Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Technology and Operations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1998

X-34 Vehicle Aerodynamic Characteristics

The X-34, being designed and built by the Orbital Sciences Corporation, is an unmanned sub-orbital vehicle designed to be used as a flying test bed to demonstrate key vehicle and operational technologies applicable to future reusable launch vehicles. The X-34 will be air-launched from an L-1011 carrier aircraft at approximately Mach 0.7 and 38,000 feet altitude, where an onboard engine will accelerate the vehicle to speeds above Mach 7 and altitudes to 250,000 feet. An unpowered entry will follow, including an autonomous landing. The X-34 will demonstrate the ability to fly through inclement weather, land horizontally at a designated site, and have a rapid turn-around capability. A series of wind tunnel tests on scaled models was conducted in four facilities at the NASA Langley Research Center to determine the aerodynamic characteristics of the X-34. Analysis of these test results revealed that longitudinal trim could be achieved throughout the design trajectory. The maximum elevon deflection required to trim was only half of that available, leaving a margin for gust alleviation and aerodynamic coefficient uncertainty. Directional control can be achieved aerodynamically except at combined high Mach numbers and high angles of attack, where reaction control jets must be used. The X-34 landing speed, between 184 and 206 knots, is within the capabilities of the gear and tires, and the vehicle has sufficient rudder authority to control the required 30-knot crosswind.

Brauckmann, Gregory J.↗
NASA NTRS2001

Status of the Direct Data Distribution (D(exp 3)) Experiment

NASA Glenn Research Center's Direct Data Distribution (D3) project will demonstrate an advanced, high-performance communications system that transmits information from an advanced technology payload carried by a NASA spacecraft in low Earth orbit (LEO) to a small receiving terminal on Earth. The space-based communications package will utilize a solid-state, K-band phased-array antenna that electronically steers the radiated energy beam toward a low-cost, tracking ground terminal, thereby providing agile, vibration-free, electronic steering at reduced size and weight with increased reliability. The array-based link will also demonstrate new digital processing technology that will allow the transmission of substantially increased amounts of latency-tolerant data collected from the LEO spacecraft directly to NASA field centers, principal investigators, or into the commercial terrestrial communications network. The technologies demonstrated by D3 will facilitate NASA's transition from using Government-owned communication assets to using commercial communication services. The hardware for D3 will incorporate advanced technology components developed under the High Rate Data Delivery (HRDD) Thrust Area of NASA's Office of Aerospace Technology Space Base Program at Glenn's Communications Technology Division. The flight segment components will include the electrically steerable phased-array antenna, which is being built by the Raytheon System Corporation and utilizes monolithic microwave integrated circuit (MMIC) technology operating at 19.05 GHz; and the digital encoder/modulator chipset, which uses four-channel orthogonal frequency division multiplexing (OFDM). The encoder/modulator will use a chipset developed by SICOM, Inc., which is both bandwidth and power efficient. The ground segment components will include a low-cost, open-loop tracking ground terminal incorporating a cryoreceiver to minimize terminal size without compromising receiver capability. The project is planning to hold a critical design review in the second quarter of fiscal year 2002.

Wald, Lawrence↗
NASA NTRS2009

From LEO, to the Moon and then Mars: Developing a Global Strategy for Exploration Risk Reduction

Most nations currently involved in human spaceflight, or with such ambitions, believe that space exploration will capture the imagination of our youth resulting in future engineers and scientists, advance technologies which will improve life on earth, increase the knowledge of our solar system, and strengthen bonds and relationships across the globe. The Global Exploration Strategy, published in 2007 by 14 space agencies, eloquently makes this case and presents a vision for space exploration. It argues that in order for space exploration to be sustainable, nations must work together to address the challenges and share the burden of costs. This paper will examine Mars mission scenarios developed by NASA, ESA and other agencies and show resulting conclusions regarding key challenges, needed technologies and associated mission risks. It will discuss the importance of using the International Space Station as a platform for exploration risk reduction and how the global exploration community will develop lunar exploration elements and architectures that enable the long term goal of human missions to Mars. The International Space Station (ISS) is a critical first step both from a technology and capability demonstration point of view, but also from a partnership point of view. There is much work that can be done in low earth orbit for exploration risk reduction. As the current "outpost at the edge of the frontier", the ISS is a place where we can demonstrate certain technologies and capabilities that will substantially reduce the risk of deploying an outpost on the lunar surface and Mars mission scenarios. The ISS partnership is strong and has fulfilled mission needs. Likewise, the partnerships we build on the moon will provide a strong foundation for establishing partnerships for the human Mars missions. On the moon, we build a permanently manned outpost and deploy technologies and capabilities to allow humans to stay for long periods of time. The moon is interesting from a scientific point of view, but it is extremely important for development and demonstration the technologies and capabilities needed for human missions to Mars. This paper will show the logic and strategy for addressing technological, operational and programmatic challenges by using low earth orbit and lunar missions to enable the long term goal of exploration of our solar system.

Laurini, Kathleen C.↗
NASA NTRS2012

Solar Electric Propulsion Vehicle Demonstration to Support Future Space Exploration Missions

Human and robotic exploration beyond Low Earth Orbit (LEO) will require enabling capabilities that are efficient, affordable, and reliable. Solar Electric Propulsion (SEP) is highly advantageous because of its favorable in-space mass transfer efficiency compared to traditional chemical propulsion systems. The NASA studies have demonstrated that this advantage becomes highly significant as missions progress beyond Earth orbit. Recent studies of human exploration missions and architectures evaluated the capabilities needed to perform a variety of human exploration missions including missions to Near Earth Objects (NEOs). The studies demonstrated that SEP stages have potential to be the most cost effective solution to perform beyond LEO transfers of high mass cargoes for human missions. Recognizing that these missions require power levels more than 10X greater than current electric propulsion systems, NASA embarked upon a progressive pathway to identify critical technologies needed and a plan for an incremental demonstration mission. The NASA studies identified a 30kW class demonstration mission that can serve as a meaningful demonstration of the technologies, operational challenges, and provide the appropriate scaling and modularity required. This paper describes the planning options for a representative demonstration 30kW class SEP mission.

Smith, Bryan K.↗
NASA NTRS2013

National Report on the NASA Sounding Rocket and Balloon Programs

The U. S. National Aeronautics and Space Administration (NASA) Sounding Rockets and Balloon Programs conduct a total of 30 to 40 missions per year in support of the NASA scientific community and other users. The NASA Sounding Rockets Program supports the science community by integrating their experiments into the sounding rocket payloads, and providing both the rocket vehicle and launch operations services. Activities since 2011 have included two flights from Andoya Rocket Range, more than eight flights from White Sands Missile Range, approximately sixteen flights from Wallops Flight Facility, two flights from Poker Flat Research Range, and four flights from Kwajalein Atoll. Other activities included the final developmental flight of the Terrier-Improved Malemute launch vehicle, a test flight of the Talos-Terrier-Oriole launch vehicle, and a host of smaller activities to improve program support capabilities. Several operational missions have utilized the new Terrier-Malemute vehicle. The NASA Sounding Rockets Program is currently engaged in the development of a new sustainer motor known as the Peregrine. The Peregrine development effort will involve one static firing and three flight tests with a target completion data of August 2014. The NASA Balloon Program supported numerous scientific and developmental missions since its last report. The program conducted flights from the U.S., Sweden, Australia, and Antarctica utilizing standard and experimental vehicles. Of particular note are the successful test flights of the Wallops Arc Second Pointer (WASP), the successful demonstration of a medium-size Super Pressure Balloon (SPB), and most recently, three simultaneous missions aloft over Antarctica. NASA continues its successful incremental design qualification program and will support a science mission aboard WASP in late 2013 and a science mission aboard the SPB in early 2015. NASA has also embarked on an intra-agency collaboration to launch a rocket from a balloon to conduct supersonic decelerator tests. An overview of NASA's Sounding Rockets and Balloon Operations, Technology Development and Science support activities will be presented.

Eberspeaker, Philip↗
NASA NTRS2013

A Motor Drive Electronics Assembly for Mars Curiosity Rover: An Example of Assembly Qualification for Extreme Environments

This paper describes the technology development and infusion of a motor drive electronics assembly for Mars Curiosity Rover under space extreme environments. The technology evaluation and qualification as well as space qualification of the assembly are detailed and summarized. Because of the uncertainty of the technologies operating under the extreme space environments and that a high level reliability was required for this assembly application, both component and assembly board level qualifications were performed.

Kolawa, Elizabeth↗
NASA NTRS2015

Handheld Fluorescence Resonance Energy Transfer (FRET)-Aptamer Sensor for Bone Markers

Astronauts lose significant bone mass during lengthy space flights. NASA wishes to monitor this bone loss in order to develop nutritional and exercise countermeasures. Operational Technologies Corporation (OpTech) has developed a handheld device that quantifies bone loss in a spacecraft environment. The innovation works by adding fluorescent dyes and quenchers to aptamers to enable pushbutton, one-step bind-and-detect FRET assays that can be freeze-dried, rehydrated with body fluids, and used to quantify bone loss.

Bruno, John G.↗
NASA NTRS2016

High-Lift Propeller System Configuration Selection for NASA's SCEPTOR Distributed Electric Propulsion Flight Demonstrator

Although the primary function of propellers is typically to produce thrust, aircraft equipped with distributed electric propulsion (DEP) may utilize propellers whose main purpose is to act as a form of high-lift device. These \high-lift propellers" can be placed upstream of wing such that, when the higher-velocity ow in the propellers' slipstreams interacts with the wing, the lift is increased. This technique is a main design feature of a new NASA advanced design project called Scalable Convergent Electric Propulsion Technology Operations Research (SCEPTOR). The goal of the SCEPTOR project is design, build, and y a DEP aircraft to demonstrate that such an aircraft can be much more ecient than conventional designs. This paper provides details into the high-lift propeller system con guration selection for the SCEPTOR ight demonstrator. The methods used in the high-lift propeller system conceptual design and the tradeo s considered in selecting the number of propellers are discussed.

Patterson, Michael D.↗
NASA NTRS2017

High-Lift Propeller Noise Prediction for a Distributed Electric Propulsion Flight Demonstrator

Over the past several years, the use of electric propulsion technologies within aircraft design has received increased attention. The characteristics of electric propulsion systems open up new areas of the aircraft design space, such as the use of distributed electric propulsion (DEP). In this approach, electric motors are placed in many different locations to achieve increased efficiency through integration of the propulsion system with the airframe. Under a project called Scalable Convergent Electric Propulsion Technology Operations Research (SCEPTOR), NASA is designing a flight demonstrator aircraft that employs many "high-lift propellers" distributed upstream of the wing leading edge and two cruise propellers (one at each wingtip). As the high-lift propellers are operational at low flight speeds (take-off/approach flight conditions), the impact of the DEP configuration on the aircraft noise signature is also an important design consideration. This paper describes efforts toward the development of a mulit-fidelity aerodynamic and acoustic methodology for DEP high-lift propeller aeroacoustic modeling. Specifically, the PAS, OVERFLOW 2, and FUN3D codes are used to predict the aerodynamic performance of a baseline high-lift propeller blade set. Blade surface pressure results from the aerodynamic predictions are then used with PSU-WOPWOP and the F1A module of the NASA second generation Aircraft NOise Prediction Program to predict the isolated high-lift propeller noise source. Comparisons of predictions indicate that general trends related to angle of attack effects at the blade passage frequency are captured well with the various codes. Results for higher harmonics of the blade passage frequency appear consistent for the CFD based methods. Conversely, evidence of the need for a study of the effects of increased azimuthal grid resolution on the PAS based results is indicated and will be pursued in future work. Overall, the results indicate that the computational approach is acceptable for fundamental assessment of low-noise high-lift propeller designs. The extent to which the various approaches may be used in a complementary manner will be further established as measured data becomes available for validation. Ultimately, it is anticipated that this combined approach may be used to provide realistic incident source fields for acoustic shielding/scattering studies on various aircraft configurations.

Nark, Douglas M.↗
NASA NTRS2019

Surface Biology & Geology Pathfinder Data Analysis Pipeline

NASA's future global orbital mission, currently in development as the Surface Biology and Geology (SBG) Designated Observable study, will acquire relatively high resolution solar-reflected spectroscopy and thermal infrared observations. Innovative processes must be utilized for handling the high volume of data anticipated to be collected, which is anticipated to exceed 100 terabytes/day, greater than NASA's total extant airborne hyperspectral data collection. Collecting, processing/re-processing, disseminating, and exploiting this volume of data presents new challenges. To begin addressing them, NASA is drawing upon the expertise developed from its astrophysics programs to address Earth science and applications. Specifically, NASA is adapting the science processing operations technology developed for the Kepler and TESS planet-hunting missions for imaging spectroscopy data processing. This technology development has been the foundation for the remarkable scientific successes of Kepler and TESS. The Kepler/TESS data processing technology provides a scalable architecture for robust, repeatable, and replicable science and application products while enabling the Earth science community to develop, test, and implement new algorithms. Our effort to leverage this existing capability has begun by ingesting data and applying workflows from the EO-1/Hyperion 17-year mission archive that provides globally sampled visible through shortwave infrared spectra that are representative of SBG data types and volumes. This pathfinding data processing system will help define the solutions to processing SBG data volumes and will enable the scientific community to interact with the data and processing pipeline to create new science products.

Jenkins, Jon↗
NASA NTRSDate not supplied

TPSAS-NF1676L-35311-DND

Objectives: - Inspect and identify the normal and abnormal cells, tissues, and biofluids (e.g., urine, serum, etc.) using a 532 nm pulsed laser within target distances of several centimeters (6 to 20 cm) and a line shaped laser spot-size 10 µm width by 5 mm height that would be suitable for astronauts’ health monitoring in space. Goals: - The goals of this research study are: - Solve some of the limitations of traditional micro-Raman systems (e.g., requires dark condition, sample collection, and slow) - build an instrument with pulsed-time gated Raman technology, operates in daylight, doesn’t require sample collection, and faster detection - Reduce the size and weight of the instrument - eliminate a high power laser and a large collection optics/telescope with a short working distance of several centimeters.

Nurul Abedin↗
NASA NTRSDate not supplied

NASA Small Spacecraft Technology Program

NASA's Small Spacecraft Technology Program will discuss the objectives, accomplishments, and current status of the Cislunar Autonomous Positioning System Technology Operations and Navigation Experiment (CAPSTONE) mission using the backdrop of CAPSTONE's instance in NASA's Eyes. Tools developed for use by mission planners and small spacecraft designers will be presented by NASA's Small Spacecraft System Virtual Institute.

Elwood F Agasid↗
NASA NTRSDate not supplied

Psychophysiological Methods to Assess Pilot Productive Safety Behaviors

The NASA System-Wide Safety (SWS) Project is focused on developing new technologies and operational concepts for the aviation industry to meet the increasing global demand while maintaining the current ultra-safe system safety levels. To achieve this, the SWS Project is developing research priorities, including In-time System-wide Safety Assurance (ISSA) and In-time Aviation Safety Management System (IASMS; Ellis et al., 2019). A critical component of the IASMS is the human as pilot and in other roles in aviation operations as demonstrated by SWS human factors research on rare occurrences of human error and the far more prevalent human safety producing behaviors (e.g., Hollnagel, 2016). The talk presented by Chad Stephens of NASA Langley Research Center and NASA SWS Project will describe the history of human factors research involving psychophysiological and biocybernetics methods supporting aviation safety conducted at NASA. Specific examples of recent NASA crew state monitoring research focused on a psychophysiological assessment method and system to enable Training for Attention Management will be demonstrated. Current SWS research including the SWS Operations and Technologies for Enabling Resilient In-Time Assurance (SOTERIA) flight simulation study and a data testbed created to enable study of Human Contributions to Safety (HC2S) will be presented. Ongoing collaborative research efforts with Boeing researchers will be highlighted and opportunities for further collaboration will be discussed.

psychophysiology↗
DOE OSTI2022

ESTABLISHING ETHICAL GUIDELINES FOR APPLYING ARTIFICIAL INTELLIGENCE TO IAEA SAFEGUARDS

Drawing upon globally recognized efforts by a variety of institutions, the paper develops a practical and defensible framework for consideration and use by the International Atomic Energy Agency (IAEA) to support the adoption of credible ethical standards for autonomous and intelligent systems (AIS). The analysis is based on a future hypothetical AIS that identifies signatures of misuse, diversion, and other research and development (R&D). The hypothetical system serves as an exemplar for subject matter expert (SME) workshop participants to begin to answer ethical AIS questions around how these systems should be governed and maintained, what the internal and external considerations associated with artificial intelligence (AI) tools are, and where the boundaries between ethical and non-ethical uses are. The ethical AIS workshop explored several important topics: (a) Recommendations that can be currently implemented by the IAEA, (b) Proposed defensible criteria and metrics aligned with an ethical AI for safeguards implementation, (c) Discussion of future needs and capabilities, and (d) Derive appropriate next steps and actions to support filling current technological, operational, and cultural gaps and realizing an effective ethical AI for safeguards framework. The Establishing Ethical Guidelines for Applying AI to IAEA Safeguards project creates awareness in the community of the ethical AIS approach.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗
DOE OSTI2022

Always look on the bright side of life: Taking a different perspective on cybersecurity performance

This presentation will introduce participants to key mental models on how to think about and understand safety from two of the leading voices in the discipline – Dr. Erik Hollnagel and Dr. Todd Conklin – and from there we ask the simple question of “how can we apply this to cybersecurity?” At the completion of this presentation attendees will be able to describe Dr. Hollnagel’s Safety-II approach and Dr. Conkiln’s definition of safety as “not the absence of accidents but the presence of effective defenses.” They will be able to explain how these ideas translate to the cybersecurity world broadly, and more specifically to operational technology cybersecurity where physical safety consequences are coupled to control system performance. Finally, participants will be able to identify how selected principles from Weick and Sutcliffe’s high reliability organization theory can help operationalize these key mental models around safety, for improved organizational cybersecurity over the long run.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2023

Cybersecurity Value-at-Risk Framework: Preprint

As more variable renewable energy sources are added to the grid, the critical role of hydropower as a reliable baseline and firming resource is rapidly growing. However, the U.S hydropower fleet is not fully prepared to face modern issues such as cybersecurity threats. Hydropower accounts for 37% of U.S. utility-scale renewable electricity but is challenged by diverse infrastructure and legacy devices that predate modern security practices. While new cybersecurity solutions cannot simply be added to current hydropower generation and operation technologies, custom cybersecurity assessments can reveal system-specific threats and risk probabilities and identify mitigating enhancements.

cybersecurity valuation↗
DOE OSTI2023

Software Bill of Materials in the Nuclear Industry

Nuclear power plants (NPP) have thousands of digital assets throughout their facility. Typically, NPPs have asset and configuration management programs that capture the make, model, and version of a component. This information, however, usually only includes first- or second-tier components and does not capture the complete enumeration of software components and their dependencies within operational technology (OT) equipment. As seen with recent cyberattacks, this level of detail is insufficient for identifying if and where an exploitable vulnerability exists within a facility. A software bill of materials (SBOM) provides this detailed enumeration. Further, integrating SBOMs with vulnerability data sources and vulnerability attestation reports can provide improved awareness leading to better cyber risk management and incident response. Preferably, SBOMs are provided by the supplier; however, when an NPP already owns a device, it is less likely they will have a supplier provided-SBOM. Fortunately, SBOMs can be generated on installed digital assets. This paper provides an introduction to the U.S. Department of Energy Office of Nuclear Energy paper titled “Towards Software Bill of Materials in the Nuclear Industry,” which describes the SBOM ecosystem and provides a suggested approach to methodically and seamlessly integrate an SBOM program in an NPP.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗