Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Quality by Design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Spraylon fluorocarbon encapsulation for silicon solar cell arrays, phase 3

The liquid transparent film-forming, fluorocarbon, Spraylon, a protective coating for terrestrial solar cell modules was evaluated. Two modules were completed and field tested. Problems developed early in the field testing which led to the shortened test period, specifically, lifting of the antireflection coating, followed in some areas by complete film delamination. It is believed that although these problems were certainly induced by the presence of the SPRAYLON film, they were not failures of the material per se. Instead, assembly procedures, module design, and cell coating quality should be evaluated to determine cause of failure.

Naes, L. G.↗
NASA NTRS1980

Subsonic stability and control flight test results of the Space Shuttle /tail cone off/

The subsonic stability and control testing of the Space Shuttle Orbiter in its two test flights in the tailcone-off configuration is discussed, and test results are presented. Flight test maneuvers were designed to maximize the quality and quantity of stability and control data in the minimal time allotted using the Space Shuttle Functional Simulator and the Modified Maximum Likelihood Estimator (MMLE) programs, and coefficients were determined from standard sensor data sets using the MMLE, despite problems encountered in timing due to the different measurement systems used. Results are included for lateral directional and longitudinal maneuvers as well as the Space Shuttle aerodynamic data base obtained using the results of wind tunnel tests. The flight test data are found to permit greater confidence in the data base since the differences found are well within control system capability. It is suggested that the areas of major differences, including lateral directional data with open speedbrake, roll due to rudder and normal force due to elevon, be investigated in any further subsonic flight testing. Improvements in sensor data and data handling techniques for future orbital test flights are indicated.

Cooke, D. R.↗
NASA NTRS1981

Design, development, and field demonstration of a remotely deployable water quality monitoring system

A prototype water quality monitoring system is described which offers almost continuous in situ monitoring. The two-man portable system features: (1) a microprocessor controlled central processing unit which allows preprogrammed sampling schedules and reprogramming in situ; (2) a subsurface unit for multiple depth capability and security from vandalism; (3) an acoustic data link for communications between the subsurface unit and the surface control unit; (4) eight water quality parameter sensors; (5) a nonvolatile magnetic bubble memory which prevents data loss in the event of power interruption; (6) a rechargeable power supply sufficient for 2 weeks of unattended operation; (7) a water sampler which can collect samples for laboratory analysis; (8) data output in direct engineering units on printed tape or through a computer compatible link; (9) internal electronic calibration eliminating external sensor adjustment; and (10) acoustic location and recovery systems. Data obtained in Saginaw Bay, Lake Huron are tabulated.

Wallace, J. W.↗
NASA NTRS1981

An analytical pilot rating method for highly elastic aircraft

An analytical method was developed to predict pilot ratings for highly elastic aircraft subject to severe mode interactions between rigid body and elastic dynamics. An extension of the standard optimal control model of pilot response was made to include the hypothesis that the pilot controls the system with an internal model consisting of the slowly varying part of the aircraft dynamics. This modified optimal control model was analytically evaluated for a longitudinal pitch tracking task on a large flexible aircraft. Parametric variations in the undamped natural frequencies of two symmetric elastic modes were made to induce varying amounts of mode interaction. The model proved successful in discriminating when the pilot can or cannot visually separate rigid from elastic pitch response in the turbulence excited tracking task. This method shows considerable promise in making it possible to investigate such mode interaction effects on handling qualities in the preliminary design stage of new aircraft.

Swaim, R. L.↗
NASA NTRS1981

An innovative air data system for the Space Shuttle Orbiter - Data analysis techniques

The Shuttle Entry Air Data System (SEADS) is an experimental system designed to supply research quality air data and to meet Orbiter operational air data requirements throughout entry. SEADS incorporates no mechanical devices but is based on the concept that the fuselage proper, whether symmetrical or not, can be instrumented so as to function both as a pitot-static probe and as a differential pressure flow direction sensor. Specifically SEADS consists of 20 flush orifices, each routed to a pair of absolute pressure transducers. A computational technique has been developed capable of extracting air data parameters solely from surface pressure measurements. The digital filtering algorithm implemented in SEADS is the natural adaptation to air data sensing of a technology widely used in navigation, guidance, and control systems.

Pruett, C. D.↗
NASA NTRS1981

Using CAD/CAM to improve productivity - The IPAD approach

Progress in designing and implementing CAD/CAM systems as a result of the NASA Integrated Programs for Aerospace-Vehicle Design is discussed. Essential software packages have been identified as executive, data management, general user, and geometry and graphics software. Data communication, as a means to integrate data over a network of computers of different vendors, provides data management with the capability of meeting design and manufacturing requirements of the vendors. Geometry software is dependent on developmental success with solid geometry software, which is necessary for continual measurements of, for example, a block of metal while it is being machined. Applications in the aerospace industry, such as for design, analysis, tooling, testing, quality control, etc., are outlined.

Fulton, R. E.↗
NASA NTRS1983

Ride quality systems for commuter aircraft

The state-of-the-art in Active Ride Augmentation, specifically in terms of its feasibility for commuter aircraft applications. A literature survey was done, and the principal results are presented here through discussion of different Ride Quality Augmentation System (RQAS) designs and advances in related technologies. Recommended follow-on research areas are discussed, and a preliminary RQAS configuration for detailed design and development is proposed.

Downing, D. R.↗
NASA NTRS1983

Large-area sheet task: Advanced dendritic-web-growth development

Thermally generated stresses in the growing web crystal were reduced. These stresses, which if too high cause the ribbon to degenerate, were reduced by a factor of three, resulting in the demonstrated growth of high-quality web crystals to widths of 5.4 cm. This progress was brought about chiefly by the application of thermal models to the development of low-stress growth configurations. A new temperature model was developed which can analyze the thermal effects of much more complex lid and top shield configurations than was possible with the old lumped shield model. Growth experiments which supplied input data such as actual shield temperature and melt levels were used to verify the modeling results. Desirable modifications in the melt level-sensing circuitry were made in the new experimental web growth furnace, and this furnace has been used to carry out growth experiments under steady-state conditions. New growth configurations were tested in long growth runs at Westinghouse AESD which produced wider, lower stress and higher quality web crystals than designs previously used.

Duncan, C. S.↗
NASA NTRS1983

Effects of control saturation on the command response of statically unstable aircraft

Hanson and Stengel (1981) have described the effects of saturating controls on the initial-condition response of statically unstable aircraft. In an analysis of the stability augmentation system, consideration was given to maximizing the region of stable response. The present investigation is concerned with an extension of the control saturation analysis to the problem of command response, taking into account the main problem of control design for satisfactory flying qualities (as perceived by the pilot). A model for examining the effects of control saturation on longitudinal stability and command response is developed and applied to an aircraft with a static instability. Three parameters prescribing longitudinal flying qualities are examined with respect to their ability to identify proper flying qualities in the presence of control saturation. The presented analysis provides also satisfactory guidelines for establishing command saturation/stability boundaries.

Hanson, G. D.↗
NASA NTRS1984

Asymmetric spline surfaces - Characteristics and applications

Asymmetric spline surfaces appear useful for the design of high-quality general optical systems (systems without symmetries). A spline influence function defined as the actual surface resulting from a simple perturbation in the spline definition array shows that a subarea is independent of others four or more points away. Optimization methods presented in this paper are used to vary a reflective spline surface near the focal plane of a decentered Schmidt-Cassegrain to reduce rms spot radii by a factor of 3 across the field.

Stacy, J. E.↗
NASA NTRS1978

Advanced composite stabilizer for Boeing 737 aircraft

Activities related to development of an advanced composites stabilizer for the Boeing 737 commercial transport are reported. Activities include discussion of the design and weight status, stiffness requirements, the finite element model, test programs, quality assurance, and manufacturing producibility studies. Design details of the graphite/epoxy components are virtually complete. Emphasis is placed on the metal and fiberglass trailing edge components. The bending and torsional stiffness properties are satisfactory for both stability/control and for flutter requirements. The finite element model input geometry is revised to reflect the latest changes to production drawings.

Source record↗
NASA NTRS1984

Joined-wing research airplane feasibility study

The joined wing is a new type of aircraft configuration which employs tandem wings arranged to form diamond shapes in plan view and front view. Wind-tunnel tests and finite-element structural analyses have shown that the joined wing provides the following advantages over a comparable wing-plus-tail system; lighter weight and higher stiffness, higher span-efficiency factor, higher trimmed maximum lift coefficient, lower wave drag, plus built-in direct lift and direct sideforce control capability. To verify these advantages at full scale a manned research airplane is required. A study has therefore been performed of the feasibility of constructing such an airplane, using the fuselage and engines of the existing NAA AD-1 oblique-wing airplane. Cost and schedule constraints favored converting the AD-1 rather than constructing a totally new airframe. By removing the outboard wing panels the configuration can simulate wings joined at 60, 80, or 100 percent of span. For maximum versatility the aircraft has alternative control surfaces (such as ailerons and elevators on the front and/or rear wings), and a removeable canard to explore canard/joined-wing interactions at high-lift conditions. Design, performance, and flying qualities are discussed.

Wolkovitch, J.↗
NASA NTRS1988

Analytical determination of critical crack size in solar cells

Although solar cells usually have chips and cracks, no material specifications concerning the allowable crack size on solar cells are available for quality assurance and engineering design usage. Any material specifications that the cell manufacturers use were developed for cosmetic reasons that have no technical basis. Therefore, the Applied Solar Energy Corporation (ASEC) has sponsored a continuing program for the fracture mechanics evaluation of GaAs. Fracture mechanics concepts were utilized to develop an analytical model that can predict the critical crack size of solar cells. This model indicates that the edge cracks of a solar cell are more critical than its surface cracks. In addition, the model suggests that the material specifications on the allowable crack size used for Si solar cells should not be applied to GaAs solar cells. The analytical model was applied to Si and GaAs solar cells, but it would also be applicable to the semiconductor wafers of other materials, such as a GaAs thin film on a Ge substrate, using appropriate input data.

Chen, C. P.↗
NASA NTRS1989

An expert system to advise astronauts during experiments

Work being done on an expert system designed to improve the quality of space experimentation in vestibular physiology is described. Emphasis is given to two of the several modules of which the system architecture is composed: the Protocol Manager and the Interesting Data Filter. Some engineering issues related to human factors and to data acquisition and monitoring are also addressed.

Young, Laurence R.↗
NASA NTRS1993

Summary of the effects of engine throttle response on airplane formation-flying qualities

A flight evaluation was conducted to determine the effect of engine throttle response characteristics on precision formation-flying qualities. A variable electronic throttle control system was developed and flight-tested on a TF-104G airplane with a J79-11B engine at the NASA Dryden Flight Research Facility. This airplane was chosen because of its known, very favorable thrust response characteristics. Ten research flights were flown to evaluate the effects of throttle gain, time delay, and fuel control rate limiting on engine handling qualities during a demanding precision wing formation task. Handling quality effects of lag filters and lead compensation time delays were also evaluated. The Cooper and Harper Pilot Rating Scale was used to assign levels of handling quality. Data from pilot ratings and comments indicate that throttle control system time delays and rate limits cause significant degradations in handling qualities. Threshold values for satisfactory (level 1) and adequate (level 2) handling qualities of these key variables are presented. These results may provide engine manufacturers with guidelines to assure satisfactory handling qualities in future engine designs.

Walsh, Kevin R.↗
NASA NTRS1994

Teacher Enhancement Institute

In a team building, team teaching strategy with four faculty, can learning strategies such as educational technology and problem based learning be provided to forty local teachers of primary, elementary, and secondary students? The impetus for the effort is to provide information about science and engineering at NASA and motivate students to pursue careers in science and technology. Teachers, identified and selected through a rigorous application procedure, participated in a two week workshop for a graduate credit. Teachers were exposed to computer applications such as INTERNET, MOSAIC, Power Machintosh word processing, NASA scientists, and laboratory experiments. Teachers were evaluated on level and quality of their participation, design of teacher application materials and relevant lesson plans and presentations. The results show that teachers, regardless of preparation and background, can learn science and engineering applications and develop relevant materials to transfer information to their classroom. Follow-up during the academic year will show that teachers are successfully using materials.

Simmons, Ron W.↗
NASA NTRS1998

Improving Customer Satisfaction in an R and D Environment

Satisfying customer needs is critical to the sustained competitive advantage of service suppliers. It is therefore important to understand the types of customer needs which, if fulfilled or exceeded, add value and contribute to overall customer satisfaction. This study identifies the needs of various research and development (R&D) customers who contract for engineering and design support services. The Quality Function Deployment (QFD) process was used to organize and translate each customer need into performance measures that, if implemented, can improve customer satisfaction. This study also provides specific performance measures that will more accurately guide the efforts of the engineering supplier. These organizations can either implement the QFD methodology presented herein or extract a few performance measures that are specific to the quality dimensions in need of improvement. Listening to 'what' customers talk about is a good first start.

Alexander, Anita↗
NASA NTRS1980

Space Coatings for Industry

Ball Aerospace developed entirely new space lubrication technologies. A new family of dry lubricants emerged from Apollo, specifically designed for long life in space, together with processes for applying them to spacecraft components in microscopically thin coatings. Lubricants worked successfully on seven Orbiting Solar Observatory flights over the span of a decade and attracted attention to other contractors which became Ball customers. The company has developed several hundred variations of the original OSO technology generally designed to improve the quality and useful life of a wide range of products or improve efficiency of the industrial processes by which such products are manufactured.

Source record↗