Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STAINLESS STEELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Friction surfacing and cold spray deposition for surface crack repair in austenitic stainless steels

Two technologies, friction surfacing (FS) and cold spray deposition (CSD), have been investigated for field repair of cracks in 304L austenitic stainless steel. Both technologies are low-heat-input, solid-state technologies that do not introduce the detrimental effects of solidification, such as compositionally segregated microstructures and shrinkage stresses. Friction surfacing was performed using a 304L stainless steel rod over the substrate of the same material. Further, the process was performed at a high spindle speed of 20,000 RPM allowing for process forces below 500N to be used effectively. Spherical gas-atomized 304L stainless steel powder, in size range of 25–44 µm, was used as feedstock powder for the cold spray process for deposition on 304L substrates. Both technologies showed leak-tight crack repair capabilities on ~30–50 µm wide simulated through-crack specimens based on helium leak tests.

36 MATERIALS SCIENCE↗

Strength and ductility of additively manufactured 316L stainless steel: Impact of neutron irradiation and data variability

Here, this article presents the mechanical properties of additively manufactured (AM) 316L stainless steel processed via the laser powder bed fusion (LPBF) method, focusing on the effects of neutron irradiation on mechanical properties and the variability in strength and ductility data. The rapid melting-solidification process and multiple heating-cooling cycles inherent in LPBF typically result in a fine, metastable microstructure with significant local variability. AM 316L builds of varying thicknesses were fabricated, and SS-J3 miniature tensile specimens were machined from six different locations. These specimens were irradiated with fast neutrons to doses of 2 and 10 dpa at target temperatures of 300 °C and 600 °C. Post-irradiation tensile tests were conducted at room temperature, 300 °C, and 600 °C. Compared to conventional 316L stainless steel, AM 316L exhibited higher initial strength but lower ductility. Irradiation at 300 °C caused significant hardening and prompt necking at yield, with limited uniform ductility, although embrittlement was not observed up to 10 dpa. While neutron irradiation, particularly at 600 °C, increased the variability in strength and ductility data, no clear dependence of mechanical properties on build thickness or sampling location was found—contrary to the conventional perception that AM materials may exhibit high property variability. Furthermore, we observed that the variability in property data for LPBF-processed 316L was relatively low compared to that of wrought 316L stainless steel. This reduced variability in AM 316L steel may be attributed to its highly metastable, stress-containing microstructure, which is discussed in the context of general tensile property variations.

Additively manufactured 316L stainless steel↗

Evaluation of Pad 18 Spent Mercury Gold Trap Stainless Steel Container Failure

Failure of the Pad 18 spent mercury gold trap stainless steel waste container is principally attributed to corrosion induced by degradation of plasticized polyvinyl chloride (pPVC) waste packaging material. Dehydrochlorination of pPVC polymer by thermal and/or radiolytic degradation is well-known to evolve HCl gas, which is highly corrosive to stainless steel and other metals in the presence of moisture. Degradation of the pPVC packaging material was likely caused by radiolysis in the presence of tritium gas within the waste container, though other degradation mechanisms (aging, thermo-oxidation, plasticizer migration) over 30 years storage may have contributed. Corrosion was also likely enhanced by the crevice in the container weld design, and may have been enhanced by the presence of tritiated water. Similar non-failed spent mercury gold trap waste containers did not show radiographic evidence of plastic packaging or trapped free liquid within the container. Therefore, those containers are not expected to exhibit similar failures. Halogenated polymers such as pPVC subject to degradation can evolve halide gases such as HCl, which is corrosive in the presence of moisture and can generate pressure in sealed systems.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Meshfree simulation and prediction of recrystallized grain size in friction stir processed 316L stainless steel

Friction stir processing (FSP) is a promising solid-phase microstructural modification technique that can repair and enhance damaged stainless steel surfaces exposed to harsh environments. The quality of the repaired material is closely correlated to the recrystallized grain size in the stir zone (SZ), which is influenced by the thermomechanical conditions dictated by FSP process parameters. Thus, establishing a reliable relationship between these parameters and recrystallized grain size in the SZ is crucial for optimizing repair quality. However, existing experimental approaches often rely on indirect temperatures measured far from the SZ, along with rough strain rate estimations, which are imprecise and time-consuming. Meanwhile, existing mesh-based modeling methods usually face numerical challenges when dealing with the large material deformations inherent in FSP. Here, to address these issues, this study introduces a meshfree process model for FSP based on the smoothed particle hydrodynamics (SPH) method, aimed at predicting process conditions under different parameters. The model is validated using experimental data from 11 combinations of tool traverse and rotation speeds on 316 L stainless steel. Correlations between process parameters, material flow, temperature, strain, strain rate, and recrystallized grain size are revealed through SPH simulations and electron backscatter diffraction (EBSD) imaging. The results show that in situ SZ temperatures range from 1071 to 1322°C, which exceed the tool temperature by over 300°C. Furthermore, SZ temperature, strain rate, and grain size increase monotonically with higher tool temperature and faster traverse speed. A relationship is then established between the model-predicted Zener-Hollomon parameter and the recrystallized grain size based on EBSD data, expressed as ln(d) = -0.364 ln(Z) + 14.673. Finally, this relationship exhibits satisfactory accuracy with errors of less than 26.9% in predicting grain sizes at various SZ locations, which offers valuable insights for optimizing FSP repair processes for 316 L stainless steel.

316L stainless steel↗

Alloying of Pu-Al with Stainless Steel for Material Disposition

The Savannah River National Laboratory (SRNL) has evaluated several options for the disposition of stainless-steel clad plutonium metal alloy. One of the technologies under consideration is alloying of the material with stainless steel (SS). The resulting SS-Pu alloy would be a non-proliferable waste form consisting of a secondary Pu composition region microencapsulated in the refractory stainless steel. Two 8-kg ingots were made at SS-1.8Zr-0.4Pu alloys (wt %); 8 kg was determined in a previous study to be the maximum mass of SS ingot at the maximum target Pu loading of 350-g that would result in a SS-4.4Pu alloy (wt %). Two smaller 500-g ingots were also produced at SS-1.6Zr-1.4Pu and SS-1.4Pu (wt %). The 500-g ingots evaluated alloying at a higher Pu concentration than in the 8 kg ingots, and they evaluated the necessity of adding Zr metal to incorporate the Pu and control Pu oxidation. Zr addition was found to be unnecessary to incorporate the Pu and control Pu oxidation. Drill turnings were collected from the large and small ingots and metallographic samples were directly cut from the small ingots. Both were analyzed to validate the structure and composition region formation. Chemical analyses of turnings proved that the Pu was dispersed within the SS ingots.

36 MATERIALS SCIENCE↗

Friction Drilling of Stainless Steels Pipes

This work describes the experimental study of the friction drilling process in stainless steel by means of an optimization of the machining conditions. For such purpose austenitic stainless steel with different thicknesses were analyzed through controlled tests at different rotation speeds and feed rates. On one hand, the torque and the thrust force were computed and monitorized. On the other hand, the dimensional tolerances of the holes were evaluated, mainly the accuracy of the hole diameter and the burr thickness at different depths. Another topic of interest inherent to this special technique is the temperature level reached during the friction process which is crucial when it comes to development of microstructural transformations.

36 MATERIALS SCIENCE↗

Effect of ageing on precipitation and impact energy of 2101 economical duplex stainless steel

The impact energy and microstructure of a thermally aged 2101 duplex stainless steel with composition of Fe-21.4Cr-1.2Ni-5.7Mn-0.23 N-0.31Mo were studied. The results showed that the room temperature impact energy of specimens decreased gradually with ageing temperature up to 700 deg. C and then increased with aging over 700 deg. C. The minimum value of impact energy was 37 J after 700 deg. C aging, which was only 34% of that for as-annealed specimens. For specimens aged at 700 deg. C, the room temperature impact energy decreased significantly after 3 min and was halved after 10 min. Fractographs showed that, with increasing aging time, the fracture morphology changed from fibrous fracture to transgranular and intragranular fracture. Scanning electron micrographs revealed that many precipitates were distributed along {alpha}/{gamma} and {alpha}/{alpha} interfaces. The precipitates were extracted and confirmed by X-ray diffraction to be Cr{sub 2}N. Therefore, it can be concluded that precipitation of Cr{sub 2}N is the main reason for the decrease of impact energy in aged 2101 duplex stainless steel.

36 MATERIALS SCIENCE↗

Mechanical Response of Additively Manufactured Stainless Steel 304L Across a Wide Range of Loading Conditions

The mechanical response of additively manufactured (AM) stainless steel 304L has been investigated across a broad range of loading conditions, covering 11 decades of strain rate, and compared with the behaviors of traditional ingot-derived (wrought) material. In general, the AM material exhibits a greater strength and reduced ductility compared with the baseline wrought form. These differences are consistently found from quasi-static and high strain rate tests. A detailed investigation of the microstructure, the defect structure, the phase, and the composition of both forms reveals differences that may contribute to the differing mechanical behaviors. Compared with the baseline wrought material, dense AM stainless steel 304L has a more complex grain structure with substantial sub-structure, a fine dispersion of ferrite, increased dislocation density, oxide dispersions and larger amounts of nitrogen. In-situ neutron diffraction studies conducted during quasi-static loading suggest that the increased strength of AM material is due to its initially greater dislocation density. The flow strength of both forms is correlated with dislocation density through a square root dependence akin to a Taylor-like relationship. Neutron diffraction measurements of lattice strains also correlate with a crystal plasticity finite element simulations of the tensile test. Other simulations predict a significant degree of elastic and plastic anisotropy due to crystallographic texture. Hopkinson tests at higher strain rates $\dot{ε}$ = 500 and 2500 s -1 ) also show a greater strength for AM stainless steel 304L; although, the differences compared with wrought are reduced at higher strain rates. Gas gun impact tests, including reverse ballistic, forward ballistic and spall tests, consistently reveal a larger dynamic strength in the AM material. The Hugoniot Elastic Limit (HEL) of AM SS 304L exceeds that of wrought material although considerable variability is observed with the AM material. Forward ballistic testing demonstrates spall strengths of AM material (3.27 -- 3.91 GPa) that exceed that of the wrought material (2.63 -- 2.88 GPa). The Hugoniot equation-of-state for AM samples matches archived data for this metal alloy.

36 MATERIALS SCIENCE↗

Influence of crystallographic orientation and applied magnetic field on domain structure in duplex stainless steel studied using magnetic force microscopy

Highlights: • Ferrite phase in a duplex stainless steel consists of stripe type domains. • Domain contrast decreases with deviation of plane normal from <100>. • Domain width increases with deviation of plane normal from <100>. • Domain alignment with applied field observed along <100> directions. • Grain boundary stray field is a function of misorientation between grains. - Abstract: The paper investigates the local micro-magnetization behavior in duplex stainless steel (DSS) using magnetic force microscopy (MFM). DSS has equal amount of austenite phase in ferrite matrix. The MFM imaging clearly differentiates ferrite phase (ferromagnetic) from the austenite phase (paramagnetic) due to the maze type magnetic domains present in the ferrite phase. The magneto crystalline anisotropic effect on the domain structure is discussed with the support of electron backscatter diffraction (EBSD) measurements. The MFM phase contrast and domain width are correlated with the orientation of surface normal with respect to the easy axis of magnetization (<100>). The influence of external magnetic field (±127 kA/m) application on the domain structure is studied as a function of the grain orientation and the leakage field at the grain boundaries is analyzed based on the mis-orientation between the grains.

36 MATERIALS SCIENCE↗

Precipitate Evolution in Low-Nickel Austenitic Stainless Steels During Neutron Irradiation at Very Low Dose Rates

Neutron-induced microstructural evolution in response to long term irradiation at very low dose rates was studied for a Russian low-nickel austenitic stainless steel designated Х18Н9 that is analogous to AISI 304. The irradiated samples were obtained from an out-of-core support column for the pressure vessel of the BN-600 fast reactor with doses ranging from 1.7 to 20.5 dpa generated at 3.8x10-9 to 4.3x10-8 dpa/s. The irradiation temperatures were in a very narrow range of 370-375°С. Microstructural observation showed that in addition to voids and dislocations, an unexpectedly high density of small G-phase precipitates was formed that are not usually observed at higher dpa rates in this temperature range. A similar behavior was observed in a Western stainless steel, namely AISI 304 stainless steel, irradiated at similar temperatures and somewhat higher dpa rates in the EBR-II fast reactor, indicating that irradiation at low dpa rates for many years can lead to a different precipitate microstructure and therefore different associated changes in matrix composition than are generated at higher dpa rates. The contribution of such radiation-induced precipitation to changes in electrical resistivity was measured in the Х18Н9 specimens and was shown to cause significant deviation from predictions based only on void swelling.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Investigations of Localized Corrosion of Stainless Steel after Exposure to Supercritical CO2

Severe localized corrosion of a 316 stainless steel autoclave occurred during investigating Type H Portland cement stability in 0.16 M CaCl{sub 2} + 0.02 M MgCl{sub 2} + 0.82 M NaCl brine in contact with supercritical CO{sub 2} containing 4% O{sub 2}. The system operated at 85 C and pressure of 29 MPa. However, no corrosion was observed in the same type of autoclave being exposed to the same environment, containing Type H Portland cement cylindrical samples, also operating at pressure of 29 MPa but at 50 C. The operation time for the 85 C autoclave was 53 days (1272 hours) while that for the 50 C autoclave was 66 days (1584 hours). Debris were collected from the base of both autoclaves and analyzed by X-ray diffraction (XRD). Corrosion products were only found in the debris from the 85 C autoclave. The cement samples were analyzed before and after the exposure by X-ray florescence (XRF) methods. Optical microscopy was used to estimate an extent of the 316 stainless steel corrosion degradation.

36 MATERIALS SCIENCE↗

Overview of strategies for high-temperature creep and oxidation resistance of alumina-forming austenitic stainless steels

A family of creep-resistant, alumina-forming austenitic (AFA) stainless steel alloys is under development for structural use in fossil energy conversion and combustion system applications. The AFA alloys developed to date exhibit comparable creep-rupture lives to state-of-the-art advanced austenitic alloys, and superior oxidation resistance in the {approx}923 K to 1173 K (650 C to 900 C) temperature range due to the formation of a protective Al{sub 2}O{sub 3} scale rather than the Cr{sub 2}O{sub 3} scales that form on conventional stainless steel alloys. This article overviews the alloy design approaches used to obtain high-temperature creep strength in AFA alloys via considerations of phase equilibrium from thermodynamic calculations as well as microstructure characterization. Strengthening precipitates under evaluation include MC-type carbides or intermetallic phases such as NiAl-B2, Fe{sub 2}(Mo,Nb)-Laves, Ni{sub 3}Al-L1{sub 2}, etc. in the austenitic single-phase matrix. Creep, tensile, and oxidation properties of the AFA alloys are discussed relative to compositional and microstructural factors.

36 MATERIALS SCIENCE↗

Evaluation of thermal processing and properties of 422 martensitic stainless steel for replacement of 4140 steel in diesel engine pistons

The thermal and mechanical properties of martensitic stainless steel 422 were evaluated for suitability as a drop-in replacement for 4140 steel in next generation heavy-duty diesel engine (HDDE) pistons. The time and temperature of the austenitization and tempering steps were studied to achieve optimum materials performance in piston applications, including the balance of thermal and mechanical properties and resistance to long-term thermal aging. Reducing the tempering temperature from 700 to 600 °C caused a substantial increase in elevated temperature strength from 25 to 600 °C, but had no significant influence on thermal conductivity, suggesting that thermal conductivity in 422 is dominated largely by composition and distribution of alloying elements and mostly independent of the sub-grain structure size and precipitate size. Compared to the current HDDE piston alloy 4140, 422 exhibits substantially higher elevated temperature strength and lower thermal conductivity, the latter which will cause 422 to operate at higher temperatures in pistons, possibly requiring a piston redesign to take advantage of the improved high temperature strength of 422. Piston material selection and alloy design strategies with potential to mitigate some of the shortcomings of martensitic stainless steels, such as 422, as drop-in replacements are discussed.

36 MATERIALS SCIENCE↗

A Stainless-Steel Mandrel for Slumping Glass X-Ray Mirrors

We have fabricated a precision full -cylinder stainless-steel mandrel at Marshall Space Flight Center. The mandrel is figured for a 30-cm-diameter primary (paraboloid) mirror of an 840-cm focal-lengthWolter-1 telescope. We have developed this mandrel for experiments in slumping.thermal forming at about 600 C-of glass mirror segments at Goddard Space Flight Center, in support of NASA fs participation in the International X -ray Observatory (IXO). Precision turning of stainless ]steel mandrels may offer a lowcost alternative to conventional figuring of fused -silica or other glassy forming mandrels. We report on the fabrication, metrology, and performance of this first mandrel; then we discuss plans and goals for stainless-steel mandrel technology.

ODell, Stephen L.↗

Development of Fiber Laser Weld Parameters for Stainless Steel and Refractory Metals

Laser welds were made in 21-6-9 stainless steel, vanadium and tantalum using LLNL's new 6kW fiber laser to target 1 mm penetration depths. The materials were machined into flat coupon samples with standard step-joint geometries, and were welded in a continuous wave mode. The laser was characterized using the Primes laser beam diagnostic system so that the beams can be reproduced in the future. The optical configuration consisted of a 200 {micro}m fiber, 200 mm collimator and 250 mm focusing lens, which delivered electron-beam level power densities in the 5 to 20 kW/mm2 range. The three different materials required different power densities to produce the desired penetration, and this report summarizes the results of this screening study that was directed at developing a first approximation to the proper welding parameters for future work. The results show that 1 mm penetrations can be achieved using a 400W beam for 21-6-9 stainless steel, a 600W beam for vanadium, and a 1,100W beam for tantalum using sharp focus and a travel speed of 40 inch/min. Future welds should incorporate a trailing gas shield to prevent discoloration of the surface and to prevent oxygen and nitrogen pickup in the welds.

36 MATERIALS SCIENCE↗

Material report in support to RCC-MRX code 2010 stainless steel parts and products

This paper presents the Material Report dedicated to stainless steels parts and products issued by AFCEN (Association Francaise pour les regles de Conception et de Construction des Materiels des Chaudieres Electro-Nucleaires) in support to RCC-MRx 2010 Code. The RCC-MRx Code is the result of the merger of the RCC-MX 2008, developed in the context of the research reactor Jules Horowitz Reactor project, in the RCC-MR 2007, which set up rules applicable to the design of components operating at high temperature and to the Vacuum Vessel of ITER (a presentation of RCC-MRx 2010 Code is the subject of another paper proposed in this Congress; it explains in particular the status of this Code). This Material Report is part of a set of Criteria of RCC-MRx (this set of Criteria is under construction). The Criteria aim at explaining the design and construction rules of the Code. They cover analyses rules as well as part procurement, welding, methods of tests and examination and fabrication rules. The Material Report particularly provides justifications and explanations on requirements and features dealing with parts and products proposed in the Code. The Material Report contains the following information: Introduction of the grade(s): codes and standards and Reference Procurement Specifications covering parts and products, applications and experience gained, - Physical properties, - Mechanical properties used for design calculations (base metal and welds): basic mechanical properties, creep mechanical properties, irradiated mechanical properties, - Fabrication: experience gained, metallurgy, - Welding: weldability, experience gained during welding and repair procedure qualifications, - Non-destructive examination, - In-service behaviour. In the article, examples of data supplied in the Material Report dedicated to stainless steels will be exposed. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Evaluation of Alternate Stainless Steel Surface Treatments for Mass Spectroscopy and Other Tritium Systems

There are specific components in the SRS Tritium Facilities that are required to introduce as few chemical impurities (such as protium and methane) as possible into the process gas. Two such components are the inlet systems for the mass spectroscopy facilities and hydrogen isotope mix standard containers. Two vendors now passivate stainless steel components for these systems, and both are relatively small businesses whose future viability can be questioned, which creates the need for new sources. Stainless steel containers were designed to evaluate alternate surface treatment vendors for tritium storage and handling for these high purity tritium systems. Five vendors applied their own 'best' surface treatments to two containers each - one was a current vendor, another was a chemical vapor deposited silicon coating, and the other three were electropolishing and chemical cleaning vendors. Pure tritium gas was introduced into all ten containers and the composition was monitored over time. The only observed impurities in the gas were some HT, less CT 4 , and very small amounts of T 2 O in all cases. The currently used vendor treated containers contained the least impurities. The chemical vapor deposited silicon treatment resulted in the highest impurity levels. Sampling one set of containers after about one month of tritium exposure revealed the impurity level to be nearly the same as that after more than a year of exposure - this result suggests that cleaning new stainless steel components by tritium gas contact for about a month may be a worthy operation.

03 NATURAL GAS↗

Microstructural characteristics and corrosion behavior of a super duplex stainless steel casting

The machining of super duplex stainless steel castings is usually complicated by the difficulty involved in maintaining the dimensional tolerances required for given applications. Internal stresses originating from the solidification process and from subsequent heat treatments reach levels that exceed the material's yield strength, promoting plastic strain. Stress relief heat treatments at 520 deg. C for 2 h are an interesting option to solve this problem, but because these materials present a thermodynamically metastable condition, a few precautions should be taken. The main objective of this work was to demonstrate that, after solution annealing at 1130 deg. C and water quenching, stress relief at 520 deg. C for 2 h did not alter the duplex microstructure or impair the pitting corrosion resistance of ASTM A890/A890M Grade 6A steel. This finding was confirmed by microstructural characterization techniques, including light optical and scanning electron microscopy, and X-ray diffraction. Corrosion potential measurements in synthetic sea water containing 20,000 ppm of chloride ions were also conducted at three temperatures: 5 deg. C, 25 deg. C and 60 deg. C.

36 MATERIALS SCIENCE↗