Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “atomic volume”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

A solid-state extrusion pathway extensible to upcycling aluminum scrap and end-of-life permanent magnets into ductile Al-6061/SmCo 5 structural magnetic composites

Permanent magnets offer strong potential for multifunctional structural components, but their inherent brittleness limits direct integration. Here, SolidStir® Extrusion (SSE) is used to embed SmCo5 powder into AA6061 in the solid state, and the resulting microstructure, interfacial chemistry, mechanical properties, and magnetic response are systematically characterized. SSE fragments the initial SmCo 5 powder into predominantly fine particles dispersed within an ultrafine Al matrix, with a volume fraction of ∼ 4–6 % in this proof-of-concept study. Interfacial reactions form a continuous Al–Co reaction layer, with local atomic-resolution indexing consistent with Al 13 Co 4 , together with Sm–Si-rich reaction products, while the matrix contains Sm–Co–Si-rich precipitates and Mg 2 Si, producing features from nanometers to micrometers. Compared with an Al extrudate, this architecture increases yield strength by ∼ 42 % and tensile strength by ∼ 31 %, while preserving uniform elongation, and it sustains work hardening in compression from 150 to 400 °C. The composite retained hard-magnetic behavior, with axial magnetization of 12.7 A·m 2 kg −1 at 6 T and intrinsic coercivity of 9.6 kOe. These findings demonstrate that SSE can produce Al-based load-bearing magnetic composites while preserving useful SmCo5 functionality.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Coordinatively and Spatially Coconfining High-Loading Atomic Sb in Sulfur-Rich 2D Carbon Matrix for Fast K + Diffusion and Storage

The atomically dispersed materials promise ultrafast redox kinetics for alkali-ion storage. However, their relatively low mass loading limits their application. In this work, well-dispersed Sb atoms with high-loading of 23.3 wt % anchored in sulfur-rich amorphous carbon-coated reduced graphene oxide matrix (SbSA/C) are prepared by a coordinative and spatial coconfinement methodology including freeze-casting the well-dissolved Sb-chelates (Sb-thioglycolate) within graphene oxide suspension and post heating-treatment. The reduced graphene oxide substrate features open two-dimensional spatial framework for loading atomically dispersive Sb species, and the pyrolyzed Sb-chelates would provide not only massive desirable heteroatoms (S, O) for coordinating the Sb atoms but also in situ pyrolytic carbon for further spatially separating those dispersive atoms. The coordinative and spatial coconfinement engineering also endows the SbSA/C composite with atomic-level Sb atoms against migration and agglomeration during electrochemical K-storage cycling. In situ TEM reveals the uniform potassiation behavior of the SbSA/C without obvious volume change; DFT calculation and electrochemical characterization suggest the significantly lower K-ion diffusion energy barrier. Therefore, on the basis of both the active Sb center and the coordinative heteroatom, the SbSA/C electrode delivers high fast-charging capacity, outstanding rate capability and long-lifespan performance in half/full K-ion batteries (e.g., a stable capacity of 331.3 mA h g –1 is maintained over 1100 cycles at 1.0 A g –1 for half-cell).

36 MATERIALS SCIENCE↗
DOE OSTI2025

Pulse Shape Discrimination in JSNS 2

JSNS 2 (J-PARC Sterile Neutrino Search at J-PARC Spallation Neutron Source) is an experiment that is searching for sterile neutrinos via the observation of $\overline{ν}$ μ → $\overline{ν}$ e appearance oscillations using neutrinos from muon decay-at-rest. For this search, rejecting cosmic-ray-induced neutron events by Pulse Shape Discrimination (PSD) is essential because the JSNS2 detector is located above ground, on the third floor of the building. We have achieved 94.95% ± 0.15% rejection of neutron events while keeping 92.82% ± 1.77% of signal, electron-like events using a data-driven likelihood method. This article will report the PSD technique using the full fiducial volume of the JSNS2 detector.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
NASA NTRS1985

Liquid rocket combustor computer code development

The Advanced Rocket Injector/Combustor Code (ARICC) that has been developed to model the complete chemical/fluid/thermal processes occurring inside rocket combustion chambers are highlighted. The code, derived from the CONCHAS-SPRAY code originally developed at Los Alamos National Laboratory incorporates powerful features such as the ability to model complex injector combustion chamber geometries, Lagrangian tracking of droplets, full chemical equilibrium and kinetic reactions for multiple species, a fractional volume of fluid (VOF) description of liquid jet injection in addition to the gaseous phase fluid dynamics, and turbulent mass, energy, and momentum transport. Atomization and droplet dynamic models from earlier generation codes are transplated into the present code. Currently, ARICC is specialized for liquid oxygen/hydrogen propellants, although other fuel/oxidizer pairs can be easily substituted.

Liang, P. Y.↗
NASA NTRS1996

Spray Diagnostics in Rocket Engines Using Phase Doppler Analyzer

Characteristics such as drop velocity, drop size, number density, volume flow rate, volume flux, and evaporation rate of the fuel spray in a rocket engine are directly related to engine performance. Several studies of shear coaxial atomization have been done in the past. However, additional work related to sprays at supercritical and transcritical conditions would be useful. The author undertook a study of the feasibility of using a phase Doppler particle analyzer (PDPA) for spray measurements in rocket engines as a part of the Summer Faculty Fellowship Program at the NASA Marshall Space Flight Center. The PDPA is a single particle counter (SPC) system based on light scattering from spherical particles. The PDPA instrument is based on refractive and reflective scattering as opposed to other instruments based on diffractive scattering. The main advantage of the PDPA instrument is its ability to provide point-wise information. The following sections describe the principle of operation of the PDPA system and the data obtained using a PDPA instrument in a spray formed by a commercially available fuel injection nozzle.

Isaac, Kakkattukuzhy M.↗
NASA NTRS2005

Design Concept for a Reusable/Propellantless MXER Tether Space Transportation System

The Momentum Exchange/Electrodynamic Reboost (MXER) tether facility is a transformational concept that significantly reduces the fuel requirements (and associated costs) in transferring payloads above low earth orbit (LEO). Facility reboost is accomplished without propellant by driving current against a voltage created by a conducting tether's interaction with the Earth's magnetic field (electrodynamic reboost). This system can be used for transferring a variety of payloads (scientific, cargo, and human space vehicles) to multiple destinations including geosynchronous transfer orbit, the Moon or Mars. MXER technology advancement requires development in two key areas: survivable, high tensile strength non-conducting tethers and reliable, lightweight payload catch/release mechanisms. Fundamental requirements associated with the MXER non-conducting strength tether and catch mechanism designs will be presented. Key requirements for the tether design include high specific-strength (tensile strength/material density), material survivability to the space environment (atomic oxygen and ultraviolet radiation), and structural survivability to micrometeoroid/orbital debris (MM/OD) impacts. The driving mechanism key,gequirements include low mass-to-capture-volume ratio, positional and velocity error tolerance, and operational reliability. Preliminary tether and catch mechanism design criteria are presented, which have been used as guidelines to "screen" and down-select initial concepts. Candidate tether materials and protective coatings are summarized along with their performance in simulated space environments (e.g., oxygen plasma, thermal cycling). A candidate catch mechanism design concept is presented along with examples of demonstration hardware.

McCandless, B., II↗
DOE OSTI2020

Analysis of the Stable Interphase Responsible for the Excellent Electrochemical Performance of Graphite Electrodes in Sodium-Ion Batteries

Considerable efforts have been exerted to understand the formation and properties of the solid electrolyte interphase (SEI) in sodium ion batteries. However, the puzzling existence and role of SEI behind the huge volume changes of the graphite electrodes need to be answered. Herein, the reason of how ether-derived SEI maintains excellent reversibility despite the huge volume changes during cycling is unraveled. Theoretical simulations and Fourier-transform infrared spectroscopy demonstrate the formation mechanism of an SEI between the graphite anode and electrolyte. Furthermore, the high mechanical tolerance of the ether-derived SEI is confirmed in atomic force microscopy. A depth profile of X-ray photoelectron spectroscopy points to a multilayer structure of the ether-derived SEI. The outer layer comprises organics (sodium alkoxide), while the inorganics (Na 2 CO 3 , NaF) in interior region are mixed with some organics. Notably, the presence of organics ensures the adaptability of the SEI to the volume expansion of graphite during cycling, and the concentrated distribution of inorganics improves the Young's modulus (resistance to deformation). Therefore, the graphite anode exhibits high cycle stability (96.6% capacity retention ratio at 1 A g –1 over 860 cycles) and efficiency (≈99.5%).

25 ENERGY STORAGE↗
DOE OSTI2021

Machine Learning Predictions of Transition Probabilities in Atomic Spectra

Forward modeling of optical spectra with absolute radiometric intensities requires knowledge of the individual transition probabilities for every transition in the spectrum. In many cases, these transition probabilities, or Einstein A-coefficients, quickly become practically impossible to obtain through either theoretical or experimental methods. Complicated electronic orbitals with higher order effects will reduce the accuracy of theoretical models. Experimental measurements can be prohibitively expensive and are rarely comprehensive due to physical constraints and sheer volume of required measurements. Due to these limitations, spectral predictions for many element transitions are not attainable. In this work, we investigate the efficacy of using machine learning models, specifically fully connected neural networks (FCNN), to predict Einstein A-coefficients using data from the NIST Atomic Spectra Database. For simple elements where closed form quantum calculations are possible, the data-driven modeling workflow performs well but can still have lower precision than theoretical calculations. For more complicated nuclei, deep learning emerged more comparable to theoretical predictions, such as Hartree–Fock. Unlike experiment or theory, the deep learning approach scales favorably with the number of transitions in a spectrum, especially if the transition probabilities are distributed across a wide range of values. It is also capable of being trained on both theoretical and experimental values simultaneously. In addition, the model performance improves when training on multiple elements prior to testing. The scalability of the machine learning approach makes it a potentially promising technique for estimating transition probabilities in previously inaccessible regions of the spectral and thermal domains on a significantly reduced timeline.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2020

Tritiated Water Disposition Strategies

Tritium, a radioactive isotope of hydrogen, is typically confined within one or more confinement barriers. Tritium readily reacts with oxygen to form tritiated water or can exchange with protium or deuterium atoms in water to create tritiated water which is around 10,000 times more toxic than elemental tritium. Primary tritium confinement systems can create small volumes of highly tritiated water. Secondary confinement systems, like inert gloveboxes, will produce larger volumes of lower concentration tritiated water. Much larger volumes of tritiated water of very low tritium content are produced by tritium permeation/diffusion. Tritium from inside primary and secondary confinement barriers will diffuse from these systems into cooling water systems. Closed loop, recirculating cooling water systems will slowly accumulate tritium and create concentrations which exceed drinking water (or permitted discharge) concentrations. The cooling water systems designed as series of interconnected cooling loops that can slowly transfer tritium from one cooling loop to another cooling loop through heat exchangers. These large volumes of tritiated water may be above federal discharge limits and also lack convenient disposition pathways. This document will discuss tritiated water management strategies from the perspective of large volume, low tritium concentrations that exceed drinking water or permitted discharge limits. Applicable US regulatory requirements for a Molybdenum-99 (Mo-99) production facility concerning tritiated water are also cited. Tritiated water disposition options, based on typical waste minimization strategies will guide dispositions options. A Case Study example is presented to illustrate the pros and cons of several disposition options. The report does not recommend any particular disposition pathway but discusses strategies to be explored by a producer to guide selection of processes which best fits the needs of a particular waste stream.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1990

Influence of the continuous and dispersed phases on the symmetry of a gas turbine air-blast atomizer

Current trends in liquid-fueled practical combustion systems are leaving less tolerance for fuel injection deficiencies such as poor spray field symmetry. The present paper evaluates the symmetry of the flowfield produced by a practical airblast atomizer. Specifically, the influence of both the continuous phase and dispersed phase on the spray field symmetry is assessed. In the present case, asymmetry in volume flux is associated principally with disparities in the injection of the dispersed phase, which is manifested by a maldistribution of larger drops. Asymmetries observed in the continuous phase without the dispersed phase are reduced in magnitude by the presence of the dispersed phase, but still contribute to asymmetry in radial spread of the dispersed phase.

Mcdonell, V. G.↗
NASA NTRS1992

FNAS modify matric and transparent experiments

Monotectic alloy materials are created by rapid melt/rapid solidification processing on the NASA KC-135. Separation of the uniform liquid into two liquids may occur by either of two processes; spinodal decomposition or nucleation followed by growth. In the first case, the liquid is unstable to composition waves, which form and grow, giving liquids of two different compositions. In the latter process discrete particles of the second liquid phase form via thermal fluctuations and then grow by diffusion. The two processes are very different, with the determining process being dictated by temperature, composition, and thermodynamic characteristics of the alloy. The first two quantities are process variables, while the third is determined by electronic interactions between the atoms in the alloy. In either case the initial alloy decomposition is followed by coarsening, resulting in growth of the particle size at nearly constant volume fraction. In particular, reduced gravity experiments on monotectic solutions have shown a number of interesting results in the KC-135. Monotectic solutions exhibit a miscibility gap in the liquid state, and consequently, gravity driven forces can dominate the solidification parameters at 1 g. In reduced gravity however, the distribution of the phases is different, resulting in new and interesting microstructures. The Rapid Melt/Rapid Quench Furnace allows one to melt a sample and resolidify it in one parabola of the KC-135's flight path, thus eliminating any accumulative influence of multiple parabolas to affect the microstructure of the material.

Smith, Guy A.↗
NASA NTRS2003

One-liter Hg ion clock for space and ground applications

We describe the development of a small Hg ion clock suitable for space use. A small clock occupying 1-2 liters volume and producing stability of 10 to the power negative twelve, divided by square root pi would significantly advance the state of space-qualified atomic clocks. Based on recent measurements, this technology should produce long-term stability as good as 10 to the power negative fifteen.

ion clock↗
NASA NTRS2018

Relative Sputtering Rates of FeS, MgS, and Mg Silicates: Implications for ISM Gas Phase Depletions of Rock-Forming Elements

Astronomical measurements of S abundances in the diffuse interstellar medium (ISM) indicate ionized S is a dominant species with little (< 5%) S residing in grains (e.g. Jenkins 2009). This is an enigmatic result, given that abundant Fe-sulfide grains are observed in dust around pre- and post-main sequence stars and are also observed as major components of primitive meteoritic and cometary samples. These disparate observations suggest that the lifetime of sulfide grains in the ISM is short because of destruction processes. Our previous work has shown that FeS and MgS retain their crystallinity and do not amorphize during radiation processing, whereas enstatite and forsterite are readily amorphized. We have extended this study to measure the relative sputtering rates of FeS and MgS compared to enstatite and forsterite. Irradiation of FeS with 4 keV He+ results in preferential sputtering of S and the formation of a thin 2-3 nm, compact Fe metal layer that armors the surface. The zone of S loss extends to a depth of ~8-10 nm below the exposed surface. Despite this S loss, the FeS retains its crystallinity and shows no sign of incipient amorphization. Irradiation of FeS with 5kV Ga+ in a focused ion beam (FIB) instrument resulted in preferential sputtering of S and the formation of a 5-8-nm thick surface layer of nanophase Fe metal. X-ray mapping shows that the zone of S sputtering extends to a depth of nearly 20 nm, but there is no evidence for FeS amorphization, consistent with our previous work. The irradiation experiments show that the relative sputtering rate of FeS and MgS are much higher than olivine or enstatite. Sputtering experiments utilizing 30 kV and 5 kV Ga ions in the FIB produced volume loss in troilite that was ~4X greater than in enstatite or forsterite. The sputter yield under these conditions is such that for every Si atom sputtered from enstatite, ~14 S atoms are sputtered from FeS. We have performed similar sputtering experiments on Fe-bearing niningerite (MgS) and co-existing enstatite from the ALH 84170 EH3 chondrite. MgS also sputters much more rapidly than enstatite with a relative Si:S sputter yield of 1:8. For MgS, sulfur is highly depleted at the surface and the S-depletion zone extends to a depth of ~15 nm (using 5 kV Ga+). There is a corresponding zone of Mg and especially Fe enrichment that extends from 5 to ~10 nm below the surface, respectively. The dominant grain destruction mechanism in the ISM is sputtering from passage of supernova-generated shock waves. This process also results in the amorphization of crystalline silicates in the ISM. Our results indicate that FeS and MgS grains produced in evolved stars and injected into the ISM will be destroyed more rapidly than crystalline silicates. This process may account for the lack of significant depletion of S from the gas phase in the ISM. However, rare nanophase FeS grains occur as inclusions in circumstellar amorphous silicate grains found in comet dust particles analyzed in the laboratory. These results show that a finite amount of S in the ISM is sequestered in solid grains.

SPUTTERING RATES↗
DOE OSTI2022

Snowmass 2021 Cosmic Frontier White Paper: Cosmology with Millimeter-Wave Line Intensity Mapping

Next-generation tests of fundamental physics and cosmology using large scale structure require measurements over large volumes of the Universe, including high redshifts inaccessible to present-day surveys. Line intensity mapping, an emerging technique that detects the integrated emission of atomic and molecular lines without resolving sources, can efficiently map cosmic structure over a wide range of redshifts. Observations at millimeter wavelengths detect far-IR emission lines such as CO/[CII], and take advantage of observational and analysis techniques developed by CMB experiments. These measurements can provide constraints with unprecedented precision on the physics of inflation, neutrino masses, light relativistic species, dark energy and modified gravity, and dark matter, among many other science goals. In this white paper we forecast the sensitivity requirements for future ground-based mm-wave intensity mapping experiments to enable transformational cosmological constraints. We outline a staged experimental program to steadily improve sensitivity, and describe the necessary investments in developing detector technology and analysis techniques.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2024

Crystal Growth of Cesium Hafnium Chloride (Cs2HfCl6) Scintillating Crystal

Crystal growth is the process where crystalline substance forms and increases in size through the addition of atoms, ions, or molecules. In this research we used the Bridgman technique to grow Cesium Hafnium Chloride (C2HfCl6). This technique is ideal for growing large volume crystal. Using a vertical furnace with two heating zones for heating and cooling. the material solidifies into a crystal as it slowly transitions from hot to cold zone.

Tribble, Jalen↗
NASA NTRS2010

Nonlinear Dynamics of Cantilever-Sample Interactions in Atomic Force Microscopy

The interaction of the cantilever tip of an atomic force microscope (AFM) with the sample surface is obtained by treating the cantilever and sample as independent systems coupled by a nonlinear force acting between the cantilever tip and a volume element of the sample surface. The volume element is subjected to a restoring force from the remainder of the sample that provides dynamical equilibrium for the combined systems. The model accounts for the positions on the cantilever of the cantilever tip, laser probe, and excitation force (if any) via a basis set of set of orthogonal functions that may be generalized to account for arbitrary cantilever shapes. The basis set is extended to include nonlinear cantilever modes. The model leads to a pair of coupled nonlinear differential equations that are solved analytically using a matrix iteration procedure. The effects of oscillatory excitation forces applied either to the cantilever or to the sample surface (or to both) are obtained from the solution set and applied to the to the assessment of phase and amplitude signals generated by various acoustic-atomic force microscope (A-AFM) modalities. The influence of bistable cantilever modes of on AFM signal generation is discussed. The effects on the cantilever-sample surface dynamics of subsurface features embedded in the sample that are perturbed by surface-generated oscillatory excitation forces and carried to the cantilever via wave propagation are accounted by the Bolef-Miller propagating wave model. Expressions pertaining to signal generation and image contrast in A-AFM are obtained and applied to amplitude modulation (intermittent contact) atomic force microscopy and resonant difference-frequency atomic force ultrasonic microscopy (RDF-AFUM). The influence of phase accumulation in A-AFM on image contrast is discussed, as is the effect of hard contact and maximum nonlinearity regimes of A-AFM operation.

Cantrell, John H.↗
DOE OSTI2024

Progress Report for W911NF-23-1-0323: Development of Scalable Three-Dimensional Ion Traps for Quantum Information Processing

Trapped atomic ions are a promising platform for scalable quantum information processing. They lead in many key metrics such as single and two qubit gate fidelities, as well as quantum volume. We recently realized novel 3D ion traps with a high resolution 3D-printing process. The traps combine the scalability potential of surface chip traps with the superior trap performance of macroscopic 3D ion traps. Like photolithography, 3D-printing is a digitally defined process and hence allows for rapid iteration between design and fabrication. In contrast to photolithography, it also allows for fully defined 3D structures and, thus, is an ideal process to develop large, well-defined trap arrays with complex 3D electrode structures. Our current goal is to implement key procedures and perform critical measurements that justify incorporation of 3D-printed traps into large-scale quantum computing efforts. En route, we recently realized trapping in horizontal traps that are operating at cryogenic temperatures.

74 ATOMIC AND MOLECULAR PHYSICS↗
NASA NTRS2001

Toward a Micro Gas Chromatograph/Mass Spectrometer (GC/MS) System

Miniature mass filters (e.g., quadrupoles, ion traps) have been the subject of several miniaturization efforts. A project is currently in progress at JPL to develop a miniaturized Gas Chromatograph/Mass Spectrometer (GC/MS) system, incorporating and/or developing miniature system components including turbomolecular pumps, scroll type roughing pump, quadrupole mass filter, gas chromatograph, precision power supply and other electronic components. The preponderance of the system elements will be fabricated using microelectromechanical systems (MEMS) techniques. The quadrupole mass filter will be fabricated using an X-ray lithography technique producing high precision, 5x5 arrays of quadrupoles with pole lengths of about 3 mm and a total volume of 27 cubic mm. The miniature scroll pump will also be fabricated using X-ray lithography producing arrays of scroll stages about 3 mm in diameter. The target detection range for the mass spectrometer is 1 to 300 atomic mass units (AMU) with are solution of 0.5 AMU. This resolution will allow isotopic characterization for geochronology, atmospheric studies and other science efforts dependant on the understanding of isotope ratios of chemical species. This paper will discuss the design approach, the current state-of-the art regarding the system components and the progress toward development of key elements. The full system is anticipated to be small enough in mass, volume and power consumption to allow in situ chemical analysis on highly miniaturized science craft for geochronology, atmospheric characterization and detection of life experiments applicable to outer planet roadmap missions.

Wiberg, D. V.↗