SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A facile and scalable method to prepare graphene-based amphiphilic Janus nanosheets with high efficiency utilizing the formation of hydrogen bonding to immobilize graphene oxide (GO) on the surfaces of starch microspheres. After selective functionalization of the exposed surface using alkylamine, amphiphilic Janus nanosheets (AJN) were obtained by releasing the nanosheets from the starch microspheres.
A compound represented by Li a Co (1-x-2y) Me x (M1M2) y O δ , (Formula (I)) wherein Me, is one or more of Li, Mg, Al, Ca, Ti, Zr, V, Cr, Mn, Fe, Ni, Cu, Zn, Ru and Sn, and wherein 0≤x≤0.3, 0<y≤0.4, 0.95≤α≤1.4, and 1.90≤δ≤2.10 is disclosed. Further, particles including such compounds are described.
The present disclosure provide synthetic methods for the synthesis of N-substituted vinylidene and alkene compounds in addition to compounds formed from such methods.
Poster for the Carbon Dioxide Capture Review Meeting, Pittsburgh, PA, August 28-September 1, 2023.
For presentation at the 68th Annual Conference on Magnetism and Magnetic Materials, Dallas, TX, October 30-November 3, 2023.
Explore the source record for details and available documents.
Application of Polyurethane Science and Engineering to reduce ALARA conditions while securing Low Level Waste (LLW) loads for shipment within and between locations within the DOE complex. Potential reduction in cost as well. Interdepartmental collaborative efforts between new hires was established.
Degradable polyurethane foams can be an attractive material to use for packaging, transporting, and dispositioning of nuclear materials. This LDRD project explored the possibility of finding a suitable polyol component that would achieve the intended results. Significant improvements were made on the initial findings of a three month Visiting Faculty Program.
Explore the source record for details and available documents.
Metastable polymorphs of inorganic solids often possess material properties not present in the corresponding thermodynamic polymorphs, making them targets for the development of new functional materials. In contrast with isolating metastable bulk materials, syntheses of metastable polymorphs on the nanoscale are aided by fast non-equilibrium reaction kinetics and the favorable thermodynamic influence of surface energies, giving rise to greater ease of access to metastable high-temperature polymorphs and, in some cases, new polymorphs that do not exist in the bulk. The syntheses of metastable semiconductor nanocrystals are of interest for their potentially unique optoelectronic and physicochemical properties. However, in many material systems, synthesizing nanocrystalline products away from thermodynamic equilibrium in a predictable manner remains an outstanding challenge. This review outlines direct synthetic methodologies that have been developed to enable control over the nucleation and growth of metastable polymorphs of semiconductor nanocrystals by tailoring reaction conditions, precursor kinetics, ligand and surface effects, and other synthetic levers. The case studies reviewed herein expound on the direct syntheses of metastable ZnSe, Cu 2 SnSe 3 , CuInSe 2 , Ag 2 Se, and AgInSe 2 nanocrystals, and although there remain numerous examples of metastable nanocrystal syntheses outside of these metal chalcogenide systems, the concepts discussed are of general utility to the field of metastable nanocrystal syntheses as a whole. Explicit examples in which new functional properties are afforded by metastable polymorphs of the aforementioned material systems are presented within the context of applications for solar cells, photonics, and optical sensing. Finally, the factors that affect the kinetic persistence of metastable nanocrystalline polymorphs are discussed at length for these material systems.
Abstract Porphyrin dimers have been widely explored and studied owing to their importance in photosynthetic systems. A vast variety of dimers linked by different groups and at different angles have been synthesized and studied; however, the means by which to synthesize rigidly fused porphyrins with direct conjugation of the chromophores remains limited. Such a class of porphyrins may possess interesting properties that unconjugated or stacked dimers may not exhibit. In this study, bisbenzimidazole‐fused porphyrin dimers and their mono‐ and bis−zinc derivatives are synthesized and characterized. As a consequence of excitonic coupling, these dimers exhibit a split Soret band irrespective of the metal ion in the porphyrin cavity. Steady‐state fluorescence and excitation spectra followed by femtosecond transient absorption spectral studies of the heterometallated dimer, (free‐base and zinc porphyrin) reveals the occurrence of efficient singlet‐singlet energy transfer (>95 % efficiency and rate constant >10 12 s −1 ) within the dyad. Further, donor‐acceptor conjugates were formed by metal‐ligand axial coordination of phenyl imidazole functionalized C 60 and were characterized by a variety of physicochemical techniques. Excited state charge separation from both singlet and triplet excited states of ZnP in the conjugates has been established. The lifetime of the final charge‐separated state was in the 30–40 μs range revealing charge stabilization. Interestingly, no charge separation in the conjugate derived from the heterometallated dimer was observed wherein excitation transfer dominated the process. The present study brings out the importance of the rigid π‐spacer connecting porphyrin dimers in governing the energy and electron transfer events when coupled with an electron acceptor.
Here, we report the first synthesis of metal nanoparticles and supported metal nanoparticles on carbon by using hypergolic reactions. Specifically, we report the synthesis of noble metal nanoparticles (Pt, Ag, and Au) using sodium hydride (NaH) as both an ignition trigger and a reducing agent for the corresponding metal salt precursors. In addition, we report the one-step, in situ synthesis of Pt nanoparticles supported on carbon by adding sucrose as the carbon source. The hypergolically synthesized nanoparticles display elliptical morphology and are more crystalline compared with those conventionally synthesized in solution using sodium borohydride (NaBH 4 ). When tested as electrocatalysts, the hypergolic Pt nanoparticles exhibit more than 2 times higher specific electrochemical active surface area (ECSA) and a higher half-wave potential (E 1/2 ) of 0.94 V vs the reversible hydrogen electrode (RHE) compared to the conventionally synthesized ones. In addition, the electrocatalyst based on the in situ synthesized carbon that was decorated with the Pt nanoparticles synthesized hypergolically outperforms an analogous, state of the art, commercial PtC system. For example, the former shows an attractive E 1/2 (0.94 V) compared with 0.9 V for the commercial PtC. Accelerated durability tests (ADT) in an alkaline environment add another advantage. After 10 000 cycles, the hypergolically synthesized system shows a smaller reduction of E 1/2 and less degradation compared to the commercial PtC (10 mV compared to ∼30 mV). The work described here represents the first reported synthesis using hypergolic reactions of metal nanoparticles as well as supported metal nanoparticles. The properties of the resulting electrocatalysts demonstrate the versatility and promise of the new approach in materials synthesis and open new avenues for further investigation as electrocatalysts.
Cancer is one of the diseases with the highest mortality rate worldwide. Although PDT has recently produced encouraging outcomes, there are still many areas that need to be improved. The first of these is the negative consequences faced by patients treated with the PDT method when exposed to sunlight. For this reason, a new PDT method has been developed in recent years, and it is aimed at using photosensitizer molecules that can be active in acidic conditions. Since the pH values of tumor tissues are more acidic than normal tissues, preparing molecules that act effectively in acidic conditions will allow for more effective results in treating cancer with PDT. In this context, within the scope of this study, 3‐(4‐propionylphenoxy)phthalonitrile ( 1 ) and its non‐peripheral tetra‐substituted phthalocyanine derivatives [( 2 ), ( 3 ), and ( 4 )] were prepared. With these phthalocyanine derivatives, the novel compounds ( 5 ), ( 6 ), and ( 7 ) were synthesized for the first time. The aggregation tendencies of newly synthesized phthalocyanines ( 5–7 ) were investigated in solvent media. The effects of pH changes upon UV–Vis and fluorescence spectra were performed. The electronic and emission spectra of synthesized phthalocyanine derivatives are highly sensitive to pH changes. Formation constant (Log K) values of mono‐ and di‐protonated phthalocyanine forms were calculated by the Henderson–Hasselback equation. The mono‐ and di‐protonated species' equilibrium constants (logK 1 and logK 2 ) were calculated as ~5.0. This value may be promising for pH‐sensitizing photosensitizers. Also, the photophysical and photochemical properties of synthesized metallophthalocyanine derivatives ( 2 ) and ( 5 ) were studied at different pH values. The singlet oxygen quantum yield of ( 2 ) and ( 5 ) was calculated to be 0.78 and 0.81 in DMSO, respectively. When pH = 6.4, that is, tumor‐pH‐values, this value for ( 5 ) has increased to 0.92. The newly synthesized phthalocyanines are suitable photosensitizers for PDT applications, especially with high singlet oxygen quantum yield at pH 6.4.
Synthesis of all-inorganic metal oxide architectures using polymer templates offers control over their thickness, porosity, and composition. Here, in this study, we provide insights into the synthesis of nanoporous zinc oxide films as a model system via infiltration of polymers that have different mechanisms of interaction with metal oxide precursors such as a polymer of intrinsic microporosity (PIM-1) and representative of the block-copolymers family (polystyrene-polyvinyl pyridine block copolymer). We investigated polymer infiltration process with both gas (diethyl zinc, DEZ, and water vapors) and solution (zinc acetylacetonate, Zn(acac) 2 , dissolved in ethanol) phase precursors. Using quartz crystal microbalance (QCM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS) analyses, we systematically studied the effect of polymer template and the form of the metal oxide precursors on the properties of synthesized metal oxide thin coatings. We demonstrate that the infiltration of polymer templates can be efficiently achieved using both gas phase and solution phase precursors. We show that the crystallinity of the synthesized 200 nm ZnO films is mainly affected by the state of the precursor (gas or solution phase) and does not depend on the polymer template type. In turn, the polymer type affects the surface termination of ZnO films. We demonstrate that the surface of porous ZnO coatings synthesized with BCP (here PS-P4VP) is more accessible than the surface of ZnO synthesized with PIM; however, despite the lower surface accessibility for ethanol molecules, ZnO synthesized via infiltration of PIM-1 with solution-phase precursors demonstrates the largest change in resistivity upon its exposure to ethanol vapor at room temperature.
We here investigate how the synthesis method affects the crystallite size and atomic structure of cobalt iron oxide nanoparticles. By using a simple solvothermal method, we first synthesized cobalt ferrite nanoparticles of ca. 2 and 7 nm, characterized by Transmission Electron Microscopy (TEM), Small Angle X-ray scattering (SAXS), X-ray and neutron total scattering. The smallest particle size corresponds to only a few spinel unit cells. Nevertheless, Pair Distribution Function (PDF) analysis of X-ray and neutron total scattering data shows that the atomic structure, even in the smallest nanoparticles, is well described by the spinel structure, although with significant disorder and a contraction of the unit cell parameter. These effects can be explained by the surface oxidation of the small nanoparticles, which is confirmed by X-ray near edge absorption spectroscopy (XANES). Neutron total scattering data and PDF analysis reveal a higher degree of inversion in the spinel structure of the smallest nanoparticles. Neutron total scattering data also allow magnetic PDF (mPDF) analysis, which shows that the ferrimagnetic domains correspond to ca. 80% of the crystallite size in the larger particles. A similar but less well-defined magnetic ordering was observed for the smallest nanoparticles. Finally, we used a co-precipitation synthesis method at room temperature to synthesize ferrite nanoparticles similar in size to the smallest crystallites synthesized by the solvothermal method. Structural analysis with PDF demonstrates that the ferrite nanoparticles synthesized via this method exhibit a significantly more defective structure compared to those synthesized via a solvothermal method.
The siderophore rhizoferrin (N 1 ,N 4 -dicitrylputrescine) is produced in fungi and bacteria to scavenge iron. Putrescine-producing bacterium Ralstonia pickettii synthesizes rhizoferrin and encodes a single nonribosomal peptide synthetase-independent siderophore (NIS) synthetase. From biosynthetic logic, we hypothesized that this single enzyme is sufficient for rhizoferrin biosynthesis. We confirmed this by expression of R. pickettii NIS synthetase in Escherichia coli, resulting in rhizoferrin production. This was further confirmed in vitro using the recombinant NIS synthetase, synthesizing rhizoferrin from putrescine and citrate. Heterologous expression of homologous lbtA from Legionella pneumophila, required for rhizoferrin biosynthesis in that species, produced siderophore activity in E. coli. Rhizoferrin is also synthesized by Francisella tularensis and Francisella novicida, but unlike R. pickettii or L. pneumophila, Francisella species lack putrescine biosynthetic pathways because of genomic decay. Francisella encodes a NIS synthetase FslA/FigA and an ornithine decarboxylase homolog FslC/FigC, required for rhizoferrin biosynthesis. Ornithine decarboxylase produces putrescine from ornithine, but we show here in vitro that FigA synthesizes N-citrylornithine, and FigC is an N-citrylornithine decarboxylase that together synthesize rhizoferrin without using putrescine. We co-expressed F. novicida figA and figC in E. coli and produced rhizoferrin. A 2.1 Å X-ray crystal structure of the FigC N-citrylornithine decarboxylase reveals how the larger substrate is accommodated and how active site residues have changed to recognize N-citrylornithine. FigC belongs to a new subfamily of alanine racemase-fold PLP-dependent decarboxylases that are not involved in polyamine biosynthesis. These data reveal a natural product biosynthetic workaround that evolved to bypass a missing precursor and re-establish it in the final structure.
The experimental isolation of graphene led to the discovery of an entirely new world of two-dimensional (2D) materials in which the 2D nature often leads to emergent behaviors not seen in bulk systems. 2D transition metal dichalcogenides (TMDs) exhibit physico-chemical properties that depend on the transition metal, polymorph, thickness, and presence and type of defects. Recently, a group of thin (10-100nm) transition metal carbides (TMCs), such as Mo2C, has been synthesized that exhibit a thickness-dependent superconducting critical temperature (Tc). These thin TMCs are different from MXenes, another class of 2D materials consisting of few layers of nitrides or carbides (<5nm) produced by chemical etching and delamination. The goal of this renewal proposal is to combine experiment and computation to synthesize and elucidate the guiding principles that control the growth, orientation and strain of heterostacks of thin TMCs and TMDs composed with Nb, Ti and W. We expect to stabilize metastable hybrid phases of TMCs sandwiched between TMDs (H-TMD/Cs) with unprecedented physico-chemical properties. As part of previous DOE-funded work by the Terrones/Sinnott groups, thin (10-100 nm thick) Mo2C flakes were successfully synthesized by chemical vapor deposition (CVD). By subsequently exposing Mo2C to H2S, partial chalcogenization was achieved, resulting in heterostacks of MoCx phases and MoS2. The formation of MoS2 led to a deficiency of Mo atoms in the underlying Mo2C, resulting in an inhomogeneous phase change from α-Mo2C to γ’-MoCx and then to γ-MoC. The γ’-MoCx is a strained metastable phase and the heterostack of all three phases demonstrated an increased Tc relative to that of α-Mo2C, from 4 to 6K; its interleaved layered structure consisting of superconducting and semiconducting phases is ideal for future studies of Josephson junction series arrays. Moiré patterns in these heterostacked systems could result in new phenomena, as moiré patterns in bilayer graphene showed unconventional superconductivity and moiré excitons have been observed in twisted TMD heterobilayers. The scientific hypothesis of the proposed synergistic computational and experimental research is that orientation and strain control within confined thin metastable TMCs, sandwiched by stable phases of TMCs and layered TMDs, will depend on kinetic and thermodynamic “knobs” that include fast temperature changes, chalcogen diffusion through preferred crystallographic planes, reaction times, pressure, reactive atmosphere, precursors, and surfactants, which will also tailor properties such as superconductivity, magnetism, ferroelectricity, piezoelectricity, and catalytic performance. We will develop the guiding principles for the synthesis and stabilization of metastable H-TMD/Cs based on Nb, Ti and W. In order to validate the hypothesis, four tasks are proposed: The first task will synthesize ultra-thin TMCs based on Nb, W and Ti, by: 1) adapting the CVD method used for Mo2C, 2) plasma assisted CVD, 3) defect-mediated CVD processes, and 4) cryo-milling of carbide powders. The second task will accomplish the synthesis and basic physico-chemical characterizations of H-TMD/Cs by chalcogenization of the materials synthesized in task one, and by carbonization of TMDs. H-TMD/Cs will also be investigated for their suitability in energy conversion applications such as supercapacitors, Li and multivalent ion batteries, and electrocatalysts, topics of interest to DoE. These tasks will be carried out in close conjunction with density functional theory (DFT) calculations with insights into energetics, lattice parameters, stability, phase diagrams, band structures, and density of states of H-TMD/Cs. The third task will characterize and evaluate strain and moiré patterns at the interfaces of different H-TMD/Cs by high-resolution scanning transmission electron microscopy (HR-STEM), scanning tunneling microscopy (STM), and conductive tip atomic force microscopy. Nudged elastic band calculations with DFT will be performed to understand the chalcogen diffusion process, which will provide insights into the interfaces between different phases of TMCs and TMDs. The fourth task aims at quantifying the stability and dynamics of H-TMD/Cs by in-situ TEM and Raman studies under heating, strain, and electrical biasing. Phonon calculations using DFT will provide a basis for interpreting Raman spectra. This coherent framework involving synthesis, characterization, and computation will result in a broad scientific impact for energy related applications. The ability to develop new H-TMD/Cs will enhance a range of applications that include batteries, catalysts, switches, sensors, quantum computing components and smart coatings.
The experimental isolation of graphene led to the discovery of an entirely new world of two-dimensional (2D) materials in which the 2D nature often leads to emergent behaviors not seen in bulk systems. 2D transition metal dichalcogenides (TMDs) exhibit physico-chemical properties that depend on the transition metal, polymorph, thickness, and presence and type of defects. Recently, a group of thin (10-100nm) transition metal carbides (TMCs), such as Mo 2 C, has been synthesized that exhibit a thickness-dependent superconducting critical temperature (Tc). These thin TMCs are different from MXenes, another class of 2D materials consisting of few layers of nitrides or carbides (<5nm) produced by chemical etching and delamination. The goal of this renewal proposal is to combine experiment and computation to synthesize and elucidate the guiding principles that control the growth, orientation and strain of heterostacks of thin TMCs and TMDs composed with Nb, Ti and W. We expect to stabilize metastable hybrid phases of TMCs sandwiched between TMDs (H-TMD/Cs) with unprecedented physico-chemical properties. As part of previous DOE-funded work by the Terrones/Sinnott groups, thin (10-100 nm thick) Mo 2 C flakes were successfully synthesized by chemical vapor deposition (CVD). By subsequently exposing Mo 2 C to H 2 S, partial chalcogenization was achieved, resulting in heterostacks of MoCx phases and MoS 2 . The formation of MoS 2 led to a deficiency of Mo atoms in the underlying Mo 2 C, resulting in an inhomogeneous phase change from α-Mo 2 C to γ’-MoCx and then to γ-MoC. The γ’-MoCx is a strained metastable phase and the heterostack of all three phases demonstrated an increased Tc relative to that of α-Mo 2 C, from 4 to 6K; its interleaved layered structure consisting of superconducting and semiconducting phases is ideal for future studies of Josephson junction series arrays. Moiré patterns in these heterostacked systems could result in new phenomena, as moiré patterns in bilayer graphene showed unconventional superconductivity and moiré excitons have been observed in twisted TMD heterobilayers. The scientific hypothesis of the proposed synergistic computational and experimental research is that orientation and strain control within confined thin metastable TMCs, sandwiched by stable phases of TMCs and layered TMDs, will depend on kinetic and thermodynamic “knobs” that include fast temperature changes, chalcogen diffusion through preferred crystallographic planes, reaction times, pressure, reactive atmosphere, precursors, and surfactants, which will also tailor properties such as superconductivity, magnetism, ferroelectricity, piezoelectricity, and catalytic performance. We will develop the guiding principles for the synthesis and stabilization of metastable H-TMD/Cs based on Nb, Ti and W. In order to validate the hypothesis, four tasks are proposed: The first task will synthesize ultra-thin TMCs based on Nb, W and Ti, by: 1) adapting the CVD method used for Mo 2 C, 2) plasma assisted CVD, 3) defect-mediated CVD processes, and 4) cryo-milling of carbide powders. The second task will accomplish the synthesis and basic physico-chemical characterizations of H-TMD/Cs by chalcogenization of the materials synthesized in task one, and by carbonization of TMDs. H-TMD/Cs will also be investigated for their suitability in energy conversion applications such as supercapacitors, Li and multivalent ion batteries, and electrocatalysts, topics of interest to DoE. These tasks will be carried out in close conjunction with density functional theory (DFT) calculations with insights into energetics, lattice parameters, stability, phase diagrams, band structures, and density of states of H-TMD/Cs. The third task will characterize and evaluate strain and moiré patterns at the interfaces of different H-TMD/Cs by high-resolution scanning transmission electron microscopy (HR-STEM), scanning tunneling microscopy (STM), and conductive tip atomic force microscopy. Nudged elastic band calculations with DFT will be performed to understand the chalcogen diffusion process, which will provide insights into the interfaces between different phases of TMCs and TMDs. The fourth task aims at quantifying the stability and dynamics of H-TMD/Cs by in-situ TEM and Raman studies under heating, strain, and electrical biasing. Phonon calculations using DFT will provide a basis for interpreting Raman spectra. This coherent framework involving synthesis, characterization, and computation will result in a broad scientific impact for energy related applications. The ability to develop new H-TMD/Cs will enhance a range of applications that include batteries, catalysts, switches, sensors, quantum computing components and smart coatings.