Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “cathode utilization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Improvement of Li-S battery electrochemical performance with 2D TiS 2 additive

As a multifunctional cathode additive, TiS 2 has been used in Li-S batteries to promote sulfur utilization and improve cell cycle life. The improvement of Li-S cell electrochemical performance in the presence of TiS 2 has been attributed to the ability of TiS 2 in adsorbing polysulfide. To maximize the interaction between polysulfides and TiS 2 , the 2-dimensional (2D) TiS 2 nano-sheets with highly exposed TiS 2 surface area has been successfully synthesized by a two-step sonication synthetic procedure. The 2D TiS 2 particles are micron size in the basal plane direction and are nano-sized along the c-axis direction. 2D TiS 2 nano-sheets may adsorb polysulfides more effectively than the raw TiS 2 powder. Li-S cells with 2D TiS 2 nano-sheets additive exhibit better discharge rate capability and significantly reduced capacity-fading after a long term cell cycling. Here, this improvement can be partially attributed to the uniform distribution of 2D TiS 2 nano-sheets particles within the sulfur cathode matrix, which induces more uniform sulfur and lithium sulfide deposition during the cell charge and discharge.

2D TiS2 nano-sheets↗

Li2O-Based Cathode Additives Enabling Prelithiation of Si Anodes

Low first-cycle Coulombic efficiency is especially poor for silicon (Si)-based anodes due to the high surface area of the Si-active material and extensive electrolyte decomposition during the initial cycles forming the solid electrolyte interphase (SEI). Therefore, developing successful prelithiation methods will greatly benefit the development of lithium-ion batteries (LiBs) utilizing Si anodes. In pursuit of this goal, in this study, lithium oxide (Li2O) was added to a LiNi0.6Mn0.2Co0.2O2 (NMC622) cathode using a scalable ball-milling approach to compensate for the initial Li loss at the anode. Different milling conditions were tested to evaluate the impact of particle morphology on the additive performance. In addition, Co3O4, a well-known oxygen evolution reaction catalyst, was introduced to facilitate the activation of Li2O. The Li2O + Co3O4 additives successfully delivered an additional capacity of 1116 mAh/gLi2O when charged up to 4.3 V in half cells and 1035 mAh/gLi2O when charged up to 4.1 V in full cells using Si anodes.

25 ENERGY STORAGE↗

Accelerating Laboratory-Based, All-Solid-State Battery Research and Development: Industrially Relevant Small-Batch Dry-Processing, Small and Low-Cost Test Fixtures, and Short-Tolerant Separators

This work presents improvements to mixing (for dry-processed electrodes), separator robustness, and cell testing jigs for all-solid-state batteries (ASSBs). These developments combine synergistically to enable rapid research and development of ASSB catholytes. A mechanical "kneader" is designed and built which emulates the mixing and fibrillation of poly-tetrafluoroethylene binder that occurs in industrially relevant twin-screw extruders. A modest improvement in the mixing and dispersion catholyte materials is observed using micro-resolution X-ray computed tomography (X-ray CT). Catholytes are paired with an In-metal anode and separated by a novel, dual-layer, polyaramid-fiber-supported, sulfide-solid electrolyte (Li6 PS5 Cl) separator. This separator achieves high short tolerance which enabled a 95% success rate across 20 attempted cells and to date over 100 successful cells have been built. ASSBs were tested in a 2032 coin-cell format. Simultaneous cycling of a large number of cells is further enabled by a compact and low cost (~ 38 USD per jig) pressure application jig of which 100 have been constructed to date. The utility of these advances is demonstrated through a brief study on the effect cathode-side conductive carbon and current collector type has on capacity and rate performance.

25 ENERGY STORAGE↗

Mesoscale Effective Property Simulations Incorporating Conductive Binder

Lithium-ion battery electrodes are composed of active material particles, binder, and conductive additives that form an electrolyte-filled porous particle composite. The mesoscale (particle-scale) interplay of electrochemistry, mechanical deformation, and transport through this tortuous multi-component network dictates the performance of a battery at the cell-level. Effective electrode properties connect mesoscale phenomena with computationally feasible battery-scale simulations. We utilize published tomography data to reconstruct a large subsection (1000+ particles) of an NMC333 cathode into a computational mesh and extract electrode-scale effective properties from finite element continuum-scale simulations. We present a novel method to preferentially place a composite binder phase throughout the mesostructure, a necessary approach due difficulty distinguishing between non-active phases in tomographic data. We compare stress generation and effective thermal, electrical, and ionic conductivities across several binder placement approaches. Isotropic lithiation-dependent mechanical swelling of the NMC particles and the consideration of strain-dependent composite binder conductivity significantly impact the resulting effective property trends and stresses generated. Lastly, our results suggest that composite binder location significantly affects mesoscale behavior, indicating that a binder coating on active particles is not sufficient and that more accurate approaches should be used when calculating effective properties that will inform battery-scale models in this inherently multi-scale battery simulation challenge.

25 ENERGY STORAGE↗

Theoretical and Experimental Studies in Accelerator Physics

This report describes research supported by the US Dept. of Energy Office of High Energy Physics (OHEP), performed by the UCLA Particle Beam Physics Laboratory (PBPL). The UCLA PBPL has, over the last two decades-plus, played a critical role in the development of advanced accelerators, fundamental beam physics, and new applications enabled by these thrusts, such as new types of accelerator-based light sources. As the PBPL mission is broad it is natural that it has been grown within the context of the accelerator science and technology stewardship of the OHEP. Indeed, steady OHEP support for the program has always been central to the success of the PBPL; it has provided stability, and above all has set the over-arching themes for our research directions, which have producing over 500 publications (>120 in high level journals). While other agency support has grown notably in recent years, permitting more vigorous pursuit of the program, it is transient by comparison. Beyond permitting program growth in a time of flat OHEP budgets, the influence of other agency missions is found in push to adapt advanced accelerator methods to applications, in light of the success the field has had in proof-of-principle experiments supported first by the DoE OHEP. This three-pronged PBPL program — advanced accelerators, fundamental beam physics and technology, and revolutionary applications — has produced a generation of students that have had a profound affect on the US accelerator physics community. PBPL graduates, numbering 28 in total, form a significant population group in the accelerator community, playing key roles as university faculty, scientific leaders in national labs (two have been named Panofsky Fellows at SLAC), and vigorous proponents of industrial application of accelerators. Indeed, the development of advanced RF, optical and magnet technology at the PBPL has led directly to the spin-off company, RadiaBeam Technologies, now a leading industrial accelerator firm. We note also that PBPL graduates remain as close elaborators for the program after leaving UCLA. The UCLA PBPL program is a foremost developer of on-campus facilities, such as the Neptune and Pegasus Laboratories, providing a uniquely strong environment for student-based research. In addition, the PBPL is a strong user of off-campus national lab facilities, such as SLAC FACET and NLCTA, and the BNL ATF. UCLA has also vigorously participated in the development of these facilities. The dual emphases on off- and on-campus opportunities permit the PBPL to address in an agile way a wide selection of cutting-edge research topics. The topics embraced by this proposal illustrate this program aspect well. These include: GV/m dielectric wakefield acceleration/coherent Cerenkov radiation experiments at FACET (E-201) and the ATF; synergistic laser-excited dielectric accelerator and light source development; plasma wakefield (PWFA) experiments on “Trojan horse” ionization injection (FACET E-210), quasi-nonlinear PWFA at BNL and the production at Neptune high transformer ratio plasma wakes; the inauguration of a new type of RF photoinjector termed “hybrid” at UCLA, and application to PWFA; space-charge dominated beam and cathode/near cathode physics; the study of advanced IFEL systems, for very high energy gain and utilization of novel OAM modes; the physcis of inverse Compton scattering (ICS), with applications to e+ production and γγ colliders; electron diffraction; and advanced beam diagnostics using coherent imaging techniques. These subjects are addressed under the leadership of PBPL director Prof. James Rosenzweig in Task A, and Prof. Pietro Musumeci in Task J, which was initiated following his OHEP Outstanding Junior Investigator award.

43 PARTICLE ACCELERATORS↗

Phloroglucinol–2,6‐Diaminoanthraquinone as a Durable Redox Mediator for Enhancing Conversion Reaction Kinetics in Lithium‐Sulfur Batteries

Abstract Lithium‐sulfur batteries, despite being a promising solution for next‐generation secondary batteries, require substantial efforts to overcome the challenges of sluggish sulfur redox kinetics, polysulfides shuttling, and Li metal instability before achieving practical viability. Conventional strategies that utilize metal catalysts or soluble redox mediators (RMs) are limited by either impractical producing processes or unsatisfactory service life. Herein, an electrochemically active organic material, phloroglucinol – 2,6‐diaminoanthraquinone (PG‐DAAQ) is synthesized through a green and facile polymerization process to better resolve these issues. Serving as an RM at the cathode, PG‐DAAQ exhibits enduring redox activity within the sulfur operating potential window, leading to enhanced redox kinetics and sulfur utilization. Remarkably, even without any metal elements, PG‐DAAQ exhibits an excellent affinity to polysulfides, thereby suppressing the shuttling and facilitating the formation of a more favorable solid‐electrolyte interface to stabilize Li deposition at the anode. As a result, Li‐S cells employing PG‐DAAQ show significantly enhanced cycling and rate performances than the control cells. Even with a low electrolyte‐to‐sulfur ratio of 6, pouch cells with PG‐DAAQ deliver a reversible discharge capacity of 821 mA h g −1 after 100 cycles at a C/10 rate.

Lai, Tianxing↗

Core-Protected Platinum Monolayer Shell High-Stability Electrocatalysts for Fuel-Cell Cathodes

Platinum monolayers can act as shells for palladium nanoparticles to lead to electrocatalysts with high activities and an ultralow platinum content, but high platinum utilization. The stability derives from the core protecting the shell from dissolution. In fuel-cell tests, no loss of platinum was observed in 200,000 potential cycles, whereas loss of palladium was significant.

30 DIRECT ENERGY CONVERSION↗

Quantifying the electrochemical active site density of precious metal-free catalysts in situ in fuel cells

We report advances in the development of precious-group metal-free (PGM-free) catalysts for the oxygen reduction reaction (ORR) in fuel cell cathodes have produced active catalysts that reduce the performance gap to the incumbent Pt-based materials. However, utilization of state-of-the-art PGM-free catalysts for commercial applications is currently impeded by their relatively low durability. Methods designed to study catalyst degradation in the operation of fuel cells are therefore critical for understanding durability issues and, ultimately, their solutions. Here we report the use of Fourier-transform alternating current voltammetry as an electrochemical method for accurate quantification of the electrochemically active site density of PGM-free cathode catalysts, and to follow their degradation in situ during the operation of polymer electrolyte fuel cells. Using this method, we were able to quantify the electrochemical active site density, which will enable the elucidation of degradation mechanisms of PGM-free ORR catalysts in situ in fuel cells.

25 ENERGY STORAGE↗

A Dual–Phase Electrolyte for High–Energy Lithium–Sulfur Batteries

Dissolution of lithium polysulfides (LiPSs) is essential for fast cathode kinetics, but detrimental for anode stability, especially under lean electrolyte conditions. Here in this work, the phase separation phenomenon between solvents with different polarities (tetramethyl sulfone [TMS] and dibutyl ether [DBE]) is utilized to enable the design of a dual-phase electrolyte. High-polarity, high-density TMS–lithium bis(trifluoromethanesulfonyl)imide–ammonium trifluoroacetate as the cathode electrolyte strongly solvates LiPSs, which propel the sulfur redox reaction. Moreover, the composite of DBE and a polymeric ion conductor serves as the anode electrolyte. The addition of DBE in the anode side effectively prevents the crossover of corrosive species (LiPSs and ammonia trifluoroacetate), enabling a significant improvement in Li-metal anode stability. The electrode-specific dual-phase electrolyte design provides electrochemical performance superior to conventional electrolytes. Without additional electrode engineering, pouch cells assemble with the dual-phase electrolyte cycle under a lean electrolyte (4 µL mg –1 ) and low-Li-excess condition (N/P = 3) for 120 cycles.

25 ENERGY STORAGE↗

Photoelectrochemical Carbon Dioxide Reduction Using a Nanoporous Ag Cathode

Solar fuel production from abundant sources using photoelectrochemical (PEC) systems is an attractive approach to address the challenges associated with the intermittence of solar energy. In comparison to electrochemical systems, PEC cells directly utilize solar energy as the energy input, and if necessary, then an additional external bias can be applied to drive the desired reaction. In this work, a PEC cell composing of a Ni-coated Si photoanode and a nanoporous Ag cathode was developed for CO 2 conversion to CO. We report the thin Ni layer not only protected the Si wafer from photocorrosion but also served as the oxygen evolution catalyst. At an external bias of 2.0 V, the PEC cell delivered a current density of 10 mA cm –2 with a CO Faradaic efficiency of ~70%. More importantly, a stable performance up to 3 h was achieved under photoelectrolysis conditions, which is among the best literature-reported performances for PEC CO 2 reduction cells. The photovoltage of the PEC cell was estimated to be ~0.4 V, which corresponded to a 17% energy saving by solar energy utilization. Postreaction structural analysis showed the corrosion of the Ni layer at the Si photoanode/catalyst interface, which caused performance degradation under prolonged operations. A stable oxygen evolution catalyst with a robust interface is crucial to the long-term stability of PEC CO 2 reduction cells.

25 ENERGY STORAGE↗

Fluidized Bed Production of Surface Functionalized Powders for Solid Oxide Fuel Cell Cathodes

Fuel cells offer tremendous potential for highly efficient conversion of fossil fuels to useable electrical power. Solid oxide fuel cells (SOFC) are particularly attractive, due to their high efficiency and capability to utilize either hydrogen or hydrocarbon fuels. Presently, there is considerable incentive to develop medium temperature (600 C to 800 C) SOFC's, in order to reduce the material compatibility issues and the engineering challenges associated with higher operating temperatures. Developing cathode materials with viable performance at intermediate temperatures is presently one of the key challenges in commercialization of solid oxide fuel cells. Recent works have shown the advantages of using surface functionalized cathode materials to improve SOFC performance at intermediate temperatures. However, present techniques for surface functionalization are expensive and difficult to implement in commercial SOFC production. In this SBIR Program, Structured Materials Industries, Inc. (SMI), along with partners FuelCell Energy, Inc. (FCE) and the University of Connecticut (UConn), demonstrated a simple and economical process to produce surface functionalized cathode materials, based on fluidized bed technology. SMI has developed a variation on this technology, known as Fluidized Bed Chemical Vapor Deposition (FBCVD), and is presently implementing and commercializing FBCVD as an economical and scalable process to deposit coatings on powder materials. In Phase I of this Project, the SBIR team demonstrated technical feasibility of this approach for producing high performance SOFC cathode materials. In this Phase II Project, the SBIR team refined and optimized the FBCVD process and the surface functionalized cathode materials. Surface functionalized powders of various composition and morphology were produced at SMI using the FBCVD process. Electrochemical characterization of the powders was done at FCE under actual SOFC operating conditions. The results demonstrated the potential for significant improvement in SOFC performance. Long term testing at FCE showed the performance enhancement to be stable with time. Advanced materials characterization at UConn identified the composition and morphology of the materials. SMI's FBCVD processed materials represent a "drop in" replacement for present cathode materials, and should have minimal impact on SOFC production costs. SMI has designed a scaled up FBCVD system for high volume production of SOFC cathode materials, and is well positioned for future implementation and commercialization of the technology developed in this SBIR.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Surface Studies of High Voltage Lithium Rich Composition: Li1.2Mn0.525Ni0.175Co0.1O2

This article reports the evidence of surface film formation because of the breakdown of electrolyte upon high voltage cycling (4.9 V) of lithium rich cathode having a nominal composition of, Li1.2Mn0.525Ni0.175Co0.1O2. We studied the chemical composition of this passivation film using electrochemical impedance, X-ray Photoelectron and micro-Raman spectroscopy and the results were compared against the pristine electrode. In order to distinguish the changes in the surface films composition induced by prolonged electrochemical cycling versus chemical passivation effect, we also studied the surface composition of cathode powders aged with electrolytes at 60 oC. Our study shows that electrodes cycled beyond 150 cycles showed a rapid drop in capacity due to increase in the surface film resistance resulting in limited capacity utilization.

36 MATERIALS SCIENCE↗

Nanoalloy catalysts inside fuel cells: An atomic-level perspective on the functionality by combined in operando x-ray spectroscopy and total scattering

We introduce an experimental approach for structural characterization of catalysts for fuel cells combining synchrotron x-ray spectroscopy and total scattering. The approach allows probing catalysts inside operating fuel cells with atomic-level precision (~ 0.02 Å) and element specificity (~ 2–3 at%) in both time (~ 1 min) and space (~ μm) resolved manner. The approach is demonstrated on exemplary Pd-Sn and Pt-Ni-Cu nanoalloy catalysts for the oxygen reduction reaction (ORR) deposited on the cathode of an operating proton exchange membrane fuel cell. In operando x-ray data show that under operating conditions, the catalyst particles can undergo specific structural changes, ranging from sub-Å atomic fluctuations and sharp nanophase transitions to a gradual strain relaxation and growth, which inflict significant losses in their ORR activity. Though triggered electrochemically, the changes are not driven solely by differences in the reduction potential and surface energy of the metallic species constituting the nanoalloys but also by the formation energy of competing nanophases, mismatch between the size of individual atomic species and their ability to interdiffuse fast in search of energetically favorable configurations. Given their complexity, the changes are difficult to predict and so the resulting ORR losses remain difficult to limit. We show that in operando knowledge of the structural evolution of nanoalloy catalysts helps create strategies for improving their activity and stability. In particular, we show that shaping Pd-Sn nanoalloys rich in Pd as cubes reduces the interdiffusion of atoms at their surface and so makes them better catalysts for ORR in fuel cells in comparison to other Pd-Sn nanoalloys. In addition, we demonstrate that the approach introduced here can provide knowledge of other major factors affecting the performance of fuel cells such as operating temperature and the overall catalyst utilization, in particular the evolution of elemental and mass distribution of catalyst particles over the cells’ cathode. Last but not least, we discuss how in operando x-ray spectroscopy and total x-ray scattering can bridge the knowledge gap between the widely used in situ SAXS, EXAFS and monocrystal surface XRD techniques for structural characterization of nanoalloy catalysts explored for energy related applications.

25 ENERGY STORAGE↗

Understanding extraction limits of plasma cathodes with experiment and simulation

The project is focused on computations for enhanced ionization near the exit orifice of a plasma cathode and how the cathode extraction electrode geometry and stray magnetic field structure influence available extractable current. The computational effort will take place at the Princeton Collaborative Research Laboratory (PCRF). The specific modeling platform to be utilized from PCRF is the electrostatic direct implicit particle in cell (EDIPIC) code. EDIPIC will be used to study ionization processes in the electron extraction region of the cathode. The control of electron energy is a key aspect to minimizing power losses in the plasma. Exiting electrons ionize gas leaving the orifice and in the process produce the dense plasma from which large amounts of current can be extracted. Project activities include studying processes that determine the energy distribution of the exiting electrons thus providing insight into how to optimize the source. The model will be validated and developed using experimental measurements as warranted. The familiarity and expertise of the team at PPPL with this type of plasma and the challenges posed greatly enhances the likelihood of gaining insight into the extraction sheath under the duration of the proposed activity. The effort is expected to shed a great deal of insight into electron extraction processes and pathways for optimization.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Sr 2 Fe 1.5 Mo 0.5 O 6-δ as a regenerative anode for solid oxide fuel cells

Sr 2 Fe 1.5 Mo 0.5 O 6-δ (SFM) was prepared using a microwave-assisted combustion synthesis method. Rietveld refinement of powder X-ray diffraction data reveals that SFM crystallizes in the simple cubic perovskite structure with iron and molybdenum disordered on the B-site. No structure transition was observed by variable temperature powder X-ray diffraction measurements in the temperature range of 25–800 °C. XPS results show that the iron and molybdenum valences change with an increase in temperature, where the mixed oxidation states of both iron and molybdenum are believed to be responsible for the increase in the electrical conductivity with increasing temperature. SFM exhibits excellent redox stability and has been used as both anode and cathode for solid oxide fuel cells. Presence of sulfur species in the fuel or direct utilization of hydrocarbon fuel can result in loss of activity, however, as shown in this paper, the anode performance can be regenerated from sulfur poisoning or coking by treating the anode in an oxidizing atmosphere. Thus, SFM can be used as a regenerating anode for direct oxidation of sulfur-containing hydrocarbon fuels.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Magnesium Battery Electrolytes with Improved Oxidative Stability Enabled by Selective Solvation in Fluorinated Solvents

Practical Mg batteries require electrolytes that are stable both toward reduction by Mg metal and oxidation by high voltage cathodes. State-of-the-art Mg electrolytes based on weakly-coordinating Mg salts utilize standard ether-type solvents (usually glymes) due to their reductive stability. However, the oxidative stabilities of these solvents are less than ideal, leading to difficulties in realizing the high oxidative stabilities of novel salts. On the other hand, alternative solvents with greater oxidative stability are typically unable to support Mg cycling. Here, in this work, we report a selective solvation approach involving the combination of glyme and hydrofluoroether solvents. Selective solvation of Mg 2+ by the glyme solvent component increases the oxidative stability of the glyme while maintaining sufficient reductive stability of the noncoordinating hydrofluoroether. We show that this approach enables the design of electrolytes with greater oxidative stability than glyme-only electrolytes while retaining enough reductive stability to cycle Mg metal. We also relate the influence of various coordination interactions among the solvents and anions with Mg 2+ to their electrochemical stabilities to better inform the design of future electrolytes.

25 ENERGY STORAGE↗

Dopant-tuned stabilization of intermediates promotes electrosynthesis of valuable C3 products

The upgrading of CO 2 /CO feedstocks to higher-value chemicals via energy-efficient electrochemical processes enables carbon utilization and renewable energy storage. Substantial progress has been made to improve performance at the cathodic side; whereas less progress has been made on improving anodic electro-oxidation reactions to generate value. Here we report the efficient electroproduction of value-added multi-carbon dimethyl carbonate (DMC) from CO and methanol via oxidative carbonylation. We find that, compared to pure palladium controls, boron-doped palladium (Pd-B) tunes the binding strength of intermediates along this reaction pathway and favors DMC formation. We implement this doping strategy and report the selective electrosynthesis of DMC experimentally. We achieve a DMC Faradaic efficiency of 83 ± 5%, fully a 3x increase in performance compared to the corresponding pure Pd electrocatalyst.

42 ENGINEERING↗

Advanced Intermediate-Temperature Na-S Battery

In this study, we reported an intermediate-temperature (~150°C) sodium-sulfur (Na-S) battery. With a reduced operating temperature, this novel battery can potentially reduce the cost and safety issues associated with the conventional high-temperature (300~350°C) Na-S battery. A dense β"-Al 2 O 3 solid membrane and tetraglyme were utilized as the electrolyte separator and catholyte solvent in this battery. Solubility tests indicated that cathode mixture of Na 2 S 4 and S exhibited extremely high solubility in tetraglyme (e.g., > 4.1 M for Na 2 S 4 + 4 S). CV scans of Na 2 S 4 in tetraglyme revealed two pairs of redox couples with peaks at around 2.22 and 1.75 V, corresponding to the redox reactions of polysulfide species. The discharge/charge profiles of the Na-S battery showed a slope region and a plateau, indicating multiple steps and cell reactions. In-situ Raman measurements during battery operation suggested that polysulfide species were formed in the sequence of Na 2 S 5 + S → Na 2 S 5 + Na 2 S 4 → Na 2 S 4 + Na 2 S 2 during discharge and in a reverse order during charge. This battery showed dramatic improvement in rate capacity and cycling stability over room-temperature Na-S batteries, which makes it attractive for renewable energy integration and other grid related applications.

25 ENERGY STORAGE↗