Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Phase Transformation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

High pressure phase transformation in iron under fast compression

We present experimental results on the solid-solid, {alpha} to {epsilon} phase transformation kinetics of iron under high pressure dynamic compression. We observe kinetic features - velocity loops - similar with the ones recently reported to occur when water is frozen into its ice VII phase under comparable experimental conditions. We analyze this behavior in terms of general ideas coupling the steady sample compression with phase nucleation and growth with a pressure dependent phase interface velocity. The model is used to predict the response of iron when steadily driven across the {alpha} - {epsilon} phase boundary on very short time scales, including those envisioned to be achieved in ultra-fast laser experiments.

36 MATERIALS SCIENCE↗

Ultra-fast dynamic compression technique to study kinetics of phase transformations in Bismuth

Pre-heated Bi was ramp compressed within 30 ns to a peak stress of {approx}11 GPa to explore structural phase transformation kinetics under dynamic loading conditions. Under these ultra-fast compression time-scales the equilibrium Bi I-II phase boundary is overpressurized by {Delta}P {approx} 0.8 GPa. {Delta}P is observed to increase logarithmically with strain rate, {var_epsilon}, above 10{sup 6} s{sup -1}. Estimates from a kinetics model predict that the Bi I phase is fully transformed within 3 ns.

42 ENGINEERING↗

Stress-dependent χ phase transformation in a Ni-based superalloy

The ongoing push to elevate operating temperatures in aerospace gas turbine engines – driven by goals of enhanced fuel efficiency and reduced CO 2 emissions – mandates advancements in the creep resistance of Ni- and Co-based superalloys, which are integral for critical engine components. This study elucidates the role of stress assisted localized phase transformations in the creep properties of these alloys. By leveraging chemo-mechanical coupling, self-healing γ′ precipitates are designed to immobilize planar defects, thereby increasing creep resistance. Employing advanced characterization techniques such as high-resolution Scanning Transmission Electron Microscopy (HR-STEM), in conjunction with atomistic simulations and thermodynamic calculations, novel deformation pathways facilitated by χ local phase transformation (LPT) strengthening have been uncovered; notably, the formation of χ nano-laths through microtwinning and superlattice intrinsic stacking fault (SISF) shearing. This study highlights critical insights into the compositional boundaries necessary for optimizing LPT strengthening while avoiding deleterious bulk formation of η/χ phases. These advancements will guide the design of new alloys maximizing high-temperature creep strength for advanced aerospace applications.

Egan, Ashton J. [Friedrich-Alexander University Er↗

EBSD characterization of high-temperature phase transformations in an Al-Si coating on Cr-Mo steel

5Cr-0.5Mo steel was coated by hot-dipping in a molten bath containing Al-10 wt.% Si. The phase transformation in the aluminide layer during diffusion at 750 Degree-Sign C in static air was analyzed by electron backscatter diffraction. The results show the aluminide layer of the as-coated specimen consisted of an outer Al-Si topcoat, a middle layer formed of scattered {tau}{sub 5(C)}-Al{sub 7}(Fe,Cr){sub 2}Si particles and minor plate-shaped {tau}{sub 4}-Al{sub 4}FeSi{sub 2} and {tau}{sub 6}-Al{sub 4}FeSi phases in the Al-Si matrix and an inner continuous {tau}{sub 5(H)}-Al{sub 7}Fe{sub 2}Si layer, respectively from the coating surface to the steel substrate. The formation of FeAl{sub 3} and Fe{sub 2}Al{sub 5} with {tau}{sub 1}-(Al,Si){sub 5}Fe{sub 3} precipitates can be observed with increasing exposure time at 750 Degree-Sign C. After 5 h of exposure, the Al-Si topcoat has been consumed, and the aluminide layer consisted of Fe{sub 2}Al{sub 5} and a few {tau}{sub 1}-(Al,Si){sub 5}Fe{sub 3} precipitates. The FeAl phase not only formed at the interface between Fe{sub 2}Al{sub 5} and the steel substrate, but also transformed from {tau}{sub 1}-(Al,Si){sub 5}Fe{sub 3} after diffusion for 10 h. With prolonged exposure, the aluminide layer comprised only FeAl{sub 2} and FeAl. - Highlights: Black-Right-Pointing-Pointer EBSD can differentiate phases in aluminide layer with similar chemical compositions. Black-Right-Pointing-Pointer Mapping and EBSPs functions in EBSD provide a reliable phase identification. Black-Right-Pointing-Pointer A phase transformation in the aluminide layer has been described in detail. Black-Right-Pointing-Pointer 5 Fe-Al-Si and 4 Fe-Al intermetallic phases are performed during the diffusion. Black-Right-Pointing-Pointer Cubic {tau}{sub 5(C)}-Al{sub 7} (Fe,Cr){sub 2}Si and hexagonal {tau}{sub 5(H)}-Al{sub 7}(Fe,Cr){sub 2}Si are identified.

36 MATERIALS SCIENCE↗

A study of stress-induced phase transformation and micromechanical behavior of CuZr-based alloy by in-situ neutron diffraction

The stress-induced phase transformation and micromechanical behavior of CuZr-based alloy were investigated by in-situ neutron diffraction. The pseudoelastic behavior with a pronounced strain-hardening effect is observed. The retained martensite nuclei and the residual stress obtained from the 1st cycle reduce the stress threshold for the martensitic transformation. A critical stress level is required for the reverse martensitic transformation from martensite to B2 phase. An increase of intensity for the B2 (110) plane in the 1st cycle is caused by the twinning along the {112}<111> twinning system. The convoluted stress partitioning influenced by the elastic and transformation anisotropy along with the newly formed martensite determines the microstress partitioning of the studied CuZr-based alloy. The reversible martensitic transformation is responsible for the pseudoelasticity. The macro mechanical behavior of the pure B2 phase can be divided into 3 stages, which are mediated by the evolvement of the martensitic transformation. This manuscript has been authored by UT-Battelle, LLC under Contract No. DE-AC05-00OR22725 with the U.S. Department of Energy. The United States Government retains and the publisher, by accepting the article for publication, acknowledges that the United States Government retains a non-exclusive, paid-up, irrevocable, world-wide license to publish or reproduce the published form of this manuscript, or allow others to do so, for United States Government purposes. The Department of Energy will provide public access to these results of federally sponsored research in accordance with the DOE Public Access Plan (http://energy.gov/downloads/doe-public-access-plan).

36 MATERIALS SCIENCE↗

Phase Transformation Contributions to Heat Capacity and Impact on Thermal Diffusivity, Thermal Conductivity, and Thermoelectric Performance

Abstract The accurate characterization of thermal conductivity κ, particularly at high temperature, is of paramount importance to many materials, thermoelectrics in particular. The ease and access of thermal diffusivity D measurements allows for the calculation of κ when the volumetric heat capacity, ρc p , of the material is known. However, in the relation κ = ρc p D , there is some confusion as to what value of c p should be used in materials undergoing phase transformations. Herein, it is demonstrated that the Dulong–Petit estimate of c p at high temperature is not appropriate for materials having phase transformations with kinetic timescales relevant to thermal transport. In these materials, there is an additional capacity to store heat in the material through the enthalpy of transformation Δ H . This can be described using a generalized model for the total heat capacity for a material where φ is an order parameter that describes how much latent heat responds “instantly” to temperature changes. Here, C pφ is the intrinsic heat capacity (e.g., approximately the Dulong–Petit heat capacity at high temperature). It is shown experimentally in Zn 4 Sb 3 that the decrease in D through the phase transition at 250 K is fully accounted for by the increase in c p , while κ changes smoothly through the phase transition. Consequently, reports of κ dropping near phase transitions in widely studied materials such as PbTe and SnSe have likely overlooked the effects of excess heat capacity and overestimated the thermoelectric efficiency, zT .

Agne, Matthias T.↗

Phase Transformations in the Mixed Lithium-Magnesium Imide Li{sub 2}Mg(NH){sub 2}

A statistical theory of structural-phase transformations in imide Li{sub 2}Mg(NH){sub 2} is developed, free energies of three phases of imide α, β, γ are calculated, and their state diagrams are determined. Also, the isotherm, isobar, and isopleth curves are examined. Possible manifestation of the hysteretic effect is demonstrated for α- and β-phases. The results of calculations are compared with the experimental data.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Observations of grain-boundary phase transformations in an elemental metal

The theory of grain boundary (the interface between crystallites, GB) structure has a long history 1 and the concept of GBs undergoing phase transformations was proposed 50 years ago 2,3 . The underlying assumption was that multiple stable and metastable states exist for different GB orientations 4,5,6 . The terminology ‘complexion’ was recently proposed to distinguish between interfacial states that differ in any equilibrium thermodynamic property 7 . Different types of complexion and transitions between complexions have been characterized, mostly in binary or multicomponent systems 8,9,10,11,12,13,14,15,16,17,18,19 . Simulations have provided insight into the phase behaviour of interfaces and shown that GB transitions can occur in many material systems 20,21,22,23,24 . However, the direct experimental observation and transformation kinetics of GBs in an elemental metal have remained elusive. In this work we demonstrate atomic-scale GB phase coexistence and transformations at symmetric and asymmetric $[11\bar{1}]$ tilt GBs in elemental copper. Atomic-resolution imaging reveals the coexistence of two different structures at Σ19b GBs (where Σ19 is the density of coincident sites and b is a GB variant), in agreement with evolutionary GB structure search and clustering analysis 21,25,26 . We also use finite-temperature molecular dynamics simulations to explore the coexistence and transformation kinetics of these GB phases. Our results demonstrate how GB phases can be kinetically trapped, enabling atomic-scale room-temperature observations. Our work paves the way for atomic-scale in situ studies of metallic GB phase transformations, which were previously detected only indirectly 9,15,27,28,29 , through their influence on abnormal grain growth, non-Arrhenius-type diffusion or liquid metal embrittlement.

36 MATERIALS SCIENCE↗

Phase transformation sequence and magnetic properties of melt-spun SmCo-based alloy after isochronal heat treatment

The phase transformation sequence, microstructure and compositions, and magnetic properties for a melt-spun Sm(Co{sub 0.68}Fe{sub 0.2}Cu{sub 0.1}Zr{sub 0.02}){sub 7.5} alloy after isochronal heat treatments have been studied by using x-ray diffraction, transmission electron microscopy, three-dimensional atom probe (3DAP), and magnetometry. The as-spun ribbons had a single phase with the Cu{sub 7}Tb structure. After being aged at 720 deg. C, the single phase decomposed into two major phases: 2:17R and 1:5H, and one minor CoFeZr-rich phase. The formation of the Z-phase happened after the cellular structure, requiring a higher temperature than that for the cellular structure. The 3DAP analysis showed that Zr was depleted from the 2:17R and 1:5H phases by a half while the other elements remained almost unchanged when the aging temperature increased from 720 to 840 deg. C. In contrast to the sintered permanent magnets, Cu was enriched in the 1:5H phase with a much higher concentration (>40 at. %). The Cu enrichment also occurred at the boundary of the Z-phase. The coercivity achieved was H{sub c}=4.34 kOe following aging at 720 deg. C. The highest maximum energy product, (BH){sub max}, was 6.48 MG Oe after aging at 800 deg. C and the remanence to saturation magnetization ratio, M{sub r}/M{sub s}, was 0.69. This relatively low H{sub c} and high M{sub r}/M{sub s} ratio may be a consequence of the formation of a significant volume fraction of the CoFeZr-rich nanocrystalline phase.

36 MATERIALS SCIENCE↗

Phase transformations in the Zn-Al eutectoid alloy after quenching from the high temperature triclinic beta phase

Ribbons of the Zn-Al eutectoid alloy obtained by melt-spinning, were heat treated at 350 deg. C during 30 min in a free atmosphere furnace, and then quenched in liquid nitrogen. The temperature correspond to {beta} phase zone, which has a triclinic crystalline structure [1, 2]. Some evidence, obtained by X-ray diffraction, show that the structures present in the just quenched material are both close-packed hexagonal ({eta}-phase) and rhombohedral (R-phase). X-ray diffractograms taken in the same ribbons after annealed 500 h at room temperature, show that the R phase its transform to {alpha} and {eta} phases.

36 MATERIALS SCIENCE↗

Phase transformation and microstructure evolution of the deformed Ti-30Zr-5Nb shape memory alloy

The phase transformation and microstructures of the deformed Ti-30Zr-5Nb shape memory alloy were investigated. The X-ray diffraction measurements indicated that the Ti-30Zr-5Nb alloy was composed of a single orthorhombic α″-martensite phase. The alloy exhibited one yielding behavior in the tensile test, with a critical stress of ~ 600 MPa and a tensile strain of approximately 15%. A shape memory recovery accompanied by a permanent strain was exhibited in the deformed alloys when heated at 873 K. The permanent strain increased with increasing pre-strain. The microstructure evolution of the deformed alloy was investigated by transmission electron microscopy. The results showed that the martensite reorientation occurred and the dislocations were generated during deformation. The alloy displayed a reversible martensite transformation start temperature as high as 763 K. However, no strain-induced martensite stabilization was found in the deformed alloy with different pre-strain levels, potentially because the large chemical energy of the Ti-30Zr-5Nb alloy depressed the effects of the elastic energy and the dissipative energy. - Highlights: • Ti-30Zr-5Nb alloy is composed of single orthorhombic α″-martensite phase with M{sub s} of 721 K. • No martensite stabilization has been found in Ti-30Zr-5Nb alloy with different pre-strain. • Ti-30Zr-5Nb shows the maximum shape memory effect of 2.75% with a pre-strain of 8%.

36 MATERIALS SCIENCE↗

Rapid Solidification and Phase Transformations in Additive Manufactured Materials

Within the past few years, additive manufacturing (AM) has emerged as a promising manufacturing technique to enable the production of complex engineering structures with high efficiency and accuracy. Among the important factors establishing AM as a sustainable manufacturing process is the ability to control the microstructures and properties of AM products. In most AM processes, such as laser sintering (LS), laser melting (LM), and laser metal deposition (LMD), rapid solidification and high-temperature phase transformations play primary roles in determining nano- and microstructures, and consequently the mechanical and other properties of AM products. This topic of JOM is dedicated to summarizing the current research efforts in the area of rapid solidification and phase transformations in additively manufactured materials. Finally, a brief summary follows below of 10 journal articles in this topic.

36 MATERIALS SCIENCE↗

Effect of calcination temperature on phase transformation of HfO{sub 2} nanoparticles

Oxides nanomaterials exhibit unique physical, chemical and structural properties and motivated a big research that focus in the integration of these materials for various optoelectronic device applications. In present work, hafnium oxide (HfO{sub 2}) nanoparticles (NPs) have been synthesized using precipitation method. Hafnium tetrachloride and sodium hydroxide has been used as starting precursors. Prepared oxide material has been characterized by X-Ray Diffraction (XRD), Fourier Transform Infra-Red (FTIR) and UV-Vis spectroscopy. The phase transformation from amorphous to monoclinic is observed with the increase in calcination temperature from 500 °C and 800 °C. In FTIR spectra, the characteristic bands at ν ∼ 758.53 and 509.57 cm{sup −1} reveals the monoclinic phase of prepared HfO{sub 2} NPs. UV-Vis spectroscopy shows an absorption peak at 204 nm and the bandgap calculated is 6.07 eV.

36 MATERIALS SCIENCE↗

New Structural Insight into Interface-Controlled α–σ Phase Transformation in Fe-Cr Alloys

Synchrotron Laue microdiffraction scanning is used for the ex situ study of the body-centered, cubic-to-tetragonal phase transformation that occurs in equiatomic polycrystalline Fe-Cr alloys at temperatures between 550 and 800 °C. Grain orientation and grain strains were scanned with a micron step resolution after annealing at 700 °C for 12 h. Further microstructural details on the early stage of the transformation, and more particularly on the cubic-to-tetragonal phase interface, were achieved. Only the α and ordered σ phases were detected. The crystallographic relationships at the interface between the two phases did not follow the predicted rules; this result is discussed in relation to the measured microstrains.

36 MATERIALS SCIENCE↗

Radio-Frequency Rapid Thermal Processing Enabling Spatial Phase Transformation and Nanocrystallization of Soft Magnetic Amorphous Alloys

Thermal processing of soft magnetic amorphous and nanocrystalline alloys is explored under the influence of radio-frequency induction-heating techniques. Direct induction-heating concepts based on longitudinal and transverse flux heating are examined and the details of electromagnetic fields interaction with metallic strips are discussed by analytical calculations as well as finite element analysis. Initial experimental results confirming spatial control of phase transformations and nanocrystallization within a single strip of Finemet Fe-based amorphous ribbons are reported. Here, the degree to which primary and secondary crystallization temperature are achieved depends on the spacing between the ribbon relative to the induction coil as well as the coil design and configuration. For transverse coil configurations, the local temperature and therefore microstructural evolution is different across the lateral dimension of processed ribbons, with reduced gap sizes producing enhanced peak temperatures and larger temperature distributions with greater spatial variation in microstructure. In addition, indirect susceptor-based induction heating under tension is performed and the impact of microstructure is demonstrated. Herein, potential for exploiting spatially optimized phase transformations is illustrated through electromagnetic field–assisted processing in a scalable manufacturing process with amorphous and nanocrystalline soft magnetic alloys.

36 MATERIALS SCIENCE↗

Kinetics study on phase transformation from titania polymorph brookite to rutile

TiO{sub 2} is a polymorphic material of great scientific interest due to its semiconductor properties and uses in heterogeneous photocatalysis. Understanding the stability of the polymorphs is important for designing TiO{sub 2}-based photocatalysts and solar cells. Although the phase transformation of anatase{yields}rutile has been well studied, there is only one published work on brookite{yields}rutile to date. The brookite{yields}rutile transformation has been studied in this work using natural material from the Magnet Cove igneous complex mechanically processed to several micrometers in size. The pure phase brookite is annealed from 800 to 900 deg. C without detection of the anatase polymorph. The transformation kinetics are described by both the standard first-order model, with an activation energy of E{sub a}=411.91 kJ/mol, and the Johnson-Mehl-Avrami-Kolmogorov (JMAK) model, with an activation energy of E{sub a}=492.13 kJ/mol. The rate parameter of the first-order model for the phase transformation is expressed as k=6.85x10{sup 14} exp(-49,451/T) s{sup -1} for the first-order model and k=4.19x10{sup 18} exp(-59,189/T) s{sup -1} using the JMAK model. The obtained activation energy is higher than that of brookite nano-crystals. Our results show that the JMAK model fits the kinetics data better than other models. - Graphical abstract: The transformation kinetics from titania brookite to rutile can be described by both the standard first-order model and the JMAK model. The obtained activation energy for micron-sized brookite crystals is much higher than that for brookite nano-crystals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Raman spectroscopic characterization of SiO 2 phase transformation and Si substrate stress relevant to EBC performance

To accurately model the long-term durability of environmental barrier coatings (EBCs), a more complete understanding of the phase composition and transformations of the thermally grown oxide SiO 2 (TGO) is desired. For the TGO formed during thermal cycling in steam, cristobalite formation and the subsequent β- to α-cristobalite transformation has been identified as a potentially life-limiting mechanism. In this study, Raman micro-spectroscopy was used to quantify the cristobalite transformation on a polycrystalline Si coupon that was exposed to steam at 1350°C for 100 h. The phase transformation was mapped at 200–260°C on the TGO surface at different ramp rates using a heating stage and a micro-positioning stage. The stress in the Si substrate was also determined using Raman spectroscopy by measuring the stress induced peak shift. The α→β phase transformation produced a 300–500 MPa tensile stress in the Si substrate, which compared well to the stress predicted from the volumetric expansion of the cristobalite. In conclusion, quantifying the phase transformation and residual stress are critical tools in developing the next generation of high performance EBCs.

36 MATERIALS SCIENCE↗

Kinetics of moisture-induced phase transformation in inorganic halide perovskite

The high-temperature (high-T) phase of cesium lead iodide (CsPbI 3 ) presents great promise for photovoltaic applications; however, exposure to ambient moisture at room temperature transforms it into its less-desirable low-temperature (low-T) phase with a larger band gap. While there have been theoretical predictions on the influence of moisture level on the phase transformation kinetics, the corresponding quantitative experimental evidence has remained limited. Tracking CsPbI 3 phase transformation under controlled relative humidity (RH), we find that rising RH increases the nucleation rate of low-T CsPbI 3 exponentially, but has a weak effect on its growth. The overall transformation is nucleation limited, with higher RH leading to a lower nucleation barrier. Finally, we find that heating between 40°C and 80°C facilitates water desorption and suppresses phase transformation. Our findings elucidate the relationship between moisture and the phase energetics of CsPbI 3 , which can serve as references for thin film applications of CsPbI 3 and future designs of stable photovoltaics systems.

36 MATERIALS SCIENCE↗