Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PRESSURE RANGE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Oxygen Limit for Flammability of a Gas Mixture of Helium – Hydrogen – Oxygen in the U.S. Department of Energy Standard Canister

The radiolytic breakdown of residual free, physisorbed, and chemisorbed waters is anticipated in the sealed dry storage of spent nuclear fuel (SNF), releasing H 2 gas into the initial cover gas of helium. For aluminum-clad SNF (ASNF) in particular, the expected total hydrogen in the canister is enough to dominate the cover gas mixture if fully released, and based on experimental rates of H 2 generation, H 2 percentages exceeding the lower flammability limit appear likely. However, no evidence of radiolytic generation of O 2 has been observed to date, so the potential for flammability is averted due to the lack O 2 . Lack of oxygen has been credited for avoiding flammability in some existing storage and transportation approaches for SNF and other waste. This report reviews literature on flammability limits with a focus on the limiting oxygen concentration to provide technical underpinnings to refine a flammability criterion for gas mixtures of helium, hydrogen, and oxygen where the oxygen is expected to be the limiting species. While there is general consensus on H 2 flammability limits at standard temperature and pressure, the decay heat and gas generation within ASNF sealed dry storage canisters could push them to elevated temperatures and pressures, so the goal is to identify an oxygen threshold that will bound the behavior over the temperature and pressure range of the U.S. Department of Energy (DOE) Standard Canister. The information reviewed in this document supports the criterion that the oxygen concentration in a He-H 2 -O 2 mixture should be less than 1.5% to avoid flammability at temperatures and pressures relevant to sealed dry storage of ASNF in the DOE Standard Canister, i.e., up to 343°C (650°F) and 500 psig, respectively. Note that while data covering the full range of temperature at atmospheric pressure and nearly the full range of pressure at room temperature were available, data for the combined effects was available only at moderate temperatures and pressures; the recommended 1.5% O 2 threshold is based on the breadth of available data reported here and apparent trends therein.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Intense backward Raman lasers in CH4 and H2

The conversion efficiency of the first Stokes radiation generated by backward stimulated Raman scattering is measured in CH4 and H2 that are pumped by a third harmonic of a Nd:YAG laser in the 12-55-mJ energy range and in the 0.86-6.00-MPa pressure range. Our experimental results show that CH4 is a better Raman medium than H2 at moderate pressures (a few megapascals) to efficiently generate backward Raman lines.

Sentrayan, Karuppasamy↗

Experimental investigation of convection heat transfer of CO{sub 2} at supercritical pressures in a vertical circular tube

The convection heat transfer characteristics of supercritical CO{sub 2} in a vertical circular tube of 2 mm inner diameter were investigated experimentally for pressures ranging from 78 to 95 bar, inlet temperatures from 25 to 40 C, and inlet Reynolds numbers from 3800 to 20,000. The effects of the heat flux, thermo-physical properties, buoyancy and thermal acceleration on the convection heat transfer were analyzed. The experimental results show that for high inlet Reynolds numbers (e.g. Re = 9000) and high heat fluxes, a significant local deterioration and recovery of the heat transfer was found for upward flows but not for downward flows. Comparison of the experimental data for inlet Reynolds numbers from 3800 to 20,000 with some well-known empirical correlations showed large differences especially when the heat transfer deteriorates and then recovers when the effect of buoyancy is significant. The experimental data was used to develop modified local turbulent Nusselt number correlations for supercritical CO{sub 2} flowing in vertical small circular tubes. (author)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Hydrolysis of CuCl{sub 2} in the Cu-Cl thermochemical cycle for hydrogen production : experimental studies using a spray reactor with an ultrasonic atomizer.

The Cu-Cl thermochemical cycle is being developed as a hydrogen production method. Prior proof-of-concept experimental work has shown that the chemistry is viable while preliminary modeling has shown that the efficiency and cost of hydrogen production have the potential to meet DOE's targets. However, the mechanisms of CuCl{sub 2} hydrolysis, an important step in the Cu-Cl cycle, are not fully understood. Although the stoichiometry of the hydrolysis reaction, 2CuCl{sub 2} + H{sub 2}O {leftrightarrow} Cu{sub 2}OCl{sub 2} + 2HCl, indicates a necessary steam-to-CuCl{sub 2} molar ratio of 0.5, a ratio as high as 23 has been typically required to obtain near 100% conversion of the CuCl{sub 2} to the desired products at atmospheric pressure. It is highly desirable to conduct this reaction with less excess steam to improve the process efficiency. Per Le Chatelier's Principle and according to the available equilibrium-based model, the needed amount of steam can be decreased by conducting the hydrolysis reaction at a reduced pressure. In the present work, the experimental setup was modified to allow CuCl{sub 2} hydrolysis in the pressure range of 0.4-1 atm. Chemical and XRD analyses of the product compositions revealed the optimal steam-to-CuCl{sub 2} molar ratio to be 20-23 at 1 atm pressure. The experiments at 0.4 atm and 0.7 atm showed that it is possible to lower the steam-to-CuCl{sub 2} molar ratio to 15, while still obtaining good yields of the desired products. An important effect of running the reaction at reduced pressure is the significant decrease of CuCl concentration in the solid products, which was not predicted by prior modeling. Possible explanations based on kinetics and residence times are suggested.

08 HYDROGEN↗

Influence of Pressure on Physical Property of Ammonia Borane and its Re-hydrogenation

The project systematically studied the high pressure behavior of ammonia borane and its derivative lithium amidoborane. Phase transitions in these materials are investigated in the pressure range up to 20 GPa and temperature range from 80 K to 400K. A number of new phase transitions are discovered in this pressure and temperature range including a second order transformation at 5 GPa and a first order transformation at 12 GPa at room temperature, and four new transitions at high pressure and low temperatures. The Clapeyron slopes for both pressure-induce tetragonal (I4mm) phase to orthorhombic (Cmc21) phase and temperature-induce tetragonal (I4mm) phase to orthorhombic (Pmn21) phase are determined to be positive, indicating these phase transitions are exothermic. This result demonstrates that the high pressure orthorhombic phase of ammonia borane has lower enthalpy than that of tetragonal phase at ambient conditions. If we assume decomposition from the orthorhombic phase yields the same products as that from the tetragonal phase, the decomposition of the orthorhombic phase will be less exothermic. Therefore rehydrogenation from the decomposed product into the orthorhombic phase at high pressure may become easier. The project also studied the influences of nanoconfinement on the phase transitions. Comparative study using Raman spectroscopy indicates that the temperature induced I4mm to Pmn21 transition is suppressed from 217 K to 195 K when the sample is confined in SBA15 (7-9 nm pore size). When the pore size is reduced from 7-9 nm to 3-4 nm, this transition is totally suppressed in the temperature down to 80 K. A similar influence of the nanoconfiement on pressure induced phase transitions is also observed using Raman spectroscopy. The phase boundary between the I4mm phase and high pressure Cmc21 phase at ambient temperature shifts from 0.9 GPa to 0.5 GPa; and that between the Cmc21 phase and higher pressure P21 phase shifts from 10.2 GPa to 9.7 GPa.

08 HYDROGEN↗

Generation of Ribbon Electron Beams by Fore-Vacuum Plasma Sources Based on the Discharge with an Extended Hollow Cathode

The paper presents results of investigation into the special features of physics of fore-vacuum plasma sources of ribbon electron beams. The main difficulties encountered in the development of sources of this type are demonstrated. Conditions that allow one to increase the emission current density with simultaneous preservation of high degree of beam current homogeneity are determined. On the basis of the described physical features in the fore-vacuum plasma sources operation, the main directions in the development of the electron sources generating beams in the fore-vacuum pressure range are proposed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

High-Pressure X-ray Diffraction Study of Tungsten Diselenide

Synchrotron X-ray diffraction was used in conjunction with a diamond anvil cell to investigate the properties of a tungsten diselenide (WSe2) sample to 35.8 GPa at room temperature. By fitting the pressure-volume data to the third-order Birch-Murnaghan equation of state, the bulk modulus, K0T, of WSe2 was determined to be 72{+-}1 GPa with its pressure derivative, K{prime}{sub 0T}, being 4.1{+-}0.1. It was also found that the c-direction of the hexagonal structure is significantly more compressible than the a-direction. No phase transformation was clearly observed in the pressure range of our measurements.

43 PARTICLE ACCELERATORS↗

Turbulent flame speeds and NOx kinetics of HHC fuels with contaminants and high dilution levels

This progress report documents the second year of the project, from October 1, 2011 through September 30, 2012. Characterization of the new turbulent flame speed vessel design was completed. Turbulence statistics of three impellers with different geometric features were measured using particle image velocimetry inside a Plexiglas model (~1:1 scale) of a cylindrical flame speed vessel (30.5 cm ID × 35.6 cm L). With four impellers arranged in a central-symmetric configuration, turbulence intensities between 1.2 and 1.7 m/s with negligible mean flow (0.1u´) were attained at the lowest fan speeds. Acceptable ranges for homogeneity and isotropy ratios of the velocity fields were set within a narrow bandwidth near unity (0.9-1.1). Homogeneity ratios were unaffected by changes to the impeller geometry, and the prototype with the higher number of blades caused the flow to become anisotropic. The integral length scale of the flow fields varied between 27 and 20 mm, which correlates well with those typically observed inside a gas turbine combustor. The mechanism to independently vary the intensity level and the integral length scale was established, where turbulence intensity level was dependent on the rotational speed of the fan, and the integral length scale decreased with increasing blade pitch angle. Ignition delay times of H₂/O₂ mixtures highly diluted with Ar and doped with various amounts of N₂O (100, 400, 1600, 3200 ppm) were measured in a shock tube behind reflected shock waves over a wide range of temperatures (940-1675 K). The pressure range investigated during this work (around 1.6, 13, and 30 atm) allows studying the effect of N₂O on hydrogen ignition at pressure conditions that have never been heretofore investigated. Ignition delay times were decreased when N₂O was added to the mixture only for the higher nitrous oxide concentrations, and some changes in the activation energy were also observed at 1.5 and 30 atm. When it occurred, the decrease in the ignition delay time was proportional to the amount of N₂O added and depended on pressure and temperature conditions. A detailed chemical kinetics model was developed using kinetic mechanisms from the literature. This model predicts well the experimental data obtained during this study and from the literature. The chemical analysis using this model showed that the decrease in the ignition delay time was mainly due to the reaction N₂O +M ⇌ N₂ + O +M which provides O atoms to strengthen the channel O + H₂ ⇌ OH + H. Ignition delay times have been measured behind reflected shock waves at 1.5, 12 and 30 atm for a mixture representative of a syngas produced from biomass (0.29659% CO / 0.29659% H₂ / 0.15748% CO₂ / 0.08924% CH₄ / 0.20997% H₂O / 0.95013% O₂ in 98% Ar (mol.%)) and for the same biomass-derived syngas mixture doped with 200 ppm of NH₃. The importance of the various constituents on the ignition delay time was investigated by comparing the results with data from various baseline mixtures (H₂/O₂/Ar, H₂/CO/O₂/Ar and H₂/CO/O₂/Ar with one of the other constituent of the syngas (i.e. CO₂, H₂O, CH₄ or NH₃)). The equivalence ratio was set to 0.5 during this study. Several recent detailed kinetics mechanisms from the literature were computed against these data, with fair agreement. Results showed that the mixture composition can have an important effect on the ignition delay time, with most of the effect being due to CH₄ addition through the reaction CH₄+OH⇌CH₃+H₂O. The ammonia impurity had very little effect on the ignition delay time over the range of conditions studied.

Petersen, Eric↗

Stress State of Diamond and Gold under Nonhydrostatic Compression to 360 GPa

Diamond and gold powders were compressed nonhydrostatically in a diamond anvil cell and examined by x-ray diffraction using a radial geometry to evaluate the evolution of stresses and strains in these materials to ultrahigh pressure. We found that near isostrain continuity developed across diamond and gold grains under uniaxial compression. The observed mean pressure of diamond powder reached to 360(40) GPa while it was only 31(1) GPa for the polycrystalline gold under the highest load. Polycrystalline diamond can support a microscopic deviatoric stress of 160(18) GPa at about 360 GPa. Due to the deformation of the diamond anvil culet, the macroscopic differential stress of the diamond sample was limited to about 43(8) GPa. There is no evidence that the diamond grains have yielded in our experimental pressure range.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Broadening and shift of the spectral lines of hydrogen atoms and silicon ions in laser plasma

We report an experimental investigation of the broadening and shift of discrete lines in the plasma spectrum produced in the laser ablation of silicon in a broad pressure range (10{sup 2} – 10{sup 7} Pa) of the ambient gas (Ar, He, H{sub 2}). The broadening and line shifts are measured in relation to the distance from the target and initial gas pressure. The threshold nature of the resulting dependences is found to be related to the formation of virtual percolation clusters proceeding in the hot dense plasma. (laser plasma)

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Analytical investigation of two hydrogen oxygen rocket engine systems for low-thrust application

Two hydrogen oxygen rocket engine system concepts were analyzed parametrically over a thrust range from 100 to 1000 pounds and a chamber pressure range from 175 to 1000 psia. Both concepts were regeneratively cooled with hydrogen and were pump fed by electric motor driven positive displacement pumps. Electric power was provided by either a turboalternator (turboalternator concept) or some means external to the engine system (auxiliary power concept). The turboalternator concept is discussed. The computer program used to conduct the analyses along with the design characteristics of the major engine system components is described. The feasible design range of the systems over the parametric range of thrust is discussed in terms of allowable chamber pressure. Engine system estimated performance, mass, and dimensional envelope parametric data within the feasible design range are presented.

Scheer, D. D.↗

Coulomb Logarithm in Nonideal and Degenerate Plasmas

Various methods for determining the Coulomb logarithm in the kinetic theory of transport and various variants of the choice of the plasma screening constant, taking into account and disregarding the contribution of the ion component and the boundary value of the electron wavevector are considered. The correlation of ions is taken into account using the Ornstein–Zernike integral equation in the hypernetted-chain approximation. It is found that the effect of ion correlation in a nondegenerate plasma is weak, while in a degenerate plasma, this effect must be taken into account when screening is determined by the electron component alone. The calculated values of the electrical conductivity of a hydrogen plasma are compared with the values determined experimentally in the megabar pressure range. It is shown that the values of the Coulomb logarithm can indeed be smaller than unity. Special experiments are proposed for a more exact determination of the Coulomb logarithm in a magnetic field for extremely high pressures, for which electron scattering by ions prevails.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Addendum to High Pressure Burn Rate Measurements on an Ammonium Perchlorate Propellant

As part of a small follow-on study, the burn rate of the ammonium perchlorate (AP) based material TAL-1503 was studied at a relatively mild pressure. The goal of this final experiment was to burn TAL-1503 at the lowest pressures possible using the LLNL High Pressure Strand Burner (LLNL-HPSB). The following is a description of the experiment and the results with a brief discussion of data and a comparison to the higher pressure data. This is not meant to be a stand-alone report and readers should refer to the main report for experimental details and discussion. High pressure deflagration rate measurements of a unique AP/HTPB based material (TAL-1503) were performed using the LLNL high pressure strand burner apparatus. The material burns in a well behaved, laminar fashion between 20 and 300 MPa with a burn law of B = (0.6 {+-} 0.1) x P{sup (1.05{+-}0.02)} that was calculated based on the best data available from the experiments. In the pressure range of 2 and 10 MPa the material burned laminarly with a burn law of B = (2.0 {+-} 0.2) x P{sup (0.66{+-}0.05)}. In these results, B is the burn rate in mm/s and P is the pressure in units of MPa. Comparison of the TAL-1503 results with similar propellants that contain micrometer sized aluminum indicate that the burn rates are relatively unaffected by the aluminum. However, the pressure change is significantly larger when aluminum is present, most likely due to the high temperatures achieved from burning aluminum.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Structure and reactivity of iridium oxide layers grown on Ir(1 0 0) by oxidation at sub-ambient O 2 pressures

We used low energy electron diffraction (LEED) and temperature programmed desorption (TPD) to investigate the structure and reactivity of iridium oxide layers prepared by oxidizing Ir(100) at 765 K and O 2 pressures ranging from 0.05 to 5 Torr. Our LEED results provide evidence that Ir(100) oxidation at O 2 pressures up to 0.20 Torr produces a mixture of Ir oxide structures present as small domains, including a commensurate IrO 2 (101) structure that coexists with other structures. Oxidizing from 0.50 to 1 Torr causes formation of a commensurate IrO 2 (110)R27° structure and a sharp rise in the oxygen uptake from ~8 to 20 ML (monolayer) as the films exhibit signs of roughening. Further increasing the O 2 pressure from 1 to 5 Torr causes the IrO 2 (110)R27° structure to be replaced with a so-called IrO 2 (110)-aligned structure, for which the IrO 2 (110) lattice vectors align with those of the Ir(100) substrate. We find that the oxidized Ir(100) surfaces become increasingly reactive toward the dissociation and oxidation of CH 4 as IrO 2 (110) develops on the surface, and observe that the IrO 2 (110)-aligned structure is more reactive than the IrO 2 (110)R27° phase. Furthermore, our findings demonstrate that the oxide phase evolution on Ir(100) is sensitive to the O 2 pressure in the range from 0.05 to 5 Torr, and that the development of reactive IrO 2 (110) structures requires elevated O 2 pressures (> 0.5 Torr) and temperature.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A high pressure, high temperature study of 1,1-diamino-2,2-dinitro ethylene

We report a synchrotron energy-dispersive X-ray diffraction study of the novel high explosive 1,1-diamino-2,2-dinitroethylene at high pressures and high temperatures. Pressure was generated using a Paris-Edinburgh cell to employ larger sample volumes. High temperatures were created using a resistive graphite cylinder surrounding the sample. The PT phase diagram was explored in the 3.3 GPa pressure range and in the {approx} 400 C temperature range. We believe that the sample commenced in the {alpha}-phase and then ended up in an amorphous phase when the temperature increased beyond 280 C near 2 GPa, which we believe to be the {gamma}-phase. Further pressure and temperature cycling suggests that the sample transformed reversibly into and out of the amorphous phase near the phase line.

99 GENERAL AND MISCELLANEOUS↗

MICROSTRUCTURE AND MECHANICAL PROPERTY PERFORMANCE OF COMMERCIAL GRADE API PIPELINE STEELS IN HIGH PRESSURE GASEOUS HYDROGEN

The continued growth of the world s developing countries has placed an ever increasing demand on traditional fossil fuel energy sources. This development has lead to increasing research and development of alternative energy sources. Hydrogen gas is one of the potential alternative energy sources under development. Currently the most economical method of transporting large quantities of hydrogen gas is through steel pipelines. It is well known that hydrogen embrittlement has the potential to degrade steel s mechanical properties when hydrogen migrates into the steel matrix. Consequently, the current pipeline infrastructure used in hydrogen transport is typically operated in a conservative fashion. This operational practice is not conducive to economical movement of significant volumes of hydrogen gas as an alternative to fossil fuels. The degradation of the mechanical properties of steels in hydrogen service is known to depend on the microstructure of the steel. Understanding the levels of mechanical property degradation of a given microstructure when exposed to hydrogen gas under pressure can be used to evaluate the suitability of the existing pipeline infrastructure for hydrogen service and guide alloy and microstructure design for new hydrogen pipeline infrastructure. To this end, the 2 Copyright 2010 by ASME microstructures of relevant steels and their mechanical properties in relevant gaseous hydrogen environments must be fully characterized to establish suitability for transporting hydrogen. A project to evaluate four commercially available pipeline steels alloy/microstructure performance in the presences of gaseous hydrogen has been funded by the US Department of Energy along with the private sector. The microstructures of four pipeline steels were characterized and then tensile testing was conducted in gaseous hydrogen and helium at pressures of 800, 1600 and 3000 psi. Based on measurements of reduction of area, two of the four steels that performed the best across the pressure range were selected for evaluation of fracture and fatigue performance in gaseous hydrogen at 800 and 3000 psi. This paper will describe the work performed on four commercially available pipeline steels in the presence of gaseous hydrogen at pressures relevant for transport in pipelines. Microstructures and mechanical property performances will be compared. In addition, recommendations for future work related to gaining a better understanding of steel pipeline performance in hydrogen service will be discussed.

08 HYDROGEN↗

Wireless Capacitive Pressure Sensor With Directional RF Chip Antenna for High Temperature Environments

This paper presents the design, fabrication and characterization of a wireless capacitive pressure sensor with directional RF chip antenna that is envisioned for the health monitoring of aircraft engines operating in harsh environments. The sensing system is characterized from room temperature (25 C) to 300 C for a pressure range from 0 to 100 psi. The wireless pressure system consists of a Clapp-type oscillator design with a capacitive MEMS pressure sensor located in the LC-tank circuit of the oscillator. Therefore, as the pressure of the aircraft engine changes, so does the output resonant frequency of the sensing system. A chip antenna is integrated to transmit the system output to a receive antenna 10 m away.The design frequency of the wireless pressure sensor is 127 MHz and a 2 increase in resonant frequency over the temperature range of 25 to 300 C from 0 to 100 psi is observed. The phase noise is less than minus 30 dBcHz at the 1 kHz offset and decreases to less than minus 80 dBcHz at 10 kHz over the entire temperature range. The RF radiation patterns for two cuts of the wireless system have been measured and show that the system is highly directional and the MEMS pressure sensor is extremely linear from 0 to 100 psi.

Pressure sensor↗