-scale atmospheric circulation representing the main vertical transport pathway through the depth of the troposphere for heat, momentum, water, and chemical species. The strength and depth of this transport are impacted by the convective updraft size and intensity that are driven by buoyancy, dynamical forcing, and mixing of environmental air, i.e., entrainment. In this paper, we identify tropical deep convective systems with well-defined forward anvils using Atmospheric Radiation Measurement (ARM) ground-based profiling radars, at three ARM fixed-sites in the Tropical Western Pacific (TWP; i.e., Manus, Nauru, Darwin) and three ARM Mobile Facility deployments in Niamey, Niger; Gan Island, Maldives; and Manacapuru, Brazil. We use the difference between the level of neutral buoyancy (LNB) and the level of maximum detrainment (LMD) as a proxy for the effective bulk convective entrainment (εproxy). The LNB, the theoretical height that a parcel raised above the level of free convection would reach with no mixing, is calculated based on pre-convection radiosonde measurements using parcel theory. The LMD is the height of the maximum reflectivity observed in forward anvil clouds by profiling radars. Deep convective systems over the TWP show higher LNBs that extend to 16.3 km on average and larger εproxy (median LNB minus LMD up to 6.5 km) compared to their continental counterparts in the Amazon and West Africa. Oceanic conditions show larger convective available potential energy (CAPE) coupled with higher moisture at low levels which favors larger εproxy. In contrast, continental cases initiate and develop under high convective inhibition, steeper environmental lapse rate, and high wind shear conditions, which show smaller offset between LNB and LMD. Deep convective cases that promote significant cold pools at the surface experience less εproxy. Using a Random Forest regression algorithm, CAPE is associated with the highest feature importance score for predicting convective εproxy, followed by low-level relative humidity. For continental cases, the low-level wind shear also indicates higher importance.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2025

Multiscale ACI Satellite Database

The SATELLITE_EAGLES_PNNL NetCDF dataset contains a suite of satellite- and reanalysis-derived atmospheric and surface parameters on a regular latitude–longitude grid. The dataset includes core geophysical fields such as land fraction, aerosol optical depth at multiple wavelengths (465, 550, 667, and 865 nm), sea surface temperature, estimated inversion strength, and various thermodynamic and dynamic quantities (e.g., relative humidity, vertical velocity, boundary-layer height, and surface fluxes) from both MERRA and ERA reanalysis products, provided as daily-mean and instantaneous values. A major component of the dataset consists of MODIS-retrieved cloud microphysical properties, including cloud droplet number concentration, cloud effective radius, optical thickness, and liquid water path, provided for three compositing regimes (“All,” “Q06,” and “G18”). Corresponding cloud-top parameters—temperature, height, and pressure—along with total and domain-mean cloud fraction fields are also included. The file further integrates additional satellite data from AMSR-E (for cloud water, rain water, and surface precipitation retrievals) and CERES (for top-of-atmosphere radiative fluxes, cloud fractions, and albedo). This dataset is designed to evaluate aerosol–cloud interactions in warm clouds, emphasizing the use of MODIS for deriving cloud droplet number concentration and liquid water path statistics. The complementary satellite and reanalysis fields are co-located and time-matched to the same instantaneous MODIS observations, enabling consistent comparisons between cloud properties, aerosol loading, and large-scale meteorological conditions. The dataset is recently featured in Christensen et al. (2025), Machine Learning Reveals Strong Grid-Scale Dependence in the Satellite Nd–LWP Relationship, EGUsphere [preprint], https://doi.org/10.5194/egusphere-2025-3850, 2025.

Christensen, Matthew [Pacific Northwest National L↗

DOE OSTI2025

Multiscale ACI Satellite Database

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2022

Effect of dust on rainfall over the Red Sea coast based on WRF-Chem model simulations

Water is the single most important element of life. Rainfall plays an important role in the spatial and temporal distribution of this precious natural resource, and it has a direct impact on agricultural production, daily life activities, and human health. One of the important elements that govern rainfall formation and distribution is atmospheric aerosol, which also affects the Earth's radiation balance and climate. Therefore, understanding how dust compositions and distributions affect the regional rainfall pattern is crucial, particularly in regions with high atmospheric dust loads such as the Middle East. Although aerosol and rainfall research has garnered increasing attention as both an independent and interdisciplinary topic in the last few decades, the details of various direct and indirect pathways by which dust affects rainfall are not yet fully understood. Here, we explored the effects of dust on rainfall formation and distribution as well as the physical mechanisms that govern these phenomena, using high-resolution WRF-Chem simulations (~1.5 km × 1.5 km) configured with an advanced double-moment cloud microphysics scheme coupled with a sectional eight-bin aerosol scheme. Our model-simulated results were realistic, as evaluated from multiple perspectives including vertical profiles of aerosol concentrations, aerosol size distributions, vertical profiles of air temperature, diurnal wind cycles, and spatio-temporal rainfall patterns. Rainfall over the Red Sea coast is mainly caused by warm rain processes, which are typically confined within a height of ~6 km over the Sarawat mountains and exhibit a strong diurnal cycle that peaks in the evening at approximately 18:00 local time under the influence of sea breezes. Numerical experiments indicated that dust could both suppress or enhance rainfall. The effect of dust on rainfall was calculated as total, indirect, and direct effects, based on 10-year August-average daily-accumulated rainfall over the study domain covering the eastern Red Sea coast. For extreme rainfall events (domain-average daily-accumulated rainfall of ≥ 1.33 mm), the net effect of dust on rainfall was positive or enhancement (6.05 %), with the indirect effect (4.54 %) and direct effect (1.51 %) both causing rainfall increase. At a 5 % significance level, the total and indirect effects were statistically significant whereas the direct effect was not. For normal rainfall events (domain-average daily-accumulated rainfall < 1.33 mm), the indirect effect enhanced rainfall (4.76 %) whereas the direct effect suppressed rainfall (-5.78 %), resulting in a negative net suppressing effect (-1.02 %), all of which were statistically significant. We investigated the possible physical mechanisms of the effects and found that the rainfall suppression by dust direct effects was mainly caused by the scattering of solar radiation by dust. The surface cooling induced by dust weakens the sea breeze circulation, which decreases the associated landward moisture transport, ultimately suppressing rainfall. For extreme rainfall events, dust causes net rainfall enhancement through indirect effects as the high dust concentration facilitates raindrops to grow when the water vapor is sufficiently available. Our results have broader scientific and environmental implications. Specifically, although dust is considered a problem from an air quality perspective, our results highlight the important role of dust on sea breeze circulation and associated rainfall over the Red Sea coastal regions. Our results also have implications for cloud seeding and water resource management.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2024

Field Validation of Cloud Properties Sensor Field Campaign Report

The purpose of this campaign is to deploy Aerodyne Research Inc.’s extended wavelength cloud optical properties sensor (TWST-EN) in an operationally relevant environment with co-located, validated sensors. The Atmospheric Radiation Measurement (ARM) user facility’s Southern Great Plains (SGP) observatory is ideal for this deployment because of the variety of operational sensors that can measure some of the same cloud properties using different modalities. While cloud property sensors have long existed, they tend to be costly to produce and maintain. Our sensor measures absolute spectral radiance in the two bands and will retrieve cloud optical depth (COD), droplet effective radius, and thermodynamic phase. Our prototype is built predominantly from off-the-shelf components and uses uncooled spectrometers. A lower-cost, easy-to-use sensor such as this could allow deployment at many more sites for greater spatial coverage. Analysis and retrieval algorithm development using the data from this deployment has been a central technical objective of our U.S. Department of Energy Small Business Innovative Research (SBIR) Phase 2 contract (DE-SC0020473: Low-Cost Shortwave Spectroradiometer for Retrieval of Cloud Properties).

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2025

Detecting tropospheric composition and climate responses to US air pollution controls in the context of internally-arising variability

Since the 1970s, air pollutant emissions controls in the United States (US) have lowered concentrations of ozone (O 3 ) and aerosols, which have opposing radiative effects on surface temperature. Using a pair of initial-condition ensembles generated by a fully-coupled chemistry-climate model, we simulate the “world avoided” by US air pollution controls. In this counterfactual world, we find tropospheric column O 3 increases, robust to natural internal variability, extending across the Northern Hemisphere. Robust aerosol increases, dominated by sulfate, remain localized near the US. Wintertime Northwest Atlantic cloud droplet number concentration is particularly sensitive to US aerosol. While an ensemble mean US surface cooling signal (−0.4 °C) implies that aerosol-driven cooling prevails over any O 3 -induced warming, we find that large regional internal variability will confound its detection in any single transient realization. Larger signal-to-noise ratios for composition versus climate variables underscore the greater detectability of emissions-driven changes in tropospheric composition compared to their associated climate impacts.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2024

EPCAPE-PT-LANL Measurements: Single Particle Soot Photometer

Coastal cities offer a unique environment for studying aerosol-cloud interactions and the effects of urban emissions on cloud properties. As part of the Eastern Pacific Cloud Aerosol Precipitation Experiment (EPCAPE), the Partitioning Thrust by Los Alamos National Laboratory (EPCAPE-PT-LANL) was conducted. Our campaign focused on measuring the optical and chemical properties of aerosols and their interactions within marine stratocumulus clouds in La Jolla, California. EPCAPE-PT-LANL enhances the primary goals of EPCAPE through innovative observations of vapor-phase transitions between aerosols and cloud droplets, the impact of black carbon on aerosol-cloud dynamics, and the effects of cloud processing on aerosol optical properties. Instrument: Single Particle Soot Photometer (Droplet Measurements Technology) Data Notes: Contact us if you want additional data products from this instrument. Reported data is the black carbon (rBC) number and mass concentration with diagnostic flags. The SP2 measures incandescence from particles that is induced with a 1064 Nd-YAG laser. Particles that absorb the laser energy and then emit radiation is assumed to contain black carbon. The amount of intensity of radiation is related to the mass of absorbing material in the particle. Here, we calibrate the incandescence intensity to size selected Regal Black (Cabot) nebulized from solution. Data provided for the EPCAPE campaign used the combined broadband high-gain + low-gain channels (BHBL). Each channel has a lower threshold of detection equivalent to 2-s of the respective channel noise. Thresholding has been applied to select between the high-gain and low-gain channels. The detection limit is 80-540 nm (Deq) or 0.36- 55 fg. It is assumed that rBC is the only aerosol type that is in significant concentration in the sampled atmosphere that absorbs the laser energy. Particle data are integrated over 10 second windows to calculate a rBC number and mass concentration. QC/QA: • Diagnostic flags that impacted measured concentration: - Sample, Sheath, and Purge Flow Rates: Despite observing fluctuations in all flows, the rBC detection and mass quantification are generally observed to be stable, although large changes in sample flow rate did impact detection efficiency. A flag was implemented for sample flow deviations >12 cm3/min from the set point averaged over 30 seconds - Laser Power: Detection efficiency decreases with laser power and deviations in laser power also affect mass quantification. Flag for laser power is set for deviations in laser current from the set value >5 mA. - Primary Detector Threshold: Primary thresholding is the signal value which determines whether a “particle” is recorded. Thresholding errors occur when the threshold value is too HIGH and real particles are ignored. • Several periods without data: - 16-18 Nov: Ultra Zero Air generator failure, flows deviated significantly from set points. rBC # conc recovered but questionable. - 20-21 Nov: Offline for calibrations for several hours each day. - 25-27 Nov: Data is missing. - 30 Nov: Power outage 3 Dec: SP2 hard-drive full. - 3 Dec: Power Outage Header: - BHBL_NumbConc[#/cc]: Refers to the number concentration of refractory black carbon (rBC) measured from combined broadband high-gain and low-gain channels, expressed in particles per cubic centimeter. - BHBL_BCMass_Conc[ug/m3]: Refers to the mass concentration of refractory black carbon (rBC) measured from combined broadband high-gain and low-gain channels, expressed in micrograms per cubic meter. - NoData_Flag[bool]: A boolean flag that indicates whether no data was recorded during a measurement. - NoBC_Flag[bool]: A boolean flag indicating whether no black carbon particles were recorded during the measurement. - Laser_Flag[bool]: A boolean flag indicating deviations in laser current during the measurement. - SampleFlow_Flag[bool]: A boolean flag indicating deviations from the set sample flow rate during the measurement. - PrimThresh_Flag[bool]: A boolean flag indicating deviations from the set primary threshold during the measurement, potentially ignoring real particles. - Manual_Flag[bool]: A boolean flag indicating manual intervention or adjustments during the measurement. - CVI_Flag[bool]: A boolean flag indicating whether the Counterflow Virtual Impactor (CVI) was active or inactive during the measurement.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2023

Sensitivity of Arctic Surface Temperature to Including a Comprehensive Ocean Interior Reflectance to the Ocean Surface Albedo Within the Fully Coupled CESM2

Abstract Almost all current climate models simplify the ocean surface albedo (OSA) by assuming the reflected solar energy without the ocean interior contribution. In this study, an improved ocean surface albedo scheme is incorporated into the Community Earth System Model version 2 (CESM2) to assess the sensitivity of Arctic surface temperature to including ocean interior reflectance to the OSA. Fully coupled CESM2 simulations with and without ocean interior reflectance are subsequently performed, we focus on the analysis of Arctic surface temperature responses. Incorporating ocean interior reflectance increases absorbed solar radiation and warms the ocean, enhancing seasonal heat storage and release across the Arctic Ocean, and increasing sea ice reduction and positive climate feedbacks that elevates Arctic surface temperature. Seasonal variations in air‐surface temperature differences induce changes in turbulent heat flux patterns, concurrently modifying dynamic advection and moisture processes that affect boundary layer humidity and low clouds, especially in winter. Based on partitioning physical processes in the thermodynamic energy equation, surface air warming is induced primarily through positive heating anomalies of vertical advection, latent heat release, and longwave radiative forcing. Through an examination of the surface energy budget, skin temperature warming is driven predominantly by increased downward longwave radiation, positive surface albedo feedback in summer, and increased conductive heat transport from the ocean particularly in winter. Significant effects of ocean interior reflectance on the Arctic Ocean, including sea surface warming and sea ice reduction, justify the importance of ocean interior reflectance in climate models for better understanding of ongoing Arctic climate changes.

Meteorology & Atmospheric Sciences↗

DOE OSTI2024

Cloud Processing of Aerosol during SAIL Field Campaign Report

Globally, on average, the release rate of aerosols from clouds is estimated to be about 6,000 Tg/yr and an aerosol particle is estimated to experience about three cloud cycles. Cloud processing of aerosol produces aerosols that have dramatically different physicochemical properties compared to their original form. Cloud processing may transform particles to efficient cloud condensation nuclei (CCN) or ice nucleating particles (INP) that can further participate in cloud formation. We investigated cloud processing of aerosol during the U.S. Department of Energy (DOE)’s Atmospheric Radiation Measurement (ARM) Surface Atmosphere Integrated Field Laboratory (SAIL) field campaign using multi-modal offline analysis techniques available at DOE’s Environmental Molecular Sciences Laboratory (EMSL). The main scientific aim of this project was to understand the processes that transform aerosols (chemically, and physically), and influence aerosol-cloud interactions. Aerosol particles undergo significant modifications due to warm (cloud droplets) and cold cloud (ice crystals) processing. Cloud processing of aerosol has important effects on the atmospheric aerosol number and mass concentration, size distribution, phase separation, and chemical composition.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2023

The characteristics of atmospheric boundary layer height over the Arctic Ocean during MOSAiC

The important roles that the atmospheric boundary layer (ABL) plays in the central Arctic climate system have been recognized, but the atmospheric boundary layer height (ABLH), defined as the layer of continuous turbulence adjacent to the surface, has rarely been investigated. Using a year-round radiosonde dataset during the Multidisciplinary drifting Observatory for the Study of Arctic Climate (MOSAiC) expedition, we improve a Richardson-number-based algorithm that takes cloud effects into consideration and subsequently analyze the characteristics and variability of the ABLH over the Arctic Ocean. The results reveal that the annual cycle is clearly characterized by a distinct peak in May and two respective minima in January and July. This annual variation in the ABLH is primarily controlled by the evolution of the ABL thermal structure. Temperature inversions in the winter and summer are intensified by seasonal radiative cooling and warm-air advection with the surface temperature constrained by melting, respectively, leading to the low ABLH at these times. Meteorological and turbulence variables also play a significant role in ABLH variation, including the near-surface potential temperature gradient, friction velocity, and turbulent kinetic energy (TKE) dissipation rate. In addition, the MOSAiC ABLH is more suppressed than the ABLH during the Surface Heat Budget of the Arctic Ocean (SHEBA) experiment in the summer, which indicates that there is large variability in the Arctic ABL structure during the summer melting season.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2026

Automation of Nanoparticle Synthesis Processes in a Plasma Environment Using LabVIEW

This work presents an automated control system for the synthesis of nanomaterials by plasma-enhanced chemical vapor deposition (PECVD), implemented using the LabVIEW software environment. The main objective of the study is to develop an integrated hardware-software platform that enables sequential control of the key stages of the PECVD process, including vacuum chamber preparation, pressure monitoring, working gas supply, plasma ignition, power matching, cyclic nanomaterial growth, and optical monitoring of nanoparticles in the plasma environment. The use of LabVIEW made it possible to integrate actuator control, experimental parameter acquisition, and realtime process visualization within a single automated system. The automated cycle begins with evacuation of the reaction chamber to a predefined base pressure. Transition to the next stage is permitted only after the specified pressure threshold has been reached, ensuring reproducible initial conditions for each experiment. The program then controls the supply of the working gas through mass flow controllers (MFCs). In this work, two gas-flow control modes were considered: analog control using a 0-5 V voltage signal and digital communication via RS-232 interface. It was shown that the analog approach requires accurate scaling of the control voltage, since applying 5 V corresponds to full-scale opening of the controller and results in the maximum gas flow. In contrast, the RS232 interface enables the gas flow rate to be specified directly in sccm, improving the accuracy, flexibility, and convenience of gas-environment control. After pressure stabilization, LabVIEW initiates RF plasma ignition and executes the RF matching algorithm aimed at minimizing reflected power and improving the stability of the plasma process. A separate software module implements the cyclic nanomaterial growth mode, in which the plasma-on time, plasma duration, and total number of synthesis cycles are predefined. This approach makes it possible to control material accumulation on the substrate and to correlate the process parameters with the morphological characteristics of the resulting nanostructures. The final module of the system is designed for optical monitoring of the nanoparticle cloud density in dusty plasma. For this purpose, the change in the intensity of laser radiation passing through the plasma region is recorded using a photodetector and a Keithley 2401 measuring unit connected to LabVIEW via RS-232 interface. The difference between the initial and modified optical signal intensity is used as a diagnostic parameter characterizing the formation and temporal evolution of nanoparticles. The developed system demonstrates that LabVIEW can be effectively applied not only for the automation of individual instruments, but also for the implementation of a complete digital control cycle for PECVD-based nanomaterial synthesis.

PECVD↗

DOE OSTI2021

Retrieving microphysical properties of concurrent pristine ice and snow using polarimetric radar observations

Abstract. Ice and mixed-phase clouds play a key role in our climate system because of their strong controls on global precipitation and radiation budget. Their microphysical properties have been characterized commonly by polarimetric radar measurements. However, there remains a lack of robust estimates of microphysical properties of concurrent pristine ice and aggregates because larger snow aggregates often dominate the radar signal and mask contributions of smaller pristine ice crystals. This paper presents a new method that separates the scattering signals of pristine ice embedded in snow aggregates in scanning polarimetric radar observations and retrieves their respective abundances and sizes for the first time. This method, dubbed ENCORE-ice, is built on an iterative stochastic ensemble retrieval framework. It provides the number concentration, ice water content, and effective mean diameter of pristine ice and snow aggregates with uncertainty estimates. Evaluations against synthetic observations show that the overall retrieval biases in the combined total microphysical properties are within 5 % and that the errors with respect to the truth are well within the retrieval uncertainty. The partitioning between pristine ice and snow aggregates also agrees well with the truth. Additional evaluations against in situ cloud probe measurements from a recent campaign for a stratiform cloud system are promising. Our median retrievals have a bias of 98 % in the total ice number concentration and 44 % in the total ice water content. This performance is generally better than the retrieval from empirical relationships. The ability to separate signals of different ice species and to provide their quantitative microphysical properties will open up many research opportunities, such as secondary ice production studies and model evaluations for ice microphysical processes.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2022

Effective radiative forcing of anthropogenic aerosols in E3SMv1: historical changes, causality, decomposition, and parameterization sensitivities

The effective radiative forcing of anthropogenic aerosols (ERF aer ) is an important measure of the anthropogenic aerosol effects simulated by a global climate model. Here we analyze ERF aer simulated by the E3SMv1 atmosphere model using both century-long free-running atmosphere-land simulations and short nudged simulations. We relate the simulated ERF aer to characteristics of the aerosol composition and optical properties, and evaluate the relationships between key aerosol and cloud properties. In terms of historical changes from the year 1870 to 2014, our results show that the global mean anthropogenic aerosol burden and optical depth increase during the simulation period as expected, but the regional averages show large differences in the temporal evolution. The largest regional differences are found in the emission-induced evolution of the burden and optical depth of the sulfate aerosol: a strong decreasing trend is seen in the Northern Hemisphere high-latitude region after around 1970, while a continued increase is simulated in the tropics. Consequently, although the global mean anthropogenic aerosol burden and optical depth increase from 1870 to 2014, the ERF aer magnitude does not increase after around year 1970. The relationships between key aerosol and cloud properties (relative changes between preindustrial and present-day conditions) also show evident changes after 1970, diverging from the linear relationships exhibited for the period from 1870 to 2014. The ERF aer in E3SMv1 is relatively large compared to the recently published multi-model estimates; the primary reason is the large indirect aerosol effect (i.e., through aerosol-cloud interactions). Compared to other models, E3SMv1 features a stronger sensitivity of the cloud droplet effective radius to changes in the cloud droplet number concentration. Large sensitivity is also seen in the liquid cloud optical depth, which is determined by changes in both the effective radius and liquid water path. Aerosol-induced changes in liquid and ice cloud properties in E3SMv1 are found to have a strong correlation, as the evolution of anthropogenic sulfate aerosols affects both the liquid cloud formation and the homogeneous ice nucleation in cirrus clouds. The ERF aer estimates in E3SMv1 for the shortwave and longwave components are sensitive to the parameterization changes in both liquid and ice cloud processes. When the parameterization of ice cloud processes is modified, the top-of-atmosphere forcing changes in the shortwave and longwave components largely offset each other, so the net effect is negligible. This suggests that, to reduce the magnitude of the net ERF aer , it would be more effective to reduce the anthropogenic aerosol effect through liquid or mixed-phase clouds.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2022

Effective radiative forcing of anthropogenic aerosols in E3SM version 1: historical changes, causality, decomposition, and parameterization sensitivities

Abstract. The effective radiative forcing of anthropogenic aerosols (ERFaer) is an important measure of the anthropogenic aerosol effects simulated by a global climate model. Here we analyze ERFaer simulated by the E3SM version 1 (E3SMv1) atmospheric model using both century-long free-running atmosphere–land simulations and short nudged simulations. We relate the simulated ERFaer to characteristics of the aerosol composition and optical properties, and we evaluate the relationships between key aerosol and cloud properties. In terms of historical changes from the year 1870 to 2014, our results show that the global mean anthropogenic aerosol burden and optical depth increase during the simulation period as expected, but the regional averages show large differences in the temporal evolution. The largest regional differences are found in the emission-induced evolution of the burden and optical depth of the sulfate aerosol: a strong decreasing trend is seen in the Northern Hemisphere high-latitude region after around 1970, while a continued increase is simulated in the tropics. The relationships between key aerosol and cloud properties (relative changes between pre-industrial and present-day conditions) also show evident changes after 1970, diverging from the linear relationships exhibited for the period of 1870–1969. In addition to the regional differences in the simulated relationships, a reduced sensitivity in cloud droplet number and other cloud properties to aerosol perturbations is seen when the aerosol perturbation is large. Consequently, the global annual mean ERFaer magnitude does not increase after around 1970. The ERFaer in E3SMv1 is relatively large compared to the recently published multi-model estimates; the primary reason is the large indirect aerosol effect (i.e., through aerosol–cloud interactions). Compared to other models, E3SMv1 features large relative changes in the cloud droplet effective radius in response to aerosol perturbations. Large sensitivity is also seen in the liquid cloud optical depth, which is determined by changes in both the effective radius and liquid water path. Aerosol-induced changes in liquid and ice cloud properties in E3SMv1 are found to have a strong correlation, as the evolution of anthropogenic sulfate aerosols affects both the liquid cloud formation and the homogeneous ice nucleation in cirrus clouds (that causes a large effect on longwave ERFaer). As suggested by a previous study, the large ERFaer appears to be one of the reasons why the model cannot reproduce the observed global mean temperature evolution in the second half of the 20th century. Sensitivity simulations are performed to understand which parameterization and/or parameter changes have a large impact on the simulated ERFaer. The ERFaer estimates in E3SMv1 for the shortwave and longwave components are sensitive to the parameterization changes in both liquid and ice cloud processes. When the parameterization of ice cloud processes is modified, the top-of-model forcing changes in the shortwave and longwave components largely offset each other, so the net effect is negligible. This suggests that, to reduce the magnitude of the net ERFaer, it would be more effective to reduce the anthropogenic aerosol effect through liquid or mixed-phase clouds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗