Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Pressure effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

The emission characteristics of uranium hexafluoride at high temperatures

Relative emission measurements were made for UF6/Argon mixtures heated in a plasma torch over a range of temperatures from 800 to about 3600 K over a wavelength range from 80 to 600 nm. Total pressures were varied from 1 to approximately 1.7 atm. Similarly absorption measurements were carried out in the visible region from 420 to 580 nm over a temperature range from about 1000 to 1800 K. Total pressure for these measurements was 1.0 atm. The emission results exhibited relatively no emission at wavelengths below 250 nm over the range of temperatures investigated. At temperatures in excess of 1800 K an additional emission band centered at 310 nm appears and becomes more well defined at higher temperatures. Essentially no pressure effect was observed with respect to emission at pressures up to 1.7 atm.

Krascella, N. L.↗
NASA NTRS2014

Investigation of the Effects of Facility Background Pressure on the Performance and Voltage-Current Characteristics of the High Voltage Hall Accelerator

The National Aeronautics and Space Administration (NASA) Science Mission Directorate In-Space Propulsion Technology office is sponsoring NASA Glenn Research Center to develop a 4 kW-class Hall thruster propulsion system for implementation in NASA science missions. A study was conducted to assess the impact of varying the facility background pressure on the High Voltage Hall Accelerator (HiVHAc) thruster performance and voltage-current characteristics. This present study evaluated the HiVHAc thruster performance in the lowest attainable background pressure condition at NASA GRC Vacuum Facility 5 to best simulate space-like conditions. Additional tests were performed at selected thruster operating conditions to investigate and elucidate the underlying physics that change during thruster operation at elevated facility background pressure. Tests were performed at background pressure conditions that are three and ten times higher than the lowest realized background pressure. Results indicated that the thruster discharge specific impulse and efficiency increased with elevated facility background pressure. The voltage-current profiles indicated a narrower stable operating region with increased background pressure. Experimental observations of the thruster operation indicated that increasing the facility background pressure shifted the ionization and acceleration zones upstream towards the thrusters anode. Future tests of the HiVHAc thruster are planned at background pressure conditions that are expected to be two to three times lower than what was achieved during this test campaign. These tests will not only assess the impact of reduced facility background pressure on thruster performance, voltage-current characteristics, and plume properties; but will also attempt to quantify the magnitude of the ionization.

Pressure Effects↗
NASA NTRS2021

Transient evolution of basal drag during glacier slip

Glacier slip is usually described using steady-state sliding laws that relate drag, slip velocity and effective pressure, but where subglacial conditions vary rapidly transient effects may influence slip dynamics. Here we use results from a set of laboratory experiments to examine the transient response of glacier slip over a hard bed to velocity perturbations. The drag and cavity evolution from lab experiments are used to parameterize a rate-and-state drag model that is applied to observations of surface velocity and ice-bed separation from the Greenland ice sheet. The drag model successfully predicts observed lags between changes in ice-bed separation and sliding speed. These lags result from the time (or displacement) required for cavities to evolve from one steady-state condition to another. In comparing drag estimates resulting from applying rate-and-state and steady-state slip laws to transient data, we find the peaks in drag are out of phase. This suggests that in locations where subglacial conditions vary on timescales shorter than those needed for cavity adjustment transient slip processes control basal drag.

Glacier↗
NASA NTRS1974

Radiation pressure and air drag effects on the orbit of the balloon satellite 1963 30D

Computed orbits of the balloon satellite 1963 30D are given every 2 days over an interval of 456 days near the beginning of the satellite's lifetime and an interval of 824 days near the end of its lifetime. The effects of radiation pressure on the satellite are examined in some detail. It is found that the variations in all the elements can be represented by use of a single parameter to specify the effect of diffuse reflection from the satellite's surface, and that this parameter remains constant, or nearly so, during the entire 7-year lifetime. Success in obtaining a consistent representation of the radiation-pressure effects is ascribed to the inclusion of the effects of terrestrial radiation pressure, using a model for the earth's albedo that includes seasonal and latitudinal variations. Anomalous effects in the orbital acceleration, as well as in the other elements, are represented quite well by including a small force at right angle to the solar direction and by allowing this to rotate about the solar direction. This implies that the satellite is aspherical, that it is rotating, and that the axis of rotation precesses.

Slowey, J. W.↗
NASA NTRS1975

Evaluation by step response tests of prototype relief valves designed for YF-12 inlet stability bleed system

Two stability bleed system relief valves were tested in a special dynamic test facility. These poppet valves are prototypes for a stability bleed system designed for use in a YF-12 flight inlet. One valve is unshielded, while the other has a special shield to eliminate the flow effect pressures on the piston. The tests determined the size of a damping orifice to be used during wind tunnel tests of the bleed system and verified an analog simulation of the valves. The effects of initial pressure level, pressure step size, and spring rate were investigated.

Dustin, M. O.↗
NASA NTRS1973

Correlation and prediction of gaseous diffusion coefficients.

A new correlation method for binary gaseous diffusion coefficients from very low temperatures to 10,000 K is proposed based on an extended principle of corresponding states, and having greater range and accuracy than previous correlations. There are two correlation parameters that are related to other physical quantities and that are predictable in the absence of diffusion measurements. Quantum effects and composition dependence are included, but high-pressure effects are not. The results are directly applicable to multicomponent mixtures.

Marrero, T. R.↗
DOE OSTI2025

Effects of equilibrium pressure on plasma response to RMPs in a spherical tokamak

This study presents a comprehensive analysis of the equilibrium pressure on the plasma response to resonant magnetic perturbations (RMPs) in the spherical tokamak (ST) MAST-U, employing both single-fluid and MHD-kinetic hybrid models (implemented via the MARS-F/K codes). As a key finding, the study identifies two different pressure-driven eigenmodes, exhibiting Sturmian property, that affect the Troyon no-wall limits for the onset of the n = 1 and n = 2 ( n is the toroidal mode number) ideal external kink instabilities as well as the corresponding plasma response to the applied RMP. With increasing equilibrium pressure, the plasma response to RMPs is significantly enhanced in the ST plasma, particularly in the high-pressure regime where kinetic effects strongly stabilize the external kink instability. The Troyon no-wall limit divides the plasma response into two regions: well below the limit, the response amplitudes and trends (versus pressure) are similar between the fluid and kinetic models; as the equilibrium pressure approaches the Troyon limit, the kinetic model predicts significant amplification of the RMP field, up to 30 times for cases considered. A relatively weak dependence of the optimal coil phasing on the equilibrium pressure is computed in this ST plasma, similar to the trend obtained for the conventional aspect ratio devices. These findings underscore the importance of incorporating kinetic effects in accurate prediction of the plasma response to RMPs in high-pressure ST tokamak plasmas and provide a theoretical basis for optimizing RMP-based control of the edge-localized modes in future ST devices.

RMP↗
DOE OSTI2026

Thermal loading effects on chalk hydromechanical behavior for nuclear waste disposal

Safe disposal of heat-generating nuclear waste depends on host rock stability under thermal, hydrological, and mechanical stresses. This study investigates the effect of thermal loading on mechanical behavior of the shallowly buried Ghareb formation chalk through triaxial and hydrostatic constant strain rate and creep tests at temperatures up to 100 ˚C and effective pressures up to 20.7 MPa. Experimental results show that thermal loading reduces the elastic moduli of chalk by 50–75%, and a transition occurs above 60 ˚C where creep rates increase rapidly. Water saturation nearly doubles the thermally induced strain compared to dry conditions and strongly decreases material rigidity. Thermal loading also leads to significant pore pressure increases under undrained conditions and leads to reductions in the apparent permeability during drained conditions. Laboratory experimental data were used to parameterize and develop a preliminary constitutive model for predicting future deformation during repository operations in the Ghareb. The strongly coupled effects – mechanical weakening, fluid pressure fluctuations, and permeability modification – demonstrate that elevated repository temperatures will have a pronounced effect on the near field Ghareb behavior during waste disposal operations. The findings indicate that the coupled interactions must be considered in predictive models and repository design to ensure long-term nuclear waste isolation and safety.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Thermodynamic analysis of a two-stage binary-fluid ejector heat pump water heater

Ejector heat pump water heaters (EHPWHs) could significantly increase the thermal efficiency of domestic water heating and reduce greenhouse gas emissions. This study addresses two major technical barriers to using EHPWHs in domestic water heating—low heating cycle coefficient of performance (COP) and low condensation temperatures—using binary fluid pairs as a working fluid in a two-stage ejector system. A comprehensive, geometry-free model of binary-fluid ejectors was built and validated to predict the entrainment ratios of binary-fluid ejectors. A thermodynamic model of a two-stage binary-fluid ejector EHPWH was built to predict the heating cycle COP of EHPWHs. The performance of the EHPWH was theoretically evaluated using HFE7000 and Novec649 as primary fluids and R600 and R1234ze(Z) as secondary fluids. HFE7000/R600 gave the highest heating cycle COP (i.e., 1.356) in producing domestic hot water at 60.0 °C. An optimum evaporation temperature of the primary fluid was identified for the maximum effective entrainment ratio and effective pressure lift ratio of two-stage ejectors. Here, the effective entrainment ratio of the two-stage ejector dominated the heating cycle COP of the EHPWH. Primary fluids with lower latent heats of evaporation and/or secondary fluids with higher latent heats of evaporation yielded higher heating cycle COPs of EHPWHs.

42 ENGINEERING↗
DOE OSTI2020

High-temperature oxidation of transient-liquid phase bonded Ni-based alloys in 1 bar and 250 bar carbon dioxide

Compact microchannel heat exchanger designs for supercritical CO 2 power cycles are valued for equipment size reduction and increased heat transfer. They can be fabricated via transient-liquid phase (TLP) bonding, which utilizes a lower melting point interlayer for bonding facilitation of etched thin plates. Haynes 230 and 282 TLP bonded stacks were exposed to high-purity CO 2 at 1 bar/700 °C to 4000 h and 250 bar/720 °C (supercritical) to 1500 h. All samples obeyed parabolic kinetics after an oxide buildup stage of 500-1000 h. Mass gains were similar for the base and TLP bonded alloys, and oxide thicknesses and scales did not significantly differ around the TLP bond regions. Furthermore, there were some slight oxide compositional differences for the H282 TLP samples at 250 bar. There was a slight pressure effect on mass gain, as samples exposed at the higher pressure experienced higher initial mass gains, but then slower continued oxide growth.

36 MATERIALS SCIENCE↗
NASA NTRS1980

Pressure dependence of the absolute rate constant for the reaction OH + C2H2 from 228 to 413 K

The pressure dependence of the absolute rate constant for the reaction of the hydroxyl radical with acetylene, important in both atmospheric and combustion chemistry, is determined for temperatures between 228 and 413 K. The flash photolysis-resonance fluorescence technique was employed at five temperatures over wide ranges of pressure and acetylene concentrations, with the OH produced by water photolysis and hydroxyl resonance fluorescent photons measured by multiscaling techniques. Results indicate that, except at the lowest temperature, the bimolecular rate constant for the reaction depends strongly on total pressure, with the pressure effect becoming more pronounced with increasing temperature. At limiting high pressures, the rate constant is found to be equal to 6.83 + or - 1.19 x 10 to the -12th exp (-646 + or - 47/T) cu cm/molecule per sec, where T is the temperature. Results thus demonstrate the importance of environmental conditions in theoretical studies of atmospheric and combustion product compositions

Michael, J. V.↗
NASA NTRS1986

The effect of oxygen pressure on volatility and morphology of LaB6 single crystal cathodes

The effect of oxygen pressure on the volatility and morphology of single crystal LaB6 cathodes, heated to different temperatures, was investigated. At a temperature of 1600 K, an increase of oxygen pressure from 1 x 10 to the -8th torr to 1 x 10 to the -6th torr has led to a 100-fold enhancement in cathode volatility. The enhancement effect of oxygen pressure diminished with increasing temperature: at a cathode operating temperature of 1900 K, the volatility enhancement due to the same oxygen pressure was negligible. It was shown that the faceting frequently observed during evaporation of conically shaped emitters is due to a crystallograpic anisotropy of the oxidation rate of LaB6. No facet formation occurs during evaporation at oxygen pressures below -110 to the -8th torr.

Davis, P. R.↗
DOE OSTI2022

Waste Control Specialists Technical Review Team Report

1. Modeling of Drum 68660 and the WCS Drums: A calibrated model of Los Alamos National Laboratory (LANL) Drum 68660 indicates that pressurization of the drum by restriction of drum venting could have led to the thermal runaway reaction at the Waste Isolation Pilot Plant (WIPP) in 2014, supporting the hypothesis that the contents of the drum were not fundamentally different from the overall remediated nitrate salt (RNS) waste stream. 2. Nitric Acid Reactions and Aging of the Waste: The stability of the WCS RNS waste with respect to autocatalytic thermal runaway due to nitric acid chemistry should increase over time as the nitric acid is depleted from chemical reactions in the drum. However, this cannot be confirmed because of the lack of long-term experimental data on the impact of aging on the reactivity of RNS waste. The calibrated model indicates that the waste drums retain most of their reactive components, metal nitrate salts and sWheat Scoop ® , even after eight years. 3. Pressure Effects and Runaway Reactions: The calibrated model indicates that if the drums and standard waste boxes (SWBs) are not allowed to pressurize during transport or storage and they are stored at historical WIPP repository temperatures, then an autocatalytic thermal runaway event is not expected to occur. Since the cause of Drum 68660 pressurization is not known, decision makers are not able to tailor mitigating strategies to the initiating event. Consequently, mitigating strategies must consider all feasible internal and external events that could lead to the pressurization of the drums. 4. Temperature Effects and Runaway Reactions: Temperature also has a strong influence on the stability of the waste. The calibrated model indicates that cooling the drums or SWBs can reduce the possibility of autocatalytic thermal runaway reactions. Simulations suggest that for a drum with a plugged vent, the probability of thermal runaway may be reduced or eliminated if wastes are maintained at or below 43 °F through active cooling measures from the initiation of transport until emplacement at WIPP.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Pressure induced Invar effect in Fe 55 ⁢Ni 45 : An experimental study with nuclear resonant scattering

Pressure-dependent synchrotron x-ray diffraction (XRD), nuclear resonant inelastic x-ray scattering (NRIXS), and nuclear forward scattering (NFS) measurements were made on 57 Fe 55 Ni 45 . XRD measurements were at 298 and 392 K at pressures up to 20 GPa, confirming a pressure-induced Invar effect between 7 and 13 GPa. A decrease of the 57 Fe magnetic moment was found in NFS measurements under pressure, showing an increase in magnetic entropy. The 57 Fe phonon density of states (DOS) was obtained from NRIXS measurements. The low thermal expansion in the high-pressure Invar region originates from a competition between the thermal expansion from spins and phonons as calculated from Maxwell relations. Finally, the longitudinal phonon modes changed their pressure dependence near the Curie transition, which is evidence for a spin-phonon interaction.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

A Comparative Experimental Analysis of Natural Gas Dual Fuel Combustion Ignited by Diesel and Poly OxyMethylene Dimethyl Ether

Dual-fuel low-temperature combustion is a possible solution for alleviating the tradeoff between oxides of nitrogen and soot emissions in conventional diesel combustion, albeit with poor combustion stability, high carbon monoxide, and unburned hydrocarbon emissions at low engine loads. The present work compares emissions and combustion (heat release and other metrics) of both diesel and poly-oxy methylene dimethyl ether as high-reactivity fuels to ignite natural gas while leveraging spray-targeted reactivity stratification, which involved multiple injections of the high-reactivity fuels. The experiments included six parametric sweeps of: (1) start of first injection, (2) start of second injection, (3) percentage of energy substitution of natural gas, (4) commanded injection duration ratio, (5) rail pressure, and (6) intake pressure. The experiments were performed on a 1.8 L heavy-duty single-cylinder research engine operating at a medium speed of 1339 rev/min. Not-to-exceed limits for the indicated oxides of nitrogen emissions, maximum pressure rise rate, and the coefficient of variation of the indicated mean effective pressure were set to 1 g/kWh, 10 bar/CAD, and 10%, respectively. The indicated emissions decreased and combustion improved significantly for both fueling combinations when the experimental procedure was applied.

Partridge, Kendyl Ryan↗