Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WAVE INTERACTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Numerical study of shock-wave/boundary-layer interactions with bleed

A numerical study was conducted to investigate how bleed through a two-dimensional slot affects shock-wave induced, boundary-layer separation on a flat plate. This study is based on the ensemble-averaged, compressible, Navier-Stokes equations closed by the Baldwin-Lomax, algebraic turbulence model. The algorithm used to obtain solutions was the implicit, partially split, two-factored scheme of Steger. This study examined the effects of the following parameters in controlling shock-wave induced flow separation: location of slot in relation to where the incident shock wave impinged on the boundary layer, size of slot in relation to the boundary-layer thickness, number of slots, spacings between slots, and strength of the incident shock wave. This study also showed the nature of the very complex flowfield about the slot or slots and how the plenum affects the bleed process. The results of this study are relevant to problems where bleed is used to control shock-wave induced, boundary-layer separation (e.g., inside jet engine inlets and wind tunnels).

Hahn, T. O.↗
NASA NTRS2017

Instability Wave-Streak Interactions in a Supersonic Boundary Layer

Optimal initial conditions for transient growth in a two-dimensional boundary layer flow correspond to stationary, counter-rotating vortices that subsequently develop into streamwise elongated streaks, which are characterized by an alternating pattern of low and high streamwise velocity. For incompressible flows, previous studies have shown that boundary layer modulation due to streaks below a threshold amplitude level can stabilize the Tollmien-Schlichting instability waves, resulting in a delay in the onset of laminar-turbulent transition. In the supersonic regime, the linearly, most-amplified waves become three-dimensional, corresponding to oblique, first-mode waves. This change in the character of dominant instabilities leads to an important change in the transition process, which is now dominated by oblique breakdown via nonlinear interactions between pairs of first-mode waves that propagate at equal but opposite angles with respect to the free stream. Because the oblique breakdown process is characterized by a rapid amplification of stationary streamwise streaks, artificial excitation of such streaks may be expected to promote transition in a supersonic boundary layer. Indeed, suppression of those streaks has been shown to delay the onset of transition in prior literature. Consistent with those findings, the present study shows that optimally growing stationary streaks indeed destabilize the first-mode waves, but only when the spanwise wavelength of the instability waves is equal to or smaller than twice the streak spacing. Transition in a benign disturbance environment typically involves first-mode waves with significantly longer spanwise wavelengths, and hence, these waves are stabilized by the optimal growth streaks. Thus, as long as the amplification factors for the destabilized, short wavelength instability waves remain below the threshold level for transition, a significant net stabilization is achieved, yielding a transition delay that is comparable to the length of the laminar region in the uncontrolled case.

Boundary layer transition↗
DOE OSTI2021

An SYK-inspired model with density–density interactions: Spectral & wave function statistics, Green’s function and phase diagram

The Sachdev–Ye–Kitaev (SYK) model is a rare example of a strongly-interacting system that is analytically tractable. Tractability arises because the model is largely structureless by design and therefore artificial: while the interaction is restricted to two-body terms, interaction matrix elements are “randomized” and therefore the corresponding interaction operator does not commute with the local density. Unlike conventional density–density-type interactions, the SYK-interaction is, in this sense, not integrable. We here investigate a variant of the (complex) SYK model, which restores this integrability. It features a randomized single-body term and a density–density-type interaction. We present numerical investigations suggesting that the model exhibits two integrable phases separated by several intermediate phases including a chaotic one. The chaotic phase carries several characteristic SYK-signatures including in the spectral statistics and the frequency scaling of the Green’s function and therefore should be adiabatically connected to the non-Fermi liquid phase of the original SYK model. Thus, our model Hamiltonian provides a bridge from the SYK-model towards microscopic realism.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

Physics-constrained Gaussian process model for prediction of hydrodynamic interactions between wave energy converters in an array

To improve the efficiency of wave farms and achieve maximum power generation, the layout of wave energy converters (WECs) in an array needs to be carefully designed so that the hydrodynamic interactions can be positively exploited. For this, the hydrodynamic characteristics of the WEC array in different layouts need to be calculated. However, such calculations using numerical models usually entail significant computational cost, especially for large arrays of WECs. To address the computational challenge, a physics-constrained Gaussian process (GP) model is proposed to replace the original expensive numerical model and predict the hydrodynamic characteristics of the WECs for any array layout. By exploring the relationship between the WEC array (i.e., the input) and different hydrodynamic characteristics (i.e., the output), here we summarize a set of physical constraints/features, including invariance, symmetry, and additivity. This prior knowledge about the input-output relationship is then directly embedded in the constructed GP model through the design of physics-constrained kernels. In particular, a double-sum invariant kernel is first developed to incorporate the invariance and symmetry features, and then an additive kernel is developed to incorporate the additive feature of the problem. The invariant kernel and the additive kernel are then integrated to construct the physics-constrained GP model. Compared to the standard GP model, the proposed physics-constrained GP models require less training data to achieve the desired accuracy in predicting the hydrodynamic characteristics and are also less vulnerable to the curse of dimensionality (i.e., good scalability for large arrays) due to the use of an additive kernel. The efficiency, accuracy, and scalability of the proposed approach are demonstrated through an application to predict the hydrodynamic characteristics for WEC arrays of different sizes and layouts.

16 TIDAL AND WAVE POWER↗
NASA NTRS1975

On the calculation of supersonic separating and reattaching flows

A method is developed for solving the laminar and turbulent compressible boundary layer equations for separating and reattaching flows. Results of this method are compared with experimental data for two laminar and three turbulent layer, shock wave interactions. Several Navier-Stokes solutions are obtained for each of the laminar boundary layer, shock wave interactions considered. Comparison of these solutions indicates a first order sensitivity in C sub f to the computational mesh selected in both the viscous and inviscid portions of the flow. Comparison of the present boundary layer solutions with the Navier-Stokes solutions and with data for a given Mach number indicates that as long as the separation bubble is small, the boundary layer approximation yields solutions whose accuracy is comparable to the Navier-Stokes solutions.

Murphy, J. D.↗
NASA NTRS1984

Wave-particle interactions in the Venus wake and tail

The first descriptions of combined tail measurements from the Pioneer Venus plasma analyzer, magnetometer, and plasma wave detector are presented. The analysis concentrates on those orbits which are representative of the first tail passage. Summary plasma analyzer parameters are used to show that waves occurring at the boundary of the magnetotail can be identified as Doppler-shifted ion acoustic oscillations. High-density plasma distributions in the magnetotail region usually appear to be non-Maxwellian at the highest time resolution. These distorted distribution functions are generally accompanied by enhanced plasma wave signals and magnetic field reversals indicative of electric currents. A different time for the spacecraft entrance into the magnetotail from that previously defined is identified. It is shown that the wave activity in the Venus tail appears similar to the broadband noise identified in the earth's tail, except that at Venus the levels are usually higher.

Intriligator, D. S.↗
DOE OSTI2014

Simulations and Analysis of the Reshocked Inclined Interface Richtmyer–Meshkov Instability for Linear and Nonlinear Interface Perturbations

A computational study of the Richtmyer–Meshkov instability (RMI) is presented for an inclined interface perturbation in support of experiments being performed at the Texas A&M shock tube facility. The study is comprised of 2D, viscous, diffusive, compressible simulations performed using the arbitrary Lagrange Eulerian code, ARES, developed at Lawrence Livermore National Laboratory. These simulations were performed to late times after reshock with two initial interface perturbations, in the linear and nonlinear regimes each, prescribed by the interface inclination angle. The interaction of the interface with the reshock wave produced a complex 2D set of compressible wave interactions including expansion waves, which also interacted with the interface. Distinct differences in the interface growth rates prior to reshock were found in previous work. The current work provides in-depth analysis of the vorticity and enstrophy fields to elucidate the physics of reshock for the inclined interface RMI. After reshock, the two cases exhibit some similarities in integral measurements despite their disparate initial conditions but also show different vorticity decay trends, power law decay for the nonlinear and linear decay for the linear perturbation case.

42 ENGINEERING↗
DOE OSTI2024

Shock-induced twinning/detwinning and spall failure in Cu–Ta nanolaminates at atomic scales

Here, this study provides new insights into the role of interfaces on the deformation and failure mechanisms in shock-loaded Cu–Ta–Cu trilayer system. The thickness of the Ta layer, piston velocities, and shock pulse durations were varied to explore the impact of impedance mismatch and loading conditions on spallation behavior and twin formation. It was found that the interfaces play a crucial role in the dynamic response of these multilayered systems since secondary reflection waves generated at the interfaces significantly affected the peak stress and pressure profiles, influencing void nucleation and failure modes. In the trilayer systems, failure predominantly occurred at interfaces and within the Ta layer, with void nucleation sites and twinning behavior being markedly different compared to single-crystal Cu and Ta. Increasing the Ta layer thickness modified the wave interactions, leading to different failure locations. Higher piston velocities were associated with increased spall strength by enhancing wave interactions and void formation, particularly at the interfaces and within the Ta layer, under specific configurations. Additionally, shorter shock pulse durations facilitated earlier initiation of the release fan, reducing twin formation and altering the failure dynamics by accelerating twin annihilation and pressure release.

36 MATERIALS SCIENCE↗
NASA NTRS1975

On the calculation of supersonic, separating, and reattaching flows

A method is developed for solving the laminar and turbulent compressible boundary-layer equations for separating and reattaching flows. Results of this method are compared with experimental data for two laminar and three turbulent boundary-layer, shock-wave interactions. Several Navier-Stokes solutions were obtained for each of the laminar boundary-layer, shock-wave interactions considered. Comparison of these solutions indicates a first-order sensitivity in C sub f to the computational mesh selected in both the viscous and inviscid portions of the flow.

Murphy, J. D.↗
DOE OSTI2023

Quantum three-wave instability

For the three-wave interaction, the lowest-order nonlinear interaction in plasma dynamics, we describe how the quantum system, which is time-independent, nonchaotic, finite-dimensional, and Hermitian, can give rise to a linear instability corresponding to that in the classical system. Furthermore, we show that the instability is realized in the quantum regime as a cascade of the wave function in the space of occupation number states, and the unstable quantum system has a richer spectrum and a much longer recurrence time than the stable quantum system. The conditions for instability of the quantum three-wave interaction are described.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

On the effects of reactant stratification and wall curvature in non-premixed rotating detonation combustors

The optimization of non-premixed rotating detonation combustors (RDCs) requires improved understanding of the coupled effects of reactant stratification, fluid property gradients, and complex shock-wave interactions on the detonation wave structure within annular geometries. In the current work, simultaneous orthogonal views of chemiluminescence and hydroxyl planar laser-induced fluorescence (PLIF) are utilized to establish the existence of a dual-wave system characterized by leading and trailing detonation waves that are closely coupled by the local flow physics. These features are persistent over a wide range of mass flow rates and are consistent with prior observations of non-premixed rotating detonations in annular geometries. The detailed instantaneous time sequences are compared with a 3D reactive unsteady Reynolds averaged Navier-Stokes (URANS) simulation to more clearly elucidate the in-situ combustion dynamics and the sensitivity to reactant inlet conditions. It is found that the dual-wave system results from unburned reactants that survive the leading detonation wave in the injector near field and are consumed within a trailing azimuthal reflected-shock combustion (ARSC) zone. By contrast, the injector far field is characterized by rapid mixing due to a sudden drop to subsonic conditions, and the bifurcated detonation wave structure collapses into a stronger, single-wave detonation front with higher overall pressure ratio as compared with the dual-wave system. While each RDC will have different inflow, mixing, and combustion characteristics, the underlying interactions between the stratified reactants and azimuthal wave dynamics identified through the combination of advanced MHz-rate diagnostics and 3D numerical simulations have important implications for the study of detonation wave stability, mode transition, and combustion efficiency in non-premixed annular RDCs.

3D URANS↗
NASA NTRS1992

Measurements of the interaction of wave groups with shorter wind-generated waves

Fields of statistically steady wind-generated waves produced in a wind wave facility were perturbed by the injection of groups of longer, mechanically generated waves with various slopes. The time histories of the surface displacements were measured at four fetches in ensembles consisting of 100 realizations of each set of experimental conditions; the data were stored and analyzed digitally. Four distinct stages in the overall interaction are identified and characterized. The properties of the wave energy front are documented, and a preliminary discussion is given of the dynamic processes involved in its formation.

Chu, Jacob S.↗
NASA NTRS2012

Electron Micro Bursts as a Mechanism of Electron Loss Via Wave-Particle Interactions

Electron microbursts are rapid fluctuations of electron fluxes occurring on time scales of milliseconds. They are thought be due to scattering into the loss cone by plasma waves of various types from chorus to the recently observed large amplitude whistlers. They may be a major process of loss of realtivistic electrons from the Earth's outer radiation belts. One of the key issues that new mission s such as RBSP will address is to understand the loss of relativistic electrons. The SAMPEX mission launched in 1992 and still collecting data has the HILT sensor onboard with the capability of measuring> 1 MeV electrons with a high time resolution of 20 milliseconds suited admirably for the study of microbursts. We will use the data collected by the HILT for over a decade to characterize the relationship between electron microbursts and macroscopic electron decay lifetimes. With the launch of RBSP it is expected that SAMPEX will continue to collect data and overlap with RBSP. The latter will provide valuable information regarding plasma waves which coupled with low altitude measurements of microbursts may help elucidate details of the physics of electron loss from the radiation belt.

Kanekal, Shrikanth↗
DOE OSTI2022

Resonant wave–filament interactions as a loss mechanism for HHFW heating and current drive

Abstract Perkins et al (2012 Phys. Rev. Lett. 109 045001) reported unexpected power losses during high harmonic fast wave (HHFW) heating and current drive in the National Spherical Torus Experiment (NSTX). Recently, Tierens et al (2020 Phys. Plasmas 27 010702) proposed that these losses may be attributable to surface waves on field-aligned plasma filaments, which carry power along the filaments, to be lost at the endpoints where the filaments intersect the limiters. In this work, we show that there is indeed a resonant loss mechanism associated with the excitation of these surface waves, and derive an analytic expression for the power lost to surface wave modes at each filament.

Tierens, W. (ORCID:0000000269798140)↗
NASA NTRS1970

Lagrangian description of warm plasmas

Efforts are described to extend the averaged Lagrangian method of describing small signal wave propagation and nonlinear wave interaction, developed by earlier workers for cold plasmas, to the more general conditions of warm collisionless plasmas, and to demonstrate particularly the effectiveness of the method in analyzing wave-wave interactions. The theory is developed for both the microscopic description and the hydrodynamic approximation to plasma behavior. First, a microscopic Lagrangian is formulated rigorously, and expanded in terms of perturbations about equilibrium. Two methods are then described for deriving a hydrodynamic Lagrangian. In the first of these, the Lagrangian is obtained by velocity integration of the exact microscopic Lagrangian. In the second, the expanded hydrodynamic Lagrangian is obtained directly from the expanded microscopic Lagrangian. As applications of the microscopic Lagrangian, the small-signal dispersion relations and the coupled mode equations are derived for all possible waves in a warm infinite, weakly inhomogeneous magnetoplasma, and their interactions are examined.

Kim, H.↗
DOE OSTI2021

The geometry of the ICRF-induced wave–SOL interaction. A multi-machine experimental review in view of the ITER operation

As a part of ITPA-Integrated Operational Scenario activities, this contribution reviews recent experimental characterizations of radio-frequency (RF)-induced scrape-off layer (SOL) modifications of various tokamaks worldwide and of the LArge Plasma Device at UCLA. The phenomenology, as observed using a large variety of measurement techniques, is consistent with expectations from RF sheath rectification. Emphasis is then put on the complex three-dimensional (3D) spatial patterns of the RF–SOL interaction, in relation to the magnetic topology and the spatial distribution of RF currents over the metallic structures surrounding the RF wave launchers. Dependence on the local plasma parameters in the antenna vicinity is also briefly addressed. The final part discusses implications for future devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗