Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SI”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Study of the ${{^{25}}}$Mg(d,p)${{^{26}}}$Mg reaction to constrain the ${{^{25}}}$Al(p,${\gamma }$)${{^{26}}}$Si resonant reaction rates in nova burning conditions

The rate of the 25 Al( p,γ) 26 Si reaction is one of the few key remaining nuclear uncertainties required for predicting the production of the cosmic γ-ray emitter 26 Al in explosive burning in novae. This reaction rate is dominated by three key resonances (J π = 0 + , 1 + and 3 + ) in 26 Si. Only the 3 + resonance strength has been directly constrained by experiment. A high resolution measurement of the 25 Mg(d, p) reaction was used to determine spectroscopic factors for analog states in the mirror nucleus, 26 Mg. A first spectroscopic factor value is reported for the 0 + state at 6.256 MeV, and a strict upper limit is set on the value for the 1 + state at 5.691 MeV, that is incompatible with an earlier ( 4 He, 3 He) study. These results are used to estimate proton partial widths, and resonance strengths of analog states in 26 Si contributing to the 25 Al( p,γ) 26 Si reaction rate in nova burning conditions.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2023

Electrochemical Formation of Li-M-(M')-Si Phases Using Multivalent Electrolyte Salt Additives

Lithium-rich silicides (Li 15 Si 4 ), formed during the electrochemical lithiation of silicon, show high reactivity with electrolyte components that contribute to capacity decay, formal lithium loss, and low coulombic efficiency. Recently, the reactivity of lithium silicides was found to be suppressed by substituting a multivalent cation (i.e. Mg, Ca) for lithium that results in the room temperature formation of a ternary Li-M-Si phase. In this study, we explored a range of multivalent electrolyte salt additives (M = Ni, Cu, La, Ce, Sr, Ba, and Ca-Mg mixed salt) in a lithium-ion cell configuration and identified a room temperature electrochemical route to the formation of new ternary and quaternary lithium silicides. Using this method, both nickel and copper salts were found to plate onto the silicon electrode surface upon lithiation. Further, based on refined synchrotron XRD data, multivalent cations with an ionic radius similar to Na (~1.03 Å) or smaller can be inserted electrochemically into a formally cation-deficient Li 15 Si 4 host lattice to form new ternary (or quartenary) phases. The electrochemical synthesis of a new quaternary Li-M-M’-Si phase represents a facile route to preparing and scaling materials isostructural to the Heusler phase and electron-precise Li 14 MgSi 4 phase that results in enhanced cycling and calendar life performance.

25 ENERGY STORAGE↗
DOE OSTI2020

Irradiation enhanced diffusion and diffusional creep in U₃Si₂

U₃Si₂ is a candidate as an advanced fuel for light water reactors (LWRs). Compared to UO₂, there are significant data gaps for the thermophysical and thermomechanical properties of U₃Si₂. Atomic scale simulations can help fill in those gaps, while also providing a more mechanistic understanding of the material properties. Creep is an important property for fuel performance as it influences the pellet-cladding gap, which in turn affects the temperature of the fuel (a key parameter in many other aspects of fuel behavior). In this work, we employed a DFT-informed cluster dynamics framework to predict point defect concentrations in U₃Si₂. The concentrations, diffusivities, and volumes of these defects were used to develop a diffusional creep model based on bulk (Nabarro-Herring) and grain boundary (Coble) diffusion processes. It was found that irradiation enhanced Nabarro-Herring creep is dominant at low temperatures, while Coble creep dominates for high temperatures. The model compares well against available experimental data and has been implemented in BISON. A demonstration case using simple power profiles has been carried out, showing that negligible creep occurs due to the low temperatures experienced by U₃Si₂, a consequence of its high thermal conductivity.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Li2O-Based Cathode Additives Enabling Prelithiation of Si Anodes

Low first-cycle Coulombic efficiency is especially poor for silicon (Si)-based anodes due to the high surface area of the Si-active material and extensive electrolyte decomposition during the initial cycles forming the solid electrolyte interphase (SEI). Therefore, developing successful prelithiation methods will greatly benefit the development of lithium-ion batteries (LiBs) utilizing Si anodes. In pursuit of this goal, in this study, lithium oxide (Li2O) was added to a LiNi0.6Mn0.2Co0.2O2 (NMC622) cathode using a scalable ball-milling approach to compensate for the initial Li loss at the anode. Different milling conditions were tested to evaluate the impact of particle morphology on the additive performance. In addition, Co3O4, a well-known oxygen evolution reaction catalyst, was introduced to facilitate the activation of Li2O. The Li2O + Co3O4 additives successfully delivered an additional capacity of 1116 mAh/gLi2O when charged up to 4.3 V in half cells and 1035 mAh/gLi2O when charged up to 4.1 V in full cells using Si anodes.

25 ENERGY STORAGE↗
DOE OSTI2023

CMOS-Compatible Ultrathin Superconducting NbN Thin Films Deposited by Reactive Ion Sputtering on 300 mm Si Wafer

We report a milestone in achieving large-scale, ultrathin (~5 nm) superconducting NbN thin films on 300 mm Si wafers using a high-volume manufacturing (HVM) industrial physical vapor deposition (PVD) system. The NbN thin films possess remarkable structural uniformity and consistently high superconducting quality across the entire 300 mm Si wafer, by incorporating an AlN buffer layer. High-resolution X-ray diffraction and transmission electron microscopy analyses unveiled enhanced crystallinity of (111)-oriented δ-phase NbN with the AlN buffer layer. Notably, NbN films deposited on AlN-buffered Si substrates exhibited a significantly elevated superconducting critical temperature (~2 K higher for the 10 nm NbN) and a higher upper critical magnetic field or H c2 (34.06 T boost in H c2 for the 50 nm NbN) in comparison with those without AlN. These findings present a promising pathway for the integration of quantum-grade superconducting NbN films with the existing 300 mm CMOS Si platform for quantum information applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Theoretical Prediction of Thermal Expansion Anisotropy for Y 2 Si 2 O 7 Environmental Barrier Coatings Using a Deep Neural Network Potential and Comparison to Experiment

Environmental barrier coatings (EBCs) are an enabling technology for silicon carbide (SiC)-based ceramic matrix composites (CMCs) in extreme environments such as gas turbine engines. However, the development of new coating systems is hindered by the large design space and difficulty in predicting the properties for these materials. Density Functional Theory (DFT) has successfully been used to model and predict some thermodynamic and thermo-mechanical properties of high-temperature ceramics for EBCs, although these calculations are challenging due to their high computational costs. In this work, we use machine learning to train a deep neural network potential (DNP) for Y 2 Si 2 O 7 , which is then applied to calculate the thermodynamic and thermo-mechanical properties at near-DFT accuracy much faster and using less computational resources than DFT. We use this DNP to predict the phonon-based thermodynamic properties of Y 2 Si 2 O 7 with good agreement to DFT and experiments. We also utilize the DNP to calculate the anisotropic, lattice direction-dependent coefficients of thermal expansion (CTEs) for Y 2 Si 2 O 7 . Molecular dynamics trajectories using the DNP correctly demonstrate the accurate prediction of the anisotropy of the CTE in good agreement with the diffraction experiments. In the future, this DNP could be applied to accelerate additional property calculations for Y 2 Si 2 O 7 compared to DFT or experiments.

36 MATERIALS SCIENCE↗
DOE OSTI2024

MOCVD growth of Si-doped α-(AlGa) 2 O 3 on m-plane α-Al 2 O 3 substrates

We reported the growth of (AlGa) 2 O 3 layers on ($10\overline{10}$) α-Al 2 O 3 substrates using cold-wall metalorganic chemical vapor deposition, and the electrical characterization of Si-doped (AlGa) 2 O 3 layers. In the Ga 2 O 3 growth, the α phase was dominant at low growth temperature, achieving the growth rate of 2.4 μm h –1 at 650 °C. Sheet resistance and electrical conductivity of the Ga 2 O 3 layers with a Si concentration of 3 × 10 20 cm –3 were 1 × 10 4 Ω/square and 8.3 S cm –1 , respectively, at the measurement temperature of 500 °C. The Al composition in the (AlGa) 2 O 3 layers was controlled from 0% to 74%. In our initial attempts, we obtained electrically conductive α-(AlGa) 2 O 3 layers by Si doping (2 × 10 –9 S cm –1 in the sample with an Al composition of 56%). Finally, hybrid functional calculations suggest the conductivities are limited by compensation of Si through cation vacancy complexes, and not by the significant amounts of co-incorporated C and N that are predicted to be electrically passivated by hydrogen.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Activity coefficients of siderophile elements in Fe-Si liquids at high pressure

Metallic core formation in differentiated bodies in the inner solar system can take place between low pressures (near 1 bar) to much higher pressures (up to 100 GPa). Most thermodynamic models of metal-silicate equilibria utilise activity coefficients for metallic tracers in Fe liquids, nearly all of which have been carried out at low pressures. This study focuses on the effect of pressure on activity coefficients for Au, P, V, Mn, Ga, Zn, Cd, Sn, W, Pb, and Nb in liquid Fe-Si alloys. From a series of experiments at 10 GPa, 2373 K containing variable Si content in a metallic liquid we have derived epsilon interaction parameters in Fe-Si liquids ($ε^{Si}_{M}$). Comparison of 1 GPa and 10 GPa data shows no difference except for Nb. Epsilon parameters derived from low pressure experiments can thus be used to calculate activity coefficients for application to higher pressure processes (at least to 10 GPa).

58 GEOSCIENCES↗
DOE OSTI2020

MULTI-DIMENSIONAL MODELING OF THE CFR ENGINE FOR THE INVESTIGATION OF SI NATURAL GAS COMBUSTION AND CONTROLLED END-GAS AUTOIGNITION

Engine knock and misfire are barriers to pathways leading to high-efficiency Spark-Ignited (SI) Natural Gas engines. The general tendency to knock is highly dependent on engine operating conditions and the fuel reactivity. The problem is further complicated by low emission limits and the wide range of chemical reactivity in pipeline quality natural gas. Depending on the region and the source of the natural gas, its reactivity, described by its methane number (analogous to the octane number for liquid SI fuels) can span from 65 - 95. In order to realize diesel-like efficiencies, SI natural gas engines must be designed to operate at high BMEP near knock limits over a wide range of fuel reactivity. This requires a deep understanding regarding the combustion-engine interactions pertaining to flame propagation and end-gas autoignition (EGAI). However, EGAI, if controlled, provides an opportunity to increase SI natural gas engine efficiency by increasing combustion rate and the total burned fuel, mitigating the effects of the slow flame speeds of natural gas fuels which generally reduce BMEP and increase unburned hydrocarbon emissions. For this reason, in order to study EGAI phenomenon, the present work highlights multi-dimensional computational fluid dynamics (CFD) models of the Cooperative Fuel Research (CFR) engine. The CFR engine models are used to investigate fuel-engine interactions that lead to EGAI with natural gas, including effects of fuel reactivity, engine operating parameters, and exhaust gas recirculation (EGR). A Three-Pressure Analysis, performed with GT-Power, was used to estimate initial and boundary conditions for the three-dimensional CFD model. CONVERGE CFD v2.4 was used for the three-dimensional CFD modeling where the level set G-Equation model and SAGE detailed chemical kinetics solver were used. An assessment of the different modeling approaches is also provided to evaluate their limitations, advantages and disadvantages, and for which situations they are most applicable. Model validation was performed with experimental data taken with a CFR engine over varying compression ratio, CA50, EGR fraction, and IMEP and shows good agreement in Peak Cylinder Pressure (PCP), PCP crank angle, and the location of the 10%, 50%, and 90% mass fraction burned (CA10, CA50, and CA90, respectively). The models can predict the onset crank angle and pressure rise rate for light, medium, and heavy EGAI under a variety of fuel reactivities and engine operating conditions.

Bestel, Diego↗
DOE OSTI2022

Room Temperature, Dip Coating Organic Passivation for c-Si Surfaces

Surface passivation of crystalline Si (c-Si) to reduce recombination rate is crucial to obtain high-efficiency c-Si solar cells. A fast passivation technique that can be performed at room temperature is needed when studying the degradation behaviors using various characterization methods to not destroy the degraded states. In this contribution, we explore Nafion via dip coating on n-type Cz wafers. We show that both the Nafion concentration and the conditions of surface and edge affect the passivation quality, and we achieve excellent passivation quality of iVoc of 716 mV, with a saturation current density (J0) of 7 fA/cm2. Additionally, electron paramagnetic resonance (EPR) shows Nafion can be used under cryogenic temperature and reveals the reduction of Si dangling bond after Nafion treatment.

dielectric solar cell↗
DOE OSTI2024

Effect of Si Content in Electrode and SiO2 Additions to the Slag during Electroslag Remelting

Evolution of Si concentration in 316 stainless steel electrodes was observed during a melting campaign consisting of recycling electroslag remelted (ESR) ingots to make new electrodes using vacuum induction melting (VIM). This campaign consisted of iterations of VIM + ESR operations to optimize melting parameters. The effect of Si content on the melt parameters and ingot quality was further evaluated and additions of SiO2 to the slag chemistry were studied using research-scale experiments, x-ray diffraction (XRF), combustion analysis, visual inspections, and computational tools. The Si concentration was found to decrease by approximately 600 ppm following ESR of 150 lb. research-scale electrodes. Eventually, this led to failure of the slag skin and direct ingot/crucible contact. Additions of SiO2 to the slag at levels matching the original calculated Si concentration in the electrode did not eliminate the slag skin failure and the current during steady state increased to maintain a constant melt rate. In this investigation, we propose a mechanism of slag skin failure consisting of local concentration of current density due to absence, or breakage, of the SiO2 layer around the molten metal drop during ESR. This theory was reinforced by additional experiments in which Nb was added to the electrode to change the structure of the oxide layer around the drops.

Jablonski, Paul↗
DOE OSTI2023

High-voltage monocrystalline Si photovoltaic minimodules based on poly -Si/SiO x passivating contacts for high-power laser power conversion

By using photovoltaic cells under high-intensity laser illumination, much higher photoconversion efficiencies are obtained than under the solar spectrum. Here we demonstrate a monocrystalline Si based minimodule to convert laser light into electricity using edge-illuminated Si "minicells" based on polysilicon on silicon oxide passivating contacts. Ten fully metallized devices were stacked in series and illuminated from the edge, creating a high-voltage, low-current minimodule that mitigates resistive and Auger-Meitner losses. The minimodule shows a high open-circuit voltage of >5 V when tested under 1-Sun illumination and >7 V at higher illumination intensities when tested with a flash simulator. The fill factor in these minimodules is limited by shunting at low illuminations but reaches a maximum of ~78% for higher illumination intensities >40 Suns (current density >1200 mA/cm 2 ), indicating that the minimodules are not limited by series resistance up to 40 Suns. Under 1000 nm monochromatic light, we measure efficiencies >40% at > 40 Suns equivalent illumination, showing the potential of passivated contact Si cells for laser power conversion.

14 SOLAR ENERGY↗
DOE OSTI2024

Fluoro‐Ethylene‐Carbonate Plays a Double‐Edged Role on the Stability of Si Anode‐Based Rechargeable Batteries During Cycling and Calendar Aging

Abstract The energy storage density of Li‐ion batteries can be improved by replacing graphite anodes with high‐capacity Si‐based materials, though instabilities have limited their implementation. Performance degradation mechanisms that occur in Si anodes can be divided into cycling stability (capacity retention after repeated battery cycles) and calendar aging (shelf life). While cycling instabilities and improvement strategies have been researched intensively, there is little known about the underlying mechanisms that cause calendar aging. In this work, multiple electron microscope techniques are used to explore the mechanism that governs calendar aging from the sub‐nanometer‐to‐electrode scale. Plasma focused ion beam tomography is used to create 3D reconstructions of calendar aged electrodes and revealed the growth of a LiF‐rich layer at the interface between the copper current collector and the silicon material, which can lead to delamination and increased interfacial impendence. The LiF layer appeared to derive from the fluoro‐ethylene‐carbonate electrolyte additive, which is commonly used to improve cycling stability in Si‐based systems. The results reveal that additives necessary to improve cycling stability can cause performance degradation over the long‐term during calendar aging. The results show that high performing, stable systems require careful design to simultaneously mitigate both cycling and calendar aging instabilities.

25 ENERGY STORAGE↗
DOE OSTI2020

Deformation-enhanced hierarchical multiscale structure heterogeneity in a Pd-Si bulk metallic glass

Here, the multiscale structures in a Pd 82 Si 18 binary bulk metallic glass before and after deformation were studied using electron microscopies, high-energy synchrotron X-ray diffraction, and small-angle scattering techniques. The experimental results revealed an enhancement of hierarchical structure heterogeneities on multiple length scales after deformation. Hierarchical multiple shear bands of high number density were observed after bending, introducing complex but periodically distributed residual strain. Pair distribution function analysis revealed that the connectivity of the short-range clusters on the medium-range scale determines the packing density difference between the tension side and the compression side in the sample after bending. In-situ synchrotron X-ray diffraction study also revealed a transformation of connection modes among short-range clusters under uniaxial tension and compression, which is consistent with those of triaxial tension/compression parts upon bending in Pd 82 Si 18 glassy alloys. The nanoscale heterogeneities for metallic glasses after deformation observed by small-angle scattering and transmission electron microscopy may be attributed to the nanoscale amorphous phase separation and interacting multiple shear bands enhanced by plastic deformation. Our findings suggested that the enhancement of hierarchical heterogeneous structure on multiple length scales may explain the excellent plasticity of Pd-Si glassy alloys, deepening the understanding of structure-property relation during plastic deformation in metallic glasses.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Nonequilibrium defect-phase nanostructures stabilized by irradiation in undersaturated Ni-Si nanocrystalline alloy

Nanocrystalline thin films of the undersaturated alloy Ni-8.5 at% Si were subjected to 2 MeV Ti irradiation at temperatures ranging from 450˚C to 550˚C. Correlative microscopy combining transmission electron microscopy (TEM), scanning-TEM and atom probe tomography (APT revealed that large dose irradiation at 450˚C of samples with initial grain sizes below 100 nm stabilized a novel nanostructure which surprisingly contained three co-existing phases, the γ face-centered-cubic (FCC) matrix, γ' L12 ordered precipitates on intragranular dislocation loops and Ni 31 Si 12 precipitates at triple junctions (TJs). In contrast, irradiation at 550˚C and irradiation of larger grain-size samples at 450˚C only produced a γ-γ' two-phase coexistence. Analysis of the three-phase nanostructure and phase field simulations indicates that radiation-induced segregation is most pronounced at TJs, thus triggering the formation of Ni 31 Si 12 precipitates. These incoherent precipitates, in turn, are expected to stabilize the grain size under irradiation. The results are generalized using the concept of driven defect-phases. It is suggested that the stabilization of driven defect-phases may impart radiation resilience by providing localized relaxation modes to the microstructure evolution during and after temporary perturbations in irradiation conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Crystal structure of the $τ_{11}$ Al 4 Fe 1.7 Si phase from neutron diffraction and ab initio calculations

The intermetallic τ 11 Al 4 Fe 1.7 Si phase is of interest for high-temperature structural application due to its combination of low density and high strength. We determine the crystal structure of the τ 11 phase through a combination of powder neutron diffraction and density functional theory calculations. Using Pawley and Rietveld refinements of the neutron diffraction data provides an initial crystal structure model. Since Al and Si have nearly identical neutron scattering lengths, we use density-functional calculations to determine their preferred site occupations. The τ 11 phase exhibits a hexagonal crystal structure with space group P6 3 /mmc and lattice parameters of a = 7.478 Å and c = 7.472 Å. The structure comprises five Wyckoff positions; Al occupies the 6h and 12k sites, Fe the 2a and 6h sites, and Si the 2a sites. Here we observe site disorder and partial occupancies on all sites with a large fraction of 80% Fe vacancies on the 2d sites, indicating an entropic stabilization of the τ 11 phase at high temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Hydrogen Stability and Bonding in SiN x and Al 2 O 3 Dielectric Stacks on Poly-Si/SiO x Passivating Contacts

Polycrystalline Si on SiO x passivating contacts enables some of the highest efficiency single-junction Si photovoltaic devices, but the high-temperature firing process needed for industrial metallization can significantly reduce passivation. We show that after firing, the implied open-circuit voltage, iV oc , for the Al 2 O 3 /SiN x /poly-Si/SiO x /c-Si stack is 20-30 mV higher than the SiNx/Al 2 O 3 /poly-Si/SiO x /c-Si stack and therefore provides better passivation of the SiO x /c-Si interface. Using effusion measurements and Fourier transform infrared spectroscopy, we demonstrate that more than twice as much hydrogen is retained in the dielectric up to the peak firing temperature of ~800 degrees C for Al 2 O 3 -capped structures. If the Al 2 O 3 layer is not present in the stack, after firing, the iVoc is lower by 50-100 mV compared to Al 2 O 3 /SiN x or SiN x /Al 2 O 3 stacks. These studies will inform future work on the role of dielectrics in aiding the passivation of poly-Si/SiO x passivating contacts.

08 HYDROGEN↗
DOE OSTI2020

Extreme shear-deformation-induced modification of defect structures and hierarchical microstructure in an Al–Si alloy

Abstract Extreme shear deformation is used for several material processing methods and is unavoidable in many engineering applications in which two surfaces are in relative motion against each other while in physical contact. The mechanistic understanding of the microstructural evolution of multi-phase metallic alloys under extreme shear deformation is still in its infancy. Here, we highlight the influence of shear deformation on the microstructural hierarchy and mechanical properties of a binary as-cast Al-4 at.% Si alloy. Shear-deformation-induced grain refinement, multiscale fragmentation of the eutectic Si-lamellae, and metastable solute saturated phases with distinctive defect structures led to a two-fold increase in the flow stresses determined by micropillar compression testing. These results highlight that shear deformation can achieve non-equilibrium microstructures with enhanced mechanical properties in Al–Si alloys. The experimental and computational insights obtained here are especially crucial for developing predictive models for microstructural evolution of metals under extreme shear deformation.

36 MATERIALS SCIENCE↗