SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The HL-LHC Inner Triplet quadrupole magnets use Nb 3 Sn superconductor for the first time in a particle accelerator. Coil peak field, forces, and stored energy density are significantly higher than in previous accelerator magnets. The original design addressed all these challenges. Lessons learned in the early phases made the final design and specifications for series magnets more robust.
Relaxor ferroelectrics have drawn attention for possible applications in solid-state cooling and thermal energy harvesting, owing to their electrothermal energy conversion properties. Here, we have synthesized and characterized the structure–property correlations of a new Sn- and Nb-doped (Ba,Ca)TiO 3 relaxor ferroelectric with large pyroelectric and electrocaloric effects over a broad temperature range. We observed two peaks for the temperature-dependent pyroelectric coefficient: (i) -(∂P/∂T) ~ 563 µC/(m 2 K) at T~ 270 K and (ii) -(∂P/∂T) ~ 1021 µC/(m 2 K) at T~ 320 K. In addition, a broad peak for electrocaloric temperature change is observed near 320 K with a relative cooling power of ~17 J/kg. These properties could be correlated to structural changes observed using X-ray diffraction at two different temperature ranges in the material. Analysis of high-energy X-ray scattering and specific heat capacity data revealed a transition from the cubic to tetragonal phase near T m ~ 320 K, whereas an additional increase in the tetragonality (c/a) of the polar phase is observed below T s ~ 270 K.
New potential rf applications of superconductors emerged with the need to operate in high dc magnetic fields (up to 16 T) where vortex motion dictates the response: the beam screen coating of the Future Circular Collider (FCC) [1] and haloscopes, i.e. rf cavities for the axions detection [2]. However, very few data are available in the required regimes. We present in this work measurements of the surface impedance Z up to 12 T on bulk Nb₃Sn and YBCO thin films grown by different techniques. The measurements are performed with a dielectric loaded resonator operating at 15 GHz. We obtained the vortex motion resistivity and extracted the high frequency vortex motion parameters [3]: the depinning frequency, the flux-flow resistivity and the pinning constant, as well as their temperature and field dependences. Substantial differences are highlighted in the high frequency pinning properties of the studied materials, providing useful information on possible improvements in view of applications. A comparison with the results obtained in the microwave frequency range at lower fields (up to 1 T) is given.
The mechanical vulnerability of the Nb3Sn-coated cavities is identified as one of the significant technical hurdles toward deploying them in practical accelerator applications in the not-so-distant future. It is crucial to characterize the material's mechanical properties in ways to address such vulnerability. Nanoindentation is a widely used technique for measuring the mechanical properties of thin films that involves indenting the film with a small diamond tip and measuring the force-displacement response to calculate the film's elastic modulus, hardness, and other mechanical properties. For the first time, the nanoindentation analysis was performed on multiple vapor-diffused Nb3Sn samples coated at Jefferson Lab and Fermilab coating facilities. This contribution will discuss the first results obtained from the nanoindentation of Nb3Sn-coated Nb samples prepared via the Sn vapor diffusion technique.
Fermilab in the framework of the U.S. Magnet Development Pro-gram (US-MDP) has developed and fabricated a 15 T Nb 3 Sn dipole demonstrator for a post-LHC hadron collider. In June 2019 the magnet was tested and reached a world record field in the aperture of 14.1T at 4.5 K.
While much progress has been made in improving the performance of cavities in the past decade, reproducible performance remains elusive. This renewal of “The cost of grain boundaries on the performance of superconducting cavities” examines in further depth the interactions between forming and annealing processes and functional performance at the scale of dislocation substructure and grain boundaries. There are five tasks identified in the renewal, which are: Characterization / analysis of current cavity technology: Effect of deformation, heat treatment, surface treatments, and residual damage on cavity function (Lee and Bieler) Characterization of dislocation mechanisms in single and bicrystals (Bieler) Quantifying effects of impurities and deformation mechanisms in Nb using density functional theory calculations (Solanki) Crystal plasticity constitutive model development (Pourboghrat and Eisenlohr) Modeling and measuring thermal conductivity in thin layers (Wright)
This work demonstrated both NbN and Nb make good electrodes for stabilizing orthorhombic phase of Hf 0.6 Zr 0.4 O 2 ferroelectric films. Wake up are < 100 cycles. P r can be as high as 30 µC/cm 2 - respectively 14 and 18 µC/cm 2 here. Further, capacitance suggests an orthorhombic phase can be stabilized. Addition of a linear dielectric under modest thickness can tune the P r and reduce leakage.
Upcoming projects requiring high-Q ~650 MHz medium-to-high-! elliptical cavities drive a need to understand magnetic RF loss mechanisms and mitigations in greater detail. We explore the fastcooldown method, and high-temperature annealing (900°C) in 644- 650 MHz SRF cavities fabricated from two different niobium vendors: Tokyo-Denkai (TD), and Ningxia (NX). Using EBSD and PPMS methods, we aim to trace cavity flux expulsion efficiency to specific, measurable properties of the bulk niobium material, which, if identified, can lead to methods by which the flux expulsion properties of Nb material can be predicted prior to cavity fabrication.
Nb3Sn is a next-generation superconducting material that can be used for future superconducting radiofrequency (SRF) accelerator cavities, promising better performance, cost reduction, and higher operating temperature than Nb. The Sn vapor diffusion method is currently the most preferred and successful technique to coat niobium cavi-ties with Nb3Sn. Among post-coating treatments to opti-mize the coating quality, higher temperature annealing without Sn is known to degrade Nb3Sn because of Sn loss. We have investigated Nb3Sn/Nb samples briefly annealed at 800-1000 °C for 10 and 20 minutes to poten-tially improve the surface to enhance the performance of Nb3Sn-coated cavities. Following the sample studies, a coated single-cell cavity was sequentially annealed at 900 °C and tested its performance each time, improving the cavity's quality factor relatively. This paper summarizes the sample studies and discusses the RF test results from sequentially annealed SRF Nb3Sn/Nb cavity.
The mechanical vulnerability of the Nb3Sn-coated cavities is identified as one of the significant technical hurdles toward deploying them in practical accelerator applications in the not-so-distant future. It is crucial to characterize the material's mechanical properties in ways to address such vulnerability. Nanoindentation is a widely used technique for measuring the mechanical properties of thin films that involves indenting the film with a small diamond tip and measuring the force-displacement response to calculate the film's elastic modulus, hardness, and other mechanical properties. For the first time, the nanoindentation analysis was performed on multiple vapor-diffused Nb3Sn samples coated at Jefferson Lab and Fermilab Nb3Sn coating facilities. This contribution will discuss the first results obtained from the nanoindentation of Nb3Sn-coated Nb samples prepared via the Sn vapor diffusion technique.
The SRF technology developed for accelerators can be successfully applied to new applications, including quantum computing, dark matter searches and beyond the standard model physics. The ultra-high quality factor of SRF cavities can al-low to achieve unprecedented sensitivity in fields outside of the usual accelerator applications, for examples fundamental and beyond the standard model physics. Applications of SRF cavities for gravitational waves searches are also being investigated. The SQMS Physics and Sensing thrust is working on this effort as it strives to combine SRF cavities with QIS, with a focus on BSM and fundamental physics. Using Nb SRF cavities, we run a proof of principle search for the dark photon dark matter candidate at fixed frequency demonstrating the deepest sensitivity to wavelike dark mater [1]. The Dark SRF experiment uses two 1.3GHz SRF cavities to conduct a light shining through wall (LSW) experiment to attempt producing and detecting dark photons in the laboratory. The results of this first superconducting LSW search were recently published [2] and we are now working on the second phase of the experiment, which will be run in a dilution refrigerator using 2.6GHz SRF cavities. In addition to the limits we have achieved, we will also present the experiments we are currently developing, such as the heterodyne axion DM search [3, 4], the SERAPH series of experiments, and gravitational waves searches based on SRF cavities as proposed in [5-8].
The Nb 3 Sn wires received from LBNL include the original round wires as well as the extracted wires from Rutherford cables. Total of 12 samples were prepared and heat treated. Five of them were tested for electric field versus current (E-I), among them 4 samples were further tested for electric field versus magnetic field (E-H). E-I traces were measured in magnetic field between 5 T and 8 T at 4.2 K. The critical currents of these sample are between 924 A and 993 A at 5 T. E-H measurements were performed at currents between 900 and 1500 A at 4.2 K. The stability currents, which is defined as the maximum current without quench during the E-H test, are determined to be between 1100 A and 1400 A. A separate Excel file presenting all the critical current and E-H curves is attached.
Neutron Spin Echo (NSE) spectroscopy uniquely measures the Q-dependence of slow relaxation dynamics, and having such a machine at HFIR will advance polarized neutron spectroscopy and promote the study of biophysical and energy materials using neutrons. The 2018 Instrument Advisory Board (IAB) advises Neutron Sciences Directorate, ORNL to upgrade the cold neutron delivery system at HFIR, addressing geometrical challenges in neutron transfer from the bright cold source. This is being optimized now: the entrance to the guide system is moving closer to the source, and more guides are being added. However, there are still significant challenges to making the cold flux at the sample world-class. With the proposed guide system, NB-2 can deliver more than 10 6 polarized neutrons per cm 2 /sec below 8Å, and probably 10Å with further optimization. With no potential for running user experiments with neutrons longer than 15Å, the utility of such a machine for biological studies is limited. However, there is a large demand for this class of spectrometer in materials science, chemical engineering, and nanotechnology. Workshops held over the past decade and the three-source vision have highlighted the community's need for a low-angle, high-energy resolution spectrometer at HFIR. A detailed design study of this spectrometer is needed, focusing on optimizing the neutron delivery system for SANS-type studies. This neutron spectrometer would complement studies already performed on both SNSNSE and BASIS by overlapping and extend the dynamic range accessible, while acknowledging the proposed machine, EXPANSE, at the Second Target Station. Two technologies currently exist for such a spectrometer: traditional DC solenoids like those on BL-15 at SNS and IN15 at the ILL, and RF-flipper-based machines similar to RESEDA at FRMII. Either instrument would satisfy the scientific justification. However, there are strong business and scientific cases to utilize the thermal flux, the resonant expertise developed at ORNL, and the potential to utilize an entangled beam of neutrons to probe quantum matter by adopting the neutron resonant spin-echo configuration.
It is well known that age hardening occurs in U-6%Nb (Ref. 1-9). Figure 1 shows that increases in hardness occur at aging temperatures up to ~400°C, and overaging occurs above ~450°C. Overaging occurs by cellular decomposition of the αʺ b martensite, similar to overaging reactions in other uranium alloys. But the mechanism of age hardening remains elusive, particularly in its early stages.
In the past few years, new high specific heat Nb 3 Sn wires have gained much focus at FNAL. Indeed, they have proved to be more stable against thermal perturbations with respect to standard wires. Nevertheless, a trade off exists between their thermal efficiency and production feasibility. In this report I describe the thermal and structural models that I have developed by exploiting ANSYS Mechanical APDL ® , which I got acquainted with at the beginning of my training. The aim has been to optimize the location of high specific heat elements in order to obtain an optimal thermal stability, while minimizing the risk of wire breakage during drawing. FEM results are compared with experimental ones made beforehand. Other minimum quench energy (MQE) thermal models have been developed for expected new experimental results. New data may improve the understanding of the embedded physical uncertainties in the model.
Modern particle accelerators depend on Superconducting Radio Frequency (SRF) cavities made from high-purity niobium (Nb) to achieve optimal performance, including high quality factors and strong accelerating gradients. However, when exposed to air, niobium naturally forms a complex oxide layer that can introduce surface imperfections and carbon contamination. This work examines an alternative oxidation strategy under oxygen-rich conditions to better regulate the oxide formation process. The ultimate objective is to improve surface uniformity and cleanliness, thereby reducing defect density and enhancing performance. We used Confocal Microscopy, Scanning Electron Microscopy (SEM), and X-Ray Photoelectron Spectroscopy (XPS) to analyze surface changes. We used standard metrics, like Arithmetic Average Roughness (Ra) and Root Mean Square (Rq). Three oxidation methods were applied: short, extended, and a repeated HF and H₂O₂ oxidation process. Preliminary results show promising reductions in carbon contamination and surface defects.
An integrated computational materials engineering (ICME) method is in development for rapid thermodynamic experimental investigation and high-fidelity computational modeling of refractory multi-principal element alloys (RMPEAs). These ultra-high-temperature (UHT) alloys are of interest for structural applications in extreme environments, but deficiency of reliable data, especially melting temperatures, impedes the prediction of alloys with favorable properties. The method leverages UHT capabilities and computational expertise of LLNL’s Materials Science Division and the McCormack Lab’s UHT conical nozzle levitation (CNL) system to iteratively map the Nb-Ta-Zr phase space, with focus on the liquidus surface, through targeted experiments selected by quantifying uncertainty in the thermodynamic model fitting parameters. This method will reduce the time to map uncharted RMPEA phase space and thereby accelerate discovery and development of advanced materials for applications in extreme environments.
High strength, high conductivity copper alloys that can resist creep at high temperatures are one of the primary candidates for efficient heat exchangers in fusion reactors. Cu–Cr–Nb–Zr (CCNZ) alloys, which were designed to improve the strength and creep life of ITER Cu–Cr–Zr (CCZ) reference alloys, have been found to have comparable electrical conductivity and tensile properties to CCZ alloys. The measured creep rupture times for these improved alloys is about ten times higher than the ITER reference alloys at 90–125 MPa at 500 °C. However, the effects of neutron irradiation on these alloys, and the ensuing material properties, have not been studied; thus, their utility in a fusion reactor environment is not well understood. This study characterizes the room temperature mechanical and electrical properties of a neutron-irradiated CCNZ alloy and compares them to a neutron-irradiated ITER reference heat sink CCZ alloy. Tensile specimens were neutron irradiated in the High Flux Isotope Reactor (HFIR) to 5 dpa between 250 °C and 325 °C. Post-irradiation characterization included electrical resistivity measurements, hardness, and tensile tests. Microstructural evaluation used scanning electron microscopy, energy dispersive x-ray spectroscopy, and atom probe tomography to characterize the irradiation-produced changes in the microstructure and investigate the mechanistic processes leading to post-irradiation properties. Transmutation calculations were validated with composition measurements from atom probe data and used to calculate contributions to the increased electrical resistivity measured after irradiation. Comparisons with CCZ alloys in the same irradiation heat found that the post-irradiated CCNZ and CCZ alloys had comparable electrical resistivity. Although CCNZ alloys suffered more irradiation hardening than CCZ, the overall tensile behavior deviated very little from non-irradiated values in the temperature range studied.