Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PELLETING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Steam reforming of n-hexane on pellet and monolithic catalyst beds. A comparative study on improvements due to heat transfer

Monolithic catalysts with higher available active surface areas and better thermal conductivity than conventional pellets beds, making possible the steam reforming of fuels heavier than naphtha, were examined. Performance comparisons were made between conventional pellet beds and honeycomb monolith catalysts using n-hexane as the fuel. Metal-supported monoliths were examined. These offer higher structural stability and higher thermal conductivity than ceramic supports. Data from two metal monoliths of different nickel catalyst loadings were compared to pellets under the same operating conditions. Improved heat transfer and better conversion efficiencies were obtained with the monolith having higher catalyst loading. Surface-gas interaction was observed throughout the length of the monoliths.

Source record↗

Fusible pellet transport and storage of heat

A new concept for both transport and storage of heat at high temperatures and heat fluxes is introduced and the first steps in analysis of its feasibility is taken. The concept utilizes the high energy storage capability of materials undergoing change of phase. The phase change material, for example a salt, is encapsulated in corrosion resistant sealed pellets and transported in a carrier fluid to heat source and storage. Calculations for heat transport from a typical solar collector indicate that the pellet mass flow rates are relatively small and that the required pumping power is only a small fraction of the energy transport capability of the system. Salts and eutectic salt mixtures as candidate phase change materials are examined and discussed. Finally, the time periods for melting or solidification of sodium chloride pellets is investigated and reported.

Bahrami, P. A.↗

A gel-halo sample pellet: The best of both worlds? Stubby zones without a constricted sample gate

This reduces cell quantity, in the same way as does a narrower bore sample gate. The cells are confined to the center of the gate, inside a halo of electrolyte (D-1 buffer, here) immobilized by gel, which halo mechanically retains the ice pellet in position prior to thaw. The gel halo can be retained by the same gentle ridge as is contemplated for the ice pellet, and the ice pellet can be likewise retained within the gel halo.

Hinckley, J. O. N.↗

Cleaning By Blasting With Pellets Of Dry Ice

Dry process strips protective surface coats from parts to be cleaned, without manual scrubbing. Does not involve use of flammable or toxic solvents. Used to remove coats from variety of materials, including plastics, ceramics, ferrous and nonferrous metals, and composites. Adds no chemical-pollution problem to problem of disposal of residue of coating material. Process consists of blasting solid carbon dioxide (dry ice) pellets at surface to be cleaned. Pellets sublime on impact and pass into atmosphere as carbon dioxide gas. Size, harness, velocity, and quantity of pellets adjusted to suit coating material and substrate.

Fody, Jody↗

Experimental Demonstration of High Frequency ELM Pacing by Pellet Injection on DIII-D and Extrapolation to ITER

. The injection of high repetition rate deuterium pellets is shown to trigger high-frequency edge localized modes (ELMs) in otherwise low natural ELM frequency H-mode deuterium discharges in the DIII-D tokamak. The resulting triggered ELMs have significantly lower energy and particle fluxes to the divertor than the natural ELMs. The plasma global energy confinement and density are not strongly affected by the pellet perturbations. The plasma core impurity density is strongly reduced with the application of the pellets. These experiments were performed in plasmas designed to match the ITER baseline configuration in shape and normalized operation with input power just above the H-mode power threshold. This strongly reduced ELM intensity shows promise for exploitation in ITER to control ELM size while maintaining high plasma purity and performance.

Baylor, Larry R↗

Fast Imaging of Intact and Shattered Cryogenic Neon Pellets

Compact condensed-matter injection technologies are increasingly used in magnetic fusion. One recent application is in disruption mitigation. An imaging system with less-than-100- m- and sub- s-resolution is described and used to characterize intact and shattered cryogenic neon pellets. Shattered pellets contain fine particles ranging from tens of m to about 7 mm. Time-of-flight analyses indicate that pellets could slow down if hitting the wall of the guide tube. Fast high-resolution imaging systems are thus useful to neon and other condensed-matter injector development.

Wang, Zhehui↗

Minimizing Transuranic Waste Generated in Hot Cells at Oak Ridge National Laboratory Through Use of a Non-Destructive CO{sub 2} Pellet Cleaning System - 19577

Wastes generated in shielded hot cells containing materials contaminated with transuranic (TRU) waste present unique problems in waste disposal at Department of Energy (DOE) sites. Oak Ridge National Laboratory (ORNL) routinely processes materials contaminated with TRU waste from the High Flux Isotope Reactor (HFIR) and from other sources (both on and off-site) in their hot cell facilities, generating wastes that require eventual disposal. The waste streams generated by these processes are often high activity and exhibit high dose rates, driving them into the remote-handled (RH) category at the Waste Isolation Pilot Plant (WIPP). Reduction of the TRU waste footprint is desirable from a disposal cost perspective due to constraints with RH waste processing and a lack of space availability at the WIPP. Historically TRU waste generated at ORNL has been processed by the TRU Waste Processing Center (TWPC), which belongs to the Department of Energy's Office of Environmental Management (DOE-EM). Now that Oak Ridge legacy TRU waste is reaching its final stage, DOE-EM has turned over the mission of processing newly-generated TRU waste streams to the DOE Office of Science at ORNL. To reduce the volume of potential TRU waste occupying valuable space in the ORNL Hot Cells, a non-destructive CO{sub 2} pellet cleaning system will be used to capture particulate contaminants removed from the surfaces of waste inside the ORNL Non-Reactor Nuclear Facilities (NNFD) Hot Cells at the Irradiated Fuels Examination Laboratories (IFEL). The particulate will be segregated by particle size and captured for disposal later. This action will separate some of the TRU isotopes (particulate) from the larger waste volume (debris waste items), resulting in both lower waste disposal costs and reduced TRU waste volumes. This will be accomplished through a specialized cyclone separator. Secondary wastes are usually generated through other methods of decontamination, such as water jets and abrasive agents. These secondary wastes are absent with the CO{sub 2} pelletized system, due to sublimation of the dry ice upon impact. This is an important consideration with IFEL, a facility whose primary mission is to perform a series of R and D testing on nuclear fuel rods. Liquid is not a feasible method of decontamination as the IFEL's drains in the Hot Cells were plugged years ago due to Resource Conservation and Recovery Act (RCRA) regulations. Constraints at IFEL, such as criticality safety concerns with use of hydrogenous materials, are also alleviated with the non-destructive CO{sub 2} pellet cleaning system. These are a couple of the considerations why this method of decontamination is preferred. Due to concerns with oxidizers at WIPP grouting will be performed on the contaminated particulate produced during the trapping by the cyclone separation phase. This method will comply with mitigating oxidizing properties in TRU waste, required by the recently published Basis of Knowledge (BoK) document as part of Acceptable Knowledge (AK) by WIPP. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Assessment of the analysis capability for core-wide PWR pellet-clad interaction screening of Watts Bar Unit 1

This report illustrates the application of the Virtual Environment for Reactor Applications simulation environment to pressurized water reactor core-wide pellet-clad interaction screening, with emphasis on the multi-dimensional analysis capabilities of the BISON fuel performance code. The Virtual Environment for Reactor Applications codes utilized in this effort include the BISON fuel performance code and the VERA-CS sub-element, which combines the MPACT neutron transport code and the COBRA-TF thermal-hydraulics code. The target reactor for this work is Watts Bar Unit 1, cycle 6 and cycle 7, selected on the basis that pellet-clad interaction failures had occurred during power start up in both cycles, despite the moderate power levels. These instances of failure at Watts Bar Unit 1 offered an interesting test of the code’s veracity and a particularly challenging condition for this assessment.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Effect of Thermal Storage on the Emissions and Efficiency Performance of a Wood Pellet-Fired Residential Boiler

Wood pellet boilers for residential heating applications offer the promise of low emissions, high efficiency, and automatic operation. However, when operated in the field, these units operate often at very low loads causing them to cycle. In this study, the performance of a 25-kW modern pellet boiler under emulated field conditions and fixed nominal loads of 15% and 100% has been studied in a lab—with and without a buffer tank. A dilution tunnel approach was used for the measurement of particulate emissions, in accordance with U.S. certification testing requirements under EPA Methods 28 WHH and 28 WHH PTS. Results show that increasing the amount of thermal storage used decreases cycling rates leading to decreased emissions and increased efficiency. Without thermal storage, integrated efficiency over a 15% load test period was 57%, compared to 74% when thermal storage was used. Particulate emissions were 180 mg/MJ and 64 mg/MJ for the 15% load case without and with thermal storage, respectively.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Hot-tail electrons’ impact on assimilation and injection penetration of D2 shattered pellet injections

The assimilation and the penetration of injected materials play significant roles in the mitigation efficiency of shattered pellet injection (SPI) as a disruption mitigation system (DMS), hence an accurate description of the fragment ablation rate is desirable. Current mainstream 3D MHD codes modelling SPIs mostly assume instantaneous thermalization between the previously hot ambient electrons and the newly released cold electrons. This could result in underestimation of the ablation rate if the hot electron thermalization time is comparable or even longer than the fragment flying time across flux tubes, putting the validity of these 3D SPI simulations into question. To resolve this doubt, we, in this study, investigate the thermalization dynamics and the overall hot-electron impact. The finite-time collisional thermalization of hot-tail electrons in a rapidly cooling plasma, as well as the so-called ‘self-limiting’ effect are considered. The former effect tends to deplete the colder population within a hot-tail species, while the latter is found to preferentially deplete the higher energy population. The combined result is found to cause an almost self-similar decay of the hot electron distribution function, while its shape does not deviate much from that of Maxwellian distribution and the mean energy does not change much during the thermalization process. Based on this observation, axisymmetric JOREK D2 SPI simulations were carried out with additional hot-tail contribution to evaluate their overall impact onto the injection assimilation and penetration. It is found that the hot-tail effect indeed causes enhanced assimilation and shallower penetration, although the overall effect depends on the exact injection configuration, with the slow injection showing negligible hot-tail effect while the fast single non-shattered pellet case shows drastic hot-tail ablation enhancement. For ITER-like SPI parameters, there is no significant deviation in the total assimilation, but some deviation in the injection penetration is observed for the fast injection velocity cases.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Pre-Feasibility Analysis of Pellet Manufacturing on the Former Loring Air Force Base Site

The U.S. Environmental Protection Agency (EPA) Office of Solid Waste and Emergency Response, in accordance with the RE-Powering America's Lands initiative, engaged the U.S. Department of Energy's (DOE) National Renewable Energy Laboratory (NREL) to conduct feasibility studies to assess the viability of developing renewable energy generating facilities on contaminated sites. This site, in Limestone, Maine—formerly the location of the Loring Air Force Base but now owned by the Aroostook Band of Micmac—was selected for the potential to produce heating pellets from woody feedstock. Biomass was chosen as the renewable energy resource to evaluate based on abundant woody-biomass resources available in the area. NREL also evaluates potential savings from converting existing Micmac property from oil-fired heating to pellet heating.

09 BIOMASS FUELS↗

Development of a Twin-Screw D-2 Extruder for the ITER Pellet Injection System

A twin-screw extruder for the ITER pellet injection system is under development at the Oak Ridge National Laboratory. The extruder will provide a stream of solid hydrogen isotopes to a secondary section, where pellets are cut and accelerated with single-stage gas gun into the plasma. A one-fifth ITER scale prototype extruder has been built to produce a continuous solid deuterium extrusion. Deuterium gas is precooled and liquefied before being introduced into the extruder. The precooler consists of a copper vessel containing liquid nitrogen surrounded by a deuterium gas filled copper coil. The liquefier is comprised of a copper cylinder connected to a Cryomech AL330 cryocooler, which is surrounded by a copper coil that the precooled deuterium flows through. The lower extruder barrel is connected to a Cryomech GB-37 cryocooler to solidify the deuterium (at approximate to 15 K) before it is forced through the extruder nozzle. A viewport located below the extruder nozzle provides a direct view of the extrusion. A camera is used to document the extrusion quality and duration. A data acquisition system records the extruder temperatures, torque, and speed, upstream, and downstream pressures. This paper will describe the prototype twin-screw extruder and initial extrusion results.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Aromatics and phenols from catalytic pyrolysis of Douglas fir pellets in microwave with ZSM-5 as a catalyst

Microwave assisted catalytic pyrolysis was investigated to convert Douglas fir pellets to bio-oils by a ZSM-5 Zeolite catalyst. A central composite experimental design (CCD) was used to optimize the catalytic pyrolysis process. The effects of reaction time, temperature and catalyst to biomass ratio on the bio-oil, syngas, and biochar yields were determined. GC/MS analysis results showed that the bio-oil contained a series of important and useful chemical compounds. Phenols, guaiacols, and aromatic hydrocarbons were the most abundant compounds which were about 50-82 % in bio-oil depending on the pyrolysis conditions. Comparison between the bio-oils from microwave pyrolysis with and without catalyst showed that the catalyst increased the content of aromatic hydrocarbons and phenols. A reaction pathway was proposed for microwave assisted catalyst pyrolysis of Douglas fir pellets.

Microwave, Catalytic pyrolysis, douglas fir pellet↗

Failure behavior of SiC/SiC composite tubes under strain rates similar to the pellet-cladding mechanical interaction phase of reactivity-initiated accidents

The mechanical response of a nuclear-grade silicon carbide fiber-reinforced silicon carbide matrix (SiC/SiC) composite was investigated under mechanical loading conditions mimicking the pellet-cladding mechanical interaction (PCMI) phase of a reactivity-initiated accident (RIA). In a RIA, cladding deformation and failure can be induced by the rapid thermal expansion of the nuclear fuel. A pulse-controlled modified-burst test was used to investigate RIA-like PCMI scenarios on SiC/SiC composite samples at pulse widths from 12 to 100 ms.The strain-driven nature of the cladding sample deformation was due to the rapid internal pressurization and subsequent expansion of a secondary tube. A digital-image correlation technique was used to measure strains from the speckle-painted outer surface of the tubes. The failure strains of samples tested at slower rates, such as RIA event durations of 52 and 100 ms, showed good agreement with the literature-reported values for similar composites tested at slow strain rates. Additionally, the failure strain showed good agreement with reference expansion-due-to-compression tests at slow strain rate. However, a decrease in the failure strain was determined for the fast-rate (12 ms) tests. This indicated that the failure strain of these composites might be influenced by the strain rate during RIA-like events. In conclusion, the failure strains observed in the tests corresponded to local energy depositions of approximately 50 cal/g UO 2 from hot zero power, with an initial condition of pellet–cladding gap closure prior to the event. In-pile transient testing of these concepts that would result in hoop strain due to PCMI in the range of 0.5–1.0% is recommended.

36 MATERIALS SCIENCE↗

Production of more ideal uranium trioxide microspheres for the sol-gel microsphere pelletization process without the use of carbon

Renewed interest by the U.S. Department of Energy in the sol-gel microsphere pelletization process led to an evaluation of dried uranium trioxide (UO 3 ) microspheres produced without the use of carbon by the internal gelation process at Oak Ridge National Laboratory. An earlier study has shown that less dense UO 3 microspheres led to uranium dioxide pellets with higher densities. This effort identified feed formulations that produced dried UO 3 microspheres with the lowest tap densities for gelation temperatures of 333, 343, 353, and 363 K. The tap densities of these dried UO 3 microspheres ranged from 680 to 820 kg/m 3 , which were significantly lower than the previously reported low UO 3 density of 900 kg/m 3 . This study confirmed an earlier observation that the effects of gelation conditions on the properties of the gel sphere are complex since only two of the four best formulations were similar in composition. As a result, the need to age the wet gel spheres in the gelation medium for 20 min at the end of the experiment was also confirmed.

36 MATERIALS SCIENCE↗

Molybdenum and Tungsten isotope compositions of UO 2 fuel pellets: Implications for isotopically enriched taggants

The addition of isotopically enriched taggants to material at the front end of the nuclear fuel cycle could be a powerful tool used to assist law enforcement authorities should material outside of regulatory control be found. Two potential candidates for this purpose are molybdenum (Mo) and tungsten (W) as both elements have five or more stable isotopes and are trace elements contained within nuclear fuel. So there is a concern that Mo and W could undergo isotope fractionation during processes like uranium enrichment and to date, it is unknown if nuclear fuels have natural Mo and W isotope compositions. If Mo and W isotopic variability is present in nuclear fuels, this would hinder the use of these elements as isotopic taggants because it would be difficult to discern the original taggant isotope composition with high confidence. Therefore, a set of 16 low enriched uranium (LEU) fuel pellets from US commercial producers was analyzed using multi collector-inductively coupled plasma mass spectrometry (MC-ICPMS) to determine Mo and W isotope compositions (i.e., 94 Mo/ 92 Mo, 95 Mo/ 92 Mo, 96 Mo/ 92 Mo, 97 Mo/ 92 Mo, 98 Mo/ 92 Mo, 183 W/ 182 W, 184 W/ 182 W, and 186 W/ 182 W). Relative to terrestrial standards, LEU fuel pellets have variable Mo and W isotope compositions, thereby complicating the use of these elements as isotopically enriched taggants. As such, this work demonstrates that the isotope composition of any potential taggant must be well characterized in the base nuclear fuel prior to any taggant addition. Furthermore, these results suggest that Mo and W are not ideal candidates for isotopically enriched taggants.

58 GEOSCIENCES↗

Spectroscopic diagnostics for ablation cloud of tracer-encapsulated solid pellet in LHD

In the Large Helical Device (LHD), various spectroscopic diagnostics have been applied to study the ablation process of an advanced impurity pellet, tracer-encapsulated solid pellet (TESPEL). The total light emission from the ablation cloud of TESPEL is measured by photomultipliers equipped with individual interference filters, which provide information about the TESPEL penetration depth. The spectra emitted from the TESPEL ablation cloud are measured with a 250 mm Czerny-Turner spectrometer equipped with an intensified charge coupled device detector, which is operated in the fast kinetic mode. This diagnostic allows us to evaluate the temporal evolution of the electron density in the TESPEL ablation cloud. In order to gain information about the spatial distribution of the cloud parameters, a nine image optical system that can simultaneously acquire nine images of the TESPEL ablation cloud has recently been developed. Several images of the TESPEL ablation cloud in different spectral domains will give us the spatial distribution of the TESPEL cloud density and temperature.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Pellet charge exchange helium measurement using neutral particle analyzer in large helical device

It is very important to investigate the confinement of {alpha} particles, which will be produced by nuclear reactions in ITER and fusion reactors. The pellet charge exchange (PCX) measurement is one of the most powerful methods because it can directly provide the profile of the {alpha} particle energy spectra in a plasma. In the large helical device, PCX using tracer encapsulated solid pellet (TESPEL) has been tried in many hydrogen and helium plasmas, including helium accelerated by using the cyclotron resonance heating. In the PCX, we use the compact neutral particle analyzer without simultaneous mass separation ability. The helium particle measurement can be achieved by the application of voltage in the condenser plate. The scattering of hydrogen particle is carefully considered during the estimation of the helium amount. The radial helium profiles can also be obtained by comparing four TESPEL injection shots with/without higher harmonic fast wave heating and at applied plate voltages for He or H, respectively.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗