Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Pinch effect.”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Energy use of piperazine with the advanced stripper from pilot plant testing

Here, piperazine with the Advanced Stripper (PZAS™) was tested at the National Carbon Capture Center (NCCC) at coal and NGCC conditions. Energy performance was measured with accounting for heat loss. The net heat duty was found to be identical at 2.45 GJ/tonne for both 4 and 12% CO 2 at 90% CO 2 removal. The average measured heat loss was 0.38 GJ/tonne and represented 30% of the gross heat rate. For PZAS, the warm rich piping before the control valve is the largest in surface area. Heat loss at this location increased heat duty by 80% of the heat loss value. Therefore, the total heat duty was decreased by 80% of the heat loss. The Independence™ model was validated using 112 steady-state pilot plant runs and predicted average net heat duty with an error of 9% and lean loading with an error of 10%. The model was used to simulate process impacts of heat loss for the PZAS and simple stripper configurations. For both strippers, heat loss was found to impact heat duty at locations other than just the steam heater. While heat loss in the steam heater was the most important for PZAS, heat loss in the column was the most important for the simple stripper due to a large top-side pinch and CO 2 reabsorption at the same location. CO 2 reabsorption in PZAS occurred only at high heat loss values (~0.14 GJ/hr), compared to low heat loss values (~ 0.03 GJ/hr) in the PZ-simple stripper. Excessive packing in the PZ-simple stripper caused a large top-side pinch at 0.23 mol/mol lean loading, making the column very sensitive to heat loss. Heat loss in the PZ-simple stripper increased heat duty by 120–150% at typical heat loss values and lean loading of 0.23 mol/mol. Heat loss in the MEA-simple stripper only increased heat duty by 1–13% in a typical lean loading range of 0.1–0.2 mol/mol. A large bottom side pinch at low lean loading for 7 m MEA made the effect of heat loss less pronounced.

42 ENGINEERING↗

Magnetic curvature effects on plasma interchange turbulence

The magnetic curvature effects on plasma interchange turbulence and transport in the Z-pinch and dipole-like systems are explored with two-fluid global simulations. By comparing the transport levels in the systems with a different magnetic curvature, we show that the interchange-mode driven transport strongly depends on the magnetic geometry. For the system with large magnetic curvature, the pressure and density profiles are strongly peaked in a marginally stable state and the nonlinear evolution of interchange modes produces the global convective cells in the azimuthal direction, which lead to the low level of turbulent convective transport.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Observation of fast expansion velocity with insulating tungsten wires on ∼80 kA facility

This paper presents experimental results on the effects of insulating coatings on tungsten planar wire array Z-pinches on an 80 kA, 100 ns current facility. Expansion velocity is obviously increased from ∼0.25 km/s to ∼3.5 km/s by using the insulating coatings. It can be inferred that the wire cores are in gaseous state with this fast expansion velocity. An optical framing camera and laser probing images show that the standard wire arrays have typical ablation process which is similar to their behaviors on mega-ampere facilities. The ablation process and precursor plasma are suppressed for dielectric tungsten wires. The wire array implosion might be improved if these phenomena can be reproduced on Mega-ampere facilities.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Leading order QCD shear viscosity from the three-particle irreducible effective action

In this article we calculate the leading order shear viscosity in QCD using the resummed three-particle irreducible effective action. We work to 3-loop order in the effective action. We show that the integral equations that resum the pinch and collinear contributions are produced naturally by the formalism. All leading order terms are included, without the need for any kind of power counting arguments.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

On the Evolution From Micrometer-Scale Inhomogeneity to Global Overheated Structure During the Intense Joule Heating of a z-Pinch Rod

Ultrafast optical microscopy of metal z-pinch rods pulsed with megaampere current is contributing new data and critical insight into what provides the fundamental seed for the magneto-Rayleigh-Taylor (MRT) instability. A two-frame near infrared/visible intensified-charge-coupled device gated imager with 2-ns temporal resolution and 3-μm spatial resolution captured emissions from the nonuniformly Joule heated surfaces of ultrasmooth aluminum (Al) rods. Nonuniform surface emissions are consistently first observed from discrete, 10-μm scale, subelectronvolt spots. Aluminum 6061 alloy, with micrometer-scale nonmetallic resistive inclusions, forms several times more spots than 99.999% pure Al 5N; 5-10 ns later, azimuthally stretched elliptical spots and distinct strata (40-100 μm wide by 10 μm tall) are observed on Al 6061, but not on Al 5N. In such overheat strata, aligned parallel to the magnetic field, we find that they are highly effective seeds for MRT instability growth. Our data give credence to the hypothesis that early nonuniform Joule heating, such as the electrothermal instability, may provide the dominant seed for MRT.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Observation of the Kondo effect in a spin-3/2 hole quantum dot

We report the observation of the Kondo effect in a spin-3/2 hole quantum dot formed near pinch-off in a GaAs quantum wire. We clearly observe two distinctive hallmarks of quantum dot Kondo physics. First, the zero-bias peak in the differential conductance splits an in-plane magnetic field and the splitting is independent of gate voltage. Second, the splitting rate is twice as large as that for the lowest one-dimensional subband. We show that the Zeeman splitting of the zero-bias peak is highly anisotropic and attribute this to the strong spin-orbit interaction for holes in GaAs.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Realistic Earth matter effects and a method to acquire information about small {theta}{sub 13} in the detection of supernova neutrinos

In this paper, we first calculate the realistic Earth matter effects in the detection of type II supernova neutrinos at the Daya Bay reactor neutrino experiment which is currently under construction. It is found that the Earth matter effects depend on the neutrino incident angle {theta}, the neutrino mass hierarchy {delta}m{sub 31}{sup 2}, the crossing probability at the high resonance region inside the supernova, P{sub H}, the neutrino temperature, T{sub {alpha}}, and the pinching parameter in the neutrino spectrum, {eta}{sub {alpha}}. We also take into account the collective effects due to neutrino-neutrino interactions inside the supernova. With the expression for the dependence of P{sub H} on the neutrino mixing-angle {theta}{sub 13}, we obtain the relations between {theta}{sub 13} and the event numbers for various reaction channels of supernova neutrinos. Using these relations, we propose a possible method to acquire information about {theta}{sub 13} smaller than 1.5 deg. Such a sensitivity cannot be achieved by the reactor neutrino deta at the Daya Bay experiment which has a sensitivity of the order of {theta}{sub 13}{approx}3 deg. Furthermore, we apply this method to other neutrino experiments, i.e. Super-K, SNO, KamLAND, LVD, MinBooNE, Borexino, and Double-Chooz. We also study the energy spectra of the differential event numbers, dN/dE.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Ion dynamics driven by a strongly nonlinear plasma wake

Abstract In plasma wakefield accelerators, the wave excited in the plasma eventually breaks and leaves behind slowly changing fields and currents that perturb the ion density background. We study this process numerically using the example of a Facility for Advanced aCcelerator Experimental Tests (FACET) experiment where the wave is excited by an electron bunch in the bubble regime in a radially bounded plasma. Four physical effects underlie the dynamics of ions: (1) attraction of ions toward the axis by the fields of the driver and the wave, resulting in formation of a density peak, (2) generation of ion-acoustic solitons following the decay of the density peak, (3) positive plasma charging after wave breaking, leading to acceleration of some ions in the radial direction, and (4) plasma pinching by the current generated during the wave-breaking. The interplay of these effects results in the formation of various radial density profiles, which are difficult to produce in any other way.

Physics↗

Reversal of particle flux in collisional-finite beta tokamak discharges

The mixed gradient method [Zhong et al. Phys. Rev. Lett. 111, 265001 (2013)] is adopted and effects of collisions and finite beta are included in the Weiland 9-equation fluid model. The particle flux and particle pinch, obtained using the Weiland anomalous transport fluid model, are compared with Tore Supra experimental results. Particle transport is also studied using predictive simulation data for an experimental advanced superconducting tokamak discharge in which neutral beam heating is utilized. The effects of collisions on particle transport are studied by turning collisions on and off in the Weiland model. It is found that the particle pinch region is related to the mode structure. The particle pinch region coincides with the region where the strong ballooning modes are present due to large gradients. The general properties of the fluid model are examined by finding regions where collisions can enhance the particle pinch.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Magnetic Field Measurements in Wire-Array Z-Pinches using Magneto-Optically Active Waveguides

Understanding the magnetic field topology in wire-array Z-pinches as a function of time is of great significance to understanding these high-energy density plasmas especially for their ultimate application to stockpile stewardship and inertial confinement fusion. We are developing techniques to measure magnetic fields as a function of space and time using Faraday rotation of a single longitudinal mode (SLM) laser through a magneto-optically active bulk waveguide (multicomponent terbium borate glass) placed adjacent to, or within, the wire array in 1 MA experiments. We have measured fields >10 T with 100 ns rise times outside of a wire-array for the entire duration of the current pulse and as much as {approx}2 T inside a wire-array for {approx}40 ns from the start of current. This is the first time that such rapidly varying and large fields have been measured using these materials. In a dense Z-pinch, these sensing devices may not survive for long but may provide the magnetic field at the position of the sensor that can be used to corroborate magnetic probes, with which we compare our results.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A monolithic mass tracking formulation for bubbles in incompressible flow

We devise a novel method for treating bubbles in incompressible flow that relies on the conservative advection of bubble mass and an associated equation of state in order to determine pressure boundary conditions inside each bubble. We show that executing this algorithm in a traditional manner leads to stability issues similar to those seen for partitioned methods for solid–fluid coupling. Therefore, we reformulate the problem monolithically. This is accomplished by first proposing a new fully monolithic approach to coupling incompressible flow to fully nonlinear compressible flow including the effects of shocks and rarefactions, and then subsequently making a number of simplifying assumptions on the air flow removing not only the nonlinearities but also the spatial variations of both the density and the pressure. The resulting algorithm is quite robust, has been shown to converge to known solutions for test problems, and has been shown to be quite effective on more realistic problems including those with multiple bubbles, merging and pinching, etc. Notably, this approach departs from a standard two-phase incompressible flow model where the air flow preserves its volume despite potentially large forces and pressure differentials in the surrounding incompressible fluid that should change its volume. Our bubbles readily change volume according to an isothermal equation of state.

97 MATHEMATICS AND COMPUTING↗

Overview of density pedestal structure: Role fueling versus transport

How much of the density pedestal structure profile is determined by fueling versus transport is still a valid question. In most current tokamaks, the Scrape-Off Layer is not opaque enough to screen the neutrals and limit their penetration past the separatrix. As such recycled neutrals as well as additional gas puffing can directly affect the pedestal structure through ionization. Yet, in ITER and other future burning plasma magnetic confinement devices, this ionization source will be pushed further out into the Scrape-Off Layer. This poses the question, how much of the pedestal density structure is governed by this edge ionization source versus plasma transport effects. Theoretically, several turbulent modes have been identified which could provide a 'pinch' like up-gradient transport mechanism. Up-gradient transport is necessary in a source-free region to obtain a peaked density profile, which is often observed in the core of tokamaks. In an opaque Scrape-Off Layer, without the existence of such a pinch, the pedestal density structure would eventually disappear. Not only would this limit our ability to fuel a fusion reactor, it would also affect the pedestal stability. In this paper we will give an overview of the state of the art on what sets the pedestal density structure based on experimental observations as well as theoretical models. We will complement these studies with new results from Alcator C-Mod and DIII-D where the opaqueness is increased to reach values similar to those in ITER.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Cleated Print Surface for Fused Deposition Modeling

Fused Deposition Modeling (FDM) has become popular among Additive Manufacturing technologies due to its speed, geometric scalability, and low cost; however, the primitive nature of the FDM build surface fundamentally limits the utility of FDM in terms of reliability, autonomy, and material selection. Currently, FDM relies on adhesive forces between the first layer of a print and the build surface; depending on the materials involved, this adhesive bond may or may not be reliable. Thermal contraction between the build plate and build materials can break that bond, which causes warpage and delamination of the part from the build surface and subsequent failure of the part. Furthermore, with each print, the user must use tools or manual maneuvering to separate the printed part from the build surface as well as retexture or replace the used build surface. In this paper, we present a novel build platform that allows for a mechanical bond between the print and build surface by using dovetail-shaped features. The first layer of the print flows into the features and becomes mechanically captivated by the build platform. Once the print is completed, the platform is rolled or flexed open to release the part from the mechanical bond. This design not only lowers the risk of delamination during printing but also eliminates the need for a user to reset or replace the build surface between print jobs. The effectiveness of each geometry was determined by measuring the distance at the pinch point compared to the distance that the extrusion filled below the pinch point. The captivation ratio was measured to compare the different geometries tested and determine which direction of extrusion creates a better ratio.

42 ENGINEERING↗

Transformational Opacity Platforms on the Z Facility: A Design Study

The goal of this one-year LDRD is to study novel experimental approaches to provide benchmark spectral opacity measurements at the most extreme conditions beyond existing measurements (i.e. 2x temperature, ~5x density). These conditions correspond to those at half the solar radius and would provide a unique and novel test for stellar physics. These conditions are also relevant to advance stockpile stewardship research. The basic idea is to embed a sample inside the z-pinch dynamic hohlraum on the Z facility and obtain its opacity from either 1) its self-emission or 2) its absorption from using a capsule backlighter. This study evaluates the feasibility, limitations to these two approaches from a design approach. We found that emission-based perspective gives, at best, an opacity accuracy of about 20% for the current studied pinch conditions due to the limit of LTE approximation and radiation transport effects. The capsule-backlighter-based approach overcomes this limitation although some specific design questions remain to be answered. Promising designs are proposed for follow-on Z experiments. Future designs would help maintain Z relevancy in relation to ignition-enabled platforms at NIF.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Measurements of high-current electron beams from X pinches and wire array Z pinches

Some issues concerning high-current electron beam transport from the X pinch cross point to the diagnostic system and measurements of the beam current by Faraday cups are discussed. Results of computer simulation of electron beam propagation from the pinch to the Faraday cup give limits for the measured current for beams having different energy spreads. The beam is partially neutralized as it propagates from the X pinch to a diagnostic system, but within a Faraday cup diagnostic, space charge effects can be very important. Experimental results show evidence of such effects.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Fast electron bremsstrahlung in axisymmetric magnetic configuration

The nonthermal bremsstrahlung is calculated in a plasma with arbitrary axisymmetric magnetic configuration, taking into account the relativistic angular anisotropy of the radiation cross section at high photon energies, the helical winding of the field lines on the magnetic flux surfaces, and the poloidal variation of the electron distribution function including particle trapping effects. The fast electron dynamics during current drive in tokamaks and reverse field pinches can be investigated in detail by coupling this calculation to a bounce-averaged relativistic Fokker-Planck solver, which calculates the electron distribution function. The asymmetry between high- and low-field side hard x-ray emission intensity that has been measured on the Tore-Supra tokamak [Equipe TORE SUPRA, in Proceedings of the 15th Conference on Plasma Physics and Controlled Nuclear Fusion Research, Seville (International Atomic Energy Agency, Vienna, 1995) Vol. 1, IAEA-CN-60/A1-5 (Institute of Physics, Bristol, U.K., 1995), p. 105] is explained for the first time by the role of trapped electrons. A much stronger poloidal asymmetry is predicted for the line-integrated fast electron bremsstrahlung in the poloidal plane of the Madison Symmetric Torus [R. N. Dexter et al., Fusion Tech. 19, 131 (1991)], since the helical winding of the magnetic field lines is much larger for a reverse field pinch configuration. In this case, the hard x-ray emission is no longer a flux surface quantity, which prevents local reconstructions using a standard Abel inversion, whatever the geometrical arrangement of the lines of sight.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Spatio-temporal evolution of the L {yields} I {yields} H transition

We investigate the dynamics of the low(L) {yields} high(H) transition using a time-dependent, one dimensional (in radius) model which self-consistently describes the time evolution of zonal flows (ZFs), mean flows (MFs), poloidal spin-up, and density and pressure profiles. The model represents the physics of ZF and MF competition, turbulence suppression via E Multiplication-Sign B shearing, and poloidal flows driven by turbulence. Numerical solutions of this model show that the L{yields}H transition can occur via an intermediate phase (I-phase) which involves oscillations of profiles due to ZF and MF competition. The I-phase appears as a nonlinear transition wave originating at the edge boundary and propagates inward. Locally, I-phase exhibits the characteristics of a limit-cycle oscillation. All these observations are consistent with recent experimental results. We examine the trigger of the L{yields}H transition, by defining a ratio of the rate of energy transfer from the turbulence to the zonal flow to the rate of energy input into the turbulence. When the ratio exceeds order unity, ZF shear gains energy, and a net decay of the turbulence is possible, thus triggering the L{yields}H transition. Numerical calculations indicate that the L{yields}H transition is triggered by this peak of the normalized ZF shearing. Zonal flows act as 'reservoir,' in which to store increasing fluctuation energy without increasing transport, thus allowing the mean flow shear to increase and lock in the transition. A counterpart of the L {yields} I{yields}H transition, i.e., an L{yields}H transition without I-phase, is obtained in a fast power ramp, for which I-phase is compressed into a single burst of ZF, which triggers the transition. Effects of neutral charge exchange on the L{yields}H transition are studied by varying ZF damping and neoclassical viscosity. Results show that the predicted L{yields}H transition power increases when either ZF damping or viscosity increase, suggesting a link between recycling, ZF damping, and the L{yields}H threshold. Studies of fueling effects on the transition and pedestal structure with an emphasis on the particle pinch are reported.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Considerations for Thermal Annealing of Zr-Alloy Cladding During Dry Storage

In January 2025, the U.S. Department of Energy (DOE) sponsored a technical workshop with fuel vendors that provided a forum for increased collaboration on backend fuel cycle research. The workshop reviewed observations of thermal annealing of irradiated zirconium alloys in simulated dry storage conditions and discussed implications to the industry’s interest in reducing wet storage to optimize operational flexibility and the expected trend of increasing discharge burnup (and decay heats), which could lead to an increase in dry storage temperatures. One approach to accommodate increased decay heats in dry storage is to increase the regulatory temperature limit during dry storage, which is now 400°C. However, this could lead to thermal annealing of the cladding, which will tend to increase creep rates, creep strains, and ductility while decreasing yield strength. These considerations are compounded by bonding between the pellet and cladding at high burnup, which results in the pellet carrying more load during fuel rod deformations, especially in bending, which is the dominant deformation phenomenon in canister drop analyses. Because the U.S. Nuclear Regulatory Commission (NRC) recommends yield strength as a primary failure criterion for accident analyses in storage and transportation, particularly for canister drop scenarios, the purpose of the workshop was to develop options for alternative failure criterion that could replace yield strength in canister drop analyses. Topics discussed were (1) the regulatory framework, (2) the effect of thermal annealing on microhardness and tensile properties of cladding materials, (3) the effect of thermal annealing on fuel rod failure during bending, bending fatigue, and pinch loading, and (4) an alternative failure criterion for canister drop analyses. This paper provides a summary of the key discussions and outcomes of the workshop

Cantonwine, Paul [ORNL] (ORCID:0009000522247033)↗