SEARCH · Engineering Papers

Results for “brittle fracture”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

All sources NASA NTRS DOE OSTI

NASA NTRS1985

Influence of voids on the strength of wrought materials

Three-dimensional voids, which are present in most materials, may be satisfactorily modelled by two-dimensional holes (i.e., cylindrical voids) in sheet metal. In this study, the influence of certain orientations and shapes of voids upon the mechanical properties and fracture behavior of certain ductile materials has been studied. The presence of voids is found to exert a negligible influence on the ultimate tensile strength, owing to plastic flow neutralizing the stress intensification present before yielding occurs. The shape and orientation of the defects, however, are seen to play an important role relative to strain at fracture. The maximum intensified tensile stress criterion which holds for brittle materials is found to apply to ductile materials as well.

Shaw, M. C.↗

NASA NTRS1987

Mechanical strength and tribological behavior of ion-beam deposited boron nitride films on non-metallic substrates

An investigation was conducted to examine the mechanical strength and tribological properties of boron nitride (BN) films ion-beam deposited on silicon (Si), fused silica (SiO2), gallium arsenide (GaAs), and indium phosphide (InP) substrates in sliding contact with a diamond pin under a load. The results of the investigation indicate that BN films on nonmetallic substrates, like metal films on metallic substrates, deform elastically and plastically in the interfacial region when in contact with a diamond pin. However, unlike metal films and substrates, BN films on nonmetallic substrates can fracture when they are critically loaded. Not only does the yield pressure (hardness) of Si and SiO2 substrates increase by a factor of 2 in the presence of a BN film, but the critical load needed to fracture increases as well. The presence of films on the brittle substrates can arrest crack formation. The BN film reduces adhesion and friction in the sliding contact. BN adheres to Si and SiO2 and forms a good quality film, while it adheres poorly to GaAs and InP. The interfacial adhesive strengths were 1 GPa for a BN film on Si and appreciably higher than 1 GPa for a BN film on SiO2.

Miyoshi, Kazuhisa↗

NASA NTRS1987

Mechanical strength and tribological behavior of ion-beam-deposited boron nitride films on non-metallic substrates

Miyoshi, Kazuhisa↗

NASA NTRS1994

Shoemaker-Levy 9 and the tidal disruption of comets

The break-up of Periodic Comet Shoemaker-Levy 9 into multiple pieces following its grazing encounter with Jupiter in July 1992 can be used to study tidally-induced fracture in comets. This spectacular event allows us not only to set limits on the size, strength and density of Shoemaker-Levy 9 itself, but provides invaluable guidance to numerical modeling of such encounters. In an extensive treatment of tidal breakup which assumed self-gravitating, homogeneous, perfectly elastic bodies, Dobrovolskis derived simple analytical expressions for the tidally-induced surface and central stresses. Both can be cast in such a way that Poisson's ratio is the only material dependent constant entering these expressions. Whether both surface and central failure must be initiated as a criterion for breakup, or either one of them is sufficient, remains a subject of disagreement. To resolve this debate, we model the details of cometary breakup using a three-dimensional Smooth Particle Hydrodynamics (SPH) code modified to simulate fracture in small solid objects. At lower stresses associated with brittle failure, we use a rate-dependent strength based on the nucleation of incipient flaws whose number density is given by a Weibull distribution.

Benz, W.↗

NASA NTRS2007

Dog-Bone Horns for Piezoelectric Ultrasonic/Sonic Actuators

A shape reminiscent of a dog bone has been found to be superior to other shapes for mechanical-amplification horns that are components of piezoelectrically driven actuators used in a series of related devices denoted generally as ultrasonic/sonic drill/corers (USDCs). The first of these devices was reported in Ultrasonic/Sonic Drill/Corers With Integrated Sensors (NPO-20856), NASA Tech Briefs, Vol. 25, No. 1 (January 2001), page 38. The dog-bone shape was conceived especially for use in a more recent device in the series, denoted an ultrasonic/ sonic gopher, that was described in Ultrasonic/Sonic Mechanisms for Drilling and Coring (NPO-30291), NASA Tech Briefs, Vol. 27, No. 9 (September 2003), page 65. The figure shows an example of a dog-bone-shaped horn and other components of an ultrasonic gopher. Prerequisite to a meaningful description of this development is an unavoidably lengthy recapitulation of the principle of operation of a USDC and, more specifically, of the ultrasonic/sonic gopher as described previously in NASA Tech Briefs. The ultrasonic actuator includes a stack of piezoelectric rings, the horn, a metal backing, and a bolt that connects the aforementioned parts and provides compressive pre-strain to the piezoelectric stack to prevent breakage of the rings during extension. The stack of piezoelectric rings is excited at the resonance frequency of the overall ultrasonic actuator. Through mechanical amplification by the horn, the displacement in the ultrasonic vibration reaches tens of microns at the tip of the horn. The horn hammers an object that is denoted the free mass because it is free to move longitudinally over a limited distance between hard stops: The free mass bounces back and forth between the ultrasonic horn and a tool bit (a drill bit or a corer). Because the longitudinal speed of the free mass is smaller than the longitudinal speed of vibration of the tip of the horn, contact between the free mass and the horn tip usually occurs at a phase of the vibration favorable to transfer of momentum from the horn to the free mass. Therefore, the free mass picks up momentum and is accelerated back to the tool bit. Upon impact of the free mass on the tool bit, momentum is transferred to the tool bit. The impacts of the free mass on the tool bit repeat at a sonic frequency that can range from tens of hertz to about 1 kHz. The shock waves caused by the impacts of the free mass propagate to the interface between the tool bit and the medium (typically, rock, ice, or other brittle material) to be drilled or cored. The medium becomes fractured when its ultimate strain is exceeded at the medium/tool-bit interface. This concludes the description of the principle of operation.

Sherrit, Stewart↗

NASA NTRS2002

Generalized Reliability Methodology Applied to Brittle Anisotropic Single Crystals

A generalized reliability model was developed for use in the design of structural components made from brittle, homogeneous anisotropic materials such as single crystals. The model is based on the Weibull distribution and incorporates a variable strength distribution and any equivalent stress failure criteria. In addition to the reliability model, an energy based failure criterion for elastically anisotropic materials was formulated. The model is different from typical Weibull-based models in that it accounts for strength anisotropy arising from fracture toughness anisotropy and thereby allows for strength and reliability predictions of brittle, anisotropic single crystals subjected to multiaxial stresses. The model is also applicable to elastically isotropic materials exhibiting strength anisotropy due to an anisotropic distribution of flaws. In order to develop and experimentally verify the model, the uniaxial and biaxial strengths of a single crystal nickel aluminide were measured. The uniaxial strengths of the <100> and <110> crystal directions were measured in three and four-point flexure. The biaxial strength was measured by subjecting <100> plates to a uniform pressure in a test apparatus that was developed and experimentally verified. The biaxial strengths of the single crystal plates were estimated by extending and verifying the displacement solution for a circular, anisotropic plate to the case of a variable radius and thickness. The best correlation between the experimental strength data and the model predictions occurred when an anisotropic stress analysis was combined with the normal stress criterion and the strength parameters associated with the <110> crystal direction.

Salem, Jonathan A.↗

DOE OSTI2025

Large scale polymer toughening of two-dimensional materials revealed by in situ TEM fracture tests and multiscale simulations

Two-dimensional (2D) materials offer significant potential for applications in energy-harvesting devices, batteries, sensors, and transistors. However, their intrinsic brittleness makes them prone to mechanical failure, limiting their practical use. In this work, we perform in situ transmission electron microscopy (TEM) fracture tests on monolayer MoSe2 and uncover an extrinsic toughening effect induced by an ultrathin adsorbed polystyrene adlayer. This adlayer substantially enhances the fracture resistance of the 2D flakes. Through a combination of molecular dynamics simulations and finite element analysis, we elucidate the molecular mechanism behind this toughening effect. Further, it arises from the active crack-bridging behavior of entangled polymer chains and the formation of a fracture process zone that stabilizes crack propagation and increases the energy required for crack extension. The proposed toughening mechanism offers a pathway to improving the mechanical reliability of 2D material-based devices by mitigating the risk of sudden failure.

2D materials↗

NASA NTRS2006

Molecular-dynamics Simulation-based Cohesive Zone Representation of Intergranular Fracture Processes in Aluminum

A traction-displacement relationship that may be embedded into a cohesive zone model for microscale problems of intergranular fracture is extracted from atomistic molecular-dynamics simulations. A molecular-dynamics model for crack propagation under steady-state conditions is developed to analyze intergranular fracture along a flat 99 [1 1 0] symmetric tilt grain boundary in aluminum. Under hydrostatic tensile load, the simulation reveals asymmetric crack propagation in the two opposite directions along the grain boundary. In one direction, the crack propagates in a brittle manner by cleavage with very little or no dislocation emission, and in the other direction, the propagation is ductile through the mechanism of deformation twinning. This behavior is consistent with the Rice criterion for cleavage vs. dislocation blunting transition at the crack tip. The preference for twinning to dislocation slip is in agreement with the predictions of the Tadmor and Hai criterion. A comparison with finite element calculations shows that while the stress field around the brittle crack tip follows the expected elastic solution for the given boundary conditions of the model, the stress field around the twinning crack tip has a strong plastic contribution. Through the definition of a Cohesive-Zone-Volume-Element an atomistic analog to a continuum cohesive zone model element - the results from the molecular-dynamics simulation are recast to obtain an average continuum traction-displacement relationship to represent cohesive zone interaction along a characteristic length of the grain boundary interface for the cases of ductile and brittle decohesion. Keywords: Crack-tip plasticity; Cohesive zone model; Grain boundary decohesion; Intergranular fracture; Molecular-dynamics simulation

Yamakov, Vesselin I.↗

NASA NTRS2007

Accounting for Uncertainties in Strengths of SiC MEMS Parts

A methodology has been devised for accounting for uncertainties in the strengths of silicon carbide structural components of microelectromechanical systems (MEMS). The methodology enables prediction of the probabilistic strengths of complexly shaped MEMS parts using data from tests of simple specimens. This methodology is intended to serve as a part of a rational basis for designing SiC MEMS, supplementing methodologies that have been borrowed from the art of designing macroscopic brittle material structures. The need for this or a similar methodology arises as a consequence of the fundamental nature of MEMS and the brittle silicon-based materials of which they are typically fabricated. When tested to fracture, MEMS and structural components thereof show wide part-to-part scatter in strength. The methodology involves the use of the Ceramics Analysis and Reliability Evaluation of Structures Life (CARES/Life) software in conjunction with the ANSYS Probabilistic Design System (PDS) software to simulate or predict the strength responses of brittle material components while simultaneously accounting for the effects of variability of geometrical features on the strength responses. As such, the methodology involves the use of an extended version of the ANSYS/CARES/PDS software system described in Probabilistic Prediction of Lifetimes of Ceramic Parts (LEW-17682-1/4-1), Software Tech Briefs supplement to NASA Tech Briefs, Vol. 30, No. 9 (September 2006), page 10. The ANSYS PDS software enables the ANSYS finite-element-analysis program to account for uncertainty in the design-and analysis process. The ANSYS PDS software accounts for uncertainty in material properties, dimensions, and loading by assigning probabilistic distributions to user-specified model parameters and performing simulations using various sampling techniques.

Nemeth, Noel↗

NASA NTRS1977

Continuous and cyclic thermal exposure induced degradation in boron reinforced 6061 aluminum composites

Boron reinforced 6061 aluminum (B/Al) composite was continuously exposed at 728 K for up to 240 hours and cyclically exposed between 293 K and 728 K for up to 6000 three-minute cycles. Room temperature tensile strengths were measured and the specimens were metallographically examined. The data suggest that, in addition to AlB2 formation, magnesium in the matrix diffused to the reaction layer and formed (Al,Mg)B2. This formation could weaken the matrix and embrittle the reaction layer. Continuous exposure degraded the strength of the B/Al specimens about 28% in 240 hours. However, the fracture mode, one indicative of high strength interfaces, did not change. The strength degradation was attributed to crack initiation in the brittle reaction layer causing stress concentrations in the fibers. Cyclic exposure degraded the strength of the B/Al about 34% in 6000 cycles. The fracture mode of the cyclic exposure specimens showed transition toward a mode characteristic of low interfacial strength. The lower interfacial strengths were attributed to stress fields induced by differential thermal expansion. Cyclic exposure degraded the strength of the B/Al specimens more than continuous exposure for similar cumulative exposure times.

Olsen, G. C.↗

NASA NTRS1987

Ceramics for engines

Structural ceramics were under nearly continuous development for various heat engine applications since the early 1970s. These efforts were sustained by the properties that ceramics offer in the areas of high-temperature strength, environmental resistance, and low density and the large benefits in system efficiency and performance that can result. The promise of ceramics was not realized because their brittle nature results in high sensitivity to microscopic flaws and catastrophic fracture behavior. This translated into low reliability for ceramic components and thus limited their application in engines. For structural ceramics to successfully make inroads into the terrestrial heat engine market requires further advances in low cost, net shape fabrication of high reliability components, and improvements in properties such as toughness, and strength. These advances will lead to very limited use of ceramics in noncritical applications in aerospace engines. For critical aerospace applications, an additional requirement is that the components display markedly improved toughness and noncatastrophic or graceful fracture. Thus the major emphasis is on fiber-reinforced ceramics.

Kiser, James D.↗

NASA NTRS2008

Impact Resistance of Uncoated SiC/SiC Composites

Two-dimensional woven SiC/SiC composites fabricated by melt infiltration method were impact tested at room temperature and at 1316 C in air using 1.59-mm diameter steel-ball projectiles at velocities ranging from 115 to 400 m/s. The extent of substrate damage with increasing projectile velocity was imaged and analyzed using optical and scanning electron microscopy, and non-destructive evaluation (NDE) methods such as pulsed thermography, and computed tomography. The impacted specimens were tensile tested at room temperature to determine their residual mechanical properties. Results indicate that at 115 m/s projectile velocity, the composite showed no noticeable surface or internal damage and retained its as-fabricated mechanical properties. As the projectile velocity increased above this value, the internal damage increased and mechanical properties degraded: At velocities >300 m/s, the projectile penetrated through the composite, but the composite retained approx.50% of the ultimate tensile strength of the as-fabricated composite and exhibited non-brittle failure. Predominant internal damages are delamination of fiber plies, fiber fracture and matrix shearing.

Bhatt, Ramakrishna T.↗

NASA NTRS2003

Lifetime Predictions of a Titanium Silicate Glass with Machined Flaws

A dynamic fatigue study was performed on a Titanium Silicate glass to assess its susceptibility to delayed failure and to compare the results with those of a previous study. Fracture mechanics techniques were used to analyze the results for the purpose of making lifetime predictions. The material strength and lifetime was seen to increase due to the removal of residual stress through grinding and polishing. Influence on time-to-failure is addressed for the case with and without residual stress present. Titanium silicate glass otherwise known as ultra-low expansion (ULE)* glass is a candidate for use in applications requiring low thermal expansion characteristics such as telescope mirrors. The Hubble Space Telescope s primary mirror was manufactured from ULE glass. ULE contains 7.5% titanium dioxide which in combination with silica results in a homogenous glass with a linear expansion coefficient near zero. delayed failure . This previous study was based on a 230/270 grit surface. The grinding and polishing process reduces the surface flaw size and subsurface damage, and relieves residual stress by removing the material with successively smaller grinding media. This results in an increase in strength of the optic during the grinding and polishing sequence. Thus, a second study was undertaken using samples with a surface finish typically achieved for mirror elements, to observe the effects of surface finishing on the time-to-failure predictions. An allowable stress can be calculated for this material based upon modulus of rupture data; however, this does not take into account the problem of delayed failure, most likely due to stress corrosion, which can significantly shorten lifetime. Fortunately, a theory based on fracture mechanics has been developed enabling lifetime predictions to be made for brittle materials susceptible to delayed failure. Knowledge of the factors governing the rate of subcritical flaw growth in a given environment enables the development of relations between lifetime, applied stress and failure probability for the material under study. Dynamic fatigue is one method of obtaining the necessary information to develop these relationships. In this study, the dynamic fatigue method was used to construct a time-to-failure diagram for polished ULE glass.

Tucker, Dennis S.↗

DOE OSTI2020

The effect of Ni doping on the mechanical behavior of tungsten

The effect of nickel (Ni) on activated sintering of tungsten has been known and investigated for decades. However, there are few reports on the mechanical properties of tungsten when Ni is added as a low alloying additive with less than 1 wt%. In this work, the mechanical behaviors of tungsten doped with 0.2–1.0 wt% nickel from room temperature up to 400 °C were investigated. The results show that the compression ductility of as-sintered Ni doped tungsten is drastically higher than that of as-sintered pure tungsten at all tested temperatures including room temperature, and the fracture toughness at room temperature is increased by 92%. The results suggest that the ductile-to-brittle transition temperature (DBTT) of tungsten can be reduced substantially by doping with Ni.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Analysis of attenuation data from the decommissioned ZIon unit 1 reactor pressure vessel beltline weld

In order to examine the attenuation of radiation damage through the thickness of an irradiated reactor pressure vessel (RPV), four segments were acquired from the Zion Unit 1 power plant RPV after the plant was decommissioned. The Zion Unit 1 RPV Beltline Weld Segment 1 was cut into seven blocks, consisting of five base metal and two beltline welds from the high fluence region of the segment. Through-wall test specimens were machined and tested. Specimens included those used for Charpy impact, Master Curve fracture toughness testing, and chemical analysis. The observed through-thickness ductile-to-brittle transition temperatures in the beltline weld deviated significantly from the expected behavior based on the attenuation of fast fluence as a function of depth into the RPV. Beginning at the inside surface, the 41-J Charpy transition temperature was either flat or slightly increasing until the ¾ -T location. The results of a simple, model-based analysis of the Zion beltline weld material that included the irradiation conditions and material chemistry were generally consistent with industry trend curves and the standard attenuation model, rather than the observed data. Although there was no archive material from the RPV available to permit measurement of the unirradiated properties, fracture toughness specimens fabricated from archive surveillance weld were used to obtain an estimate of the initial through-thickness values of the Charpy transition temperature. The Charpy shifts obtained using this approach were similarly in disagreement with the predictions of the US NRC Regulatory Guide 1.99, Rev. 2. However, testing of irradiated Charpy specimens taken from the RPV following post-irradiation annealing (10 hr. at 500 °C) provided a quite different estimate of the unirradiated properties which improved the agreement between the inferred through-thickness Charpy shifts and exponential attenuation model included in Regulatory Guide 1.99/2. In conclusion, the analysis of the Zion data and data obtained in previous post-mortem examinations of decommissioned RPVs indicates that more work is needed to understand the through-thickness properties of RPV materials in order to properly assess through-wall damage attenuation.

Charpy impact↗

DOE OSTI2021

Evaluating proxies for the drivers of natural gas productivity using machine-learning models

We report the extensive development of unconventional reservoirs using horizontal drilling and multistage hydraulic fracturing has generated large volumes of reservoir characterization and production data. The analysis of this abundant data using statistical methods and advanced machine-learning (ML) techniques can provide data-driven insights into well performance. Most predictive modeling studies have focused on the impact that different well completion and stimulation strategies have on well production but have not fully exploited the available in situ rock property data to determine its role in reservoir productivity. We have used machine-learning techniques to rank rock mechanical properties, microseismic attributes, and stimulation parameters in the order of their significance for predicting natural gas production from an unconventional reservoir. The data for this study came from a hydraulically fractured well in the Marcellus Shale in Monongalia County, West Virginia. The data classes included measurements aggregated by well completion stage that included (1) gas production, (2) well-log-derived measurements including bulk density, elastic moduli, shear impedance, compressional impedance, brittleness, and gamma measurements, (3) microseismic attributes, (4) long-period long-duration (LPLD) event counts, (5) fracture counts, and (6) stimulation parameters that included the fluid injection volume and average pumping pressure. To identify observable proxies for the drivers of gas production, we evaluated five commonly used ML approaches including multivariate adaptive regression spline, Gaussian mixture model, random forest, gradient boosting, and neural network. We selected five variables including LPLD event count, seismogenic b-value, hydraulic diffusivity, cumulative moment, and fluid volume as the features most likely to impact gas productivity at the stage level in the study area. The data-driven selection of these parameters for their importance in determining gas production can help reservoir engineers design more effective hydraulic-fracture treatments in the Marcellus Shale and other similar unconventional reservoirs. Plain language summary: We use machine-learning methods and data-driven selection of reservoir parameters to rank and better understand their importance in determining gas production, which can help reservoir engineers design more effective hydraulic-fracture treatments in the Marcellus Shale and other similar unconventional reservoirs.

58 GEOSCIENCES↗

DOE OSTI2026

Effect of deposition rate on microstructure and mechanical properties of 17-4 PH stainless steel fabricated by laser engineered net shaping

Laser engineered net shaping (LENS) is an additive manufacturing technique for fabricating and repairing metallic components. However, the relationships between its process parameters and the resulting mechanical properties of alloys such as 17-4 precipitation-hardening (PH) stainless steel require further investigation to enable reliable application. This study examines the specific effect of LENS deposition rate on the microstructure and mechanical properties of 17-4 PH stainless steel. Specimens were fabricated at two different deposition rates (8.47 and 9.31 mm s−1), subjected to subsequent solution and H900 aging treatment, and then evaluated via tensile testing, hardness measurements, and microscopy. A higher deposition rate results in a finer grain structure but increased porosity, leading to greater ultimate tensile strength (∼1294 MPa) yet lower ductility (strain at failure ∼5.8%) compared to the slower deposition rate (∼1266 MPa, ∼9.0% strain). Hardness follows the same trend as tensile strength. Tensile fracture surfaces for both conditions exhibited a mixed mode of ductile dimples and brittle quasi-cleavage regions, with chromium/silicon oxide particles identified within dimples. Complementary finite element modeling indicates that small void fractions primarily reduce ductility by enhancing localized plasticity, with only a marginal decrease in tensile strength. These integrated experimental and numerical results elucidate the mechanical properties linked to deposition rate, providing insight into tailoring LENS processes to achieve desired properties of 17-4 PH stainless steel.

17-4 PH stainlesssteel↗

DOE OSTI2023

Shinkolobweite, from the Shinkolobwe Mine, Democratic Republic of Congo: A New Mineral Containing Uranium in the Rare Pentavalent Oxidation State

ABSTRACT Shinkolobweite, Pb1.333[U5+O(OH)(UO2)5O4.67(OH)5.33](H2O)5, is a new lead uranyl oxide-hydroxide hydrate mineral containing hexavalent and pentavalent uranium from the Shinkolobwe mine, Democratic Republic of Congo. Crystals of shinkolobweite are dark reddish-brown prisms up to 0.5 mm in length, occurring on a matrix of massive uraninite associated with fourmarierite, rutherfordine, soddyite, and sklodowskite. Crystals are translucent with subadamantine luster and light bronze-yellow streak, are flattened on {010}, are elongated on [001], and exhibit the forms {100}, {010}, {101}, and . The mineral is non-fluorescent under both longwave and shortwave ultraviolet illumination. It has a Mohs hardness of ∼2 and exhibits brittle tenacity with perfect cleavage on {010}, imperfect cleavage on {100}, and even fracture. The calculated density is 5.853 g/cm3 based on the empirical formula. Electron probe microanalysis provided the empirical formula Pb1.290U6+4.876U5+1.166O27H16.633 based on 27 O apfu and U5+:U6+ determined by X-ray photoelectron spectroscopy. Shinkolobweite is orthorhombic, superspace group Pnnm(0b0)000, a = 14.4808(4), b = 7.0681(8), c = 11.9423(3) Å, V = 1222.32(15) Å3, modulation wave vector [0 1/3 0], and Z = 2. The structure was refined from 8959 reflections to a final R1 = 0.0736 for all reflections. Uranyl oxide-hydroxide sheets in shinkolobweite adopt the β-U3O8 topology and possess (3 + 1) commensurately modulated ordering that results from the long-range ordering of U5+ and U6+ in the sheet, as well as the position and occupancy of interlayer Pb2+ cations. Observations of a topological transition between α-U3O8 and β-U3O8 type sheets in shinkolobweite supplements our understanding of U5+ mineral oxidation and stability.

Mineralogy↗