Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SOLVENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Levelized Cost of CO 2 Captured Using Five Physical Solvents in Pre-combustion Applications

Aspen Plus v8.8 was used to perform techno-economic analysis (TEA) of a CO 2 capture process from a typical fuel gas stream in a 543-MW pre-combustion power plant using five different physical solvents (Selexol, PEGPDMS-1, NMP, [aPy][Tf 2 N] and [hmim][Tf 2 N]). The process included a countercurrent packed-bed absorber operating under high-pressure over a wide range of temperatures and three pressure-swing flash drums for solvent regeneration. Furthermore, two packings, Mellapak 250Y and IMTP50, were used and the Levelized costs of CO 2 captured (LCOC) were calculated. The simulation results indicated that using Mellapak 250Y exhibited lower LCOC values than those when using IMTP50 for the five solvents under all conditions used as it offered better mass transfer. The CO 2 capture process carried out at low temperatures showed lower LCOC values than those at higher temperatures due to the increased CO 2 solubility in the solvents at lower temperatures, requiring smaller absorber diameter and lower solvent circulation rates, which offset the cooling requirements. Comparing the lowest LCOC values for the five solvents, the hydrophobic PEGPDMS-1 solvent was the most promising one compared to the other four solvents, due to its lowest capital and operating costs and noncorrosive, which enabled using less expensive materials for the process equipment.

42 ENGINEERING↗

Physicochemical and catalytic properties of Au nanorods micro-assembled in solvents of varying dipole moment and refractive index

Highlights: • Physicochemical activities of Au nanorods in water largely differ from organic solvents. • Au nanorods agglomeration increased with dipole moments of different polar solvents. • Refractive indexes of Au nanorods dispersion in various polar solvents are enhanced. • Electrokinetics significantly altered depending on agglomerated size of Au nanorods. • Catalysis or co-catalysis activity is varied as per the extent of Au nanorods coagulation. - Abstract: This paper deals with the impact of dipole moment (1.66–3.96 D) and refractive index (1.333–1.422) of the dispersion solvent on the plasmon absorption, surface charge, zeta potential, and adsorption properties of Au nanorods (AuNRs). AuNRs (length ≈ 53 nm and width ≈ 20 nm) undergo agglomeration (size 50–180 nm) with increase in the dipole moment of solvent (iPrOH < MeOH < DMF < DMSO). Whereas, no such coagulation occurs in H{sub 2}O and CCl{sub 4} suspension as confirmed by DLS and TEM size distribution. The electrostatic interaction of AuNRs with its surface adsorbed solvent dipoles leads to alteration of the their ionic state, absolute electronic charge and zeta potential (+49.79 mV in H{sub 2}O, +8.99 mV in DMF and −4.65 mV in MeOH dispersion) to a greater extent. This interaction distinctly modifies the adsorption behavior of polar molecules like p-nitrophenol and salicylic acid on AuNRs surface, as evidenced by the measured changes in their electro-kinetic parameters. As a result, we observe a substantial difference in catalytic and co-catalytic activities of AuNRs dispersed in various solvents as mentioned above because the catalytic properties of AuNRs are strongly dependent on the type of solvent in which they are dispersed.

36 MATERIALS SCIENCE↗

Extraction of valuable chemicals from food waste via computational solvent screening and experiments

About 1.3 billion tons of global food production end up in landfills and composting, leading to significant anthropogenic greenhouse gas (GHG) emissions. Extracting antioxidant and antimicrobial chemicals (flavonoids, phenolic acids, etc.) from food waste is an economically lucrative valorization strategy but is hindered by efficient solvent selection. Here we perform in silico high throughput screening to identify high solubility solvents for key phenolics and reveal more than 100+ higher-performing solvents than the traditional ethanol and methanol. Solubilities of nine shortlisted solvents are measured and found in reasonable agreement with model predictions. Analysis of the Conductor like Screening Model for Real Solvents (COSMO-RS) σ-profiles and Hansen Solubility Parameters reveals that polarity and hydrogen bonding make dimethylformamide (DMF) an excellent single solvent. We showcase the replacement of high-solubility toxic solvents with green mixtures and demonstrate the approach to potato peel waste. As a result, our work provides a blueprint for solvent selection and generates new insights into extraction from food waste.

09 BIOMASS FUELS↗

Green solvent-processable poly(3-hexylthiophene) derivative maintains high hole mobility in diodes

The development of environmentally sustainable fabrication methods for organic solar cells (OSCs) is critical to enable their large-scale adoption. Conventional solution-processed OSCs often rely on halogenated, toxic solvents that pose health and environmental risks, limiting their scalability. This is because π-conjugated polymers tend to have a low solubility in non-halogenated solvents. A common strategy to enhance solubility in alternative solvents is through the incorporation of polar solubilizing groups, often on every repeat unit of at least one monomer. However, too many polar side chains tend to disrupt favorable morphology and decrease charge transport properties. In this study, we demonstrate that a minimal degree of side chain functionalization can improve green solvent processability while preserving electrical performance. We tested this hypothesis using our previously reported random copolymer derivative of poly(3-hexylthiophene) (P3HT) where ∼10 mol% of the side chains are 6-pentanoatehexyl side chains. We find that this low-level functionalization significantly broadens the solvents that can be used to process P3HT to less toxic solvents such as o-xylene and anisole. Furthermore, the copolymer processed from greener solvents showed high hole mobilities (∼10⁻ 3 cm 2 /Vs by the Space-Charge Limiting Current method in diodes), comparable to P3HT films cast from toxic chloroform. These findings suggest that minimal side-chain modification is a viable strategy for expanding green solvent compatibility while preserving electrical performance, paving the way toward more sustainable organic semiconductor designs.

36 MATERIALS SCIENCE↗

Solvent Transport in Disordered and Dynamic Membrane Pores: Implications for Reverse Osmosis and Nanofiltration Membranes

Pressure-driven separations with nanoporous membranes, such as reverse osmosis and nanofiltration, play a vital role in addressing water scarcity and enabling resource recovery. Understanding water or solvent transport in membrane pores is essential for advancing membrane separation technologies. A key question in transport modeling is to establish a relationship between solvent permeability and membrane porous structure properties, such as porosity or pore size. The nano- and subnanometer pores in polymeric membranes such as reverse osmosis and nanofiltration membranes are highly tortuous and dynamically connected, which challenges the conventional methods of transport modeling. This study addresses this challenge by developing a theoretical framework to describe solvent transport through membranes with dynamic and disordered porous structure. Specifically, we propose a lattice model to describe the pore network, while preserving the viscous nature of solvent permeation. We further establish a relationship between solvent permeability and membrane porosity or pore size, which is validated by molecular dynamics simulations and experimental data. By integrating this relationship into the solution-friction model, we define pore connectivity and local friction coefficient to quantify the impact of pore structure on solvent permeability. Our analysis highlights the dominant influence of pore connectivity on the permeability of reverse osmosis and nanofiltration membranes, particularly when the pore size approaches the dimensions of solvent molecules. Overall, this study provides critical insights into water and solvent transport mechanisms in nanoporous membranes, opening the door for strategies to substantially enhance membrane performance.

membranes↗

Machine Learning-Driven Solvent Screening for Biobased 2,3-Butanediol Extraction

Biobased 2,3-butanediol (2,3-BDO) is a valuable biomass-derived chemical due to its versatility in being transformed into a wide variety of products. However, the separation and purification of 2,3-BDO from fermentation broth remain a significant challenge owing to its high boiling point and hydrophilic nature. Herein, we developed a machine learning (ML)-based screening workflow that uses molecular calculations as training data and requires only a small number of experimental measurements for validation to identify alternative solvent candidates for the liquid–liquid extraction (LLE) of 2,3-BDO from aqueous solution. In particular, 130 density functional theory (DFT) calculations with the implicit solvation method not only built a correlation between the computational partition coefficient and the experimental distribution coefficient of 2,3-BDO but also parameterized an Extra-Trees ML model to screen the distribution coefficient for a wider range of 6717 organic solvents. The experimental measurements of only 24 solvents were needed to validate the computational results. A list of 50 prioritized solvents was proposed for 2,3-BDO LLE, and seven additional experimental measurements were conducted to further verify our selected solvents. The impact of the extraction temperature and solvent-to-feed ratio was also investigated for selected solvents in experiments. Furthermore, this work suggested alternative solvents for 2,3-BDO LLE and proposed a versatile workflow that requires fewer experiments and can be applied to a broader range of LLE studies.

Extraction↗

Effect of Solvents on Lignin–Surface Interactions via Molecular Dynamics Simulations

Lignin, an essential building block of lignocellulosic biomass, is a potential abundant source of aromatic monomers for the polymer and chemical industry. Reductive catalytic fractionation (RCF) is one promising process that can produce high yields of phenolic monomers and oligomers from lignin under different catalytic conditions. An important choice in optimizing RCF is the selection of solvent; however, detailed insights into solvent effects on lignin behaviors and interactions remain limited. Here, in this work, we perform all-atom molecular dynamics simulations to study the solvation of lignin, solvent-mediated conformational changes, and the interaction of solvated lignin oligomers with model surfaces. We focus on the behavior of an oligomeric lignin model compound in methanol, ethanol, a binary mixture of ethanol and water, and water at both the RCF reaction temperature (473 K) and room temperature. Analysis of structural features of lignin suggests that these three organic solvent systems favorably solvate lignin, resulting in a more extended conformation suitable for catalytic conversion to valuable chemicals. We further introduce model palladium (Pd) and carbon (C) surfaces to understand how solvent choice impacts adsorption onto a representative catalytic surface and support, and to quantify the competition among the reactant and solvent molecules for the surface. Unbiased simulations suggest strong adsorption of lignin on both Pd and C surfaces at 473 K, with notable solvent-mediated differences in adsorption energies. Additionally, our findings indicate that lignin adsorption is promoted by the entropy change resulting from the displacement of solvent molecules from the surface. This study provides a molecular perspective of adsorption of lignin onto varying surfaces, which is a step towards understanding and optimizing the catalytic conversion of lignin into valuable chemicals.

adsorption↗

Revealing the Effects of the Non-solvent on the Ligand Shell of Nanoparticles and Their Crystallization

When nanoparticles (NPs) are assembled from solution, a common assembly method of choice is either solution destabilization or solvent evaporation technique. The destabilization of the NP solution by non-solvents results in the formation of faceted supercrystals (SCs) while periodic film-like assemblies are typically formed by solvent evaporation. In this article, we reveal the effect of non-solvents in washing, dispersing, and crystallizing NPs. Small angle neutron scattering (SANS) is employed for monitoring the ligand shell of NPs in solutions upon introduction of various non-solvents. The SC crystallization process is traced in situ with small-angle X-ray scattering (SAXS), and the structures of the resulting single-crystalline SCs are examined in detail by mapping the reciprocal space using SAXS and wide-angle X-ray scattering. Our study suggests that the relative miscibility of the non-solvent with solvents and ligands 4111 determines the solvation and thickness of the ligand shell and thereby the resulting structure of SCs. In the early stage of crystallization, truncated octahedral PbS NPs form SCs with face-centered cubic (fcc) symmetry. In the later stage, the fcc symmetry is preserved in the SC formed by larger (5.60 nm) NPs, but the SC assembled from smaller (4.14 nm) NPs undergoes a phase transition into body-centered cubic (bcc) lattice via Bain transformation, becoming a polycrystalline SC containing three structurally correlated bcc domains and one untransformed fcc domain. Our study provides the detailed understanding of the non-solvent effect that impacts beyond the formation of SCs, enabling the judicious selection of solvent/non-solvent mixtures for NP purification.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Solvent dependent structural perturbations of chemical reaction intermediates visualized by time-resolved x-ray diffraction

Ultrafast time-resolved wide angle x-ray scattering from chemical reactions in solution has recently emerged as a powerful technique for determining the structural dynamics of transient photochemical species. Here we examine the structural evolution of photoexcited CH{sub 2}I{sub 2} in the nonpolar solvent cyclohexane and draw comparisons with a similar study in the polar solvent methanol. As with earlier spectroscopic studies, our data confirm a common initial reaction pathway in both solvents. After photoexcitation, CH{sub 2}I{sub 2} dissociates to form CH{sub 2}I{center_dot}+I{center_dot}. Iodine radicals remaining within the solvent cage recombine with a nascent CH{sub 2}I{center_dot} radical to form the transient isomer CH{sub 2}I-I, whereas those which escape the solvent cage ultimately combine to form I{sub 2} in cyclohexane. Moreover, the transient isomer has a lifetime approximately 30 times longer in the nonpolar solvent. Of greater chemical significance is the property of time-resolved wide angle x-ray diffraction to accurately determine the structure of the of CH{sub 2}I-I reaction intermediate. Thus we observe that the transient iodine-iodine bond is 0.07 A {+-}0.04 A shorter in cyclohexane than in methanol. A longer iodine-iodine bond length for the intermediate arises in methanol due to favorable H-bond interaction with the polar solvent. These findings establish that time-resolved x-ray diffraction has sufficient sensitivity to enable solvent dependent structural perturbations of transient chemical species to be accurately resolved.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Molecular near-field antenna effect in resonance hyper-Raman scattering: Intermolecular vibronic intensity borrowing of solvent from solute through dipole-dipole and dipole-quadrupole interactions

We quantitatively interpret the recently discovered intriguing phenomenon related to resonance Hyper-Raman (HR) scattering. In resonance HR spectra of all-trans-β-carotene (β-carotene) in solution, vibrations of proximate solvent molecules are observed concomitantly with the solute β-carotene HR bands. It has been shown that these solvent bands are subject to marked intensity enhancements by more than 5 orders of magnitude under the presence of β-carotene. We have called this phenomenon the molecular-near field effect. Resonance HR spectra of β-carotene in benzene, deuterated benzene, cyclohexane, and deuterated cyclohexane have been measured precisely for a quantitative analysis of this effect. The assignments of the observed peaks are made by referring to the infrared, Raman, and HR spectra of neat solvents. It has been revealed that infrared active and some Raman active vibrations are active in the HR molecular near-field effect. The observed spectra in the form of difference spectra (between benzene/deuterated benzene and cyclohexane/deuterated cyclohexane) are quantitatively analyzed on the basis of the extended vibronic theory of resonance HR scattering. The theory incorporates the coupling of excited electronic states of β-carotene with the vibrations of a proximate solvent molecule through solute–solvent dipole–dipole and dipole–quadrupole interactions. It is shown that the infrared active modes arise from the dipole–dipole interaction, whereas Raman active modes from the dipole–quadrupole interaction. It is also shown that vibrations that give strongly polarized Raman bands are weak in the HR molecular near-field effect. The observed solvent HR spectra are simulated with the help of quantum chemical calculations for various orientations and distances of a solvent molecule with respect to the solute. The observed spectra are best simulated with random orientations of the solvent molecule at an intermolecular distance of 10 Å.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A smooth and differentiable bulk-solvent model for macromolecular diffraction

A new method for modeling the bulk solvent in macromolecular diffraction data based on Babinet’s principle is presented. The proposed models offer the advantage of differentiability with respect to atomic coordinates. Inclusion of low-resolution data in macromolecular crystallography requires a model for the bulk solvent. Previous methods have used a binary mask to accomplish this, which has proven to be very effective, but the mask is discontinuous at the solute–solvent boundary (i.e. the mask value jumps from zero to one) and is not differentiable with respect to atomic parameters. Here, two algorithms are introduced for computing bulk-solvent models using either a polynomial switch or a smoothly thresholded product of Gaussians, and both models are shown to be efficient and differentiable with respect to atomic coordinates. These alternative bulk-solvent models offer algorithmic improvements, while showing similar agreement of the model with the observed amplitudes relative to the binary model as monitored using R, R{sub free} and differences between experimental and model phases. As with the standard solvent models, the alternative models improve the agreement primarily with lower resolution (>6 Å) data versus no bulk solvent. The models are easily implemented into crystallographic software packages and can be used as a general method for bulk-solvent correction in macromolecular crystallography.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Mass Transfer And Hydraulic Testing Of The V-05 And V-10 Contactors With The Next Generation Solvent

The Modular Caustic Side Solvent Extraction (CSSX) Unit (MCU) facility is actively pursuing the transition from the current BOBCalixC6 based solvent to the Next Generation Solvent (NGS)-MCU solvent. To support this integration of NGS into the MCU facilities, Savannah River Remediation (SRR) requested that Savannah River National Laboratory (SRNL) perform testing of a blend of the NGS (MaxCalix based solvent) with the current solvent (BOBCalixC6 based solvent) for the removal of cesium (Cs) from the liquid salt waste stream. This testing differs from prior testing by utilizing a blend of BOBCalixC6 based solvent and the NGS with the full (0.05 M) concentration of the MaxCalix as well as a new suppressor, tris(3,7dimethyloctyl) guanidine. Single stage tests were conducted using the full size V-05 and V-10 centrifugal contactors installed at SRNL.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Solvent hold tank sample results for MCU-16-53-55. January 2016 Monthly sample

Savannah River National Laboratory (SRNL) received one set of Solvent Hold Tank (SHT) samples (MCU-16-53-54-55), pulled on 01/25/2016 for analysis. The samples were combined and analyzed for composition. Analysis of the composite sample MCU-16-53-54-55 indicated the Isopar™L, and MaxCalix are at nominal levels. The modifier and TiDG concentrations are 3% and 23 % below their nominal concentrations. This analysis confirms the addition of TiDG, MaxCalix, and modifier to the solvent on November 28, 2015. Based on the current monthly sample, the levels of TiDG, Isopar™L, MaxCalix, and modifier are sufficient for continuing operation but are expected to decrease with time. Periodic characterization and trimming additions to the solvent are recommended. No impurities above the 1000 ppm level were found in this solvent by the Semi-Volatile Organic Analysis (SVOA). No impurities were observed in the Hydrogen Nuclear Magnetic Resonance (HNMR). However, the Fourier transform infra-red spectroscopy (FTIR) method detected trace levels (a few ppm) of amides (a possible degradation product of TiDG). In addition, up to 21 ± 4 micrograms of mercury per gram of solvent (or 17.5 μg/mL) was detected in this sample. There appears to be a possible correlation between the mercury level and the TiDG concentration in the solvent. The current gamma level (9.16 E4 dpm/mL) confirmed that the gamma concentration has returned to previous level where the process operated normally and as expected. The laboratory will continue to monitor the quality of the solvent in particular for any new impurities or degradation of the solvent components.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Molecular Level Understanding of the Interactions Between Reaction Intermediates of Li–S Energy Storage Systems and Ether Solvents

The lithium–sulfur energy storage system has the potential to deliver high energy density for grid and transportation applications. Lithium polysulfides (LiPS) formed during the chemical transformation of elemental sulfur can be reactive toward commonly used ether solvents. In this chapter, using density functional theory calculations, we address kinetic and thermodynamic feasibilities of LiPS reactions with various ether molecules (linear and cyclic) and fluorine-substituted ether molecules to understand their long-term chemical stability as solvents or cosolvents. These a priori computations indicate that the most reactive intermediates that initiate a likely degradation reaction of ether solvent molecules are Li2S2, Li2S3, Li2S4, and S2 2−. The lowest computed activation barriers (ΔH ‡) for the CO bond cleavage of dimethoxy ethane (DME) by shorter chain polysulfides or sulfide anions are in the range of ∼27–35 kcal mol−1, suggesting extremely slow kinetics for a polysulfide-induced ether solvent degradation. Calculations are extended to nine more linear and cyclic ether solvent molecules including the glymes, tetrahydrofuran (THF), and dioxolane (DOL). Computations suggest that the solvent stability is higher for shorter chain linear ethers compared to longer chain linear ethers and cyclic ethers. In addition to the 10 ether solvent candidates, simulations were also performed to understand the kinetic stability of 16 fluorinated DME molecules – a model for fluorinated ether species. Computations show that the introduction of one or more CF bond(s) in linear ether molecules enables nucleophilic attack by the polysulfide species, especially toward the polar CF/CO bonds. The CO bond stability of the fluoroether molecule was also compromised by the presence of the highly electron-withdrawing “−F” functional group. In general, in this chapter, utilizing the predictive power of first principle simulations, the LiPS reactivity toward ether solvent molecules was simulated and likely reactions that cause degradation are discussed. These studies also provide guidelines for the design of electrolyte systems with longer term chemical stability.

Assary, Rajeev S.↗

An in situ GISAXS study of selective solvent vapor annealing in thin block copolymer films: Symmetry breaking of in‐plane sphere order upon deswelling

ABSTRACT Thin films of asymmetric poly(styrene‐ b ‐4‐vinylpyridine) (PS‐ b ‐P4VP) block copolymers are studied by means of in situ grazing‐incidence small‐angle X‐ray scattering (GISAXS) during solvent vapor annealing in tetrahydrofuran, a solvent selective for the PS majority block of the copolymer. Upon swelling, PS‐ b ‐P4VP block copolymers form hexagonal arrays of spherical P4VP microdomains in a PS matrix in films 7–9 layers thick. Deswelling the films induces a transition from hexagonal to face‐centered orthorhombic (fco) symmetry, which is stable only at ∼7 layers of spherical microdomains. Dry films show co‐existing hexagonal and orthorhombic symmetries when the solvent is removed slowly, whereas instantaneous solvent removal suppresses the fco structure, resulting in films with only hexagonal structure. The in‐plane order of microdomains is significantly deteriorated in dry films independent of the solvent removal rate.Spherical block copolymer microdomains are known to undergo a transition from hexagonal to orthorhombic packing in isothermally annealed thin films when the number of sphere layers is increased from 4 to 5. In this paper, in situ GISAXS experiments reveal that a similar transition occurs during solvent vapor annealing in a selective solvent. Interestingly, the transition from hexagonal to orthorhombic packing of spheres occurs as solvent is removed from a thin block copolymer film. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016, 54, 331–338

Gunkel, Ilja↗

Roles of Solvent in the Catalytic Hydrogen Release from Liquid Organic Hydrogen Carriers: Chemical, Thermodynamical and Technological Aspects

A Liquid Organic Hydrogen Carrier (LOHC) enables the storage and transport of hydrogen at ambient pressures and temperatures in a safe and convenient form using current infrastructure. However, it is challenging to directly compare reactivity and selectivity for hydrogen release, especially when comparing the catalytic efficiencies of neat LOHCs to highly diluted LOHCs in different solvents, reaction conditions, and catalysts. This work evaluates the role of solvents in catalysis and quantifies the energy efficiency of the overall process. The presence of solvent dilutes the volumetric density of available hydrogen, but may be necessary to achieve optimal catalysts stability, reactivity, and product selectivity. With respect to the reaction conditions as determined by thermodynamics, solvents with higher vapor pressures than that of the carrier can cause the erroneous impression of a more favorable reaction equilibrium. Concerning energy efficiency, solvents can result in increased energy demand for hydrogen release as the inert solvent must be heated to reaction temperatures required for release of H 2 from the LOHC. Further, this work recommends that investigations of catalyst reactivity should be carried out at different ratios of solvent to LOHC to understand how the reactivity changes and what the implications are for maximizing energy density and catalyst stability and reactivity. Investigations should also consider how these implications will affect the technical needs of applications intended for the LOHC system. Based on the results of this study, it is advised to focus research activities on LOHC systems with a gravimetric solvent content below about 50% as the thermodynamic disadvantages become very pronounced beyond this threshold.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Scalable Screening of Soft Matter: A Case Study of Mixtures of Ionic Liquids and Organic Solvents

Room-temperature ionic liquids (RTILs) are a class of organic salts that are liquid at room temperature. Their physiochemical properties, including low vapor pressure and wide electrochemical stability window, have expedited their use as electrolytes in many electrochemical applications; yet, the slow transport properties of many RTILs have limited their utility in some applications. This issue is often mitigated by solvating ionic liquids in neutral organic solvents. To date, however, solvent interactions have only been explored for a small number of solvents, particularly acetonitrile and propylene carbonate, at only a few compositions. Here, we use molecular dynamics simulations in the context of a computational screening approach to study mixtures of ionic liquids in many different solvents at a range of concentrations. Building on prior work, we again find that ionic liquid diffusivity increases monotonically with greater solvent concentration. In contrast to prior work, we find that pure solvent diffusivity, not polarity, is the most influential solvent property on mixture behavior. We also explore the concentration dependence of ionic conductivity and find maxima at intermediate concentrations. Experimental conductivity measurements, inspired by the computational screening study, support this observation with qualitatively consistent results. These results can further guide the selection of solvents for electrochemical applications of RTILs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Influence of Ether Solvent and Anion Coordination on Electrochemical Behavior in Calcium Battery Electrolytes

The emergence of magnesium and calcium batteries as potential beyond Li ion energy storage technologies has generated significant interest into the fundamental aspects of alkaline earth metal cation coordination in multivalent electrolytes and the impact of coordination on application-critical electrolyte properties such as solubility, transport, and electrochemical stability. Understanding these details in calcium electrolytes is of immediate importance due to recent, unprecedented demonstrations of reversible calcium metal electrodeposition in a limited number of ethereal solvent-based systems. In this work, we provide insight connecting Ca 2+ coordination tendencies to important calcium battery electrolyte properties. Our results demonstrate a clear solvent:Ca 2+ coordination strength trend across a series of cyclic ether and linear glyme solvents that controls the extent of ion association in solutions of “weakly” coordinating salts. We apply understanding gained from these results to rationalize relative anion:Ca 2+ coordination tendencies and attendant Ca 2+ coordination structures using two oxidatively stable anions of particular interest for current battery electrolytes. Armed with this understanding of solvent and anion interactions with Ca 2+ , we demonstrate and interpret differences in electrochemical calcium deposition behavior across several electrolyte exemplars with varying solvent and anion coordination strengths. Our findings demonstrate that solvents exhibiting especially strong coordination to Ca 2+ , such as triglyme, can inhibit reversible calcium deposition despite effective elimination of anion:Ca 2+ coordination while solvents exhibiting more modest coordination strength, such as 1,2-dimethoxyethane, may enable deposition provided anion:Ca 2+ coordination is substantially limited. These results reveal that the strength of coordination of both anion and solvent should be considered in the design of electrolytes for calcium batteries.

25 ENERGY STORAGE↗