Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “approach temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Control of large thermal distortions in a cryogenic wind tunnel

The National Transonic Facility (NTF) is a research wind tunnel capable of operation at temperatures down to 89K (160 R) and pressures up to 900,000 Pa (9 atmospheres) to achieve Reynolds numbers approaching 120,000,000. Wide temperature excursions combined with the precise alignment requirements of the tunnel aerodynamic surfaces imposed constraints on the mechanisms supporting the internal structures of the tunnel. The material selections suitable for this application were also limited. A general design philosophy of utilizing a single fixed point for each linear degree of freedom and guiding the expansion as required was adopted. These support systems allow thermal expansion to take place in a manner that minimizes the development of thermally induced stresses while maintaining structural alignment and resisting high aerodynamic loads. Typical of the support mechanisms are the preload brackets used in the fan shroud system and the Watts linkage used to support the upstream nacelle. The design of these mechanisms along with the basic design requirements and the constraints imposed by the tunnel system are discussed.

Gustafson, J. C.↗

Time resolved simulation of lightning by LIP

Results of time-resolved spectra of lightning simulation in air by laser-induced plasma (LIP) are reported. The measured electron temperatures varied from 17,000 +/-1000 K at 600 ns to 12,000 +/-1000 K at 4 microsec after the ignition of the plasma. Electron densities in the plasma varied from (7.0 +/-1.4) x 10 exp 17/cu cm to (9.0 +/-1.8) x 10 exp 16/cu cm for the above times. A comparison of state variables for LIP and natural lightning is presented. Immediately following the ignition, both natural lightning and LIP are found to reach temperatures in excess of 16,000 K and relax to ambient pressure with different rates. They are expected to approach the 2000-4000-K temperature range, which is important to chemical synthesis, in an asymptotically similar fashion.

Jebens, D. S.↗

Shadowgraph Study of Gradient Driven Fluctuations

A fluid or fluid mixture, subjected to a vertical temperature and/or concentration gradient in a gravitational field, exhibits greatly enhanced light scattering at small angles. This effect is caused by coupling between the vertical velocity fluctuations due to thermal energy and the vertically varying refractive index. Physically, small upward or downward moving regions will be displaced into fluid having a refractive index different from that of the moving region, thus giving rise to the enhanced scattering. The scattered intensity is predicted to vary with scattering wave vector q, as q(sup -4), for sufficiently large q, but the divergence is quenched by gravity at small q. In the absence of gravity, the long wavelength fluctuations responsible for the enhanced scattering are predicted to grow until limited by the sample dimensions. It is thus of interest to measure the mean-squared amplitude of such fluctuations in the microgravity environment for comparison with existing theory and ground based measurements. The relevant wave vectors are extremely small, making traditional low-angle light scattering difficult or impossible because of stray elastically scattered light generated by optical surfaces. An alternative technique is offered by the shadowgraph method, which is normally used to visualize fluid flows, but which can also serve as a quantitative tool to measure fluctuations. A somewhat novel shadowgraph apparatus and the necessary data analysis methods will be described. The apparatus uses a spatially coherent, but temporally incoherent, light source consisting of a super-luminescent diode coupled to a single-mode optical fiber in order to achieve extremely high spatial resolution, while avoiding effects caused by interference of light reflected from the various optical surfaces that are present when using laser sources. Results obtained for a critical mixture of aniline and cyclohexane subjected to a vertical temperature gradient will be presented. The sample was confined between two horizontal parallel sapphire plates with a vertical spacing of 1 mm. The temperatures of the sapphire plates were controlled by independent circulating water loops that used Peltier devices to add or remove heat from the room air as required. For a mixture with a temperature gradient, two effects are involved in generating the vertical refractive index gradient, namely thermal expansion and the Soret effect, which generates a concentration gradient in response to the applied temperature gradient. For the aniline/cyclohexane system, the denser component (aniline) migrates toward the colder surface. Consequently, when heating from above, both effects result in the sample density decreasing with altitude and are stabilizing in the sense that no convective motion occurs regardless of the magnitude of the applied temperature gradient. The Soret effect is strong near a binary liquid critical point, and thus the dominant effect is due to the induced concentration gradient. The results clearly show the divergence at low q and the predicted gravitational quenching. Results obtained for different applied temperature gradients at varying temperature differences from the critical temperature, clearly demonstrate the predicted divergence of the thermal diffusion ratio. Thus, the more closely the critical point is approached, the smaller becomes the temperature gradient required to generate the same signal. Two different methods have been used to generate pure concentration gradients. In the first, a sample cell was filled with a single fluid, ethylene glycol, and a denser miscible fluid, water, was added from below thus establishing a sharp interface to begin the experiment. As time went on the two fluids diffused into each other, and large amplitude fluctuations were clearly observed at low q. The effects of gravitational quenching were also evident. In the second method, the aniline/cyclohexane sample was used, and after applying a vertical temperature gradient for several hours, the top and bottom temperatures were set equal and the thermal gradient died on a time scale of seconds, leaving the Soret induced concentration gradient in place. Again, large-scale fluctuations were observed and died away slowly in amplitude as diffusion destroyed the initial concentration gradient.

Cannell, David↗

Intensified Warming and Aridity Accelerate Terminal Lake Desiccation in the Great Basin of the Western United States

Terminal lakes in the Great Basin (GB) of the western US host critical wildlife habitat and food for migrating birds and can be associated with serious human health and economic consequences when they desiccate. Water levels have declined dramatically in the last 100+ years due to diversion of inflows, drought and climate change. Satellite-derived environmental science data records (ESDRs) from the MODerate-resolution Imaging Spectroradiometer (MODIS) (snow cover, evapotranspiration (ET) and land surface temperature (LST)), enable a unique approach to evaluate the effects of aridification on terminal lakes and to study their individual vulnerabilities. Surface and air temperatures in the GB are rising dramatically, with a sharp rise in the rate of increase observed beginning around 2011, while the number of days of snow cover is declining especially in the western mountainous part of the GB as exemplified in Mono Basin, California. Rising temperatures coincide with fewer days of snow cover, a decrease of inflow to the lakes and greater evaporation of water from the lakes. MODIS ESDRs show strong and statistically significant increasing surface temperature (LST) in the GB, a reduction in the number of days of snow cover, and mixed results in ET. ET declined slightly in the more arid parts of the GB due to greater moisture restrictions to evaporation from extended drought, while ET increased in the more-vegetated, wetter, mountainous northeastern parts as temperatures have risen. Severe and costly ecological, human health and economic consequences are expected if the lakes continue to decline as predicted.

land surface temperature↗

Improved Regression Analysis of Temperature-Dependent Strain-Gage Balance Calibration Data

An improved approach is discussed that may be used to directly include first and second order temperature effects in the load prediction algorithm of a wind tunnel strain-gage balance. The improved approach was designed for the Iterative Method that fits strain-gage outputs as a function of calibration loads and uses a load iteration scheme during the wind tunnel test to predict loads from measured gage outputs. The improved approach assumes that the strain-gage balance is at a constant uniform temperature when it is calibrated and used. First, the method introduces a new independent variable for the regression analysis of the balance calibration data. The new variable is designed as the difference between the uniform temperature of the balance and a global reference temperature. This reference temperature should be the primary calibration temperature of the balance so that, if needed, a tare load iteration can be performed. Then, two temperature{dependent terms are included in the regression models of the gage outputs. They are the temperature difference itself and the square of the temperature difference. Simulated temperature{dependent data obtained from Triumph Aerospace's 2013 calibration of NASA's ARC-30K five component semi{span balance is used to illustrate the application of the improved approach.

wind tunnel testing↗

A review of processable high temperature resistant addition-type laminating resins

An important finding that resulted from research that was conducted to develop improved ablative resins was the discovery of a novel approach to synthesize processable high temperature resistant polymers. Low molecular weight polyimide prepolymers end-capped with norbornene groups were polymerized into thermo-oxidatively stable modified polyimides without the evolution of void producing volatile materials. This paper reviews basic studies that were performed using model compounds to elucidate the polymerization mechanism of the so-called addition-type polyimides. The fabrication and properties of polyimide/graphite fiber composites using A-type polyimide prepolymer as the matrix are described. An alternate method for preparing processable A-type polyimides by means of in situ polymerization of monomeric reactants on the fiber reinforcement is also described. Polyimide/graphite fiber composite performance at elevated temperatures is presented for A-type polyimides.

Serafini, T. T.↗

Resonance scattering from interstellar and interplanetary helium.

The intensity and spatial distribution of the diffuse 584 A glow due to resonance scattering of solar He I, 584 A line radiation by neutral interstellar and interplanetary helium is derived. Two sources of neutral helium are considered: the local interstellar medium interacting with the solar system and dust deionization of the He(++) component of the solar wind. Which of these two sources will dominate the radiation field at 1 AU is dependent upon a number of parameters which have not yet been determined. Results are presented as a function of the width of the solar line, and the temperature and speed of approach of the interstellar medium. The calculated intensities for the most extreme cases vary from approximately .000001 Rayleighs to almost 100 Rayleighs. The relevance of these results to the study of the interplanetary and interstellar medium is discussed.

Paresce, F.↗

Meteorological radar calibration

A meteorological radar calibration technique is developed. It is found that the integrated, range corrected, received power saturates under intense rain conditions in a manner analogous to that encountered for the radiometric path temperature. Furthermore, it is found that this saturation condition establishes a bound which may be used to determine an absolution radar calibration for the case of radars operating at attenuating wavelengths. In the case of less intense rainfall or for radars at nonattenuating wavelengths, the relationship for direct calibration in terms of an independent measurement of radiometric path temperature is developed. This approach offers the advantage that the calibration is in terms of an independent measurement of the rainfall through the same elevated region as that viewed by the radar.

Hodge, D. B.↗

Elevated-temperature effects on strain gages on the YF-12A wing

A general study is made of the effects of structural heating on calibrated-strain-gage load measurements on the wing of a supersonic airplane. The primary emphasis is on temperature-induced effects as they relate to slope changes and thermal shifts of the applied load/strain relationships. These effects are studied by using the YF-12A airplane, a structural computer model, and subsequent analyses. Such topics as the thermal environment of the structure, the variation of load paths at elevated temperature, the thermal response characteristics of load equations, elevated-temperature load-measurement approaches, the thermal calibration of wings, and the correlation of strains are discussed. Ways are suggested to measure loads with calibrated strain gages in the supersonic environment.

Jenkins, J. M.↗

Evaluation of the Doraiswamy-Thompson winter wheat crop calendar model incorporating a modified spring restart sequence

The Robertson phenology was used to provide growth stage information to a wheat stress indicator mode. A stress indicator model demands two acurate predictions from a crop calendar: date of spring growth initiation; and crop calendar stage at growth initiation. Several approaches for restarting the Robertson phenology model at spring growth initiation were studied. Although best results were obtained with a solar thermal unit method, an alternate approach which indicates soil temperature as the controlling parameter for spring growth initiation was selected and tested. The modified model (Doraiswamy-Thompson) is compared to LACIE-Robertson model predictions.

Taylor, T. W.↗

The structure of the Ionian lithosphere

Exploratory work on the structure of the Ionian lithosphere is reported. The approach is to examine temperature profiles within the lithosphere that result from different distributions of sulfur and silicates and different conductive heat fluxes, then compare such profiles with observations in the expectation that only a limited set of the profiles are possible. In this preliminary work some rather simplistic assumptions were taken and the report should be viewed more as a demonstration of a method rather than a presentation of results.

Carr, M. H.↗

Detection of the response of ozone in the middle atmosphere to short-term solar ultraviolet variations

The response of ozone to solar UV variation is determined in the middle atmosphere between the heights of 10 and 0.2 mb. The definitive isolation of the smaller variations associated with short-term solar variability is accomplished only after removal of the larger changes of ozone related to temperature variations. Using this approach the correlation coefficients between detrended ozone (Nimbus 7 LIMS) and short-term 205 nm solar variation (Nimbus 7 SBUV) are found to be much higher (0.9) than achieved in previous studies. The theoretical response time and amplitude of response of ozone in the middle atmosphere to observed short-term solar UV variations is found to be in good agreement with observations, except near 0.2 mb. The corresponding long-term response over the solar cycle is also estimated.

Keating, G. M.↗

Variable thermal properties and thermal relaxation time in hyperbolic heat conduction

Numerical solutions were obtained for a finite slab with an applied surface heat flux at one boundary using both the hyperbolic (MacCormack's method) and parabolic (Crank-Nicolson method) heat conduction equations. The effects on the temperature distributions of varying density, specific heat, and thermal relaxation time were calculated. Each of these properties had an effect on the thermal front velocity (in the hyperbolic solution) as well as the temperatures in the medium. In the hyperbolic solutions, as the density or specific heat decreased with temperature, both the temperatures within the medium and the thermal front velocity increased. The value taken for the thermal relaxation time was found to determine the 'hyperbolicity' of the heat conduction model. The use of a time dependent relaxation time allowed for solutions where the thermal energy propagated as a high temperature wave initially, but approached a diffusion process more rapidly than was possible with a constant large relaxation time.

Glass, David E.↗

Filament wound metal lined propellant tanks for future Earth-to-orbit transports

For future Earth-to-orbit transport vehicles, reusability and lighter weights are sought for the main propellant tanks. To achieve this, a filament wound tank with a metal liner and an intermediate layer of foam-filled honeycomb is proposed. A hydrogen tank is used as an example. To accommodate mismatches in the expansion of liner and overwrap a design is proposed wherin the liner is configured so that the extension of the liner under pressure matches the expected contraction of the same liner due to the presence of a cryogen. In operation, the liner is pressurized at a rate such that the pressure strain matches the contraction due to decrease in temperature. As an alternate approach, compressive pre-stress is placed in the liner such that it will not separate from the overwrap. A finite element program is used to show stresses in the liner and overwrap for various tank pressures for the pre-stressed liner concept. A fracture mechanics analysis is made of the liners to determine tank life. The tank concept shown has a similar weight to the Shuttle external hydrogen tank, but the filament wound tank is expected to be reusable. Integration of the propellant tanks into a future transport vehicle is discussed.

Macconochie, Ian O.↗

Practical approaches for application of resistance type strain gages on high temperature composites

Four major areas of interest with respect to utilizing strain gages on carbon/carbon (with SiC surfaces) and titanium matrix composites are addressed. Strain gage and adhesive combinations on carbon/carbon (C/C) at temperatures from minus 190 C to to 540 C, half-bridge gaging for reducing apparent strain on C/C using Poisson's ratio and bending configurations, a review of the 'field installation' techniques developed for gaging a C/C hypersonic generic elevon, and results of initial strain gaging efforts on titanium matrix composites are discussed. Current research in developing techniques for increasing the maximum temperature for strain gages on carbon/carbon are reviewed.

Moore, Thomas C., Sr.↗