Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “analytical methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Aircraft motion analysis using limited flight and radar data

The development and application of methods for reconstructing, from a limited set of recorded data, a comprehensive scenario of aircraft motions before and during an accident are described. The accuracy of these analytical methods is investigated using data recorded onboard the Ames CV-990 research aircraft. In these experiments, the expanded set of data, derived from either foil or ATC records, is compared with corresponding values measured by the research instrumentation system onboard the aircraft. The results indicate that many of the derived quantities are in good agreement with the corresponding onboard measurements. A recent application of this procedure using actual accident records is presented and potential applications are briefly reviewed.

Wingrove, R. C.↗
NASA NTRS1980

The impact of pulsed RFI on the coded BER performance of the nonlinear satellite communication channel

Communication links from low orbiting spacecraft to a central ground station, via satellite repeater, may be susceptible to significant performance degradation if high-level, pulsed radio frequency interference (RFI) must be contended with. The present paper examines the coded bit error rate (BER) performance of a communication system in which BPSK modulation is employed, pulsed CW or pulsed noise RFI is present, and the transponder contains a nonlinearity characterized by arbitrary AM/AM and AM/PM characteristics. A major result of this paper is an analytic method for determining soft decision statistics of the receiver demodulator output, in which pulsed RFI effects are accounted for. It is demonstrated that this result can be analytically applied to the approximate determination of the BER at the output of a Viterbi decoder, when convolutional coding is employed.

Weinberg, A.↗
NASA NTRS1990

Nonlinear analysis of compressively loaded linked-plate structures

A method is presented for the geometrically nonlinear analysis of the equilibrium behavior of a general class of compressively loaded, prismatic, linked-plate structures. The semi-analytical method accounts for geometric shape imperfections, and allows the use of laminated composite plate properties. Buckling eigenfunctions are used as displacement shape functions, and the associated second-order displacement fields are incorporated. The nonlinear plate equilibrium equations are expressed in terms of the assumed displacement form, and the Galerkin method is used to obtain a set of algebraic equations which are nonlinear in the modal amplitudes and the load parameter. Buckling eigensolutions for the class of structures under consideration can be obtained from the VIPASA computer code; thus, subject to some additional restrictions in loading and plate anisotropy, structural configurations which can be analyzed with regard to buckling response by VIPASA can be analyzed with regard to geometrically nonlinear response using the new method.

Stoll, Frederick↗
NASA NTRS1999

Development of Advanced In-Cylinder Components and Tribological Systems for Low Heat Rejection Diesel Engines

In-cylinder components and tribological system concepts were designed, fabricated and tested at conditions anticipated for a 55% thermal efficiency heavy duty diesel engine for the year 2000 and beyond. A Cummins L10 single cylinder research engine was used to evaluate a spherical joint piston and connecting rod with 19.3 MPa (2800 psi) peak cylinder pressure capability, a thermal fatigue resistant insulated cylinder head, radial combustion seal cylinder liners, a highly compliant steel top compression ring, a variable geometry turbocharger, and a microwave heated particulate trap. Components successfully demonstrated in the final test included spherical joint connecting rod with a fiber reinforced piston, high conformability steel top rings with wear resistant coatings, ceramic exhaust ports with strategic oil cooling and radial combustion seal cylinder liner with cooling jacket transfer fins. A Cummins 6B diesel was used to develop the analytical methods, materials, manufacturing technology and engine components for lighter weight diesel engines without sacrificing performance or durability. A 6B diesel engine was built and tested to calibrate analytical models for the aluminum cylinder head and aluminum block.

Yonushonis, T. M.↗
NASA NTRS2008

A Modeling Technique and Representation of Failure in the Analysis of Triaxial Braided Carbon Fiber Composites

Quasi-static tests have been performed on triaxially braided carbon fiber composite materials with large unit cell sizes. The effects of different fibers and matrix materials on the failure mode were investigated. Simulations of the tests have been performed using the transient dynamic finite element code, LS-DYNA. However, the wide range of failure modes observed for the triaxial braided carbon fiber composites during tests could not be simulated using composite material models currently available within LS-DYNA. A macroscopic approach has been developed that provides better simulation of the material response in these materials. This approach uses full-field optical measurement techniques to measure local failures during quasi-static testing. Information from these experiments is then used along with the current material models available in LS-DYNA to simulate the influence of the braided architecture on the failure process. This method uses two-dimensional shell elements with integration points through the thickness of the elements to represent the different layers of braid along with a new analytical method for the import of material stiffness and failure data directly. The present method is being used to examine the effect of material properties on the failure process. The experimental approaches used to obtain the required data will be described, and preliminary results of the numerical analysis will be presented.

Littell, Justin D.↗
NASA NTRS2008

A Modeling Technique and Representation of Failure in the Analysis of Triaxial Braided Carbon Fiber Composites

Quasi-static tests have been performed on triaxially braided carbon fiber composite materials with large unit cell sizes. The effects of different fibers and matrix materials on the failure mode were investigated. Simulations of the tests have been performed using the transient dynamic finite element code, LS-DYNA. However, the wide range of failure modes observed for the triaxial braided carbon fiber composites during tests could not be simulated using composite material models currently available within LS-DYNA. A macroscopic approach has been developed that provides better simulation of the material response in these materials. This approach uses full-field optical measurement techniques to measure local failures during quasi-static testing. Information from these experiments is then used along with the current material models available in LS-DYNA to simulate the influence of the braided architecture on the failure process. This method uses two-dimensional shell elements with integration points through the thickness of the elements to represent the different layers of braid along with a new analytical method for the import of material stiffness and failure data directly. The present method is being used to examine the effect of material properties on the failure process. The experimental approaches used to obtain the required data will be described, and preliminary results of the numerical analysis will be presented.

Littell, Justin D.↗
NASA NTRS2017

A Fast, Accurate and Sensitive GC-FID Method for the Analyses of Glycols in Water and Urine

Glycols, specifically ethylene glycol and 1,2-propanediol, are some of the major organic compounds found in the humidity condensate samples collected on the International Space Station. The current analytical method for glycols is a GC/MS method with direct sample injection. This method is simple and fast, but it is not very sensitive. Reporting limits for ethylene glycol and 1,2-propanediol are only 1 ppm. A much more sensitive GC/FID method was developed, in which glycols were derivatized with benzoyl chloride for 10 minutes before being extracted with hexane. Using 1,3-propanediol as an internal standard, the detection limits for the GC/FID method was determined to be 50 ppb and the analysis only takes 7 minutes. Data from the GC/MS and the new GC/FID methods shows excellent agreement with each other. Factors affecting the sensitivity, including sample volume, NaOH concentration and volume, volume of benzoyl chloride, reaction time and temperature, were investigated. Interferences during derivatization and possible method to reduce interferences were also investigated.

Kuo, C. Mike↗
NASA NTRS1973

Analytic and experimental performance of two isentropic mixed compression axisymmetric inlets at Mach numbers 0.8 to 2.65

A mixed compression axisymmetric inlet model with a capture diameter of 50 cm was tested at Mach numbers ranging from 0.8 to 2.65 at 0 deg angle of attack and a constant total pressure of approximately 1 atm. Analytical methods accounting for the effects of both viscous and inviscid flows and incorporating empirical bleed discharge coefficients were used in the procedure for designing the inlet contours and the bleed system. Experimental results are compared with analytic predictions and are also compared with results from earlier tests of an inlet with the same internal contours but with a bleed system developed by cut and try methods in the wind tunnel. With the bleed configuration predicted by the design procedure, maximum total pressure recovery at the engine face at the design Mach number of 2.65 was 93 percent, with a total pressure distortion less than 10 percent. Corresponding bleed mass flow was approximately 7.5 percent, which was about 1.3 percent less than predicted. At lower supersonic Mach numbers, pressure recovery and bleed were generally lower and distortion generally higher.

Smeltzer, D. B.↗
NASA NTRS1977

Application of perturbation methods to improve analytical model correlation with test data

A linear perturbation method developed by White (1972) to improve the correlation between analytical models and experimental data is applied to modeling of the Viking Propulsion Subsystem (VPS), flown successfully as part of the Viking Spacecraft launch of 1975. Analytical models and modal test data developed for the VPS are employed in the application; a set of mathematically generated data and a corresponding perturbed analytical model, representative of actual flight hardware, are also subjected to the White method. It is found that the linear perturbation method does not yield a single unique improved model.

Garba, J. A.↗
NASA NTRS1988

Summary of analytical model improvement method and related technology

The research project which resulted in the AMI (Analytical Model Improvement) method was funded by the Langley Research Center from 1979 through 1985. The objective was to develop a method for obtaining improved dynamic models of structures by using both test data and numerical analysis. The research was successfully performed and the method was applied to a real structure having a realistic NASTRAN model with over 500 degrees of freedom. The method and its application are briefly discussed as well as other indirect benefits in related technical areas.

Berman, Alex↗
NASA NTRS1996

Minimum Weight Design of a Generic Axisymmetric Inlet

A new minimum weight design method for high-speed axisymmetric inlets was demonstrated on a generic inlet. The method uses Classical Beam Theory and shell buckling to determine the minimum required equivalent isotropic thickness for a stiffened shell based on prescribed structural design requirements and load conditions. The optimum spacing and equivalent isotropic thickness of ring frame supports are computed to prevent buckling. The method thus develops a preliminary structural design for the inlet and computes the structural weight. Finite element analyses were performed on the resulting inlet design to evaluate the analytical results. Comparisons between the analytical and finite element stresses and deflections identified areas needing improvement in the analytical method. The addition of the deflection due to shear and a torsional buckling failure mode to the new method brought its results in line with those from the finite element analyses. Final validation of the new method will be made using data from actual inlets.

Nadell, Shari-Beth↗
NASA NTRSDate not supplied

Verifying Autonomous Air Traffic Algorithms in the Presence of Sensor Error and Flight Perturbations

We offer a method to verify algorithms for air traffic control in the presence of sensor errors and flight perturbations. Since errors and perturbations are described by stochastic processes, verification by analytical methods is difficult. We turn to Monte Carlo simulation, but there are two major obstacles. Since air traffic algorithms are safety-critical, the algorithm must be established at a very high confidence level which requires an enormous number of trials. Another is that a simulation attempts to show that an algorithm correctly handles a hazard that might appear, but there is a lack of information about the frequency of occurrence of hazards in the airspace. This paper offers a solution to these and other obstacles. It recognizes there may be a number of algorithms that address different hazards, and the results of the different simulations must be combined to satisfy a global reliability requirement at a high confidence level. To demonstrate the feasibility of the approach, we apply it to an example, an initial effort in collision avoidance.

verification↗
NASA NTRS1985

Application of the finite element method in the calculation of transmission loss of flat and curved panels

This investigation represents an extension of a study of Roussos (1985) who considered the noise transmission loss of a rectangular plate in an infinite baffle. Roussos, who employed an analytical formulation, considered an unstiffened plate. While it is difficult to consider stiffeners by means of analytical methods, the difficulties can be avoided by employing a finite element procedure. For this reason, the present study is concerned with the implementation of a finite element method. The representation of the panel transmission loss is discussed, and the determination of the panel motion by means of the finite element technique is described, taking into account an isotropic flat panel, the exciting force, an eigenvalue problem, the radiation pressure, a plate element, and a cylindrical shell element. Numerical results are considered for a flat panel, a curved panel, and a stiffened flat panel.

Koval, L. R.↗
NASA NTRS2009

Advances in Adaptive Control Methods

This poster presentation describes recent advances in adaptive control technology developed by NASA. Optimal Control Modification is a novel adaptive law that can improve performance and robustness of adaptive control systems. A new technique has been developed to provide an analytical method for computing time delay stability margin for adaptive control systems.

Nguyen, Nhan↗
NASA NTRS1995

Consistent approach to describing aircraft HIRF protection

The high intensity radiated fields (HIRF) certification process as currently implemented is comprised of an inconsistent combination of factors that tend to emphasize worst case scenarios in assessing commercial airplane certification requirements. By examining these factors which include the process definition, the external HIRF environment, the aircraft coupling and corresponding internal fields, and methods of measuring equipment susceptibilities, activities leading to an approach to appraising airplane vulnerability to HIRF are proposed. This approach utilizes technically based criteria to evaluate the nature of the threat, including the probability of encountering the external HIRF environment. No single test or analytic method comprehensively addresses the full HIRF threat frequency spectrum. Additional tools such as statistical methods must be adopted to arrive at more realistic requirements to reflect commercial aircraft vulnerability to the HIRF threat. Test and analytic data are provided to support the conclusions of this report. This work was performed under NASA contract NAS1-19360, Task 52.

Rimbey, P. R.↗
NASA NTRS1981

Improved methods for fan sound field determination

Several methods for determining acoustic mode structure in aircraft turbofan engines using wall microphone data were studied. A method for reducing data was devised and implemented which makes the definition of discrete coherent sound fields measured in the presence of engine speed fluctuation more accurate. For the analytical methods, algorithms were developed to define the dominant circumferential modes from full and partial circumferential arrays of microphones. Axial arrays were explored to define mode structure as a function of cutoff ratio, and the use of data taken at several constant speeds was also evaluated in an attempt to reduce instrumentation requirements. Sensitivities of the various methods to microphone density, array size and measurement error were evaluated and results of these studies showed these new methods to be impractical. The data reduction method used to reduce the effects of engine speed variation consisted of an electronic circuit which windowed the data so that signal enhancement could occur only when the speed was within a narrow range.

Cicon, D. E.↗
NASA NTRS2002

Analysis of Graphite-Reinforced Cementitious Composites

Strategically embedding graphite meshes in a compliant cementitious matrix produces a composite material with relatively high tension and compressive properties as compared to steel-reinforced structures fabricated from a standard concrete mix. Although these composite systems are somewhat similar, the methods used to analyze steel-reinforced composites often fail to characterize the behavior of their more advanced graphite-reinforced counterparts. This Technical Memorandum describes some of the analytical methods being developed to determine the deflections and stresses in graphite-reinforced cementitious composites. It is initially demonstrated that the standard transform section method fails to provide accurate results when the elastic moduli ratio exceeds 20. An alternate approach is formulated by using the rule of mixtures to determine a set of effective material properties for the composite. Tensile tests are conducted on composite samples to verify this approach. When the effective material properties are used to characterize the deflections of composite beams subjected to pure bending, an excellent agreement is obtained. Laminated composite plate theory is investigated as a means for analyzing even more complex composites, consisting of multiple graphite layers oriented in different directions. In this case, composite beams are analyzed using the laminated composite plate theory with material properties established from tensile tests. Then, finite element modeling is used to verify the results. Considering the complexity of the samples, a very good agreement is obtained.

Vaughan, R. E.↗
NASA NTRS1979

Characteristics of propeller noise on an aircraft fuselage related to interior noise transmission

Exterior noise was measured on the fuselage of a twin-engine, light aircraft at four values of engine rpm in ground static tests and at forward speeds up to 36 m/s in taxi tests. Propeller noise levels, spectra, and correlations were determined using a horizontal array of seven flush-mounted microphones and a vertical array of four flush-mounted microphones in the propeller plane. The measured levels and spectra are compared with predictions based on empirical and analytical methods for static and taxi conditions. Trace wavelengths of the propeller noise field, obtained from point-to-point correlations, are compared with the aircraft sidewall structural dimensions, and some analytical results are presented that suggest the sensitivity of interior noise transmission to variations of the propeller noise characteristics.

Mixson, J. S.↗