SEARCH · Engineering Papers

Results for “Low metal loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

All sources NASA NTRS DOE OSTI

NASA NTRS2009

Experimental Behavior of Fatigued Single Stiffener PRSEUS Specimens

NASA, the Air Force Research Laboratory and The Boeing Company have worked to develop new low-cost, light-weight composite structures for aircraft. A Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) concept has been developed which offers advantages over traditional metallic structure. In this concept a stitched carbon-epoxy material system has been developed with the potential for reducing the weight and cost of transport aircraft structure by eliminating fasteners, thereby reducing part count and labor. By adding unidirectional carbon rods to the top of stiffeners, the panel becomes more structurally efficient. This combination produces a more damage tolerant design. This document describes the results of experimentation on PRSEUS specimens loaded in unidirectional compression in fatigue and to failure.

Jegley, Dawn C.↗

NASA NTRS2010

Influence of Impact Damage on Carbon-Epoxy Stiffener Crippling

Jegley, Dawn C.↗

DOE OSTI2024

Design of the Electromagnetic Particle Injector (EPI) for Tokamak Deployment

Both predicting and controlling disruptions are critical and urgent issues for ITER as some disruptions with a short warning time may be unavoidable. For these cases, a rapid response disruption mitigation system (DMS) referred to as the electromagnetic particle injector (EPI) is being developed. The primary advantages of the EPI are its fast response time and high velocity, which have been demonstrated in offline experiments (Raman et al., 2021). The EPI is capable of accelerating a metallic sabot electromagnetically using a rail gun to the required velocities ( > 2 km/s) within 2 ms. Two high-field racetrack magnets able to generate fields over 2 T are positioned above and below the rails to permit high velocity at low rail currents, a requirement to minimize electrode erosion. At the end of the acceleration phase, a sabot capture mechanism retains the spent sabot inside the vacuum chamber that houses the EPI. At this point, it releases well-defined microspheres, or a shell pellet, of a radiative payload into the disrupting plasma. A remotely operated sabot loading system positioned behind the injector contains several pre-equipped sabots that can be loaded by an operator from the tokamak control room. The injector is interfaced to the tokamak through a guide tube attached to the front of the EPI vacuum chamber. Finally, the advantages of the EPI system over other DMSs under consideration are described in conjunction with the details of an EPI system designed for near-term test on an existing large tokamak.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Ducted Fuel Injection Provides Consistently Lower Soot Emissions in Sweep to Full-Load Conditions

Earlier studies have proven how ducted fuel injection (DFI) substantially reduces soot for low- and mid-load conditions in heavy-duty engines, without significant adverse effects on other emissions. Nevertheless, no comprehensive DFI study exists showing soot reductions at high- and full-load conditions. This study investigated DFI in a single-cylinder, 1.7-L, optical engine from low- to full-load conditions with a low-net-carbon fuel consisting of 80% renewable diesel and 20% biodiesel. Over the tested load range, DFI reduced engine-out soot by 38.1–63.1% compared to conventional diesel combustion (CDC). This soot reduction occurred without significant detrimental effects on other emission types. Thus, DFI reduced the severity of the soot–NO x tradeoff at all tested conditions. While DFI delivered considerable soot reductions in thepresent study, previous DFI studies at low- and mid-load conditions delivered larger soot reductions (>90%) compared to CDC operation at the same conditions. Therefore, the DFI configuration used here has been deemed nonoptimal (in terms of parameters such as the injector-spray and piston geometries), and several improvements are recommended for future studies with high-load DFI. Further, these improvements include employing better spray-duct alignment, a deeper piston bowl with a smaller injector umbrella angle, and a fuel injector that opens and closes faster. The study also suggests future research to make DFI ready for commercialization, such as metal-engine tests to ensure desirable DFI performance over an engine’s complete speed/load map. Overall, this study supports the continued development and commercialization of DFI to meet upcoming emissions regulations for heavy-duty vehicles. Specifically, multicylinder engine experiments and CFD simulations should be utilized to optimize the performance and clarify the full potential of DFI.

33 ADVANCED PROPULSION SYSTEMS↗

NASA NTRS1991

Mechanical behavior of a continuous fiber reinforced aluminum matrix composite subjected to transverse and thermal loading

The transverse properties of an aluminum alloy metal matrix composite reinforced by continuous alumina fibers were investigated. The composite is subjected to both mechanical and cyclic thermal loading. The results of an experimental program indicate that the shakedown concept of structural mechanics provides a means of describing the material behavior. When the loading conditions are within the shakedown region, the material finally responds in an elastic manner after initial plastic response, and for loading conditions outside the shakedown region, the material exhibits a rapid incremental plastic strain accumulation. The failure strain varies by an order of magnitude according to the operating conditions. Hence, for high mechanical and low thermal loading, the failure strains is small; for low mechanical and high thermal loading, the failure strain is large.

Jansson, S.↗

DOE OSTI2024

Promoted Ru/PrOx Catalysts for Mild Ammonia Synthesis

Ammonia synthesis is one of the most important chemical reactions. Due to thermodynamic restrictions and the reaction requirements of the current commercial iron catalysts, it is also one of the worst reactions for carbon dioxide emissions and energy usage. Ruthenium-based catalysts can substantially improve the environmental impact as they operate at lower pressures and temperatures. In this work, we provide a screening of more than 40 metals as possible promoter options based on a Ru/Pr2O3 catalyst. Cesium was the best alkali promoter and was held constant for the series of double-promoted catalysts. Ten formulations outperformed the Ru-Cs/PrOx benchmark, with barium being the best second promoter studied and the most cost-effective option. Designs of experiments were utilized to optimize both the pretreatment conditions and the promoter weight loadings of the doubly promoted catalyst. As a result, optimization led to a more than five-fold increase in activity compared to the unpromoted catalyst, therefore creating the possibility for low-ruthenium ammonia synthesis catalysts to be used at scale. Further, we have explored the roles of promoters using kinetic analysis, X-ray Photoelectron Spectroscopy (XPS), and in situ infrared spectroscopy. Here, we have shown that the role of barium is to act as a hydrogen scavenger and donor, which may permit new active sites for the catalyst, and have demonstrated that the associative reaction mechanism is likely used for the unpromoted Ru/PrOx catalyst with hydrogenation of the triple bond of the dinitrogen occurring before any dinitrogen bond breakage.

Chemistry↗

NASA NTRS1952

Friction and Surface Damage of Several Corrosion-resistant Materials

Friction and surface damage of several materials that are resistant to corrosion due to liquid metals was studied in air. The values of kinetic friction coefficient at low sliding velocities and photomicrographs of surface damage were obtained. Appreciable surface damage was evident for all materials tested. The friction coefficients for the combinations of steel, stainless steel, and monel sliding against steel, stainless steel, nickel, Iconel, and Nichrome ranged from 0.55 for the monel-Inconel combination to 0.97 for the stainless-steel-nickel combination; for steel, stainless steel, monel, and tungsten carbide against zirconium, the friction coefficient was approximately 0.47. Lower coefficients of friction (0.20 to 0.60) and negligible surface failure at light loads were obtained with tungsten carbide when used in combination with various plate materials.

ONTACT SURFACES, SLIDING↗

DOE OSTI2020

TCCR Operational Summary and Optimization for Tank 9 Processing - 20314

Savannah River Remediation (SRR) manages and operates the liquid waste facilities at Savannah River Site (SRS) for the Department of Energy (DOE). Stored liquid waste is a complex mixture of insoluble solids (sludge) and soluble salts in an alkaline solution. SRR has deployed the Tank Closure Cesium Removal (TCCR) system, a tank-side ion exchange process, to remove radioactive cesium from salt waste and enable onsite disposal of the resulting decontaminated salt solution as low-level waste at the Saltstone facilities. The TCCR system consists of two prefilters, four ion exchange (IX) columns, one resin trap, and a ventilation system. The IX process uses a form of inorganic crystalline silicotitanate (CST), which has a high affinity for cesium and other alkali metals, strontium, and actinides. This process is currently deployed utilizing salt feed from Tank 10, with future plans to dissolve solid salt in Tank 9 and transfer the salt solution to Tank 10 for processing through TCCR. The feed for TCCR must be created from salt-cake in Tank 10 through a dissolution process. Once enough salt has been dissolved, a qualification process is entered. This process characterizes the feed and ensures the cesium loading on the columns will not cause boiling of waste within the columns during or after processing. Once the batch has been qualified, salt waste is fed to the TCCR system through a transfer pump in the center of the tank. The waste is filtered through a set of two shielded, dead-end prefilters that prevent solids buildup in the columns. The filtered salt solution then travels to the shielded IX columns, which can be operated individually or in series, where the cesium is sorbed on the CST media. The decontaminated salt solution (DSS) then travels through a resin trap and out of the module to Tank 11. TCCR has successfully processed approximately 795,000 L of Tank 10H radioactive salt waste over two batches to date. There has not yet been a system induced shutdown. The prefilters performed as expected with only minor degradation in recovery of differential pressure after a backflush sequence. The time between backflushes decreased as each batch reached the end of processing. The hydraulics in the IXCs mostly performed as expected at all flow rates, except for one IXC that will be further investigated during Batch 3 processing. The TCCR system has shown some opportunities for more efficient processing during the length of the demonstration so far. For future processing of material from Tank 9H through Tank 10H and the TCCR unit, TCCR 1A will implement changes to the prefilters and the IXCs. The prefilters will have an increased surface area and a new filter media in an effort to increase time between filter swaps and improve backwashing cleaning capability. The IXCs will have a reduced diameter to allow for increased heat transfer out of the column and increased loading of Cs-137. Additionally, a new form of CST with an increased kinetic performance is being investigated for use during TCCR 1A operation. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

NASA NTRS1990

Composites boost 21st-century aircraft engines

Research and development in light-weight, high-temperature composite materials for ultrahigh-bypass engines to be used in high-speed civil transport/rotocraft is presented. It is noted that the expected benefits to be attained by this R&D include weight reduction, lowered fuel consumption, and lower direct operating costs. A major effort underway in this area is the Advanced High Temperature Engine Materials Technology Program (HITEMP) of NASA, which focuses on providing revolutionary high-temperature composite materials: to 425 C (800 F) for polymer-matrix composites (PMCs), to 1250 C (2280 F) for metal-matrix/intermetallic-matrix composites (MMCs/IMCs), and to as high as 1650 C (3000 F) for ceramic-matrix composites (CMCs). Analytical modeling is being used to investigate the structural behavior of these advanced materials in six distinct areas: micromechanics, deformation and damage, fatigue, fracture, trade-off studies, and load definition. It is concluded that the development of advanced materials such as high-temperature composites is highly dependent on the availability of high-temperature fibers. The wide range of fiber characteristics needed will require the development of more than one fiber. In general, a candidate fiber should have low density, high strength, high stiffness, a CTE matching the matrix, chemical compatibility with the matrix, environmental stability and appropriate fiber diameter.

Stephens, Joseph R.↗

NASA NTRS2003

Hydrostatic Stress Effects Incorporated Into the Analysis of the High-Strain-Rate Deformation of Polymer Matrix Composites

Procedures for modeling the effect of high strain rate on composite materials are needed for designing reliable composite engine cases that are lighter than the metal cases in current use. The types of polymer matrix composites that are likely to be used in such an application have a deformation response that is nonlinear and that varies with strain rate. The nonlinearity and strain rate dependence of the composite response is primarily due to the matrix constituent. Therefore, in developing material models to be used in the design of impact-resistant composite engine cases, the deformation of the polymer matrix must be correctly analyzed. However, unlike in metals, the nonlinear response of polymers depends on the hydrostatic stresses, which must be accounted for within an analytical model. An experimental program has been carried out through a university grant with the Ohio State University to obtain tensile and shear deformation data for a representative polymer for strain rates ranging from quasi-static to high rates of several hundred per second. This information has been used at the NASA Glenn Research Center to develop, characterize, and correlate a material model in which the strain rate dependence and nonlinearity (including hydrostatic stress effects) of the polymer are correctly analyzed. To obtain the material data, Glenn s researchers designed and fabricated test specimens of a representative toughened epoxy resin. Quasi-static tests at low strain rates and split Hopkinson bar tests at high strain rates were then conducted at the Ohio State University. The experimental data confirmed the strong effects of strain rate on both the tensile and shear deformation of the polymer. For the analytical model, Glenn researchers modified state variable constitutive equations previously used for the viscoplastic analysis of metals to allow for the analysis of the nonlinear, strain-rate-dependent polymer deformation. Specifically, we accounted for the effects of hydrostatic stresses. An important discovery in the course of this work was that the hydrostatic stress effects varied during the loading process, which needed to be accounted for within the constitutive equations. The model is characterized primarily by shear data, with tensile data used to characterize the hydrostatic stress effects.

Goldberg, Robert K.↗

NASA NTRS1960

Ignition of a Combustible Atmosphere by Incandescent Carbon Wear Particles

A study was made to determine whether carbon wear particles from carbon elements in sliding contact with a metal surface were sufficiently hot to cause ignition of a combustible atmosphere. In some machinery, electric potential differences and currents may appear at the carbon-metal interface. For this reason the effect of these voltages and currents on the ability of carbon wear particles to cause ignition was evaluated. The test specimens used in the investigation were carbon vanes taken from a fuel pump and flat 21-inch-diameter 2 metal disks (440-C stainless steel) representing the pump housing. During each experiment a vane was loaded against a disk with a 0.5-pound force, and the disk was rotated to give a surface speed of 3140 feet per minute. The chamber of the apparatus that housed the vane and the disk was filled with a combustible mixture of air and propane. Various voltages and amperages were applied across the vane-disk interface. Experiments were conducted at temperatures of 75, 350, 400, and 450 F. Fires were produced by incandescent carbon wear particles obtained at conditions of electric potential as low as 106 volts and 0.3 ampere at 400 F. Ignitions were obtained only with carbon wear particles produced with an electric potential across the carbon-vane-disk interface. No ignitions were obtained with carbon wear particles produced in the absence of this potential; also, the potential difference produced no ignitions in the absence of carbon wear particles. A film supplement showing ignition by incandescent wear particles is available.

Buckley, Donald H.↗

DOE OSTI2020

Correlating the influence of porosity, tortuosity, and mass loading on the energy density of LiNi 0.6 Mn 0.2 Co 0.2 O 2 cathodes under extreme fast charging (XFC) conditions

Extreme fast charging capabilities along with high energy density of Li-ion batteries are the key factors to increase the adoption of electric vehicles while eliminating the problem of range anxiety. The U.S Department of Energy has a goal of <12 min charging time with energy density of > 200 Wh kg -1 . A combined improvement in the electrode architecture, electrolyte properties, and separator membrane is necessary to achieve this goal. Cells with thin electrodes are capable of extreme fast charging at the expense of low energy density and high cost. Electrode engineering can maximize energy density. In this work, the influence of porosity, mass loading and charging protocols on capacity and energy density and electrode kinetics are investigated under extreme fast charging conditions. Increasing the mass loading from 11.5 mg cm -2 to 25 mg cm -2 compromises the rate performance due to the mass transport limitation and underutilization of thick electrodes. Furthermore, reducing the electrode porosity from 50% to 35% improves the rate performance ascribed to shorter Li ion diffusion length. Symmetric cells are cycled to verify the performance of the half cells, suggesting that Li metal plating is the rate limiting step under high current density.

25 ENERGY STORAGE↗

DOE OSTI2022

Impacts of engine lubrication oil-derived ash on soot oxidative reactivity on a catalytic gasoline particulate filter

Characterizing soot oxidation kinetics is crucial for understanding how gasoline particulate filters (GPFs) perform both in terms of filtration efficiency and pressure drop. The most common method for measuring soot oxidative reactivity is thermogravimetric analysis (TGA). Because TGA is an offline method, it may inaccurately predict how soot oxidizes on a GPF, especially if a catalytic washcoat is present that may enhance oxidation rates through surface interactions as the soot loads on the filter. In this work, a novel in-situ soot oxidative reactivity measurement method was developed. The method involved loading a catalytic GPF under high temperature conditions conducive to soot oxidation and measuring the filtration efficiency of 100 nm particles. A correlation was made between filtration efficiency and loaded soot mass on the filter to allow calculation of the soot oxidation rate. The method was evaluated in experiments using a 2.0 L gasoline direct injection (GDI) engine with three oils of varying additive packages, including an oil with a high zinc dialkyldithiophosphate (ZDDP) concentration, a non-additive, pure poly-alpha olefin (PAO) oil, and an oil with a high concentration of calcium sulfonate. Calculated specific soot oxidation rates ranged from ~0.06–0.6 min –1 and showed strong dependence on GPF inlet gas temperature and lubrication oil additive type. The results clearly demonstrated a catalytic effect of calcium-containing ash particles. Reactivity of soot produced by the engine running with the high calcium containing lubrication oil was increased. Similarly, the results indicated that the catalytic washcoat on the filter increased soot oxidation rates on-filter, especially at low soot loading. Conversely, the ZDDP oil additive exhibited a reactivity inhibiting effect, resulting in lower soot oxidation rates. Finally, this work represents the first known in-situ soot oxidative reactivity measurements on a GPF and elucidates the effect of lubrication oil additives and catalytic washcoat on oxidation rate.

42 ENGINEERING↗

DOE OSTI2021

Understanding how single-atom site density drives the performance and durability of PGM-free Fe–N–C cathodes in anion exchange membrane fuel cells

One of the most important needs for the future of low-cost fuel cells is the development of highly active platinum group metal (PGM)-free catalysts. For the oxygen reduction reaction, Fe–N–C materials have been widely studied in both acid and alkaline media. However, reported catalysts in the literature show quite different intrinsic activity and in-cell performance, despite similar synthesis routes and precursors. Here, two types of Fe–N–C are prepared from the same precursor and procedure – the main difference is how the precursor was handled prior to use. It is shown that in one case Fe overwhelmingly existed as highly active single-metal atoms in FeN4 coordination (preferred), while in the other case large Fe particles coexisting with few single metal atoms were obtained. As a result, there were drastic differences in the catalyst structure, activity, and especially in their performance in an operating anion exchange membrane fuel cell (AEMFC). Additionally, it is shown that catalyst layers created from single-atom-dominated Fe–N–C can have excellent performance and durability in an AEMFC using H 2 /O 2 reacting gases, achieving a peak power density of 1.8 W cm -2 – comparable to similar AEMFCs with a Pt/C cathode – and being able to operate stably for more than 100 h. Finally, the Fe–N–C cathode was paired with a low-loading PtRu/C anode electrode to create AEMFCs (on H 2 /O 2 ) with a total PGM loading of only 0.135 mg cm -2 (0.090 mg Pt cm -2 ) that was able to achieve a very high specific power of 8.4 W mg PGM -1 (12.6 W mg Pt< sup>-1 ).

36 MATERIALS SCIENCE↗

NASA NTRS1985

The role of silver in self-lubricating coatings for use at extreme temperatures

The advantages and disadvantages of elemental silver as a tribological material are discussed. It is demonstrated that the relatively high melting point of 961 deg C, softness, marked plasticity, and thermochemical stability of silver combine to make this metal useful in thin film solid lubricant coatings over a wide temperature range. Disadvantages of silver during sliding, except when used as a thin film, are shown to be gross ploughing due to plastic deformation under load with associated high friction and excessive transfer to counterface surfaces. This transfer generates an irregular surface topography with consequent undesirable changes in bearing clearance distribution. Research to overcome these disadvantages of element silver is described. A comparison is made of the tribological behavior of pure silver with that of silver formulated with other metals and high-temperature solid lubricants. The composite materials are prepared by co-depositing the powdered components with an airbrush followed by furnace heat treatment or by plasma-spraying. Composite coatings were formulated which are shown to be self-lubricating over repeated, temperature cycles from low temperature to about 900 deg C.

Sliney, H. E.↗

NASA NTRS1986

The use of silver in self-lubricating coatings for extreme temperatures

Sliney, H. E.↗

DOE OSTI2020

Building Electron/Proton Nanohighways for Full Utilization of Water Splitting Catalysts

Low electron/proton conductivities of electrochemical catalysts, especially earth-abundant nonprecious metal catalysts, severely limit their ability to satisfy the triple-phase boundary (TPB) theory, resulting in extremely low catalyst utilization and insufficient efficiency in energy devices. In this study, an innovative electrode design strategy is proposed to build electron/proton transport nanohighways to ensure that the whole electrode meets the TPB, therefore significantly promoting enhance oxygen evolution reactions and catalyst utilizations. It is discovered that easily accessible/tunable mesoporous Au nanolayers (AuNLs) not only increase the electrode conductivity by more than 4000 times but also enable the proton transport through straight mesopores within the Debye length. The catalyst layer design with AuNLs and ultralow catalyst loading (≈0.1 mg cm -2 ) augments reaction sites from 1D to 2D, resulting in an 18-fold improvement in mass activities. Furthermore, using microscale visualization and unique coplanar-electrode electrolyzers, the relationship between the conductivity and the reaction site is revealed, allowing for the discovery of the conductivity-determining and Debye-length-determining regions for water splitting. These findings and strategies provide a novel electrode design (catalyst layer + functional sublayer + ion exchange membrane) with a sufficient electron/proton transport path for high-efficiency electrochemical energy conversion devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1962

PROGRESS REPORT ON THE DEVELOPMENT OF PROTECTED CONSTRUCTION FOR HYPERSONIC VEHICLES

The structural problems of re-entry occasioned by aerodynamic heating are now generally well known. Typical of these heating problems is the environment experienced by the manned lifting vehicle re-entering from a low altitude orbit. Figure 1 shows typical curves of lower surface temperature as a function of time for a wing loading of 25 Ibs/ft(exp 2), and a lift-drag ratio of 2.5. The two curves cover a practical range of re-entry angles, the lower curve representing an ideal re-entry path with zero dive angle and the upper curve assuming a 2° error in the re-entry angle. Maneuvers for course change or correction are also added to the upper curve. Significant factors from this curve are the relationship between the maximum temperatures and the capabilities of available metallic material, and also the long re-entry time and its effect on total heat load. If a very shallow re-entry is made, maximum lower surface temperatures reach 2000°F which is just within the range of conventional superalloys. To accommodate practical re-entry angles and maneuvers, however, the temperature capability must reach about 2500°F which requires refractory metals. The re-entry time may be as high as 100 minutes, which gives total heat loads of approximately 40,000 BTU/ft(exp 2). A heat load of this magnitude, with equilibrium surface temperatures of the values shown, suggests that a lighter airframe can be constructed by dissipating the heat by radiation from the surface, rather than by absorbing it with a heat sink, or surface cooling, or ablation. Air Force programs to provide airframes for this type of environment have involved the parallel development of a number of different structural concepts. The development to be discussed here was carried out by Bell Aerosystems Company for the Fabrication Branch, Manufacturing Technology Laboratory, Directorate of Materials and Processes, Aeronautical Systems' Division, Wright-Patterson Air Force Base, Ohio, under Contract AF33(600)-40100 (Double-Wall Cooled Structure).

Reentry vehicle↗