Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Secondary wall”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

MELCOR Accident Progression and Source Term Demonstration Calculations for a FHR

MELCOR is an integrated thermal hydraulics, accident progression, and source term code for reactor safety analysis that has been developed at Sandia National Laboratories for the United States Nuclear Regulatory Commission (NRC) since the early 1980s. Though MELCOR originated as a light water reactor (LWR) code, development and modernization efforts have expanded its application scope to include non-LWR reactor concepts. Current MELCOR development efforts include providing the NRC with the analytical capabilities to support regulatory readiness for licensing non-LWR technologies under Strategy 2 of the NRC's near- term Implementation Action Plans. Beginning with the Next Generation Nuclear Project (NGNP), MELCOR has undergone a range of enhancements to provide analytical capabilities for modeling the spectrum of advanced non-LWR concepts. This report describes the generic plant model developed to demonstrate MELCOR capabilities to perform fluoride-salt-cooled high-temperature reactor (FHR) safety evaluations. The generic plant model is based on publicly-available FHR design information. For plant aspects (e.g., reactor building leak rate and details of the cover-gas system) that are not described in the FHR references, the analysts made assumptions needed to construct a MELCOR full-plant model. The FHR model uses a TRi-structural ISOtropic (TRISO)-particle fuel pebble-bed reactor with a primary system rejecting heat to two coiled tube air heat ex changers. Three passive direct reactor auxiliary cooling systems provide heat removal to supplement or replace the emergency secondary system heat removal during accident conditions. Surrounding the reactor vessel is a low volume reactor cavity that insulates the reactor with fire bricks and thick concrete walls. A refractory reactor liner system provides water cooling to reduce the concrete wall temperatures. Example calculations are performed to show the plant response and MELCOR capabilities to characterize a range of accident conditions. The accidents selected for evaluation consider a range of degraded and failed modes of operation for key safety functions providing reactivity control, the primary system decay heat removal and also a piping leak of the line to the coolant drain tank.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Editorial: Wood Development and Physiology in a Changing Climate

Wood of forest trees is a renewable, sustainable and easily workable material and has been widely used in construction, paper making, furniture, and as a feedstock for biofuels. Wood formation is the result of a highly ordered and finely regulated process. Secondary xylem (wood) and phloem are the inner and outer derivative products of the vascular cambium, respectively. Xylem is mainly composed of dead cells with thickened cell walls rich in cellulose, hemicelluloses, and lignin, which are responsible for providing mechanical support and conducting water and minerals for the trees. Phloem transports photoassimilates and signaling molecules, including phytohormones and peptides. Wood structure varies greatly between, and within, tree species. A thorough understanding of developmental processes and metabolic pathways during wood formation would provide a basis for improving wood biomass and modifying properties in forest trees.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Stacking Faults Originating from Star-Defects in 4H-SiC

Intense efforts are currently in progress to study various sources of basal plane dislocations (BPDs) in SiC epitaxial layers. BPDs can generate Shockley-type stacking faults (SSFs) in SiC epitaxial layers, which have been shown to be associated with the degradation of power devices. This study shows that the star-shaped defect can be a source of several BPDs in the epitaxial layer. We investigate the complex microstructure of the star defect, the generation of BPDs, and expansion of SSFs using various complementary microscopy and optical techniques. We show direct evidence that star-defects can be a nucleation point of single-SSFs that can expand at the core of the defect. Newly found secondary dislocation arrays extending over a few centimeters away are found to be emanating from the primary arms of the star defect. The presence of such dislocation walls and the expansion of single-SSFs will affect the yield of numerous die on a wafer. Further understanding of the formation mechanism of stacking faults generated from star-defects as provided in this study helps understand their effect on SiC-based devices, which is crucial to assess device reliability.

36 MATERIALS SCIENCE↗
NASA NTRS1993

Additional support for the TDK/MABL computer program

An advanced version of the Two-Dimensional Kinetics (TDK) computer program was developed under contract and released to the propulsion community in early 1989. Exposure of the code to this community indicated a need for improvements in certain areas. In particular, the TDK code needed to be adapted to the special requirements imposed by the Space Transportation Main Engine (STME) development program. This engine utilizes injection of the gas generator exhaust into the primary nozzle by means of a set of slots. The subsequent mixing of this secondary stream with the primary stream with finite rate chemical reaction can have a major impact on the engine performance and the thermal protection of the nozzle wall. In attempting to calculate this reacting boundary layer problem, the Mass Addition Boundary Layer (MABL) module of TDK was found to be deficient in several respects. For example, when finite rate chemistry was used to determine gas properties, (MABL-K option) the program run times became excessive because extremely small step sizes were required to maintain numerical stability. A robust solution algorithm was required so that the MABL-K option could be viable as a rocket propulsion industry design tool. Solving this problem was a primary goal of the phase 1 work effort.

Nickerson, G. R.↗
NASA NTRS2010

Secondary Impacts on Structures on the Lunar Surface

The Altair Lunar Lander is being designed for the planned return to the Moon by 2020. Since it is hoped that lander components will be re-used by later missions, studies are underway to examine the exposure threat to the lander sitting on the Lunar surface for extended periods. These threats involve both direct strikes of meteoroids on the vehicle as well as strikes from Lunar regolith and rock thrown by nearby meteorite strikes. Currently, the lander design is comprised of up to 10 different types of pressure vessels. These vessels included the manned habitation module, fuel, cryogenic fuel and gas storage containers, and instrument bays. These pressure vessels have various wall designs, including various aluminum alloys, honeycomb, and carbon-fiber composite materials. For some of the vessels, shielding is being considered. This program involved the test and analysis of six pressure vessel designs, one of which included a Whipple bumper shield. In addition to the pressure vessel walls, all the pressure vessels are wrapped in multi-layer insulation (MLI). Two variants were tested without the MLI to better understand the role of the MLI in the impact performance. The tests of performed were to examine the secondary impacts on these structures as they rested on the Lunar surface. If a hypervelocity meteor were to strike the surface nearby, it would throw regolith and rock debris into the structure at a much lower velocity. Also, when the manned module departs for the return to Earth, its rocket engines throw up debris that can impact the remaining lander components and cause damage. Glass spheres were used as a stimulant for the regolith material. Impact tests were performed with a gas gun to find the V50 of various sized spheres striking the pressure vessels. The impacts were then modeled and a fast-running approximate model for the V50 data was developed. This model was for performing risk analysis to assist in the vessel design and in the identification of ideal long-term mission sites. This paper reviews the impact tests and analysis and modeling examining the impact threat to various components in the lander design.

Christiansen, Eric↗
NASA NTRS1972

Analysis and testing of compressible flow ejectors with variable area mixing tubes.

An analytical model has been developed to predict the flow behavior within axisymmetric single-nozzle ejectors employing variable-area mixing tubes. The primary flow may be supersonic or subsonic and may have a different stagnation temperature from the subsonic secondary flow. Tests were performed on an ejector with an 800 F supersonic (M = 2.72) primary jet to evaluate the analytical model. Measured velocity profiles, temperature profiles, and wall static pressure distributions are presented and compared to the analytical predictions. Agreement is generally good.

Hickman, K. E.↗
NASA NTRS1994

Steady Secondary Momentum and Enthalpy Streaming in the Pulse Tube Refrigerator

Our study investigates the steady secondary streaming that occurs in the pulse tube refrigerator through application of the conservation laws and support by flow visualization experiments. A series expansion of the mass, momentum and energy conservation laws for an axisymmetric system yields a set of linear differential equations. The series solution is expanded in the small parameter epsilon = 1/Str where Str is the Strouhal number. The O(1) basic flow problem is solved for the case of a compressible ideal gas oscillating within a cylindrical tube. The phase and amplitude of the boundary conditions on axial velocity are treated as independent parameters. The basic solution for the gas domain is solved for the case of temperature and heat flux coupling to the tube wall. The temperature coupled solution shows how the Fourier number of the tube wall affects the gas temperature, phase angle, and time-averaged enthalpy flow. The basic solution is also examined for the time-averaged Reynolds stresses which are shown to be the driving force that produces steady secondary momentum streaming. Calculated solutions to the steady momentum streaming are shown to be in qualitative agreement with flow visualization experiments.

Lee, J. M.↗
DOE OSTI2022

Modeling of vapor-liquid interactions in condensing ejectors

Ejectors are compact mechanical devices that utilize the expansion of a high-pressure primary fluid to entrain and compress a low-pressure secondary fluid by means of momentum transfer between the two streams of fluid. Condensing ejectors feature both momentum and heat transfer through the interaction between the vapor and liquid streams. The goal of this paper is to develop and validate a one-dimensional slug flow model to simulate the vapor–liquid interactions in two types of condensing ejectors – one with primary liquid and secondary vapor flows (Type I), and the other with primary vapor and secondary liquid flows (Type II). Control volume analysis of the mass, momentum, and energy balance in each phase and across the interface was conducted for the ejectors. The slug flow models for both types of ejectors are validated with published results in the literature. The friction coefficient on the inner wall of the ejectors and the interfacial heat transfer coefficient are identified as controlling parameters for the ejector performance in terms of pressure and temperature distributions along the axis. The detailed parametric study shows that the liquid inlet velocity and mixing tube diameter have a significant impact on the performance of the Type I ejectors, and the performance of the Type II ejectors is mainly controlled by the secondary liquid flow inlet temperature.

42 ENGINEERING↗
NASA NTRS1975

Experimental results for the transpired turbulent boundary layer in an adverse pressure gradient

The fluid mechanics of transpired incompressible turbulent boundary layers under zero and adverse pressure gradient conditions is investigated using an open-ended wind tunnel with a porous floor in the test section and a secondary air system for supply and metering of the transpiration air. All velocity profiles and turbulence profiles are obtained by linearized constant-temperature hot-wire anemometry. The wall shear stress is determined by measuring the shear stress away from the wall and extrapolating to the wall by integrating the boundary layer equations for the shear-stress profile. Equilibrium boundary layers are obtained when the transpiration velocity is varied such that the blowing parameter and the Clauser pressure gradient parameter are held constant. The experimental results obtained are presented in tabular and graphical forms.

Andersen, P. S.↗
NASA NTRS1984

Apparatus for measuring charged particle beam

An apparatus to measure the incident charged particle beam flux while effectively eliminating losses to reflection and/or secondary emission of the charged particle beam being measured is described. It comprises a sense cup through which the charged particle beam enters. A sense cone forms the rear wall of the interior chamber with the cone apex adjacent the entry opening. An outer case surrounds the sense cup and is electrically insulated therefrom. Charged particles entering the interior chamber are trapped and are absorbed by the sense cup and cone and travel through a current measuring device to ground.

Gregory, D. A.↗
NASA NTRS1954

A Visualization Study of Secondary Flows in Cascades

Flow-visualization techniques are employed to ascertain the streamline patterns of the nonpotential secondary flows in the boundary layers of cascades, and thereby to provide a basis for more extended analyses in turbomachines. The three-dimensional deflection of the end-wall boundary layer results in the formation of a vortex within each cascade passage. The size and tightness of the vortex generated depend upon the main-flow turning in the cascade passage. Once formed, a vortex resists turning in subsequent blade rows, with consequent unfavorable angles of attack and possible flow disturbances on the pressure surfaces of subsequent blade rows when the vortices impinge on these surfaces. Two major tip-clearance effects are observed, the formation of a tip-clearance vortex and the scraping effect of a blade with relative motion past the wall boundary layer. The flow patterns indicate methods for improving the blade tip-loading characteristics of compressors and of low- and high-speed turbulence.

Herzig, Howard Z↗
NASA NTRS1999

Swept-Wing Receptivity Studies Using Distributed Roughness

Transition to turbulence in swept-wing flows has resisted correlation with linear theory because of its sensitivity to freestream conditions and 3-D roughness and because one of the principal instability modes quickly 'becomes nonlinear. In the face of such a formidable problem, two rather long-term fundamental efforts have been underway at DLR Gottinberg and Arizona State University that address swept-wing transition. These efforts have been recently reviewed by Bippes (1997) and Reibert and Saric (1997). Thus, the present work is a continuation of a series of studies on swept-wing boundary layers which have led to a better understanding of the transition process. In particular, we have taken advantage of the sensitivity to 3-D roughness and the modal nature of the instability in order to propose a particular control strategy. Complementing the two aforementioned reviews, general reviews of the swept-wing transition problem are found in Arnal (1997) and Kachanov (1996). Other recent reviews include Reshotko (t997), Crouch (1997), and Herbert (1997a,b). The failure of linear theory is discussed in Reed et al. (1996). The historical work is found in Reed and Sar-ic (1989). The basic idea is that the combination of sweep and chordwise pressure gradient within the boundary layer creates a velocity component perpendicular to the inviscid streamline. This crossflow profile is inflectional and exhibits both traveling and stationary unstable waves called crossflow vortices that are (approximately) aligned along the inviscid streamlines. Under conditions of low freestream turbulence levels, the dominant crossflow wave is stationary (Reibert and Saric t997) while moderate to high turbulence levels initiate dominant traveling waves (Dehle and Bippes 1996; Bippes 1997). 'Me mechanism is relatively insensitive to sound and 2-D surface roughness (Radeztsky et al. 1993) but very sensitive to 3-D roughness near the attachment line. We concentrate our work on low-turbulence freestream flows and stationary crossflow waves. Although the v' and w' components of the disturbances are very small, by convecting streamwise momentum in the wall-normal direction, they produce 0(l) changes inu'.Thus the mean flow is highly distorted with localized inflection points. Transition is then triggered by a high-frequency secondary instability of the distorted mean profile.

Saric, William S.↗
NASA NTRS1986

Performance of the high speed anechoic wind tunnel at Lyon University

The characteristics of the feed duct, the wind tunnel, and the experiments run in the convergent-divergent anechoic wind tunnel at Lyon University are described. The wind tunnel was designed to eliminate noise from the entrance of air or from flow interactions with the tunnel walls so that noise caused by the flow-test structure interactions can be studied. The channel contains 1 x 1 x 0.2 m glass and metal foil baffles spaced 0.2 m apart. The flow is forced by a 350 kW fan in the primary circuit, and a 110 kW blower in the secondary circuit. The primary circuit features a factor of four throat reductions, followed by a 1.6 reduction before the test section. Upstream and downstream sensors permit monitoring of the anechoic effectiveness of the channel. Other sensors allow modeling of the flow structures in the tunnel. The tunnel was used to examine turbulent boundary layers in flows up to 140 m/sec, tubulence-excited vibrations in walls, and the effects of laminar and turbulent flows on the appearance and locations of noise sources.

Sunyach, M.↗
DOE OSTI2023

Shear Assisted Processing and Extrusion of Unhomogenized Aluminum Alloy 6063 Castings with High Iron Content

Shear Assisted Processing and Extrusion (ShAPE) was used to fabricate aluminum 6063 tubing directly from secondary scrap. Trimmings from an automotive manufacturing facility were cast into billets spiked with iron (0.3 wt% Fe) to explore the tolerance of ShAPE to Fe contamination. Billets were extruded in the unhomogenized condition to form tubing with an outer diameter of 12 mm and wall thickness of 2 mm. Tensile properties reached 0.2% YS = 206 MPa, UTS = 238 MPa, and U.E. = 16.3% in the T6 temper. Performance exceeds the ASTM minimum standard and is on par with ASM typical values for conventional extrusion of primary aluminum billets in the fully homogenized condition. Microstructural characterization shows extensive refinement of grain size along with dispersion and refinement of Fe-Al-Si intermetallic phases. This study suggests that ShAPE extrusion may offer a lower carbon manufacturing pathway through direct recycling of secondary aluminum scrap and elimination of the billet homogenization step.

solid phase processing, AA 6063, extrusion, Shear ↗
DOE OSTI2025

Elucidating the effect of minor-actinide addition on fuel-cladding chemical interaction in an HT-9 clad U-Pu-Zr metallic fuel irradiated to 6.15 at.% burnup in EBR-II

Scanning and transmission electron microscopy (S/TEM) were used to characterize the local fuel-cladding chemical interaction (FCCI) in one cross-section taken from a HT-9 clad U-20.3Pu-10Zr-1.2Am-1.3Np (in wt.%) fuel irradiated to 6.15 at.% burnup with inner cladding temperatures ranging between 460–490 °C. Results showed that the total interaction thickness between fuel and cladding was <10 µm. Fe infiltrated the fuel to form U-Zr-Fe phases while fuel elements or lanthanides did not infiltrate into the cladding. Np was not involved in the formation of any phases in the examined locations; however, Am played a role by forming a ∼2 µm thick homogeneous Fe-Pu-Am planar front at the inner cladding wall. An oxidized Na layer existed in the fuel-cladding gap with Fe and lanthanide particles dispersed within, suggesting Na could facilitate the transport of fuel and cladding constituents. Secondary phases, including an FCC Zr-rich phase, lanthanide phases, and α’-Cr(Fe) were identified in the outer fuel and FCCI regions. Furthermore, this study suggests that, for the irradiation conditions specific to this cross-section, minor actinides have little impact on FCCI behavior beyond what would be observed in typical HT-9 clad U-Pu-Zr fuel pins systems.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Direct numerical simulation of open-channel flow over a heterogeneous particle bed at low relative submergence

In this article, this study investigates turbulent open-channel flows over beds of irregularly arranged particles, using direct numerical simulations at a friction Reynolds number of Re T = 300⁠. Two distinct cases are examined: a polydisperse bed (P800) composed of multiple layers of randomly distributed spheres of varying sizes, and a monodisperse bed (M1015) formed by a random distribution of uniform sized spheres, with a bottommost single layer of varied-sized particles to introduce realistic randomness. Our investigation unveils a rich network of low- and high-speed streaks within the flow field, exhibiting distinctive behaviors in different bed configurations. The P800 case presents a poorly organized flow pattern induced by the varied particle sizes and arrangements, while the M1015 case shows a more regular flow pattern, marked by larger streaks. We also observe that total wall shear stress is substantially influenced by surface roughness-induced drag, extending beyond the effects documented in existing studies of open-channel flows. The present study reveals intricate secondary flow patterns over irregular particle beds. Large-scale circulations are discerned around particle crests in the P800 case and localized circulations with increased turbulence in the M1015 case. Furthermore, analysis of Reynolds stress tensor components indicates that roughness disrupts coherent turbulent eddies, consequently mitigating peak stress. We quantify correlations between drag force and local fluid velocity fluctuations. Notably, a larger deviation in drag is observed in the P800 case compared to M1015, accentuating the influence of particle size and distribution on fluid–particle interactions.

42 ENGINEERING↗
NASA NTRS1974

Smooth plains and continuous deposits of craters and basins

Apollo 16 photographic data are analyzed which suggest that smooth plains are related in origin to large primary cratering events, and that the plains material is mainly the ejecta of local and regional primary impact craters with only minor contributions from distant craters and basins. This material, then, has been emplaced in its present location by secondaries of distant craters and directly by primary craters near the site. Calculations indicate that the material excavated from large primary craters typically excavates much larger amounts of material from local terrain when it impacts in the secondary crater field. There is a correlation between the extent of development of smooth plains inside large high-land craters and the erosional state of the crater rims and walls. It is incorrect to consider the continuous deposits to be solely basin ejecta.

Oberbeck, V. R.↗
NASA NTRS1990

Advanced meteoroid and debris shielding concepts

The results of the shielding screening and optimization work conducted at the NASA Johnson Space Center Hypervelocity Impact Research Laboratory (HIRL) are described. The impact tests to investigate and optimize certain aspects of the aluminum mesh double-bumper concept, which was considered the best performer in the screening test, are analyzed. Preliminary results indicate that the aluminum mesh double-bumper concept shows a 30 to 40 percent weight reduction compared to an aluminum Whipple shield in the velocity range study, besides such advantages as an increased resistance to penetration and the fact that the aluminum mesh does not produce damaging secondary ejecta particles. It is suggested that the ballistic protection can be improved even more if an intermediate layer of a high-strength cloth is attached near the rear wall.

Christiansen, Eric L.↗