Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “W”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Preliminary evaluation of tensile and stress-rupture behavior of W + 24 at. pct Re + 0.4 at. pct HfC wire

Results are presented of an evaluation of tensile properties and stress-rupture bahavior of a small-diameter W24ReHfC (W-24Re-0.4(HfC)) wire, which is considered to be an excellent reinforcing fiber candidate for a variety of metal-matrix composites. The results were compared to data of Petrasek (1972) on W4ReHfC (W-4Re-0.4(HfC)) wire. It was found that the room-temperature (RT) tensile strength of the W24ReHfC wire was about 3250 MPa, higher than that of the W4ReHfC (3160 MPa) and WHfC (2250 MPa) wires. Above 1366 K, the W4ReHfC wire had both a greater tensile strength and the stress rupture strength than the W24ReHfC wire.

Yun, H. M.↗

Experimental characteristics and performance analysis of monolithic InP-based HEMT mixers at W-band

Experimental characteristics of monolithic InAlAs/InGaAs HEMT mixers are presented together with a theoretical analysis. Experiments at W-band show a maximum conversion gain of 0.9 dB with 2 dBm of LO power level. This is the first demonstration of a monolithic HEMT mixer with conversion gain at W-band. The conversion gain dependence on LO power, RF frequency and gate bias is measured and compared with the theoretical predictions. Good agreement between the theory and experiment could be found.

Kwon, Youngwoo↗

KONUS-W gamma-ray burst experiment for ISTP WIND spacecraft

The primary task of the KONUS-W experiment to be flown on board the WIND spacecraft is to observe gamma-ray bursts and solar flares with moderate and high time resolution. The scientific objectives of the experiment include the study of continuum energy spectra and spectral features of these events in the energy range of 10 keV to 10 MeV as well as their time histories in soft, medium, and hard energy bands with a time resolution up to 2 ms. The general design and operation of the KONUS-W gamma-ray detector are briefly described, and the nomial program of burst observations is examined.

Aptekar', R. L.↗

Photometric investigation of a very short period W UMa-type binary - Does CE Leonis have a large superluminous area?

A complete photometric analysis of BVRI Johnson-Cousins photometry of the high northern latitude galactic variable, CE Leo is presented. These observations were taken at Kitt Peak National Observatory on May 31, 1989-June 7, 1989. Three new precise epochs of minimum light were determined and a linear and a quadratic ephemeris were computed from these and previous data covering 28 years of observation. The light curves reveal that the system undergoes a brief 20 min totality in the primary eclipse, indicating that CE Leo is a W UMa W-type binary. A systemic velocity of about -40 km/s was determined. Standard magnitudes were found and a simultaneous solution of the B, V, R, I light curves was computed using the new Wilson-Devinney synthetic light curve code which has the capability of automatically adjusting star spots. The solution indicates that the system consists of two early K-type dwarfs in marginal contact with a fill-out factor less than 3 percent. Evidence for the presence of a large (45 deg radius) superluminous area on the cooler component is given.

Samec, Ronald G.↗

Tensile strength of simulated and welded butt joints in W-Cu composite sheet

The weldability of W-Cu composite sheet was investigated using simulated and welded joints. The welded joints were produced in a vacuum hot press. Tensile test results showed that simulated joints can provide strength and failure mode data which can be used in joint design for actual weldments. Although all of the welded joints had flaws, a number of these joints were as strong as the W-Cu composite base material.

Moore, Thomas J.↗

Coseismic fault slip associated with the 1992 M(sub w) 6.1 Joshua Tree, California, earthquake: Implications for the Joshua Tree-Landers earthquake sequence

Coseismic surface deformation associated with the M(sub w) 6.1, April 23, 1992, Joshua Tree earthquake is well represented by estimates of geodetic monument displacements at 20 locations independently derived from Global Positioning System and trilateration measurements. The rms signal to noise ratio for these inferred displacements is 1.8 with near-fault displacement estimates exceeding 40 mm. In order to determine the long-wavelength distribution of slip over the plane of rupture, a Tikhonov regularization operator is applied to these estimates which minimizes stress variability subject to purely right-lateral slip and zero surface slip constraints. The resulting slip distribution yields a geodetic moment estimate of 1.7 x 10(exp 18) N m with corresponding maximum slip around 0.8 m and compares well with independent and complementary information including seismic moment and source time function estimates and main shock and aftershock locations. From empirical Green's functions analyses, a rupture duration of 5 s is obtained which implies a rupture radius of 6-8 km. Most of the inferred slip lies to the north of the hypocenter, consistent with northward rupture propagation. Stress drop estimates are in the range of 2-4 MPa. In addition, predicted Coulomb stress increases correlate remarkably well with the distribution of aftershock hypocenters; most of the aftershocks occur in areas for which the mainshock rupture produced stress increases larger than about 0.1 MPa. In contrast, predicted stress changes are near zero at the hypocenter of the M(sub w) 7.3, June 28, 1992, Landers earthquake which nucleated about 20 km beyond the northernmost edge of the Joshua Tree rupture. Based on aftershock migrations and the predicted static stress field, we speculate that redistribution of Joshua Tree-induced stress perturbations played a role in the spatio-temporal development of the earth sequence culminating in the Landers event.

Bennett, Richard A.↗

Influence of Cr and W alloying on the fiber-matrix interfacial shear strength in cast and directionally solidified sapphire NiAl composites

Sapphire-reinforced NiAl matrix composites with chromium or tungsten as alloying additions were synthesized using casting and zone directional solidification (DS) techniques and characterized by a fiber pushout test as well as by microhardness measurements. The sapphire-NiAl(Cr) specimens exhibited an interlayer of Cr rich eutectic at the fiber-matrix interface and a higher interfacial shear strength compared to unalloyed sapphire-NiAl specimens processed under identical conditions. In contrast, the sapphire-NiAl(W) specimens did not show interfacial excess of tungsten rich phases, although the interfacial shear strength was high and comparable to that of sapphire-NiAl(Cr). The postdebond sliding stress was higher in sapphire-NiAl(Cr) than in sapphire-NiAl(W) due to interface enrichment with chromium particles. The matrix microhardness progressively decreased with increasing distance from the interface in both DS NiAl and NiAl(Cr) specimens. The study highlights the potential of casting and DS techniques to improve the toughness and strength of NiAl by designing dual-phase microstructures in NiAl alloys reinforced with sapphire fibers.

Asthana, R.↗

W-Band Free Space Permittivity Measurement Setup for Candidate Radome Materials

This paper presents a measurement system used for w-band complex permittivity measurements performed in NASA Langley Research Center's Electromagnetics Research Branch. The system was used to characterize candidate radome materials for the passive millimeter wave (PMMW) camera experiment. The PMMW camera is a new technology sensor, with goals of all-weather landings of civilian and military aircraft. The sensor is being developed under a NASA Technology Reinvestment program with TRW, McDonnell- Douglas, Honeywell, and Composite Optics, Inc. as participants. The experiment is scheduled to be flight tested on the Air Force's 'Speckled Trout' aircraft in late 1997. The camera operates at W-band, in a radiometric capacity and generates an image of the viewable field. Because the camera is a radiometer, the system is very sensitive to losses. Minimal transmission loss through the radome at the operating frequency, 89 GHz, was critical to the success of the experiment. This paper details the design, set-up, calibration and operation of a free space measurement system developed and used to characterize the candidate radome materials for this program.

Fralick, Dion T.↗

GPS Monitoring of Surface Change During and Following the Fortuitous Occurrence of the M(sub w) = 7.3 Landers Earthquake in our Network

Accomplishments: (1) Continues GPS monitoring of surface change during and following the fortuitous occurrence of the M(sub w) = 7.3 Landers earthquake in our network, in order to characterize earthquake dynamics and accelerated activity of related faults as far as 100's of kilometers along strike. (2) Integrates the geodetic constraints into consistent kinematic descriptions of the deformation field that can in turn be used to characterize the processes that drive geodynamics, including seismic cycle dynamics. In 1991, we installed and occupied a high precision GPS geodetic network to measure transform-related deformation that is partitioned from the Pacific - North America plate boundary northeastward through the Mojave Desert, via the Eastern California shear zone to the Walker Lane. The onset of the M(sub w) = 7.3 June 28, 1992, Landers, California, earthquake sequence within this network poses unique opportunities for continued monitoring of regional surface deformation related to the culmination of a major seismic cycle, characterization of the dynamic behavior of continental lithosphere during the seismic sequence, and post-seismic transient deformation. During the last year, we have reprocessed all three previous epochs for which JPL fiducial free point positioning products available and are queued for the remaining needed products, completed two field campaigns monitoring approx. 20 sites (October 1995 and September 1996), begun modeling by development of a finite element mesh based on network station locations, and developed manuscripts dealing with both the Landers-related transient deformation at the latitude of Lone Pine and the velocity field of the whole experiment. We are currently deploying a 1997 observation campaign (June 1997). We use GPS geodetic studies to characterize deformation in the Mojave Desert region and related structural domains to the north, and geophysical modeling of lithospheric behavior. The modeling is constrained by our existing and continued GPS measurements, which will provide much needed data on far-field strain accumulation across the region and on the deformational response of continental lithosphere during and following a large earthquake, forming the basis for kinematic and dynamic modeling of secular and seismic-cycle deformation. GPS geodesy affords both regional coverage and high precision that uniquely bear on these problems.

Miller, M. Meghan↗

A Monolithic W-Band Three-Stage LNA Using 0.1 Micron InAlAs/InGaAs/InP HEMT Technology

A monolithic W-band three-stage Low Noise Amplifiers (LNA) based on 0.1 um pseudomorphic InAlAs/InGaAs/InP (High Electron Mobility Transistors (HEMTs) has been developed. this LNA demonstrated a noise figure of 4.3 dB and an associated small signal gain of 19 dB at 100 GHz with a low dc power consumption of 20 mW. This is the best reported monolithic W-band LNA performance using InP-based HEMT technology and demonstrates the potential of InP HEMT technology for higher millimeter-wave applications.

Wang, H.↗

Comparison of Ultrasound with Tensile Testing of Thermally Damaged Polyimide Insulated Wiring (MIL-W-81381)

Ultrasonic measurements were performed on MIL-W-81381/7, /12, and /21 wire, a polyimide (Kapton) insulated wire. The phase velocity for the 20-gauge MIL-W-81381/7 wire had a baseline value of 3023 plus or minus 78 m/s. After exposure to high temperatures, the wire's phase velocity rapidly increased, and reached an asymptotic value of 3598 plus or minus 20 m/s after 100 hours exposure. Similar responses were measured in other gauges. The baseline measurements of Young's moduli resulted in values of 5636 plus or minus 486, 7714 plus or minus 505, and 8767 plus or minus 292 KSI for the 20 ga, 16 ga, and 12 ga. wires respectively.

Madaras, Eric I.↗

Influence of Silicate Melt Composition on Metal/Silicate Partitioning of W, Ge, Ga and Ni

The depletion of the siderophile elements in the Earth's upper mantle relative to the chondritic meteorites is a geochemical imprint of core segregation. Therefore, metal/silicate partition coefficients (Dm/s) for siderophile elements are essential to investigations of core formation when used in conjunction with the pattern of elemental abundances in the Earth's mantle. The partitioning of siderophile elements is controlled by temperature, pressure, oxygen fugacity, and by the compositions of the metal and silicate phases. Several recent studies have shown the importance of silicate melt composition on the partitioning of siderophile elements between silicate and metallic liquids. It has been demonstrated that many elements display increased solubility in less polymerized (mafic) melts. However, the importance of silicate melt composition was believed to be minor compared to the influence of oxygen fugacity until studies showed that melt composition is an important factor at high pressures and temperatures. It was found that melt composition is also important for partitioning of high valency siderophile elements. Atmospheric experiments were conducted, varying only silicate melt composition, to assess the importance of silicate melt composition for the partitioning of W, Co and Ga and found that the valence of the dissolving species plays an important role in determining the effect of composition on solubility. In this study, we extend the data set to higher pressures and investigate the role of silicate melt composition on the partitioning of the siderophile elements W, Ge, Ga and Ni between metallic and silicate liquid.

Singletary, S. J.↗

Power-Combined GaN Amplifier with 2.28-W Output Power at 87 GHz

Future remote sensing instruments will require focal plane spectrometer arrays with higher resolution at high frequencies. One of the major components of spectrometers are the local oscillator (LO) signal sources that are used to drive mixers to down-convert received radio-frequency (RF) signals to intermediate frequencies (IFs) for analysis. By advancing LO technology through increasing output power and efficiency, and reducing component size, these advances will improve performance and simplify architecture of spectrometer array systems. W-band power amplifiers (PAs) are an essential element of current frequency-multiplied submillimeter-wave LO signal sources. This work utilizes GaN monolithic millimeter-wave integrated circuit (MMIC) PAs developed from a new HRL Laboratories LLC 0.15- m gate length GaN semiconductor transistor. By additionally waveguide power combining PA MMIC modules, the researchers here target the highest output power performance and efficiency in the smallest volume achievable for W-band.

Fung, King Man↗

A Compact Two-Stage 120 W GaN High Power Amplifier for SweepSAR Radar Systems

This work presents the design and measured results of a fully integrated switched power two-stage GaN HEMT high-power amplifier (HPA) achieving 60% power-added efficiency at over 120Woutput power. This high-efficiency GaN HEMT HPA is an enabling technology for L-band SweepSAR interferometric instruments that enable frequent repeat intervals and high-resolution imagery. The L-band HPA was designed using space-qualified state-of-the-art GaN HEMT technology. The amplifier exhibits over 34 dB of power gain at 51 dBm of output power across an 80 MHz bandwidth. The HPA is divided into two stages, an 8 W driver stage and 120 W output stage. The amplifier is designed for pulsed operation, with a high-speed DC drain switch operating at the pulsed-repetition interval and settles within 200 ns. In addition to the electrical design, a thermally optimized package was designed, that allows for direct thermal radiation to maintain low-junction temperatures for the GaN parts maximizing long-term reliability. Lastly, real radar waveforms are characterized and analysis of amplitude and phase stability over temperature demonstrate ultra-stable operation over temperature using integrated bias compensation circuitry allowing less than 0.2 dB amplitude variation and 2 deg phase variation over a 70 C range.

Thrivikraman, Tushar↗

Refractive Index of Polyaryletherketone (PEEK) at X- and W-Band

This report details refractive index measurements of polyaryletherketone (PEEK) thermoplastic between X-band (8 to 12 GHz) and W-band (75 to 110 GHz) frequencies. Scattering-parameter data are collected using both traditional waveguide and modified free-space techniques. The complex-valued refractive index is calculated using the standard Nicolson-Ross-Weir method. Results indicate that PEEK’s refractive index is n = 1.783 – 0.001i across X-band and n = 1.792 – 0.007i across W-band. Therefore, PEEK exhibits a moderate real refractive index component and low transmission loss. Coupled with its favorable mechanical and thermal properties, this makes PEEK an ideal material to inspect using NASA’s submillimeter radiofrequency-based technology.

Polyaryletherketone↗

Additive Manufacturing of Frequency-Agile W-Band Packaging

Abstract —In this paper we demonstrate a fully additively manufactured packaged W-band amplifier with integrated bypass capacitors. This package was fabricated using a chip-first approach and aerosol jet printing. Package substrates (dielectrics), conductors and interconnects are printed around a bare die attached to a carrier. This package uses shaped ramp interconnects, allowing for frequency agnostic package performance of the interconnect with no impedance discontinuity, within the physical limits of the printer. High dielectric constant thin films of a polymer-matrix nanocomposite for bypass capacitors were printed using multi-material aerosol jet printing. The maximum measured packaged gain is 14.9 dB in the W-band, compared to the maximum bare die gain of 15.5 dB in the same frequency range. From 75 - 92 GHz, the average package loss is 1.1 dB including 3 mm transmission line, interconnects, and a GSG launch structure correlating to an average loss of 0.37 dB/mm.

Additive manufacturing, aerosol jet printing, hete↗

Computational and Experimental Investigation of Discrete “W” Turbulators for sCO2 Turbine Internal Cooling

Direct-fired supercritical CO2 (sCO2 ) cycles are of particular interest for power generation due to the potential for higher thermal efficiencies with inherent CO2 capture. Direct fired sCO2 turbines must withstand high temperatures and the density of the working fluid is much higher than conventional Brayton cycles. Based on conventional Brayton cycle applications, internal serpentine cooling channels with ribbed turbulator strips are a common approach to achieve the required cooling, while minimizing coolant utilization. Most of the previous studies of coolant channel heat transfer enhancements have focused on serpentine channels using air as the cooling media at Reynold’s numbers typical of Brayton cycles. This paper investigates the Nusselt number augmentation of coolant channels with no features, ribbed turbulators, and discrete “W” turbulators with surface roughness effects included and CO2 as the coolant. The numerical results are compared to experimental results using CO2 as the cooling media at Reynold’s numbers ranging from 100,000 to 300,000. The results show the Nusselt number augmentation plateaus with increasing Reynolds number, in contrast to the decay observed in prior publications with air as the coolant media. Additionally, the CFD results indicate the discrete “W” geometry provides a 10% increase in Nusselt number augmentation relative to the angled ribbed turbulators.

computational fluid dynamics (CFD)↗

Search for new particles in events with a hadronically decaying W or Z boson and large missing transverse momentum at $\sqrt{s}$ = 13 TeV using the ATLAS detector

A search is presented for new particles produced in proton-proton collisions at a centre-of-mass energy of 13 TeV that result in final states comprising a massive vector ( W or Z ) boson that decays hadronically and large missing transverse momentum. The data sample was collected with the ATLAS experiment at the Large Hadron Collider from 2015 to 2018 and corresponds to an integrated luminosity of 140 fb - 1 . No significant excess over the Standard Model expectation is observed. Model-independent 95% confidence-level limits on the visible cross-section that range from 0.3 fb to 79.5 fb are obtained for non-Standard-Model processes. Exclusion limits are also presented for models with axion-like particles, for two-Higgs-doublet models with a pseudo-scalar mediator between the Standard Model and the dark sector, for the invisible decay of the Higgs boson and for pair-produced weakly interacting dark matter candidates.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗