Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “alternating minimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Dual-Fuel Ammonia Equivalence Ratio Sweep Data

Ammonia (NH3) has garnered significant interest as an alternative fuel for meeting international emissions reduction mandates in sectors with high weight and distance requirements, such as shipping. Technical barriers and unanswered questions remain on the combustion strategies that can maximize ammonia utilization and minimize emissions. Prior research studies at the US Department of Energy’s Oak Ridge National Laboratory have shown strong performance with NH3 under dual-fuel mode using conventional diesel combustion (CDC) manifold air pressure settings. Diesel airflow was initially used to simplify retrofitting (no turbocharger modification), which resulted in air-fuel equivalence ratios (λ) greater than 1.5. To characterize potential improvements in dual-fuel NH3 combustion performance at richer in-cylinder conditions, a global λ sweep compared the use of early (E-pilot) and late (L-pilot) single diesel injections. The experiments were conducted at 1200 RPM and 12.8 ± 0.2 bar (75 % load), and λ was varied by decreasing the commanded air flow to the engine at greater than 90 % ammonia energy substitution level. A diesel injection timing sweep was conducted for both the injection strategies at fixed λ, and the timing with the lowest engine-out N2O emissions was identified. The results indicated an optimal balance between CO2,eq and thermal efficiency benefits both E-pilot and L-pilot injection strategy cases compared with CDC at a λ of 1.4. The indicated nitrogen-based emissions exhibited a strong correlation to the ratio of CA5–50 and ignition delay for L-pilot, but no apparent trend emerged for the E-pilot injection strategy at the tested boundary conditions. This dataset includes the raw experimental data and documentation of the experiment conditions and methods.

30 DIRECT ENERGY CONVERSION↗
NASA NTRS1989

Mesh refinement in finite element analysis by minimization of the stiffness matrix trace

Most finite element packages provide means to generate meshes automatically. However, the user is usually confronted with the problem of not knowing whether the mesh generated is appropriate for the problem at hand. Since the accuracy of the finite element results is mesh dependent, mesh selection forms a very important step in the analysis. Indeed, in accurate analyses, meshes need to be refined or rezoned until the solution converges to a value so that the error is below a predetermined tolerance. A-posteriori methods use error indicators, developed by using the theory of interpolation and approximation theory, for mesh refinements. Some use other criterions, such as strain energy density variation and stress contours for example, to obtain near optimal meshes. Although these methods are adaptive, they are expensive. Alternatively, a priori methods, until now available, use geometrical parameters, for example, element aspect ratio. Therefore, they are not adaptive by nature. An adaptive a-priori method is developed. The criterion is that the minimization of the trace of the stiffness matrix with respect to the nodal coordinates, leads to a minimization of the potential energy, and as a consequence provide a good starting mesh. In a few examples the method is shown to provide the optimal mesh. The method is also shown to be relatively simple and amenable to development of computer algorithms. When the procedure is used in conjunction with a-posteriori methods of grid refinement, it is shown that fewer refinement iterations and fewer degrees of freedom are required for convergence as opposed to when the procedure is not used. The mesh obtained is shown to have uniform distribution of stiffness among the nodes and elements which, as a consequence, leads to uniform error distribution. Thus the mesh obtained meets the optimality criterion of uniform error distribution.

Kittur, Madan G.↗
DOE OSTI2026

Carbon monoxide oxidation expands the known metabolic capacity in anaerobic methanotrophic consortia

Consortia of anaerobic methane-oxidizing archaea (ANME-2) and sulphate-reducing bacteria (SRB) represent globally relevant syntrophic associations capable of growing with minimal amounts of free energy and can persist when methane becomes limiting. Carbon monoxide (CO) has been reported in seep environments and represents a thermodynamically favourable alternative electron donor due to its low reduction potential. Here, we show that environmental ANME-SRB consortia can oxidize CO in the absence of methane, in anoxic microcosm experiments using a combination of stable isotope geochemical tracers, metatranscriptomics, and single cell activity measurements (FISH–nanoSIMS). The oxidation of CO was coupled with sulphate-reduction by syntrophic consortia, and, in the absence of sulphate, through CO 2 reduction to methane by ANME-2. Under these conditions, the production of methane was one ninth the rate of methanotrophy coupled to sulphate-reduction. Paired single cell FISH-nanoSIMS analysis of anabolic activity indicates that CO respiration appears to support cell maintenance rather than active growth, consistent with the observed down-regulation of energy generating complexes in ANME (e.g., mtr, rnf, etc.). The versatile capability of CO oxidation by anaerobic methanotrophic consortia broadens our understanding of carbon cycling in methane seeps and highlights potential mechanisms of resilience by methanotrophic archaea under changing geochemical regimes.

03 NATURAL GAS↗
DOE OSTI2023

Origin of medium-range atomic correlation in simple liquids: Density wave theory

The atomic pair-distribution function of simple liquid and glass shows exponentially decaying oscillations beyond the first peak, representing the medium-range order (MRO). The structural coherence length that characterizes the exponential decay increases with decreasing temperature and freezes at the glass transition. Conventionally, the structure of liquid and glass is elucidated by focusing on a center atom and its neighboring atom shell characterized by the short-range order (SRO) and describing the global structure in terms of overlapping local clusters of atoms as building units. However, this local bottom-up approach fails to explain the strong drive to form the MRO, which is different in nature from the SRO. We propose to add an alternative top-down approach based upon the density wave theory. In this approach, one starts with a high-density gas state and seeks to minimize the global potential energy in reciprocal space through density waves using the pseudopotential. The local bottom-up and global top-down driving forces are not mutually compatible, and the competition and compromise between them result in a final structure with the MRO. This even-handed approach provides a more intuitive explanation of the structure of simple liquid and glass.

42 ENGINEERING↗
NASA NTRS1986

A new design concept for indraft wind-tunnel inlets with application to the National Full-Scale Aerodynamics Complex

The present inlet design concept for an indraft wind tunnel, which is especially suited to applications for which a specific test section flwo quality is required with minimum inlet size, employs a cascade or 'vaneset' to control flow at the inlet plane, so that test section total pressure variation is minimized. Potential flow panel methods, together with empirical pressure loss predictions, are used to predict inlet cascade performance. This concept has been used to develop an alternative inlet design for the 80 x 120-ft wind tunnel at NASA Ames Research Center. Experimental results show that a short length/diameter ratio wind tunnel inlet furnishing atmospheric wind isolation and uniform test section flow can be designed.

Ross, J. C.↗
NASA NTRS1986

A new design concept for indraft wind-tunnel inlets with application to the national full-scale aerodynamic complex

The present inlet design concept for an indraft wind tunnel, which is especially suited to applications for which a specific test section flow quality is required with minimum inlet size, employs a cascade or vaneset to control flow at the inlet plane, so that test section total pressure variation is minimized. Potential flow panel methods, together with empirical pressure loss predictions, are used to predict inlet cascade performance. This concept has been used to develop an alternative inlet design for the 80 x 120-ft wind tunnel at NASA Ames Research Center. Experimental results show that a short length/diameter ratio wind tunnel inlet furnishing atmospheric wind isolation and uniform test section flow can be designed.

Ross, James C.↗
NASA NTRS1987

Assessment of the COFSI/MAST I project

The COFS (MAST I) deployer/retractor assembly (DRA) which has a cluster of mechanisms that constitute the collapsible/extensible Mast, contains mechanisms/linkages that deploy and retract. The Mast is a flexible spatial (3D) linkage with hinges that lock into place during deployment to form a truss type structure. It is 60 meters long with repeating sections of two bays. Each bay has alternating diagonals. All joints are single degree-of-freedom hinges, arranged such that the Mast does not rotate during deployment/restow and that deformation energy is minimized. Mispan hinges are incorporated in the diagonals and half of the batten members. The various operational aspects and characteristics of the various mechanisms within the DRA are analyzed. In view of the disadvantages of statical in determinancy as well as the inefficiencies inherent in recirculating gear trains, it is recommended that the bevel gear trains and the bell-crank mechanisms be redesigned.

Chew, Meng-Sang↗
NASA NTRS2003

Collaboration of the NASA Glenn Research Center and Rolls-Royce Developed Thin Film Multilayered Dielectrics for Harsh Environments

The use of thin films to electrically insulate thin film sensors on engine components minimizes the intrusiveness of the sensors and allows a more accurate measurement of the environment. A variety of insulating films were investigated for preventing electrical shorting caused by insulator failure between the sensor and the component. By alternating layers of sputtered high-temperature ceramics, a sequence of insulating layers was devised that (1) prevents pinholes from forming completely through the insulator and (2) maintains high electrical resistivity at high temperatures. The total thickness is only a fraction of that needed for conventional insulating techniques. The Sensors and Electronics Technology Branch of the NASA Glenn Research Center has an in-house effort to develop thin film sensors for surface measurement in propulsion system research. Thin film sensors do not require special machining of the components on which they are mounted, and they are considerably thinner (less than 10 mm thick) than wire or foil sensors. The thin film sensors are thus much less disturbing to the operating environment and have a minimal impact on the physical characteristics of the supporting component. To further this research, NASA Glenn and Rolls-Royce (Derby, UK), with assistance from the Ohio Aerospace Institute (OAI) and the Akima Corporation, pursued a joint investigation using multilayered thin film dielectrics as a reliable insulator in harsh environments. The use of a multilayered scheme is thought to be promising for the fabrication of electrically insulating thin films. A major cause of conduction in thin film dielectrics is the presence of defects, such as pinholes, that propagate through the film to the underlying substrate surface. By alternating the insulating material, each new growth pattern would deviate from the previous one, eliminating direct pathways for conduction to the substrate. The film depositions and testing were conducted in the Instrument Research Laboratory at Glenn. The multilayered insulator test samples were made from alumina and stainless steel shims that were first covered with a sputtered underlayer of either yttria-stabilized zirconia or chromium carbide, and then overcoated with a sputtered top layer of alumina. An example of a test sample is shown in the following photograph. Each multilayered insulator sample was 5 mm thick, at least an order of magnitude thinner than conventional insulators. The insulating properties of the samples were tested in a high-temperature air oven to determine their suitability. The multilayer insulators tested showed a stabilized film at temperatures in excess of 800 C (1472 F). The underlying materials in these multilayers allow thermal expansion stresses produced during the heating to be graded. The chromium carbide-alumina multilayer had the best adhesion at high temperatures, presumably from the induced chemical bonding between the substrate and the chromium carbide underlayer. However, the zirconia-alumina multilayer proved to have slightly better insulating properties when adhering. The application of the zirconia-alumina insulator has been demonstrated on a nickel-alloy fan blade, as shown. The insulators using thin film sensors still need to be tested in a relevant high-temperature combustion environment.

Wrbanek, John D.↗
DOE OSTI2025

OC7 phase I: Toward practical sea-state-dependent modeling of hydrodynamic viscous drag and damping

Here, this article presents a collaborative research campaign under the OC7 project on refining the engineering modeling approach for hydrodynamic viscous drag and damping on floating wind platforms, focusing on the adjustment of hydrodynamic drag and damping coefficients for different sea states. The participant simulation results show significant improvements over the previous OC6 project in predicting the low-frequency resonance motion under nonoperational conditions. The improvements are mainly due to enhanced modeling, including the adoption of wave stretching, and directly tuning the coefficients to measured platform motion in waves instead of free decay. For accurate predictions of mean- and slow-drift motion, the better performing models use a decreasing column splash zone drag coefficient and increasing surge damping/drag with increasing wave height. The model tuning for heave and pitch resonance shows less consistency. Generally, both quadratic drag and additional heave or pitch damping are needed for accurate predictions. Alternatively, a quadratic drag formulation with velocity filtering for the rectangular pontoons leads to improved predictions without additional damping. This model is also potentially more predictive, requiring minimal adjustment to its parameters for different conditions.

17 WIND ENERGY↗
DOE OSTI2022

Colossal barocaloric effects with ultralow hysteresis in two-dimensional metal–halide perovskites

Pressure-induced thermal changes in solids—barocaloric effects—can be used to drive cooling cycles that offer a promising alternative to traditional vapor-compression technologies. Efficient barocaloric cooling requires materials that undergo reversible phase transitions with large entropy changes, high sensitivity to hydrostatic pressure, and minimal hysteresis, the combination of which has been challenging to achieve in existing barocaloric materials. Here, we report a new mechanism for achieving colossal barocaloric effects that leverages the large volume and conformational entropy changes of hydrocarbon order–disorder transitions within the organic bilayers of select two-dimensional metal–halide perovskites. Significantly, we show how the confined nature of these order–disorder phase transitions and the synthetic tunability of layered perovskites can be leveraged to reduce phase transition hysteresis through careful control over the inorganic–organic interface. The combination of ultralow hysteresis and high pressure sensitivity leads to colossal reversible isothermal entropy changes (>200 J kg -1 K -1 ) at record-low pressures (<300 bar).

36 MATERIALS SCIENCE↗
DOE OSTI2024

Lithography-Free Mesa Isolation of III–V Solar Cells Through Laser Ablation

Eliminating photolithography from solar cell processing is a significant opportunity for cost reduction for III-V solar cells. Here, in this work, we explore femtosecond laser ablation as an alternative to contact photolithography and wet chemical etching for mesa isolation. We demonstrate both GaAs and GaInP solar cells mesa-isolated by femtosecond laser ablation with minimal to no loss in solar cell performance. We show the best results with a 400 fs UV pulsed laser and a short clean-up etch that also serves as a contact layer removal etch.

14 SOLAR ENERGY↗
DOE OSTI2022

Evaluating Contributions of Pitch-Carbon Coating to Improved Stability of Si Anodes Through Voltage-Resolved Multi-Phase Characterization

Silicon nanoparticles have emerged as a promising alternative to graphite to improve the energy density of next-generation lithium-ion battery anodes. Nano-sized Si domains facilitate rapid ion transport and minimize particle-scale mechanical degradation, but also exhibit increased (electro)chemical reactivity with Li-ion electrolyte components due to their high surface area. We have previously demonstrated that surface modification of Si nanoparticles with pitch-carbon is an effective strategy to reduce these parasitic reactions. In the present work, we holistically evaluate the mechanistic contribution of pitch-carbon coating to the observed stability improvement over uncoated Si. We utilize coupled in situ and ex situ methods to probe changes to solid-surface, volatile headspace, and gas-phase chemistry occurring during initial cycling. Measurements taken at targeted potentials associated with electrolyte species reduction enables the decoupling of specific reaction pathways tied to interfacial stability. Further, we demonstrate the non-trivial role of gas reconsumption in dictating the nature of the passivating surface layer evolved on both uncoated and pitch-coated Si. This multi-phase analysis offers insights into the mechanism of effective surface passivation, which may be applied to inform future Si material development.

ENERGY STORAGE↗
DOE OSTI2020

Continuous Monitoring and Partial Water Softening for Cooling Tower Water Treatment

Cooling towers are an integral component of many refrigeration systems, providing comfort or process cooling across a broad range of applications. They are the point in the system where heat is dissipated to the atmosphere through the evaporative cooling process. Cooling towers are commonly found in industrial applications and are also often used in water-cooled chilled water plants in medium to large commercial buildings. Continuous monitoring and partial water softening for cooling towers used in medium to large commercial buildings are the focus of this paper. Cooling towers consume large amounts of water. Cooling tower-related water consumption is one of largest potable water loads within buildings in the United States, with substantial building water use associated with heating and cooling. Regional water shortages have highlighted a need to reduce water consumption; the U.S. General Services Administration (GSA) and Executive Order 13834 place priority on reducing water consumption. This priority has fueled interest in the identification, investigation, and potential broad deployment of cost-effective opportunities to reduce water use, such as alternative water treatment (AWT) technologies for cooling towers. Traditional water treatment approaches use chemicals to extend the ability of the water to hold scaling minerals in suspension, minimize corrosion, and prevent biological growth. This treatment protects the chillers and cooling tower equipment; however, even when chemicals are used regularly, a certain percentage of condenser water must be drained and made up with fresh water to maintain system water quality parameters. In addition, the use of chemicals sometimes creates a waste disposal issue and can cause building owners to incur additional fees, such as disposal or wastewater charges. To manage cooling tower water treatment, GSA typically contracts with a company specializing in conventional chemical maintenance for a fixed fee. While there are many types and vendors of AWT systems, this project assesses the effectiveness of one technology provided by Aqualogix. This system is a chilled water plant monitoring and control system aimed at optimizing system performance by reducing the blowdown occurrences used to remove mineral build-up. The technology consists of two components – continuous programmable logic control (PLC) monitoring and side-stream filtration with partial water softening. PLC monitoring calculates cycles of concentration (CoC) and determines the optimum amount of blowdown water required to satisfy all water chemistry requirements. Side-stream filtration removes suspended matter and improves biocide efficacy while precisely dispensing softened water to achieve optimal makeup water hardness. Unlike other AWT systems evaluated by GSA to date, this system does not replace the legacy treatment system but is used in addition to chemical water treatment. The vendor claims their technology will reduce water consumption, water discharge, and maintenance costs. The AWT system evaluated in this demonstration is a commercialized technology. Given its commercialized state, the system evaluated in this report is at a Technology Readiness Level 9 according to National Aeronautics and Space Administration (NASA) definitions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

MaxTech HPWH Using Ultra-low GWP Refrigerant

Heat pump water heaters (HPWHs) are a proven technology for water heating that has been commercialized. The adoption of HPWHs for domestic and commercial water heating is growing rapidly because of superior performance compared with that of alternative water heating methods. Whereas most existing systems use R-134a as a working refrigerant, significant interest exists for deploying low global warming potential refrigerants to minimize environmental impacts.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
NASA NTRS1976

Identification of natural frequencies and modal damping ratios of aerospace structures from response data

An analysis of one and multidegree of freedom systems with classical damping is presented. Definition and minimization of error functions for each system are discussed. Systems with classical and nonclassical normal modes are studied, and results for first order perturbation are given. An alternative method of matching power spectral densities is provided, and numerical results are reviewed.

Michalopoulos, C. D.↗
NASA NTRS1980

AMTV headway sensor and safety design

A headway sensing system for an automated mixed traffic vehicle (AMTV) employing an array of optical proximity sensor elements is described, and its performance is presented in terms of object detection profiles. The problem of sensing in turns is explored experimentally and requirements for future turn sensors are discussed. A recommended headway sensor configuration, employing multiple source elements in the focal plane of one lens operating together with a similar detector unit, is described. Alternative concepts including laser radar, ultrasonic sensing, imaging techniques, and radar are compared to the present proximity sensor approach. Design concepts for an AMTV body which will minimize the probability of injury to pedestrians or passengers in the event of a collision are presented.

Johnston, A. R.↗
NASA NTRS2007

Design Concept for a Nuclear Reactor-Powered Mars Rover

A report presents a design concept for an instrumented robotic vehicle (rover) to be used on a future mission of exploration of the planet Mars. The design incorporates a nuclear fission power system to provide long range, long life, and high power capabilities unachievable through the use of alternative solar or radioisotope power systems. The concept described in the report draws on previous rover designs developed for the 2009 Mars Science laboratory (MSL) mission to minimize the need for new technology developments.

Elliott, John↗
NASA NTRS2015

Experimental Validation of the Dynamic Inertia Measurement Method to Find the Mass Properties of an Iron Bird Test Article

The mass properties of an aerospace vehicle are required by multiple disciplines in the analysis and prediction of flight behavior. Pendulum oscillation methods have been developed and employed for almost a century as a means to measure mass properties. However, these oscillation methods are costly, time consuming, and risky. The NASA Armstrong Flight Research Center has been investigating the Dynamic Inertia Measurement, or DIM method as a possible alternative to oscillation methods. The DIM method uses ground test techniques that are already applied to aerospace vehicles when conducting modal surveys. Ground vibration tests would require minimal additional instrumentation and time to apply the DIM method. The DIM method has been validated on smaller test articles, but has not yet been fully proven on large aerospace vehicles.

moments of inertia↗