Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PLATES, STRUCTURAL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Evolution of microstructure and strength of a high entropy alloy undergoing the strain-induced martensitic transformation

In a recent work, we have reported outstanding strength and work hardening exhibited by a metastable high entropy alloy (HEA), Fe 42 Mn 28 Co 10 Cr 15 Si 5 (in at. %), undergoing the strain-induced martensitic transformation from metastable gamma austenite (γ) to stable epsilon martensite (ε). However, the alloy exhibited poor ductility, which was attributed to the presence of the brittle sigma (σ) phase in its microstructure. The present work reports the evolution of microstructure, strength, and ductility of a similar HEA, Fe 38.5 Mn 20 Co 20 Cr 15 Si 5 Cu 1.5 (in at. %), designed to suppress the formation of σ phase. A cast and then rolled plate of the alloy was processed into four conditions by annealing for 10 and 30 min at 1100 °C and by friction stir processing (FSP) at tool rotation rates of 150 and 400 revolutions per minute (RPM) to facilitate detailed examinations of variable initial grain structures. Neutron diffraction and electron microscopy were employed to characterize the microstructure and texture evolution. The initial materials had variable grain size but nearly 100% γ structure. Diffusionless strain induced γ→ε phase transformation took place under compression with higher rate initially and slower rate at the later stages of deformation, independent on the initial grain size. The transformation facilitated part of plastic strain accommodation and rapid strain hardening owing to a transformation-induced dynamic Hall-Petch-type barrier effect, increase in dislocation density, and texture. Here, the peak strength of nearly 2 GPa was achieved under compression using the structure created by double pass FSP (150 RPM followed by 150 RPM). Remarkably, the tensile elongation exhibited by the alloy was nearly 20% with fracture surfaces featuring a combination of ductile dimples and cleavage.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Sodium trithiocarbonate cathode for high-performance sodium–sulfur batteries

The high abundance and low cost of sodium and sulfur make room-temperature sodium-sulfur (RT Na-S) batteries an attractive technology compared to the current lithium-ion batteries for large-scale grid-storage applications. However, the commercialization of RT Na-S batteries is impeded by the slow kinetics of Na-S chemistry, severe sodium polysulfide shuttling, and uncontrollable growth of dendritic Na. Herein, sodium trithiocarbonate (Na 2 CS 3 ) is applied as a cathode material to facilitate concurrent improvement in both electrodes, leading to a high-rate performance with extended cycle life. The conductive characteristic of the carbon-sulfur resonance bond provides fast ion and electron transfer throughout the cathode, resulting in superior electrochemical reactivity. At the cathode, the presence of Na2CS3 forms an oligomer-structured layer to suppress the dissolution and shuttling of active materials. Meanwhile, when small portions of Na 2 CS 3 intermediates migrate to the anode, a stable solid electrolyte interphase (SEI) layer with uniform Na-ion flux is formed, enabling improved Na stripping and plating performance. A series of electrochemical and materials characterization, accompanied by density functional theory calculations demonstrate that Na 2 CS 3 is a promising candidate to realize high-rate performance long cycle life RT Na-S batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

Report on FY 2023 Experimental Results in Developing the Fabrication Parameters for Alloy 709 in Different Product Forms

The Advanced Reactor Technologies (ART) Program has established a multi-year plan to develop Alloy 709 advanced stainless steel (A709), generate the data package and develop material-specific design parameters in qualifying it as a new structural material for Class A construction in the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section III, Division 5, High Temperature Reactors (ASME 2023). In collaboration with material vendors, the Advanced Materials Development activities under ART have successfully scaled the A709 plate form production from a laboratory heat of 500 pounds to commercial heats totaling 133,000 pounds of A709 plate fabricated from three heats. The goal of the overall A709 development program is to establish the necessary microstructural and mechanical properties relationship for A709 to ultimately develop fabrication parameters for other product forms such as bars, pipes, and forgings using the available ART A709 materials. The objective of this A709 development work in FY 2023 is to experimentally determine grain coarsening behavior for the A709 heats and to experimentally generate the continuous cooling precipitation (CCP) diagram for A709 using the as-rolled commercial heat plate materials. Integral to this work is the characterization of the as-rolled materials and the determination of an effective solution-annealing process, which was reported in Y. Wang et al., 2023. This report summarizes the results of the high-speed dilatometry project to develop the CCP diagram using the commercial heat 58776-3RB fabricated by G. O. Carlson and heat 529900-02 fabricated by Allegheny Technologies Incorporated (ATI) Specialty Rolled Products.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

Chemical and Structural Insights into Solid Electrolyte Interphase Evolution for Sodium Metal Electrodes

The solid electrolyte interphase (SEI) critically governs the reversibility of sodium metal batteries, through dynamically mediating ion transport and interfacial reactions. However, its kinetic evolution under operating conditions, and how it influences interfacial stability, remains poorly understood. Here, in this study, we reveal that the SEI undergoes coupled chemical and mechanical changes during sodium plating and stripping, leading to spatial and temporal heterogeneity that drives interfacial degradation. Synchrotron operando grazing-incidence wide-angle X-ray scattering and soft X-ray absorption spectroscopy capture the sequential formation and dissolution of inorganic SEI phases (NaF, NaH, NaOH, Na 2 PO 3 F), accompanied by depth-dependent alterations in organic SEI components. Mesoscale modeling connects this evolving SEI heterogeneity to localized current density fluctuations and stress accumulation at the Na interface, identifying pathways to electrically isolated sodium formation. These findings show that SEI instability fundamentally limits reversibility in sodium metal batteries, and that controlling SEI chemistry–mechanics coupling is essential to achieving its durability.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Microscopic Manipulation of Ferroelectric Domains in SnSe Monolayers at Room Temperature

Two-dimensional (2D) van der Waals ferroelectrics provide an unprecedented architectural freedom for the creation of artificial multiferroics and nonvolatile electronic devices based on vertical and coplanar heterojunctions of 2D ferroic materials. Nevertheless, controlled microscopic manipulation of ferroelectric domains is still rare in monolayer-thick 2D ferroelectrics with in-plane polarization. Here we report the discovery of robust ferroelectricity with a critical temperature close to 400 K in SnSe monolayer plates grown on graphene and the demonstration of controlled room-temperature ferroelectric domain manipulation by applying appropriate bias voltage pulses to the tip of a scanning tunneling microscope (STM). This study shows that STM is a powerful tool for detecting and manipulating the microscopic domain structures in 2D ferroelectric monolayers, which are difficult for conventional approaches such as piezoresponse force microscopy, thus facilitating the hunt for other 2D ferroelectric monolayers with in-plane polarization with important technological applications.

2D ferroelectric↗
DOE OSTI2021

Wood Carbon Based Single-Atom Catalyst for Rechargeable Zn–Air Batteries

Low-cost and efficient oxygen reduction reaction (ORR)/oxygen evolution reaction (OER) bifunctional electrocatalysts are vital for the applications of rechargeable Zn-air batteries (ZABs). Given the high catalytic activity of single-atom catalysts (SACs), preparing SACs on a large scale for ZABs is desirable but remains challenging. Herein, in situ formation of single-atom Fe-N-C catalysts on plate wood-based porous carbon is achieved via a facile Lewis acid pretreatment and carbonization process. Lewis acid FeCl3 pretreatment on the cell wall of wood not only produces abundant microchannels but also successfully introduces atomically dispersed Fe-N active species into the hierarchical structure. Such uniformly dispersive SACs on the hierarchical structure enhance the ORR/OER performance and durability. A ZAB using the catalyst in the cathode shows a high power density (70.2 mW cm -2 , at quasi solid state) and long-term stability. This work provides a new path for the large-scale preparation of high-performance SACs.

25 ENERGY STORAGE↗
DOE OSTI2025

Monofluorinated acetal electrolyte for high-performance lithium metal batteries

High degree of fluorination for ether electrolytes has resulted in improved cycling stability of lithium metal batteries due to stable solid electrolyte interphase (SEI) formation and good oxidative stability. However, the sluggish ion transport and environmental concerns of high fluorination degree drive the need to develop less fluorinated structures. Here, we depart from the traditional ether backbone and introduce bis(2-fluoroethoxy)methane (F2DEM), featuring monofluorination of the acetal backbone. High coulombic efficiency and stable long-term cycling in Li||Cu half cells can be achieved with F2DEM even under fast Li metal plating conditions. The performance of F2DEM is further compared with diethoxymethane (DEM) and 2-[2-(2,2-difluoroethoxy)ethoxy]-1,1,1-trifluoroethane (F5DEE). A significantly lower overpotential is observed with F2DEM, which improves energy efficiency and enables its application in high-rate conditions. Comparative studies of F2DEM with DEM and F5DEE in anode-free lithium iron phosphate (LiFePO4) LFP pouch cells and high-loading LFP coin cells further show improved capacity retention of F2DEM electrolyte, demonstrating its practical applicability. More importantly, we also extensively investigate the underlying mechanism for the superior performance of F2DEM through various techniques, including X-ray photoelectron spectroscopy, scanning electron microscopy, cryogenic electron microscopy, focused ion beam, electrochemical impedance spectroscopy, and titration gas chromatography. Overall, F2DEM facilitates improved Li deposition morphology with reduced amount of dead Li. This enables F2DEM to show superior performance, especially under higher charging and slower discharging rate conditions.

25 ENERGY STORAGE↗
DOE OSTI2026

Towards Thermomechanical Processing of Alloy 709: Progress in Defining High-Temperature Deformation-Recrystallization "Space"

The Advanced Reactor Technologies (ART) Program has established a multi-year plan to develop Alloy 709 advanced stainless steel, generate the data package and develop material-specific design parameters in qualifying it as a new structural material for Class A construction in the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section III, Division 5, High Temperature Reactors (ASME 2025). In collaboration with material vendors, the Advanced Materials Development activities under ART have successfully scaled the Alloy 709 plate form production from a laboratory heat of 500 pounds to commercial heats totaling 133,000 pounds of Alloy 709 plate fabricated from three heats. The goal of the overall Alloy 709 development program is to establish the necessary microstructural and mechanical properties relationship for Alloy 709 to ultimately develop fabrication parameters for other product forms such as bars, pipes, and forgings using the available ART Alloy 709 materials. This study will enable its deployment in the industry as an advanced construction material for high-temperature components. The objective of this Alloy 709 development work in FY 2025 is to experimentally determine the high-temperature deformation-recrystallization response of the Alloy 709 heats and to experimentally generate true stress-true strain data for Alloy 709 using the available commercial heat plate materials. Integral to this work is the previous characterization of the as-rolled materials and the determination of an effective solution-annealing process, which was reported in Y. Wang et al., 2023, and the evaluation of the effect of controlled cooling on the resultant precipitation in these commercial heats. This report summarizes and builds on the results of the previous reports to assess the high-temperature deformation behavior as a function of deformation temperature, strain and strain rate using commercial Alloy 709 heat 58776-3RB fabricated by G. O. Carlson and heat 529900-02 fabricated by Allegheny Technologies Incorporated (ATI) Specialty Rolled Products.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Self-seeded growth of very large open-structured zeolite nanosheet assemblies with extraordinary micropore accessibility

Zeolite nanosheets (ZNs) offer improved micropore accessibilities and transport properties for enhanced molecular catalysis and separations. However, practical application of the ZN materials is hampered by the lack of efficient synthesis methods. Here, in this work, a ZN self-seeded method is demonstrated for single-step reproduction of flower-like assemblies of very large MFI ZN plates. The ZN plates are ~60 nm-thick stacks of 4-nm-thick single-crystal sheets. The ZN flower growth involves terrace nucleation on the seed surfaces and subsequent ZN epitaxial growth in [010] orientation directed by a diquaternary agent. The open architecture of the assemblies prevented collapse and agglomeration of ZNs during thermal activation that effectively preserved the interconnected intra-sheet and inter-sheet micropore system. Thus, the ZN assemblies exhibited markedly enhanced molecular adsorption capacity and transport diffusivity for the probing xylene molecules as compared to the conventional crystals. The ZN assembly and its harvestable very large-sized ZNs have the potential for developing high-performance ZN adsorbents, catalysts, and molecular-sieve membranes.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Emissions and Flame Structure Assessment of Aeroengine Micromixing Injectors for Lean Direct Injection of Hydrogen and Hydrogen/Natural Gas Blends

Abstract The present study focuses on whether adapting low emissions liquid fuel injection concepts can be applied to gaseous mixtures. The goal is to develop an injector with specific geometric characteristics that will achieve the lowest emissions. This is conducted by evaluating emissions and flame diagnostics on a set of test hardware that has been developed for combustion of pure hydrogen and hydrogen/methane mixtures. The current test hardware adapts lean direct injection concepts from aeroengine injectors to a ground-based engine based on target flows associated with a Solar Turbines Industrial Engine gas turbine. A statistical test plan was developed to assess these geometric characteristics using a three level Box Behnken design. The test plan investigates the effect of injector flow splits, air swirl, fuel swirl, pressure drop, preheat temperature, fuel composition, and the adiabatic flame temperature on the flame structure and emissions performance. A total of 16 injectors were considered for a total of 688 test points for emission and imaging data. Emissions data were reported on a mass basis in ng/J and chemical reactor network analysis were conducted to further interpret emissions behavior. Images were also captured to analyze the flame structure features of interest including reaction volume, flame length, flame spread, and flame width. With these results, a predictive model for emissions was made to conclude the most optimal injector configuration is to have the highest level of air split (more volume of air through the injector plate versus the injector) and air swirl angle for both methane and hydrogen gas mixtures. The predictive emissions level for all of these cases were below 10 ng/J.

08 HYDROGEN↗
DOE OSTI2021

A high temperature cell for investigating interfacial structure on the molecular scale in molten salt/alloy systems

In this work, we describe the design and development of an in situ neutron reflectometry cell for high temperature investigations of structural changes occurring at the interface between inorganic salts, in their molten state up to 800 °C, and corrosion resistant alloys or other surfaces. In the cell, a molten salt is confined by an annular ring of single crystal sapphire constrained between the sample substrate and a sapphire plate using two gold O-rings, enclosing a liquid salt volume of 20 ml, along with a dynamic cell volume to accommodate expansion of the liquid with heating. Further, as a test case for the cell, we report on an in situ neutron reflectometry measurement of the interface between a eutectic salt mixture of MgCl 2 –KCl (32:68 molar ratio) and a single crystal sapphire substrate at 450 °C, resulting in the formation of a 60 Å layer having a scattering length density of 1.72 × 10 –6 Å –2 . While the origin of this layer is uncertain, it is likely to have resulted from the salt reacting with an existing impurity layer on the sapphire substrate.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2021

Efficient Lithium Metal Cycling over a Wide Range of Pressures from an Anion-Derived Solid-Electrolyte Interphase Framework

Advanced electrolytes were developed to improve the cyclability of lithium (Li) metal anodes, yet their working mechanisms remain unclear. Here, we study the Li cycling performance under different pressures in a 1 M Li bis(fluorosulfonyl)imide/fluorinated 1,4-dimethoxybutane electrolyte. A consistently long cycle life is achieved over a wide range of pressures (30–600 psi). We find that this is due to a completely different Li plating mode with more favorable deposition morphologies compared to that in a conventional carbonate electrolyte, which exhibits increasing cycle stability with increased pressure. We show that this is enabled by the properties of an anion-derived residual solid-electrolyte interphase (rSEI) framework on the electrode surface, an undercharacterized structure with profound implications for Li metal cycling. This anion-derived rSEI chemistry is likely the key to a prolonged cycle life of Li metal batteries and should be vigorously addressed in future electrolyte designs.

25 ENERGY STORAGE↗
DOE OSTI2022

Material Characterization of Grade 91 Steel Welds using, Micro-resolution Ultrasonic Imaging System

Grade 91 (9Cr-1Mo-V) steel is a common structural material for fossil-fuel fired and nuclear power plants because of its creep strength and oxidation resistance at high temperatures. In this research, we studied the feasibility of correlating the high-resolution images obtained from the immersion ultrasonic imaging technique to microstructure regions in Grade 91 steel plate weldments. The high-resolution ultrasonic images presented in this paper were generated using a 20-MHz focused transducer as the transmitter, and a laser vibrometer as the receiver in the through transmission configuration to produce longitudinal and shear waves. This nondestructive evaluation (NDE) method was used to identify the Fusion Zone (FZ), Heat-Affected Zone (HAZ), and Base Metal (BM) regions of Grade 91 cold metal transfer (CMT) and flux core arc welds (FCAW). The ultrasonic imaging results were analyzed using beam propagation amplitudes and homogeneity, which in turn were used to relate the different microstructure regions of the FCAW and CMT welded samples. With this study, we were able to identify highly susceptible microstructures in the weld that could potentially promote creep type failures.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2023

Multidimensional Diagnostics of the Interface Evolutions in Solid-State Lithium Batteries

All-solid-state lithium metal batteries hold tremendous potential as next-generation energy storage solutions. However, their performance is hindered by complex chemo-mechanical instabilities at the interface, which encompass electrolyte decomposition, loss of contact due to volume changes, and the growth of lithium filaments. Given the complexity of these failure mechanisms, it is imperative to employ multidimensional diagnostics that leverage a combination of tools capable of quantifying formed voids and filaments, identifying the chemical and mechanical properties of lithium dendrites and electrolyte decomposition products, as well as monitoring the evolution of these processes in situ. The primary objective of this project is to develop a comprehensive characterization platform for solid-state battery interfaces, integrating FIB-SEM tomography, ToF-SIMS, in-SEM nanoindentation, and in-SIMS AFM-based stiffness mapping to enable structural, chemical, and mechanical analyses. The project team has accomplished significant milestones, including: 1) The successful development of a characterization platform that combines FIB-SEM, ToF-SIMS, nanoindentation, and AFM. 2) The creation of solid-state cells at various scales. 3) Real-time visualization of the plating and stripping of lithium. 4) Operando analysis of the chemical composition and evolution of electrolyte decomposition products, encompassing intermediate and metastable species, at both the cathode and anode interfaces. 5) In situ analysis of mechanical properties coupled with chemical mapping. 6) The implementation of the multiscale characterization technique has yielded valuable insights into cell failure mechanisms and has led to the development of a solid-state lithium cell that exhibits exceptional durability, surpassing 2500 cycles. This project has resulted in 10 publications, 1 invention disclosure, 8 manuscripts under review or in preparation.

25 ENERGY STORAGE↗
DOE OSTI2024

Chasing the multi-modal plasma response in MAST-U

Abstract Achieving edge localized modes (ELMs) suppression in spherical tokamaks by applying resonant magnetic perturbations (RMPs) has proven challenging. The poloidal spectrum of the applied RMP is a key parameter that has an impact on the capability to mitigate and eventually suppress ELMs. In this work the resistive magnetohydrodynamic code MARS-F (Liu et al 2000 Phys. Plasmas 7 3681) is used to evaluate the possibility of directly measuring the plasma response in MAST-U, and particularly its variation as function of the applied poloidal spectrum, in order to guide the experimental validation of the predicted best RMP configuration for ELM suppression. Toroidal mode number n = 2 RMP is considered to minimize the presence of sidebands, and to avoid the deleterious core coupling of n = 1. Singular Value Decomposition is used to highlight linearly independent structures in the simulated magnetic 3D fields and how those structures can be measured at the wall where the magnetic sensors are located. Alternative ways to measure the multimodal plasma response and how they can be used to infer the best RMP configuration to achieve ELM suppression are also presented, including the plasma displacement and the 3D footprints at the divertor plates.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

In Situ Prediction of Microstructure and Mechanical Properties in Laser-Remelted Al-Si Alloys: Towards Enhanced Additive Manufacturing

Laser surface remelting of aluminum alloys has emerged as a promising technique to enhance mechanical properties through refined microstructures. This process involves rapid cooling rates ranging from 10 3 to 10 8 °C/s, which increase solid solubility within aluminum alloys, shifting their eutectic composition to a larger value of silicon content. Consequently, the resulting microstructure combines a strengthened aluminum matrix with silicon fibers. This study focuses on the laser scanning of Al-Si aluminum alloy to reduce the size of aluminum matrix spacings and transform fibrous silicon particles from micrometer to nanometer dimensions. Analysis revealed that the eutectic structure contained 17.55% silicon by weight, surpassing the equilibrium eutectic composition of 12.6% silicon. Microstructure dimensions within the molten zones, termed ‘melt pools’, were extensively examined using Scanning Electron Microscopy (SEM) at intervals of approximately 20 μm from the surface. A notable increase in hardness, exceeding 50% compared to the base plate, was observed in the melt pool regions. Thus, it is exemplified that laser surface remelting introduces a novel strengthening mechanism in the alloy. Moreover, this study develops an in situ method for predicting melt pool properties and dimensions. A predictive model is proposed, correlating energy density and spectral signals emitted during laser remelting with mechanical properties and melt pool dimensions. This method significantly reduces characterization time from days to seconds, offering a streamlined approach for future studies in additive manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Phase Stability and Kinetics of Topotactic Dual Ca 2+ –Na + Ion Electrochemistry in NaSICON NaV 2 (PO 4 ) 3

Recent reports of reversible calcium plating and stripping have rekindled interest in the development of Ca-ion batteries (CIBs) as next-generation energy storage devices. This technology has the potential to overcome the limitations of conventional Li-ion batteries, but CIBs are plagued by a paucity of suitable cathode materials. To date, NaSICON-structured NaV 2 (PO 4 ) 3 has been demonstrated as a successful cathode candidate, exhibiting reversible (de)intercalation of 0.6 mol Ca 2+ along with stable cycling performance. However, a complex multiphase mixture forms on discharge so the Ca-ion charge storage mechanism in the NaSICON framework is poorly understood. Here in this work, we report on an investigation of the structure and/or Na + /Ca 2+ environment(s) of a variety of chemically prepared NaSICON Ca x Na y V 2 (PO 4 ) 3 phases which were characterized using synchrotron XRD, SEM-EDS, 23 Na NMR, and TEM. Highly calciated CaV 2 (PO 4 ) 3 , Ca 1.5 V 2 (PO 4 ) 3 , and CaNaV 2 (PO 4 ) 3 phases can be prepared at high temperature, but -unlike Ca 0.6 NaV 2 (PO 4 ) 3 -these materials are electrochemically inactive. To better understand the fundamental factors impacting successful Ca 2+ electrochemistry in this system, DFT was employed to examine the Ca x Na y V 2 (PO 4 ) 3 phase diagram and Ca 2+ diffusion mechanism. Theoretical insights show that phase separation into Na-rich and Ca-rich phases is a reason for the capacity limitation and demonstrate that Na + ions in the host materials assist the migration of neighboring Ca 2+ ions, enabling reversible electrochemistry in Ca x Na y V 2 (PO 4 ) 3 . This investigation of fundamental principles affecting reversible Ca 2+ (de)intercalation in Ca x Na y V 2 (PO 4 ) 3 allows for the development of design principles to enable the discovery of a variety of successful cathodes for CIBs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Boundary Layer Climatology at ARM Southern Great Plains

Operational since 1992, the Atmospheric Radiation Measurement (ARM) southern great plains (SGP) site at Oklahoma, USA has become a reference research site for meteorological studies. Due to an open data policy the ARM data are used by researchers all over the world. In this report, we review the long-term climatology of the atmospheric boundary layer, SGP instrumentations, the site and some site-specific atmospheric conditions which potentially effect wind turbines within the region. As the atmospheric boundary layer is bounded and influenced by the surface, observations of surface radiation components and heat fluxes are crucial in understanding land-atmosphere interactions. The entrainment of air, updrafts, downdrafts and boundary layer height characteristics is needed for understanding the structure and growth of the atmospheric boundary layer. Therefore, measurements from both surface in-situ and remote sensing observations at SGP provide an overall climatology and their interactions from surface up to the boundary layer. Measurements from a 60 m meteorological tower, surface flux stations, disdrometers, soil temperature and moisture flux plates, coherent Doppler lidar, Raman lidar, radiosondes, and satellite data at SGP central facility were analyzed. All the measurements were generally within a few square kilometers of each other at the central facility. This report focuses on data from January 2010 to June 2020 at SGP central facility. The various sections describe the ARM SGP site and surrounding wind turbines; in-situ and remote sensing instrumentation used in the report; provides mathematical equations to analyze fluxes, turbulence and other boundary layer parameters; a climatological analysis of surface winds, fluxes and thermodynamic parameters for several years; an analysis of observed winds in the framework of Monin-Obukhov Similarity Theory; an analysis of the boundary layer winds and direction from a Doppler lidar; multi-year turbulence estimates through the boundary layer from a Doppler lidar; atmospheric boundary layer water vapor and relative humidity profiles from Raman lidar; cloud base height and boundary layer height from multiple sensors and satellite data; and finally site specific atmospheric conditions, such as nocturnal low-level jets. Diurnal, seasonal and yearly variations of surface, sub-surface and boundary layer quantities, such as wind speed, direction, temperature, atmospheric stability, soil temperature, and various atmospheric fluxes at SGP showed distinct trends useful for focused modeling studies. The applicability of surface similarity theory on ARM SGP data is also evaluated, which showed northerly flows are aligned with MO theory estimates compared to southerly flows. Boundary layer winds and direction profiles for several years from a Doppler lidar shows a consistent presence of a nocturnal low-level jet and predominant southerly wind directions through the boundary layer at SGP. The inter-annual variability at SGP is low (<3.5%), with a mean annual wind speed of approximately 7 m s -1 at 100 m above ground level. Boundary layer turbulence and moisture transport from Doppler and Raman lidars are evaluated, which provides evidence of increased water vapor mass flux into the great plains during nocturnal low-level jets. The moisture flux from nocturnal low-level jets is observed to be maximum during summer periods. A novel machine learning algorithm is implemented to accurately estimate the planetary boundary layer height, providing further insights into growth and destruction of the convective boundary layer height during various seasons and land-atmosphere conditions. The high frequency of low-level clouds during winter, spring and fall seasons is validated using the multi-sensor array and satellite estimates of cloud top height. Satellite vegetative fraction data provides insight into seasonal surface roughness and vegetation variability around SGP site.

54 ENVIRONMENTAL SCIENCES↗