Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LiP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Comparison of predicted and measured low-speed performance of two 51 centimeter-diameter inlets at incidence angle

Theoretical and experimental internal flow characteristics of two 51-cm-diameter inlets are compared. Theoretical flow characteristics along the inlet surface were obtained from an axisymmetric potential flow and boundary layer analysis. The experimental data were obtained from low-speed tests of a high-bypass-ratio turbofan engine simulator. Comparisons between calculated internal surface pressure distributions and experimental data are presented for a free-system velocity of 45 m/sec and for incidence angles from 0 deg to 50 deg. Analysis of boundary layer separation on the inlet lip at incidence angle is the major emphasis of this report. Theoretical boundary layer shape factors, skin friction coefficients, and velocity profiles in the boundary layer are presented, along with the location of the transition region. Theoretical and experimental separation locations are also discussed.

Albers, J. A.↗
NASA NTRS1974

Sonic inlet noise attenuation and performance with a J-85 turbojet engine as a noise source

A static test program was conducted to investigate aerodynamic and acoustic performance of a sonic inlet used as a noise suppressor. A translating centerbody type inlet with radial vanes was tested ahead of a J85-GE-13 turbojet engine. The inlet when fully choked, maintained high recovery with low distortions while dramatically reducing noise emanating from the compressor. Recoveries of 98.1% at simulated takeoff and 95% at approach were attained with associated sound attenuation of 40 db and 38 db respectively. Inlet lip shape was found to have significant effects on noise attenuation at these static conditions.

Groth, H. W.↗
NASA NTRS1974

Metering gun for dispensing precisely measured charges of fluid

A cyclically operable fluid dispenser for use in dispensing precisely measured charges of potable water aboard spacecraft is described. The dispenser is characterized by (1) a sealed housing adapted to be held within a crewman's palm and coupled with a pressurized source of potable water; (2) a dispensing jet projected from the housing and configured to be received within a crewman's lips; (3) an expansible measuring chamber for measuring charges of drinking water received from the source; (4) and a dispenser actuator including a lever extended from the housing to be digitated for initiating operational cycles, whereby precisely measured charges of potable water selectively are delivered for drinking purposes in a weightless environment.

Cook, T. A.↗
NASA NTRS1974

Effects of the six engine air breathing propulsion system on space shuttle orbiter subsonic stability and control characteristics

Experimental aerodynamic investigations were conducted on a 0.0405 scale representation of the -89B space shuttle orbiter in the 7.75 x 11.00 foot low speed wind tunnel during the time period September 4 - 14, 1973. The primary test objective was to optimize the air breathing propulsion system nacelle cowl-inlet design and to determine the aerodynamic effects of this design on the orbiter stability and control characteristics. Nacelle cowl-inlet optimization was determined from total pressure - static pressure measurements obtained from pressure rakes located in the left hand nacelle pod at the engine face station. After the optimum cow-inlet design, consisting of a 7 deg cowl lip angle, short cowl, 7 deg short diverter, and a nacelle toe-in angle of 5 deg was selected, the aerodynamic effects of various locations of this design were investigated. The 3 pod - 6 Nacelle configuration was tested both underwing and overwing in three different longitudinal locations. Orbiter control effectiveness, both with and without Nacelles, was investigated at elevon deflections of 0 deg, -10 deg and +15 deg and at aileron deflections of 0 deg and +10 deg about 0 deg elevon.

Mennell, R. C.↗
NASA NTRS1974

Boundary-layer analysis of subsonic inlet diffuser geometries for engines nacelles

Theoretical Mach number distributions and boundary-layer parameters are presented for subsonic nacelle inlet diffuser geometries with length to exit diameter ratios ranging from 0.4 to 1.6 and diffuser exit area to throat area ratios ranging from 1.1 to 2.0. The major portion of the study was done with a cubic diffuser contour with the inflection point at the midpoint of the diffuser, a diffuser throat Mach number of 0.6, and a free-stream Mach number of 0.12. Calculations were performed at both model (diffuser exit diameter, 30.5 cm) and full-scale (diffuser exit diameter, 183 cm) sizes. Separation limits were defined by establishing a separation boundary on plots of diffuser area ratio as a function of diffuser length to diameter ratio. The effects of diffuser contour, inlet lip geometry, and throat Mach number on the boundary-layer characteristics are illustrated. The major results of the study indicate that the separation boundary is shifted to greater area ratios by (1) increasing the diffuser length, (2) increasing the scale of the diffuser and, (3) moving the inflection point of the diffuser contour to or ahead of the midpoint of the diffuser.

Albers, J. A.↗
NASA NTRS1974

The 727 airplane side inlet low-speed performance confirmation model test for refanned JT8D engines

The results of a low-speed wind tunnel test of a 0.3 scale model 727 airplane side inlet for JT8D-100 engines are presented. The objectives of the test were to develop lines for a full-scale flightworthy inlet, to evaluate inlet total pressure recovery and steady-state total pressure distortion, and to obtain model-scale distortion data which can be used in the assessment of the compatibility of the inlet with the JT8D-100 series engines. A secondary objective was to obtain internal/external cowl static pressures for the determination of nacelle loads. Two basic inlet models were tested at static, forward speed, angle-of-attack (inflow angle), and cross-wind conditions. One model was with and one without an acoustic ring. Two modifications to the models were also tested, one with the ring closer to the inlet throat and one with a larger lip. Test measurements consisted of inlet surface static pressure, engine face total pressure, inlet airflow, tunnel total pressure, tunnel total temperature and tunnel velocity. Total pressure traverses were taken directly behind the ring and strut. No dynamic measurements were taken.

Schuehle, A. L.↗
NASA NTRS1974

Effect of the six engine air breathing propulsion system on space shuttle orbiter subsonic and transonic stability and control characteristics (OA91)

Experimental aerodynamic investigations were conducted on a 0.015 scale representation (Model 42-0) of the VL70-000139B space shuttle orbiter configuration. The test objective was to determine the effect of three air breathing propulsion system ferry/flight test configurations on the transonic drag rise, the elevon effectiveness, the longitudinal stability, and the lateral-directional stability of the -139B shuttle orbiter. The model was sting mounted on a Task 1.5 inch internal strain gage balance, and six-component aerodynamic force and moment data were recorded over an angle of attack range of minus 3 deg to 14 deg at Mach numbers of 0.5, 0.6, 0.7, 0.8, and 0.9 with a Reynolds number of 6.4 million/ft. Data were also recorded at a sides lip angle of five degrees.

Smith, H. C.↗
NASA NTRS1974

Low-speed wind tunnel tests of a 50.8-centimeter (20-in.) 1.15-pressure-ratio fan engine model

At a typical STOL aircraft takeoff and landing velocity, wind tunnel aerodynamic and acoustic measurements demonstrated that an inlet lip-area contraction ratio of 1.35 was superior to a ratio of 1.26 at high incidence angles. A 17 percent reduction in net thrust and an increase of 9 decibels in sound pressure level at the blade passing frequency resulted from inlet flow separation at an incidence angle of 50 deg with the 1.26-contraction-ratio inlet. Reverse-thrust forces obtained with blade rotation through the feathered angle were 1.8 times larger than with blade rotation through the flat angle. Reverse-thrust force was reduced from 30 to 50 percent and sound pressure level increased from 3 to 7 decibels at the blade passing frequency between the wind-tunnel-off condition and a typical STOL aircraft landing velocity.

Wesoky, H. L.↗
NASA NTRS1974

Research on the elastic stability of large shells

Tests were conducted to determine the elastic stability of large shell structures. The configuration of the shells and the instrumentation used in the measurements are described. The testing procedures are explained. Results of the stress analysis are plotted in polar graph form to show the areas of strain in micro inches at the outer surface of the skin and the inner lip of the stringer.

Horton, W. H.↗
NASA NTRS1973

Wind tunnel tests of a 20 inch diameter 1.15 pressure ratio fan engine model

Aerodynamic and acoustic measurements at a typical STOL aircraft takeoff and landing velocity demonstrated that a 1.35 inlet lip area contraction ratio was superior to a 1.26 ratio at high nacelle incidence angles. Reverse thrust, obtained with a variable pitch rotor, was lower at the landing velocity, and the noise level higher, than at the static condition. High speed tests showed that, for the design cruise Mach number of 0.75, internal losses and external drag were 27 per cent of the ideal fan net thrust, and propulsive efficiency was estimated to be 59 per cent for an 85 per cent efficient fan stage. For comparison, a similar 1.55 pressure ratio fan system would have a propulsive efficiency of 62 per cent.

Wesoky, H. L.↗
NASA NTRS1974

Investigation of the three-dimensional turbulent flow downstream of swept slot injection in hypersonic flow

Results of an experimental and numerical investigation of tangential swept slot injection (sweep angles of 22.5 and 45 deg) into a thick turbulent boundary layer at Mach 6 are presented. Film cooling effectiveness, skin friction, and flow structure downstream of the swept slot injection are investigated. The data are compared to that for unswept slots, and it is found that cooling effectiveness and skin-friction reductions are not significantly affected by sweeping the slot. Predictions of cooling effectiveness and skin friction obtained by a numerical finite-difference technique agree reasonably well with experimental surface variables. As in previous supersonic two-dimensional slot research, reduced mixing was found downstream of the slot lip in the present three-dimensional case.

Hefner, J. N.↗
NASA NTRS1975

Design criteria monograph on transmission seals

Guide is based on experience obtained in wide variety of applications using lip, circumferential, and face seals. Particular attention is given to capabilities and lubrication of various seal types. Special limitations as a result of storage requirements, quality control, installation, operation, and removal are discussed.

Hayden, T. S.↗
NASA NTRS1974

Identification characteristics of certain lunar relief forms on pictures obtained from spacecraft

This investigation was restricted to the determination of recognitional characteristics of a single type of relief form, dimple craters on the surface of maria. These craters were arbitrarily considered as closed, negative relief forms, circular in plan-view, and symmetric relative to the center. Two techniques were used to determine the shadow configuration in the craters: (1) experimental determination of the shadow edge by illuminating the models of different profile shapes with a parallel light beam; and (2) geometric construction of the shadow edge using a vertical section of the formation in the direction of the solar rays. A morphological map of the surface which includes the following factors can be compiled using the proposed identification technique: crater profile nature, crater diameter, ratio of diameter and depth, sharpness of the lip, and distribution density of the forms.

Kravtsova, V. I.↗
NASA NTRS1975

Analysis of noise produced by jet impingement near the trailing edge of a flat and a curved plate

The sound fields produced by the interaction of a subsonic cold gas jet with the trailing edge of a large flat plate and a curved plate were analyzed. The analyses were performed to obtain a better understanding of the dominant noise source and the mechanism governing the peak sound-pressure-level frequencies of the broadband spectra. An analytical expression incorporating an available theory and experimental data predicts sound field data over an arc of approximately 105 deg measured from the upstream jet axis for the two independent sets of data. The dominant noise as detected on the impingement side of either plate results from the jet impact (eighth power of the velocity dependence) rather than a trailing-edge disturbance (fifth or sixth power of the velocity dependence). Also, the frequency of the peak SPL may be governed by a phenomenon which produces periodic formation and shedding of ring vortices from the nozzle lip.

Mckinzie, D. J., Jr.↗
NASA NTRS1975

Comparison of experimental and theoretical boundary-layer separation for inlets at incidence angle at low-speed conditions

Comparisons between experimental and theoretical Mach number distributions and separation locations are presented for the internal surfaces of four different subsonic inlet geometries with exit diameters of 13.97 centimeters. The free stream Mach number was held constant at 0.127, the one-dimensional throat Mach number ranged from 0.49 to 0.71, and the incidence angle ranged from 0 deg to 50 deg. Generally good agreement was found between the theoretical and experimental surface Mach number distributions as long as no flow separation existed. At high incidence angles, where separation was obvious in the experimental data, the theory predicted separation on the lip. At lower incidence angles, the theoretical results indicated diffuser separation which was not obvious from the experimental surface Mach number distributions. As incidence angle was varied from 0 deg to 50 deg, the predicted separation location shifted from the diffuser region to the inlet highlight. Relatively small total pressure losses were obtained when the predicted separation location was greater than 0.6 of the distance between the highlight and the diffuser exit.

Felderman, E. J.↗
NASA NTRS1974

Wind tunnel test of model target thrust reversers for the Pratt and Whitney aircraft JT8D-100 series engines installed on a 727-200 airplane

The results of a low speed wind tunnel test of 0.046 scale model target thrust reversers installed on a 727-200 model airplane are presented. The full airplane model was mounted on a force balance, except for the nacelles and thrust reversers, which were independently mounted and isolated from it. The installation had the capability of simulating the inlet airflows and of supplying the correct proportions of primary and secondary air to the nozzles. The objectives of the test were to assess the compatibility of the thrust reversers target door design with the engine and airplane. The following measurements were made: hot gas ingestion at the nacelle inlets; model lift, drag, and pitching moment; hot gas impingement on the airplane structure; and qualitative assessment of the rudder effectiveness. The major parameters controlling hot gas ingestion were found to be thrust reverser orientation, engine power setting, and the lip height of the bottom thrust reverser doors on the side nacelles. The thrust reversers tended to increase the model lift, decrease the drag, and decrease the pitching moment.

Hambly, D.↗
NASA NTRS1975

Experimental evaluation of a Mach 3.5 axisymmetric inlet

Wind tunnel test results for a large scale inlet model designed for Mach 3.5 are presented and compared with analytical predictions. The inlet is an axisymmetric mixed-compression type with a lip diameter of 49.723 cm. The inlet design was developed using analytical procedures. Data are shown for freestream Mach numbers from 0.6 to 3.5. The test results indicate that boundary layer bleed requirements can be accurately predicted. Good agreement was obtained with analytical predictions of the flowfield structure and boundary layer development in the supersonic diffuser yielding high performance at the design Mach number. The highest engine face total pressure recovery at Mach 3.5 was 85.8%; this was obtained at 0.05 Mach tolerance with only 2.8% total pressure distortion and 13.4% bleed. In the started Mach number range from 1.6 to 3.5, the total pressure recovery in the throat, downstream of the terminal normal shock, ranged between 91% and 95%. Total pressure losses in the subsonic diffuser varied from 3% to 13%. The higher losses occuring between Mach 2.5 and 3.2 were believed to be caused by the rapid rate of increase in the area of the diffuser just downstream of the throat, possibly coupled with inadequate centerbody throat bleed. In the unstarted mode at transonic speeds, the maximum inlet flow was over 99% of the theoretical maximum capture mass-flow.

Syberg, J.↗
NASA NTRS1975

Development of circumferential seal for helicopter transmissions: Results of bench and flight tests

A modified circumferential segmented ring seal was designed for direct replacement of a helicopter transmission elastomeric lip seal operating on a shaft diameter of 13.91 centimeters (5.481 in.) at sliding velocities to 52.48 m/sec (10 330 ft/min). The modifications involved the garter spring tension, shaft roundness, seal housing flatness, and pumping grooves to inhibit leakage. Operation of the seals in bench tests under simulated helicopter transmission conditions revealed that the seal leakage rate was within acceptable limits and that the wear rate was negligible. The low leakage and wear rates were confirmed in flight tests of 600 and 175 hours (sliding speed, 48.11 m/sec (9470 ft/min)). An additional 200 hours of air worthiness qualification testing (aircraft tie down) demonstrated that the seal can operate at the advanced sliding conditions of 52.48 m/sec (10 330 ft/min).

Strom, T. N.↗