Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “aqueous processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Direct Air Capture of CO 2 with Aqueous Amino Acids and Solid Bis-iminoguanidines (BIGs)

We report a bench-scale direct air capture (DAC) process comprising CO 2 absorption with aqueous amino acid salts (i.e., potassium glycinate, potassium sarcosinate), followed by room-temperature regeneration of the amino acids by reaction with solid meta-benzene-bis(iminoguanidine) (m-BBIG), resulting in crystallization of the hydrated m-BBIG carbonate salt, (m-BBIGH 2 )(CO 3 )(H 2 O) n (n = 3–4). The CO 2 is subsequently released by mild heating (60–120 °C) of the carbonate crystals, which regenerates the m-BBIG solid quantitatively. This low-temperature crystallization-based DAC process circumvents the need to heat the aqueous amino acid sorbents, thereby minimizing their loss through thermal and oxidative degradation. The CO 2 cyclic capacity for the sarcosine/m-BBIG system, measured over three consecutive absorption/regeneration cycles, is in the range of 0.12–0.20 mol/mol. The regeneration energy of m-BBIG, comprising the enthalpy of CO 2 and water release, and the sensible heat, is 360 kJ/mol (8.2 GJ/ton CO 2 ). Alternatively, the aqueous amino acids can be regenerated by boiling under reflux, with measured cyclic capacities of up to 0.64 mol/mol.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Chloride-Based Volatility for Waste Reduction and/or Reuse of Metallic-, Oxide- and Salt-Based Reactor Fuels

The objective of the chloride based volatility project (CBV) was to demonstrate the ability to separate uranium from used fuel to enable process improvements resulting in 10x reduction of waste volume, while maintaining safeguards standards and global backend costs at $\$$1/MW-hr. Current industrial practices perform separations of used fuel using solvent media in the form of aqueous and molten salt processes, resulting in contaminated process waste. The CBV approach utilized solid state chemistry with no solvent media and was successful in chlorinating uranium and fission product oxides that sublimed into the gas phase and were collected in targeted condensation zones based on temperature gradients of chlorinated products. Recovery of better than 95% of initial uranium in the form of UCl4 was demonstrated when simulated used nuclear fuel was used. Laser induced breakdown spectroscopy, LIBS, and ultraviolet-visible spectroscopy, UV-Vis, were combined into a high temperature flow cell design and utilized as process monitoring techniques to observed chlorinated products leave the reaction vessel in real time.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Dry Pretreatment of Used Nuclear Fuel for Tritium Removal: A Review

Virtually all the elements in the periodic chart are generated as a result of atomic fission in nuclear fuel. Several of the elements are volatile or can readily react with other chemicals to form volatile molecules that can be released during the processing of used nuclear fuel for the recovery of the valuable products. Among the volatile fission products, {sup 129}I, {sup 14}C, {sup 3}H, {sup 85}Kr, and {sup 79}Se constitute the main environmental concern for uncontrolled release. Storage of used fuel allows the short-lived isotopes to decay significantly (e.g., {sup 3}H decays in half every 12.32 years and {sup 85}Kr every 10.76 years). However, depending on regulatory limits they may remain an environmental concern up to about 50-100 years of fuel storage. In contrast, the concern for environmental release of the highly mobile {sup 129}I and {sup 14}C remains for geological times (half-lives of 15.7 million years for {sup 129}I and 5730 years for {sup 14}C). Processing of used commercial nuclear fuel requires significant head-end operations to remove the fuel from the protective coverings (e.g., assemblies). The current industrial process includes cropping the end caps of the fuel assemblies, chopping of the fuel pins and/or bundles into short segments, and prolonged leaching of the segments using concentrated nitric acid (HNO{sub 3}). The infrastructure, processes, and waste treatment systems in the head-end operations, including the associated off-gas system, are some of the larger and more costly components of the entire plant. The bulk of the volatile fission products are released to the off-gas during the leaching and dissolution. However, a small but significant amount will transfer to the following steps of processing such as solvent extraction and will show up in many different waste streams. The effective capture of {sup 3}H and iodine throughout the different processes and disposition of associated waste streams is costly and complicated. Up-front removal and capture is highly desirable. Currently, at the U.S. Department of Energy national laboratories and internationally, several dry pretreatment technologies are being studied and developed with the potential to simplify and increase the safety of subsequent storage or chemical recycling processes. These studies include (1) alternative decladding methods, (2) oxidation of exposed fuel following either conventional shearing or chemical decladding, and (3) the collection and stabilization of released volatile radionuclides. Several dry processes are being developed for the up-front removal of tritium and other fission products. They can be combined with different decladding alternatives and, in general, produce a fine powder that can be fed to aqueous or pyrochemical separations processes. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Aqueous proton transfer across single-layer graphene

Proton transfer across single-layer graphene proceeds with large computed energy barriers and is therefore thought to be unfavourable at room temperature unless nanoscale holes or dopants are introduced, or a potential bias is applied. Here we subject single-layer graphene supported on fused silica to cycles of high and low pH, and show that protons transfer reversibly from the aqueous phase through the graphene to the other side where they undergo acid–base chemistry with the silica hydroxyl groups. After ruling out diffusion through macroscopic pinholes, the protons are found to transfer through rare, naturally occurring atomic defects. Computer simulations reveal low energy barriers of 0.61–0.75 eV for aqueous proton transfer across hydroxyl-terminated atomic defects that participate in a Grotthuss-type relay, while pyrylium-like ether terminations shut down proton exchange. Unfavourable energy barriers to helium and hydrogen transfer indicate the process is selective for aqueous protons.

36 MATERIALS SCIENCE↗

Closed Fuel Cycle Waste Treatment Strategy

This study is aimed at evaluating the existing waste management approaches for nuclear fuel cycle facilities in comparison to the objectives of implementing an advanced fuel cycle in the U.S. under current legal, regulatory, and logistical constructs. The study begins with the Global Nuclear Energy Partnership (GNEP) Integrated Waste Management Strategy (IWMS) (Gombert et al. 2008) as a general strategy and associated Waste Treatment Baseline Study (WTBS) (Gombert et al. 2007). The tenets of the IWMS are equally valid to the current waste management study. However, the flowsheet details have changed significantly from those considered under GNEP. In addition, significant additional waste management technology development has occurred since the GNEP waste management studies were performed. This study updates the information found in the WTBS, summarizes the results of more recent technology development efforts, and describes waste management approaches as they apply to a representative full recycle reprocessing flowsheet. Many of the waste management technologies discussed also apply to other potential flowsheets that involve reprocessing. These applications are occasionally discussed where the data are more readily available. The report summarizes the waste arising from aqueous reprocessing of a typical light-water reactor (LWR) fuel to separate actinides for use in fabricating metal sodium fast reactor (SFR) fuel and from electrochemical reprocessing of the metal SFR fuel to separate actinides for recycle back into the SFR in the form of metal fuel. The primary streams considered and the recommended waste forms include; Tritium in low-water cement in high integrity containers (HICs); Iodine-129: As a reference case, a glass composite material (GCM) formed by the encapsulation of the silver Mordenite (AgZ) getter material in a low-temperature glass is assumed. A number of alternatives with distinct advantages are also considered including a fused silica waste form with encapsulated nano-sized AgI crystals; Carbon-14 immobilized as a CaCO3 in a cement waste form; Krypton-85 stored as a compressed gas; An aqueous reprocessing high-level waste (HLW) raffinate waste immobilized by the vitrification process; An undissolved solids (UDS) fraction from aqueous reprocessing of LWR fuel either included in the borosilicate HLW glass or immobilized in the form of a metal alloy or titanate ceramics; Zirconium-based LWR fuel cladding hulls and stainless steel (SS) fuel assembly hardware super-compacted for disposal or purified for reuse (or disposal as low-level waste, LLW) of Zr by reactive gas separations; Electrochemical process salt HLW incorporated into a glass bonded Sodalite waste form; and Electrochemical process UDS and SS cladding hulls melted into an iron based alloy waste form. Mass and volume estimates for each of the recommended waste forms based on the source terms from a representative flowsheet are reported. In addition to the above listed primary waste streams, a range of secondary process wastes are generated by aqueous reprocessing of LWR fuel, metal SFR fuel fabrication, and electrochemical reprocessing of SFR fuel. These secondary wastes have been summarized and volumes estimated by type and classification. The important waste management data gaps and research needs have been summarized for each primary waste stream and selected waste process.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Perspectives on the relationship between materials chemistry and roll-to-roll electrode manufacturing for high-energy lithium-ion batteries

As lithium-ion battery (LIB) active material and cell manufacturing costs continue to drop with wider adoption of electric vehicles, electrode and cell processing costs remain too high in terms of reaching the ultimate U.S. Department of Energy (DOE) cell cost target of $80/kWh. This paper primarily covers major materials chemistry advancements made over the last 10 years at Oak Ridge National Laboratory (ORNL) in the space of advanced manufacturing science for LIBs with the aim of simultaneously meeting the ultimate cost target, 500 Wh/kg gravimetric energy density, 10-15-min fast charge times, and 1000 deep discharge cycles. Aqeous electrode processing with a variety of active anode and cathode materials is now a standard procedure at the DOE Battery Manufacturing R&D Facility at ORNL (BMF), including the latest processes developed for Ni-rich cathodes. New results on cobalt-free LiNi 0.8 Fe 0.1 Al 0.1 O 2 (NFA 811) are also included and discussed in an electrode processing advantage context. In addition, colloidal processing advancements have been made for Si/C composite anodes for achieving >600 mA h/g capacities. Optimization of electrode coating parameters and drying protocols have been completed, which has elucidated how key processing variables need to be changed when parameters such as slurry solids loading, solvent type, and wet electrode thickness are changed. ORNL has also increased the line speeds at which thick cathodes can be processed using ultra-fast electron beam (EB) curing and substantially decreased formation cycling times to <1 day. Finally, key details of these advancements are discussed in the context of materials chemistry and process-property-performance relationships.

25 ENERGY STORAGE↗

Probing Complex Chemical Processes at the Molecular Level with Vibrational Spectroscopy and X-ray Tools

Understanding the origins of structure and bonding at the molecular level in complex chemical systems spanning magnitudes in length and time is of paramount interest in physical chemistry. Here, we have coupled vibrational spectroscopy and X-ray based techniques with a series of microreactors and aerosol beams to tease out intricate and sometimes subtle interactions, such as hydrogen bonding, proton transfer, and noncovalent interactions. This allows for unraveling the self-assembly of arginine-oleic acid complexes in an aqueous solution and growth processes in a metal–organic framework. Terahertz and infrared spectroscopy provide an intimate view of the hydrogen-bond network and associated phase changes with temperature in neopentyl glycol. The hydrogen-bond network in aqueous glycerol aerosols and levels of protonation of nicotine in aqueous aerosols are visualized. Future directions in probing the hydrogen-bond networks in deep eutectic solvents and organic frameworks are described, and we suggest how X-ray scattering coupled to X-ray spectroscopy can offer insight into the reactivity of organic aerosols.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A pilot-process for calcium hydroxide production from iron slag by low-temperature precipitation

The production of Ca(OH) 2 via thermal decomposition of limestone is an energy intensive process resulting in significant CO 2 emissions. However, if produced in a manner that obviates the need for the thermal decomposition of limestone, Ca(OH) 2 could be a “CO 2 -negative” material. Herein, we design and demonstrate the operation of a continuous, low-temperature (< 100 °C), aqueous-phase pilot-process to produce Ca(OH) 2 using calcium extracted from alkaline industrial wastes. The three-step process encompasses unit operations including: (i) calcium leaching from basic oxygen furnace BOF slag, (ii) leachate concentration by reverse osmosis (RO), and (iii) Ca(OH) 2 precipitation by temperature swing. Here this process presents several advantages compared to the traditional route. First, it advances the recycling of waste from the steel industry. Second, it operates significantly below the temperature used in conventional lime production (900 °C) as it bypasses limestone calcination, responsible for ~65% of the CO 2 emissions from the current process. Thus, the new process has a lower CO 2 footprint and enables the use of industrial waste heat. The mass and energy balances were quantified to reveal that increasing the calcium concentration of the feed solution and the precipitation temperature, decrease the energy demands of the RO step, thereby reducing the process’s overall CO 2 footprint. The pilot system operated continuously and achieved a production rate of nearly 1 kg per day of Ca(OH) 2 with a purity greater than 95 wt%. The average particle size of the precipitates depended on the residence time in the precipitation reactor, demonstrating an ability to produce size-controlled particulates. Importantly, the process achieved full water recirculation/reutilization level indicative of a low-consumable water demand. The outcomes offer new insights and understanding relevant to developing and upscaling low-CO 2 processes for cement, lime, and portlandite.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Neptunium redox speciation and determination of its total concentration in dissolved fuel simulant solutions by spectrophotometry

Here, two new approaches to measure Np concentration in dissolved used nuclear fuel simulant (aqueous feed for PUREX process) by spectrophotometry are developed. The first approach is based on chemical reduction of Np in the feed to its tetravalent state using ascorbic acid with simultaneous conversion of Pu(IV) to Pu(III). Interfering effects from light absorbing fission and corrosion products are accounted for by measuring optical absorbance spectrum of aqueous raffinate after extraction of U, Np, and Pu by tributyl phosphate in dodecane. The second approach uses no chemical treatment at all and relies on spontaneous valency adjustment of Np to Np(V) by dilution of the feed with water to reduce its acidity to low decimolar range of nitric acid concentration. Results of Np determination in the feed by spectrophotometry are in good agreement with its concentration measured by ICP-MS.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

April 2024 Semiannual Composite Salt Waste Processing Facility (SWPF) Decontaminated Salt Solution (DSS) Toxicity Characteristic Leaching Procedure (TCLP) Results

The aqueous waste from the Salt Waste Processing Facility (SWPF) is sampled semiannually for transfers to the Saltstone Production Facility (SPF). Salt solution is treated at SPF and disposed of in the Saltstone Disposal Facility (SDF). Per request of customer, X-TTR-Z-00027, Revision 0, one SDF waste form (saltstone) sample was prepared in the Savannah River National Laboratory (SRNL) from the SWPF Decontaminated Salt Solution (DSS) Waste Acceptance Criteria (WAC) sample and Z-area premix material for the April 2024 semiannual Toxicity Characteristic Leaching Procedure (TCLP) sample. The sample contained 60:40 (by weight) of slag and fly ash (referred to as the “Cement-Free grout sample”). Results from the technical report support Task 2: ‘Grout Leaching Analyses’ of the Task Technical Request (TTR) prepared by Savannah River Mission Completion (SRMC). After at least 28 days cured, a sample of the SDF waste form was collected and shipped to a certified laboratory for analysis using the Toxicity Characteristic Leaching Procedure (TCLP). The April 2024 semiannual Cement-Free grout sample met the South Carolina (SC) Code of Regulations for Hazardous Waste Management Regulations (HWMR) 61-79.261.24 and 61-79.268.48 requirements for a non-hazardous waste form with respect to the Resource Conservation and Recovery Act (RCRA) metals and Underlying Hazardous Constituents (UHCs), and met the SPF WAC that was in effect at the time of the tank sampling.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

October 2024 Semiannual Composite Salt Waste Processing Facility (SWPF) Decontaminated Salt Solution (DSS) Toxicity Characteristic Leaching Procedure (TCLP) Results

The aqueous waste from the Salt Waste Processing Facility (SWPF) is sampled semiannually for transfers to the Saltstone Production Facility (SPF). Salt solution is treated at SPF and disposed of in the Saltstone Disposal Facility (SDF). Per request of customer, X-TTR-Z-00027, Revision 0, one SDF waste form (saltstone) sample was prepared in the Savannah River National Laboratory (SRNL) from the SWPF Decontaminated Salt Solution (DSS) Waste Acceptance Criteria (WAC) sample and Z-area premix material for the October 2024 semiannual Toxicity Characteristic Leaching Procedure (TCLP) sample. The sample contained 60:40 (by weight) of slag and fly ash (referred to as the “Cement-Free grout sample”). Results from the technical report support Task 2: ‘Grout Leaching Analyses’ of the Task Technical Request (TTR) prepared by Savannah River Mission Completion (SRMC). At 64 days cured, a sample of the SDF waste form was collected and shipped to a certified laboratory for analysis using the Toxicity Characteristic Leaching Procedure (TCLP). The October 2024 semiannual Cement-Free grout sample met the South Carolina (SC) Code of Regulations for Hazardous Waste Management Regulations (HWMR) 61-79.261.24 and 61-79.268.48 requirements for a non-hazardous waste form with respect to the Resource Conservation and Recovery Act (RCRA) metals and Underlying Hazardous Constituents (UHCs), and met the SPF WAC that was in effect at the time of the sample collection at SWPF.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

April 2025 Semiannual Composite Salt Waste Processing Facility (SWPF) Decontaminated Salt Solution (DSS) Toxicity Characteristic Leaching Procedure (TCLP) Results

The aqueous waste from the Salt Waste Processing Facility is sampled semiannually for transfers to the Saltstone Production Facility. Salt solution is treated at the Saltstone Production Facility and disposed of in the Saltstone Disposal Facility. Per request of customer, X-TTR-Z-00027, Revision 0, one Saltstone Disposal Facility waste form was prepared at Savannah River National Laboratory using the Salt Waste Processing Facility Decontaminated Salt Solution and Z-area premix material for the April 2025 semiannual Toxicity Characteristic Leaching Procedure sample. The sample contained 60:40 (by weight) of slag and fly ash (referred to as the “Cement-Free grout sample”). Results from the technical report support Task 2: ‘Grout Leaching Analyses’ of the Task Technical Request prepared by Savannah River Mission Completion. At 43 days cured, the Saltstone sample was collected and shipped to a certified laboratory for analysis using the Toxicity Characteristic Leaching Procedure. The April 2025 semiannual Cement-Free grout sample met the South Carolina Code of Regulations for Hazardous Waste Management Regulations 61-79.261.24 and 61-79.268.48 requirements for a non-hazardous waste form with respect to the Resource Conservation and Recovery Act metals and Underlying Hazardous Constituents, and met the Saltstone Production Facility Waste Acceptance Criteria that was in effect at the time of the sample collection at the Salt Waste Processing Facility.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Analyzing the upscaling potential and geospatial siting of calcination-free calcium hydroxide production in the United States

This study evaluates the techno-economic feasibility and the embodied carbon dioxide intensity (eCI) of a novel process for producing nominally pure (>95 mass %) calcium hydroxide without the need for the thermal calcination of limestone. The process relies on the aqueous extraction of calcium from alkaline industrial wastes following which portlandite (Ca(OH) 2 : CH, a.k.a. slaked lime or hydrated lime) is precipitated by application of a waste-heat based thermal swing. This approach takes advantage of the temperature dependent solubility of CH at ambient pressure. We evaluated the feasibility of implementing this process in the U.S. based on the geospatial availability of waste heat and slags as a Ca-source. For the base case, the cost of production of “Low-Temperature Portlandite (LTP)” is 2-to-3 times that of traditional portlandite (~$180/tonne). The main driver of cost is the electricity demand for reverse osmosis (RO) which is used to concentrate Ca-ions in solution, and the costs of membrane replacement. Our sensitivity analysis showed that parity with the cost of production of traditional portlandite is readily achievable by selecting membranes with better durability (i.e., better pH resistance) and flux (i.e., higher permeability) without sacrificing selectivity. Significantly, LTP features an eCI that is between 40%- and - 80 % lower than its traditional counterpart when electricity is sourced from natural gas combustion or wind power, respectively. Finally, our geospatial analysis reveals that there are three areas in the U.S. with the potential for implementation of industrial-scale facilities that could produce at least 50 tonnes of pure Ca(OH) 2 per day, while achieving a production cost of ~$270 per tonne of Ca(OH) 2 , owing to the proximity between slag feedstocks and waste heat sources.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Vitrification of Hanford Tank Waste 241-AP-105 in a Continuous Laboratory-Scale Melter

Low-activity waste (LAW) stored in underground tanks on the Hanford site in Washington State is planned to be filtered for solids removal and processed through ion exchange columns for cesium removal at the Low-Activity Waste Pretreatment System facility. These pretreatment steps will allow the waste to be transferred to the Hanford Tank Waste Treatment and Immobilization Plant LAW facility for immobilization into glass. The liquid waste will be combined with glass-forming chemicals (GFCs) to form a waste feed slurry that can be fed to electric melters for vitrification. The process of continuously converting the aqueous feed slurry into a melt is dynamic and includes multiple reactions, degassing, and dissolution processes that depend on heat from the melt below. In this conversion process, waste components are partitioned into one of two streams: glass and off-gas. Processing information and chemical information associated with these waste product streams has been requested by Washington River Protection Solutions for actual tank waste from tank 241-AP-105 (referred to as AP-105). To acquire this type of information, a small-scale melter system was desired that would not require high volumes of input waste or the large resource commitment of a full-scale melter system, while also providing dynamic information that would be difficult to determine from batch reactions in a crucible system. A continuous laboratory-scale melter (CLSM), has been designed to operate with a continuous feeding process, while periodically pouring glass product and collecting off-gas. The CLSM vessel has been sized to collect the relevant process and chemical information from obtainable volumes of AP-105 waste samples. Two CLSMs were constructed: one in a non-radioactive environment for processing waste simulants and another in a fume hood capable of handling radioactive material for processing actual Hanford tank waste. This dual-system setup allowed for comparison between simulated and real tank waste with essentially identical test equipment. AP-105 waste simulant was first tested in the non-radioactive CLSM to determine the processability and desired operating window for the actual tank waste. Rhenium (Re) was added to the simulant to act as a surrogate for technetium-99 ( 99 Tc), a key waste component found in the actual tank waste. The partitioning of Re into the glass and off-gas products during the continuous feeding of simulant was determined, which allowed the Re retention, the mass flow rate of Re out of the CLSM via the glass product with respect to the mass flow rate of Re into the CLSM via the feed slurry, to be calculated. Key processing results and the average Re retention, from the CLSM test run with AP-105 simulant feed slurry are shown in Table ES.1.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Vitrification of Hanford Tank Waste 241-AP-107 in a Continuous Laboratory-Scale Melter

Low-activity waste (LAW) stored in underground tanks on the Hanford Site in Washington State is planned to be filtered for solids removal and processed through ion exchange columns for cesium removal. These pretreatment steps will allow the waste to be transferred to the Hanford Tank Waste Treatment and Immobilization Plant’s LAW Facility for immobilization into glass. The liquid waste will be combined with glass-forming chemicals (GFCs) to form a waste feed slurry that can be fed to electric melters for vitrification. The process of continuously converting the aqueous feed slurry into a melt is dynamic and includes multiple reactions, degassing, and dissolution processes that depend on heat from the melt below. In this conversion process, waste components are partitioned into one of two streams: glass and off-gas. Washington River Protection Solutions has requested processing information and chemical information associated with these waste products for actual waste from Hanford tank 241-AP-107 (referred to herein as AP-107). To acquire this type of information, a small-scale melter system was designed that would not require high volumes of input waste or the large resource commitment of a full-scale melter system, while also providing dynamic information that would be difficult to determine from batch reactions in a crucible system. A continuous laboratory-scale melter (CLSM) has been designed to operate with a continuous feeding process while periodically pouring glass product and collecting off-gas. The CLSM vessel has been sized to collect the relevant process and chemical information from obtainable volumes of AP-107 waste samples. A total 8.6 L of actual AP-107 tank waste were received after filtering for solids removal and ion exchange for cesium removal. This volume of AP-107 waste was mixed with GFCs to form an estimated 11.8 L of melter feed slurry. A mass of 7.01 kg of glass product were poured from the CLSM vessel during 10.07 hours of charging the AP-107 melter feed, indicating that about 15.0 kg of melter feed was vitrified into glass. The CLSM system was also designed with the capability to fully divert the flow of off-gas produced in the CLSM vessel to a sampling line that could capture the volatile species of interest, such as technetium-99 ( 99 Tc). This novel sampling system avoided the difficulties of slipstream sampling and could be activated once the feeding reached a steady state within the CLSM vessel. Off-gas product samples captured via high-efficiency particulate air (HEPA) filters using this method, as well as selected glass product samples were sent to an analytical lab for chemical analysis.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Application of Modular Design in Abatement of Fuel Element Debris (FED) Liquid Waste Stream - 16635

This paper provides a description of the processes applied within the Aqueous Discharge Abatement Plant (ADAP) at Bradwell nuclear power plant in the UK. This incorporates the Fuel Element Debris (FED) abatement plant and the Modular Active Effluent Treatment Plant (MAETP). These plants are housed in adjacent, but separate, structures and are inter-linked and share common services and control systems. The FED abatement plant, which has a shorter mission than MAETP, can be removed for decommissioning or redeployment without any impact to MAETP operation. ADAP treats aqueous waste streams generated during the ongoing decontamination and decommissioning (D and D) operations for release from the Bradwell Power Station. The plant is designed to receive and treat two major classes of liquids: 1. Slightly contaminated water from various D and D sources and collected rainwater from the power station, referred to as Aqueous Effluent (AE). 2. Dissolved fuel element debris solution. This comprises of contaminated magnesium alloy (generated during the stripping of external structures from spent Magnox fuel elements prior to shipment for reprocessing) which has been dissolved in nitric acid. All received wastes are treated to remove heavy metals and radioactive constituents prior to isolation, sampling, verification, and ultimately release to the Blackwater Estuary. The treatment consists of multiple processes including precipitation, filtration, adsorption and ion exchange carefully designed to remove targeted radionuclides and heavy metals. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗