Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TEMPERATURE PROBE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Surface Measurement Techniques Temperature and Pressure Sensitive Paints

Luminescent molecular probes imbedded in a polymer binder form a temperature or pressure paint. On excitation by light of the proper wavelength, the luminescence,which is quenched either thermally or by oxygen, is detected by a camera or photodetector. From the detected luminescent intensity, temperature and pressure can be determined. Tl e basic photophysics, calibration, accuracy and the response of a luminescent paints is described followed by applications in wind tunnels and in rotating machinery.

Sullivan, John P.↗

Analytical and experimental study of supersonic combustion of hydrogen in a vitiated airstream

Detailed probe measurements of total temperature, pressure, and composition were taken in a two-dimensional test section 35.6 cm downstream of hydrogen injection. A high pressure gas generator supplied Mach 2.44 vitiated air or inert gas at elevated temperatures and at a static pressure equal to that of the hydrogen. Special water-cooled probes and sampling techniques were developed for the short test times required by heat-sink hardware. Independent methods of measuring stream total temperatures are compared. For the pure mixing case, the computed composition profile agreed well with the experimental profile. The analysis takes into account the wall boundary layer and the initial boundary layer in the main stream. Ignition of hydrogen, as determined from photographic exposures of the radiating gases, varied from 30 to 10 cm downstream from injection for a 45 K increase in local free-stream static temperature.

Burrows, M. C.↗

Thermal contrast in the atmosphere of Venus - Initial appraisal from Pioneer Venus probe data

The altitude profiles of temperature and pressure were measured during the descent of four Pioneer Venus probes, showing small contrasts below the clouds, but significant differences within the clouds at altitudes from 45 to 61 km. Measurements of pressure differences were found to be consistent with the cyclostrophic balance of zonal winds ranging from 110 to 150 m/sec at 60 km and from 43 to 77 m/sec at 40 km. The clouds were 10 to 20 K warmer than the extended profiles of the lower atmosphere and the middle cloud is convectively unstable. Both phenomena are due to thermal radiation from below. Meridional wind velocities were studied, concluding that significant planetary scale non-axisymmetric motions were present at latitudes below 30 degrees. This result was consistent with the day-night pressure difference. Indications of flow oscillations in the lower atmosphere were noted and the inference of wave motions in the lower atmosphere was supported by analysis of oscillations in the Doppler residuals.

Seiff, A.↗

Constraining Cometary Crystal Shapes from IR Spectral Features

A major challenge in deriving the silicate mineralogy of comets is ascertaining how the anisotropic nature of forsterite crystals affects the spectral features' wavelength, relative intensity, and asymmetry. Forsterite features are identified in cometary comae near 10, 11.05-11.2, 16, 19, 23.5, 27.5 and 33 microns [1-10], so accurate models for forsterite's absorption efficiency (Qabs) are a primary requirement to compute IR spectral energy distributions (SEDs, lambdaF lambda vs. lambda) and constrain the silicate mineralogy of comets. Forsterite is an anisotropic crystal, with three crystallographic axes with distinct indices of refraction for the a-, b-, and c-axis. The shape of a forsterite crystal significantly affects its spectral features [13-16]. We need models that account for crystal shape. The IR absorption efficiencies of forsterite are computed using the discrete dipole approximation (DDA) code DDSCAT [11,12]. Starting from a fiducial crystal shape of a cube, we systematically elongate/reduce one of the crystallographic axes. Also, we elongate/reduce one axis while the lengths of the other two axes are slightly asymmetric (0.8:1.2). The most significant grain shape characteristic that affects the crystalline spectral features is the relative lengths of the crystallographic axes. The second significant grain shape characteristic is breaking the symmetry of all three axes [17]. Synthetic spectral energy distributions using seven crystal shape classes [17] are fit to the observed SED of comet C/1995 O1 (Hale-Bopp). The Hale-Bopp crystalline residual better matches equant, b-platelets, c-platelets, and b-columns spectral shape classes, while a-platelets, a-columns and c-columns worsen the spectral fits. Forsterite condensation and partial evaporation experiments demonstrate that environmental temperature and grain shape are connected [18-20]. Thus, grain shape is a potential probe for protoplanetary disk temperatures where the cometary crystalline forsterite formed. The forsterite crystal shapes (equant, b-platelets, c-platelets, b-columns - excluding a- and c-columns) derived from our modeling [17] of comet Hale- Bopp, compared to laboratory synthesis experiments [18], suggests that these crystals are high temperature condensates. By observing and modeling the crystalline features in comet ISON, we may constrain forsterite crystal shape(s) and link to their formation temperature(s) and environment(s).

anisotropic crystal↗

Atmospheric Structure Investigation: Planetary in Situ Measurements of Atmospheric State Including Clouds/Aerosols.

The Atmospheric Structure Investigation (ASI) is a sensor suite designed for descent probes into planetary atmospheres, primarily aimed at Giant planets like Saturn and Uranus, and applicable to Venus, Titan, and Earth-specific missions. ASI aims to provide essential measurements of atmospheric structure, including probe acceleration, rotation, pressure, temperature, vertical winds, aerosol properties, and hydrogen and helium composition, crucial for contextualizing other probe data.

V Jha↗

Fiber optic temperature sensor

A temperature sensor has been developed that utilizes the temperature dependent absorption of a rare earth doped optical fiber. The temperature measurement is localized at a remote position by splicing a short section of the rare earth fiber into a loop of commercial data communication fiber that sends and returns an optical probe signal to the temperature sensitive section of fiber. The optical probe signal is generated from two different wavelength filtered LED sources. A four port fiber optic coupler combines the two separate wavelength signals into the fiber sensing loop. Time multiplexing is used so that each signal wavelength is present at a different time. A reference signal level measurement is also made from the LED sources and a ratio taken with the sensor signal to produce a transmission measurement of the fiber loop. The transmission is affected differently at each wavelength by the rare earth temperature sensitive fiber. The temperature is determined from a ratio of the two transmission measurements. This method eliminates any ambiguity with respect to changes in signal level in the fiber loop such as mating and unmating optical connectors. The temperature range of the sensor is limited to about 800 C by the temperature limit fo the feed fibers.

Morey, W. W.↗

Measurements of the Plasma Parameters and Low Frequency Oscillations in the Fisk Plasma Source

A new plasma device, the Fisk Plasma Source (FPS), has been developed at Fisk University. This plasma device is used to study the physics of low temperature plasmas and plasma-material interactions. The FPS device is a stainless steel vacuum 6-way cross vacuum vessel with at 10-inch inner diameter. Low temperature argon plasmas are generated using DC glow discharge and thermionic filament techniques. Spatial profiles of the plasma density, plasma potential, and electron temperature are measured using Langmuir probes. We present initial experimental measurements of density and temperature profiles in the FPS device. Experimental and theoretical studies of low frequency oscillations observed in the FPS device are also presented.

Thomas, Edward, Jr.↗

Graphite ablation at high temperatures

Graphite ablation under high temperatures for large outer planets entry probes, correlating mass loss rates with surface temperatures and specimen nose cone radii

Dickey, R. R.↗

A comparison of two rocket borne Langmuir probes having electrodes of different materials

The behavior of two types of Langmuir probes, one with electrodes made of low-sulfur stainless steel and one with electrodes made of aluminum coated with Aquadag, has been compared on two rocket flights. Each rocket payload included one Langmuir probe of each type. The electron temperatures measured with the stainless-steel electrodes were about 15% higher than the electron temperatures measured with the Aquadag-coated electrodes at 150 km on ascent and about 10% higher at 180 km. These results imply that the use of Aquadag coated electrodes or electrodes of other carefully chosen materials permits greater reliability in the measurement of electron temperatures in the ionosphere by the Langmuir probe technique.

Schutz, S. R.↗

Operational Characteristics and Plasma Measurements in a Low-Energy FARAD Thruster

Pulsed inductive plasma accelerators are spacecraft propulsion devices in which energy is stored in a capacitor and then discharged through an inductive coil. The device is electrodeless, inducing a plasma current sheet in propellant located near the face of the coil. The propellant is accelerated and expelled at a high exhaust velocity (order of 10 km/s) through the interaction of the plasma current with an induced magnetic field. The Faraday Accelerator with RF-Assisted Discharge (FARAD) thruster is a type of pulsed inductive plasma accelerator in which the plasma is preionized by a mechanism separate from that used to form the current sheet and accelerate the gas. Employing a separate preionization mechanism in this manner allows for the formation of an inductive current sheet at much lower discharge energies and voltages than those found in previous pulsed inductive accelerators like the Pulsed Inductive Thruster (PIT). In this paper, we present measurements aimed at quantifying the thruster's overall operational characteristics and providing additional insight into the nature of operation. Measurements of the terminal current and voltage characteristics during the pulse help quantify the output of the pulsed power train driving the acceleration coil. A fast ionization gauge is used to measure the evolution of the neutral gas distribution in the accelerator prior to a pulse. The preionization process is diagnosed by monitoring light emission from the gas using a photodiode, and a time-resolved global view of the evolving, accelerating current sheet is obtained using a fast-framing camera. Local plasma and field measurements are obtained using an array of intrusive probes. The local induced magnetic field and azimuthal current density are measured using B-dot probes and mini-Rogowski coils, respectively. Direct probing of the number density and electron temperature is performed using a triple probe.

Polzin, K. A.↗

Performance Evaluation of Particle Sampling Probes for Emission Measurements of Aircraft Jet Engines

Considerable attention has been recently received on the impact of aircraft-produced aerosols upon the global climate. Sampling particles directly from jet engines has been performed by different research groups in the U.S. and Europe. However, a large variation has been observed among published data on the conversion efficiency and emission indexes of jet engines. The variation results surely from the differences in test engine types, engine operation conditions, and environmental conditions. The other factor that could result in the observed variation is the performance of sampling probes used. Unfortunately, it is often neglected in the jet engine community. Particle losses during the sampling, transport, and dilution processes are often not discussed/considered in literatures. To address this issue, we evaluated the performance of one sampling probe by challenging it with monodisperse particles. A significant performance difference was observed on the sampling probe evaluated under different temperature conditions. Thermophoretic effect, nonisokinetic sampling and turbulence loss contribute to the loss of particles in sampling probes. The results of this study show that particle loss can be dramatic if the sampling probe is not well designed. Further, the result allows ones to recover the actual size distributions emitted from jet engines.

Lee, Poshin↗

Collisional Effects on Magnesium-rich Minerals found in Comets and Asteroids

While generally touted to be the least-altered bodies remaining from the age of the solar system's formation, comets and asteroids have undergone evolutionary processing throughout the 4.5-billion-year lifetime of the solar system. They have suffered the effects of collisions by impactors ranging in size from micrometeoroids to other comets and asteroids. As such, we must ask ourselves: can we detect these evolutionary effects remotely through telescopic observations? With this in mind, a suite of experiments were conducted, impacting magnesium-rich minerals as analogues to those that have been detected in the spectra of both asteroid surfaces and in the dust of cometary comae, including forsterite (Mg2SiO4, olivine), orthoenstatite (Mg2SiO3, pyroxene), diopside (MgCaSi2O6, monoclinic pyroxene), and magnesite (MgCO3, carbonate). These minerals were impacted at velocities ranging from 2.0 km/s to 2.8 km/s using the vertical gun in the Experimental Impact Laboratory (EIL) at NASA Johnson Space Center. These speeds mimic typical velocities of impacts occurring in the Kuiper belt [1]. Two classes of projectile were used: spherical alumina ceramic, whose density mimics that of rock, and cylinders made from the same material that they impacted (e.g., forsterite impactors for forsterite targets, etc.). The peak shock pressure varies significantly, depending on the target and impactor materials and the velocity; thus, shock effects differed in targets impacted at the same velocity but with compositionally different projectiles. The results indicate both: (a) how varying the impactor-density might change the outcome from a scientific viewpoint, as well as (b) possible contamination effects of the ceramic projectile in the resultant spectra of the target minerals from an experimental perspective. Temperature effects were also investigated by impacting samples at both 25 deg. and -25 deg. to: (a) probe whether the varying temperatures experienced by small bodies plays a role in the resultant spectra, and (b) constrain necessary experimental parameters. Analysis of Fourier Transform Infrared (FTIR) spectra obtained from the experimentally shocked materials shows clear indications of spectral shifts in wavelength, as well as a change in relative peak strengths of the spectral signatures at one wavelength compared with another, in all minerals except magnesite. Samples of the forsterite and orthoenstatite that displayed the spectral changes were examined with a transmission electron microscope, which revealed evidence of planar dislocations. The density of the dislocations in the experimentally shocked minerals mimicked the dislocation densities measured in both forsterite and enstatite grains recovered from Comet Wild 2 by the Stardust mission [2, 3, 4]. Further discussion on analyses of peak shock pressure and temperature-dependent effects can be found in Jensen et al., this meeting

Lederer, S.↗

Pressure and Temperature Sensitive Paint Measurements on Rotors

Luminescent molecular probes imbedded in a polymer binder form a temperature or pressure paint. On excitation by light of the proper wavelength, the luminescence, which is quenched either thermally or by oxygen, is detected by a camera or photodetector. From the detected luminescent intensity, temperature and pressure can be determined. The basic photophysics, calibration, accuracy and time response of luminescent paints is described followed by applications in wind tunnels and in rotating machinery.

Sullivan, John↗

Global empirical models of ionospheric electron temperature in the upper F-region and plasmasphere based on in situ measurements from the Atmosphere Explorer-C, ISIS-1 and ISIS-2 satellites

Langmuir probe measurements of electron temperature, T sub e, in the vicinity of 300, 400, 1400 and 3000 km from the Atmosphere Explorer-C and the ISIS satellites have been employed to construct empirical models of the global distribution of T sub e at each of these altitudes. Legendre polynomials are employed to describe the observations at solstice and equinox in terms of dip latitude and local time. Sources of T sub e variations, such as solar activity, magnetic activity and longitude are found to be of second order importance, although they are resolvable in some cases by comparisons of the data with the model. The behavior of T sub e at the altitudes of these models is discussed in terms of its implications for our understanding of the energy exchange between the F-region and the plasmasphere.

Brace, L. H.↗