Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “REFLECTOR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Effect of antimony nano-scale surface-structures on a GaSb/AlAsSb distributed Bragg reflector

Effects of antimony crystallization on the surface of GaSb during low temperature molecular beam epitaxy growth are investigated. The geometry of these structures is studied via transmission electron and atomic force microscopies, which show the surface metal forms triangular-shaped, elongated nano-wires with a structured orientation composed entirely of crystalline antimony. By depositing antimony on a GaSb/AlAsSb distributed Bragg reflector, the field is localized within the antimony layer. Polarization dependent transmission measurements are carried out on these nano-structures deposited on a GaSb/AlAsSb distributed Bragg reflector. It is shown that the antimony-based structures at the surface favor transmission of light polarized perpendicular to the wires.

36 MATERIALS SCIENCE↗

AlP/GaP distributed Bragg reflectors

Distributed Bragg reflectors with high reflectivity bands centered at wavelengths from 530 to 690 nm (green to red) based on AlP/GaP quarter-wave stacks are prepared on (001)GaP using gas-source molecular-beam epitaxy. Additionally, the complex refractive index of AlP is measured using spectroscopic ellipsometry within the range of 330-850 nm in order to facilitate an accurate reflector design. Structures consisting of 15 quarter-wave stacks reach a peak reflectance between 95% and 98%, depending on the spectral position of the maximum.

36 MATERIALS SCIENCE↗

Polarization- and angle-dependent characteristics in two dimensional photonic crystal membrane reflectors

We report here measured angle- and polarization-dependent reflection properties in two-dimensional photonic crystal broadband membrane reflectors. Polarization independent reflection was obtained at surface normal direction. High reflection can also be obtained for one transverse electric (TE) polarization state over a wide range of incident angles. With the target of 1550 nm spectral band, the measured spectral bandwidths for TE polarization with reflectivity greater than 90% are 180 nm and 56 nm at surface normal and oblique incidence of 45°, respectively. The experimental spectrum approximates the theoretical spectral response of this membrane reflector.

36 MATERIALS SCIENCE↗

Effect of non-uniform slow wave structure in a relativistic backward wave oscillator with a resonant reflector

This paper provides a fresh insight into the effect of non-uniform slow wave structure (SWS) used in a relativistic backward wave oscillator (RBWO) with a resonant reflector. Compared with the uniform SWS, the reflection coefficient of the non-uniform SWS is higher, leading to a lower modulating electric field in the resonant reflector and a larger distance to maximize the modulation current. Moreover, for both types of RBWOs, stronger standing-wave field takes place at the rear part of the SWS. In addition, besides Cerenkov effects, the energy conversion process in the RBWO strongly depends on transit time effects. Thus, the matching condition between the distributions of harmonic current and standing wave field provides a profound influence on the beam-wave interaction. In the non-uniform RBWO, the region with a stronger standing wave field corresponds to a higher fundamental harmonic current distribution. Particle-in-cell simulations show that with a diode voltage of 1.02 MV and beam current of 13.2 kA, a microwave power of 4 GW has been obtained, compared to that of 3 GW in the uniform RBWO.

43 PARTICLE ACCELERATORS↗

Optimal design of one-dimensional photonic crystal back reflectors for thin-film silicon solar cells

For thin-film silicon solar cells (TFSC), a one-dimensional photonic crystal (1D PC) is a good back reflector (BR) because it increases the total internal reflection at the back surface. We used the plane-wave expansion method and the finite difference time domain (FDTD) algorithm to simulate and analyze the photonic bandgap (PBG), the reflection and the absorption properties of a 1D PC and to further explore the optimal 1D PC design for use in hydrogenated amorphous silicon (a-Si:H) solar cells. With identified refractive index contrast and period thickness, we found that the PBG and the reflection of a 1D PC are strongly influenced by the contrast in bilayer thickness. Additionally, light coupled to the top three periods of the 1D PC and was absorbed if one of the bilayers was absorptive. By decreasing the thickness contrast of the absorptive layer relative to the non-absorptive layer, an average reflectivity of 96.7% was achieved for a 1D PC alternatively stacked with a-Si:H and SiO{sub 2} in five periods. This reflectivity was superior to a distributed Bragg reflector (DBR) structure with 93.5% and an Ag film with 93.4%. n-i-p a-Si:H solar cells with an optimal 1D PC-based BR offer a higher short-circuit current density than those with a DBR-based BR or an AZO/Ag-based BR. These results provide new design rules for photonic structures in TFSC.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Embeded photonic crystal at the interface of p-GaN and Ag reflector to improve light extraction of GaN-based flip-chip light-emitting diode

In this experiment, a flip-chip light-emitting diode with photonic crystal was fabricated at the interface of p-GaN and Ag reflector via nanospheres lithography technique. In this structure, photonic crystal could couple with the guide-light efficiently by reason of the little distance between photonic crystal and active region. The light output power of light emitting diode with embedded photonic crystal was 1.42 times larger than that of planar flip-chip light-emitting diode. Moreover, the embedded photonic crystal structure makes the far-field divergence angle decreased by 18° without spectra shift. The three-dimensional finite difference time domain simulation results show that photonic crystal could improve the light extraction, and enhance the light absorption caused by Ag reflector simultaneously, because of the roughed surface. The depth of photonic crystal is the key parameter affecting the light extraction and absorption. Light extraction efficiency increases with the depth photonic crystal structure rapidly, and reaches the maximum at the depth 80 nm, beyond which light extraction decrease drastically.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Optimization of relativistic backward wave oscillator with non-uniform slow wave structure and a resonant reflector

This letter optimizes synchronously 18 parameters of a relativistic backward wave oscillator with non-uniform slow wave structure (SWS) and a resonant reflector by using the parallel genetic algorithms and particle-in-cell simulation. The optimization results show that the generation efficiency of microwave from the electron beam has increased 32% compared to that of the original device. After optimization, the electromagnetic mode propagating in the resonant changes from the original TM{sub 020} mode of reflector to higher-order TM{sub 021} mode, which has a high reflection coefficient in a broader frequency range than that of the former. The modulation of current inside the optimized device is much deeper than that in the original one. The product of the electric field and current is defined. Observing this product, it is found that the interaction of the electron beam with the electromagnetic wave in the optimized device is much stronger than that in the original device, and at the rear part of SWS of the optimized device, the electron beam dominantly gives out the energy to the electromagnetic wave, leading to the higher generation efficiency of microwave than that of the original device.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Hybrid grating reflectors: Origin of ultrabroad stopband

Hybrid grating (HG) reflectors with a high-refractive-index cap layer added onto a high contrast grating (HCG) provide a high reflectance close to 100% over a broader wavelength range than HCGs. The combination of a cap layer and a grating layer brings a strong Fabry-Perot (FP) resonance as well as a weak guided mode (GM) resonance. Most of the reflected power results from the FP resonance, while the GM resonance plays a key role in achieving a reflectance close to 100% as well as broadening the stopband. An HG sample with 7 InGaAlAs quantum wells included in the cap layer has been fabricated by directly wafer-bonding a III-V cap layer onto a Si grating layer. Its reflection property has been characterized. This heterogeneously integrated HG reflector may allow for a hybrid III-V on Si laser to be thermally efficient, which has promising prospects for silicon photonics light sources and high-speed operation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Distributed Bragg reflectors obtained by combining Se and Te compounds: Influence on the luminescence from CdTe quantum dots

We report on the optical properties of structures containing self assembled CdTe quantum dots (QDs) combined with Te and Se based distributed Bragg reflectors either in a half cavity geometry with a relatively broad cavity mode or in a full cavity geometry where the cavity mode is much narrower. We show that for both structures the extraction coefficient of the light emitted from the QDs ensemble is enhanced by more than one order of magnitude with respect to the QDs grown on a ZnTe buffer. However, a single QD line broadening is observed and attributed to an unintentional incorporation of Se in the vicinity of the CdTe QDs. We show that postponing the QDs growth for 24 h after the distributed Bragg reflector deposition allows recovering sharp emission lines from individual QDs. This two step growth method is proven to be efficient also for the structures with CdTe QDs containing a single Mn{sup 2+} ion.

36 MATERIALS SCIENCE↗

Switchable and tunable film bulk acoustic resonator fabricated using barium strontium titanate active layer and Ta{sub 2}O{sub 5}/SiO{sub 2} acoustic reflector

A solidly mounted acoustic resonator was fabricated using a Ba{sub 0.60}Sr{sub 0.40}TiO{sub 3} (BST) film deposited by metal organic chemical vapor deposition. The device was acoustically isolated from the substrate using a Bragg reflector consisting of three pairs of Ta{sub 2}O{sub 5}/SiO{sub 2} layers deposited by chemical solution deposition. Transmission electron microscopy verified that the Bragg reflector was not affected by the high temperatures and oxidizing conditions necessary to process high quality BST films. Electrical characterization of the resonator demonstrated a quality factor (Q) of 320 and an electromechanical coupling coefficient (K{sub t}{sup 2}) of 7.0% at 11 V.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Realization of a Distributed Bragg Reflector for Propagating Guided Matter Waves

We report on the experimental study of a Bragg reflector for guided, propagating Bose-Einstein condensates. A one-dimensional attractive optical lattice of finite length created by red-detuned laser beams selectively reflects some velocity components of the incident matter wave packet. We find quantitative agreement between the experimental data and one-dimensional numerical simulations and show that the Gaussian envelope of the optical lattice has a major influence on the properties of the reflector. In particular, it gives rise to multiple reflections of the wave packet between two symmetric locations where Bragg reflection occurs. Our results are a further step towards integrated atom-optics setups for quasi-cw matter waves.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Laser damage of crazed electron-beam high-reflectors following infrared and ultraviolet irradiation in the nanosecond pulse regime

Laser damage of optical components can be a limiting factor in scaling the energetics of high-peak and average power laser systems. Specifically for optical coatings, damage under nanosecond pulsed irradiation is initiated by pre-existing defects in the coating layers, including those that cause discontinuities in the structure, like craze lines. Crazing or cracking in a multilayer dielectric optical coating is induced when the overall coating stress is sufficiently tensile, and is an occasionally observed issue when employing more porous deposition techniques like electron-beam evaporation. Here, in this study, electron-beam high-reflectors were fabricated utilizing process parameters that are known to induce crazing based on prior processing history to systematically evaluate the impact of crazing on reflector damage performance for 1064 and 355 nm lasers. The crazing that was observed was apparently nucleated at nodular defects. When the cross-section of these nodules was investigated, it was observed that there were cracks into the fused silica substrate of approximately 5 µm in depth. The craze lines were irradiated with 1064 and 355 nm light at fluences slightly above the onset of damage initiation fluence of the coating. The 1064 nm irradiated sub-apertures exhibit laser damage but with no spatial correlation with the craze line, whereas the 355 nm irradiated area exhibited many damage sites along the craze line. Finite-difference time-domain electric-field simulations were conducted, and ∼2× field amplification in hafnia was observed for the 355 nm wavelength case. The laser damage can be attributed to a slight electric-field intensification coincidental with an area where UV damage-prone precursors are known to occur. The 355 nm laser damage in uncoated fused silica substrates has been previously correlated to initiate through localized UV absorption at the broken silica bonds in the tips of fractures.

Harthcock, Colin [Lawrence Livermore National Labo↗

Single-mode, narrow-linewidth external cavity quantum cascade laser through optical feedback from a partial-reflector

An external-cavity (EC) quantum cascade (QC) laser using optical feedback from a partial-reflector is reported. With this configuration, the otherwise multi-mode emission of a Fabry-Perot QC laser was made single-mode with optical output powers exceeding 40 mW. A mode-hop free tuning range of 2.46 cm-1 was achieved by synchronously tuning the EC length and QC laser current. The linewidth of the partial-reflector EC-QC laser was measured for integration times from 100 μs to 4 s, and compared to a distributed feedback QC laser. Linewidths as small as 480 kHz were recorded for the EC-QC laser

(140.3410) Laser resonators↗

Amorphous silicon carbide high contrast gratings as highly efficient spectrally selective visible reflectors

We report spectrally selective visible wavelength reflectors using hydrogenated amorphous silicon carbide (a-SiC:H) as a high index contrast material. Beyond 610nm and through the near infrared spectrum, a-SiC:H exhibits very low loss and exhibits an wavelength averaged index of refraction of n = 3.1. Here we design, fabricate, and characterize such visible reflectors using a hexagonal array of a-SiC:H nanopillars as wavelength-selective mirrors with a stop-band of approximately 40 nm full-width at half maximum. The fabricated high contrast grating exhibits reflectivity R >94% at a resonance wavelength of 642nm with a single layer of a-SiC:H nanopillars. The resonance wavelength is tunable by adjusting the geometrical parameters of the a-SiC:H nanopillar array, and we observe a stop-band spectral center shift from 635 nm up to 642 nm. High contrast gratings formed from a-SiC:H nanopillars are a promising platform for various visible wavelength nanophotonics applications.

Bauser, Haley C.↗

Benchmark Measurements of the BeRP Ball in Various Reflectors

Details of benchmark neutron multiplicity measurements of the 4.484 kg Beryllium Reflected Plutonium (BeRP) ball inside of various reflectors. Measurements were performed with an Ortec Fission Meter neutron multiplicity counter. Measurements were made of the bare BeRP Ball, the BeRP Ball inside 3 inch thick polyethylene, nickel, and tungsten, and the polyethylene with an additional 2 inch thick steel reflector. For every measurement, the mass m S of 240 Pu, k eff , multiplication M, and escape multiplication ME are reported. For each individual measurement, the measured mass mS of 240 Pu in the BeRP Ball was within 20.7 grams (closest edge of measurement errorbar to closest edge of errorbar for reference mS from isotopics). The combined measurement of the mass of 240 Pu m S = 267 ± 7 grams which compared very favorably to the known value from isotopics of m S = 266.8 ± 0.5 grams.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Reflectors for SAR Performance Testing – second edition

Synthetic Aperture Radar (SAR) performance testing and estimation is facilitated by observing the system response to known target scene elements. Trihedral corner reflectors and other canonical targets play an important role because their Radar Cross Section (RCS) can be calculated analytically. However, reflector orientation and the proximity of the ground and mounting structures can significantly impact the accuracy and precision with which measurements can be made. These issues are examined in this report.

42 ENGINEERING↗

Correcting Cross-polarization Monopulse Response of Reflector Antennas

The monopulse response of radar systems utilizing a short-focal-length offset-fed parabolic reflector can be compromised by depolarization of the signal by the target and by multipath scattering from nearby objects. The polarimetric behavior of this type of antenna is examined. The use of a shroud to reduce multipath interaction with nearby objects is also described. The mechanism through which man-made targets can introduce cross-polarization components into the scattered field is explained. Two kinds of polarization filters, suitable for linear polarization, are described for mitigating the effects of depolarization due to cross-polarization scattering. The benefit of the application of a polarization filter is demonstrated by modeling a monopulse radar system viewing a dihedral corner reflector. The model demonstrates dramatic performance improvement when the filter is used, showing that usable performance can be achieved even when the target depolarization is so severe that the cross-polarized signal is more than an order of magnitude stronger than the desired co-polarized signal. Relevant and useful reference material is also included in the form of appendices describing the relationship between different polarization representations and demonstrating the conditions under which Maxwell's equations can be considered to be scale-invariant.

47 OTHER INSTRUMENTATION↗

Calculation of Helium Coolant Behavior in A Single Cooling Channel in MHTGR Reflector Region During Pressurized Conduction Cooldown Scenario Using the COMSOL Multiphysics Code

The objective of the calculation performed and discussed in this report was to examine the behavior of the helium flow through a single cooling channel in the modular high-temperature gas-cooled reactor (MHTGR) core during a pressurized conduction cooling scenario (PCC). The region of interest for the single cooling channel flow calculation is in the upper reflector blocks. Flow from the upper reflector blocks, during the PCC scenario, moves upward and into the upper plenum.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗