Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Li plating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Operating the Upgraded NSTX HHFW Antenna Array in an Environment with Li-coated Surfaces

The single-feed, end-grounded straps of the NSTX 12-strap HHFW antenna array have been replaced with double-feed, center-grounded straps to reduce the voltages in the vicinity of the Faraday shield (FS) for a given strap current. The strap spacings to the FS and to the back plate were increased by 3 mm to decrease the electric fields for a given voltage. The electric fields near the FS have been roughly halved for the same strap currents, permitting a direct examination of the roles that internal fields play in determining antenna power limits in plasmas. Extensive RF/plasma conditioning of the antenna was required to remove enough of the evaporated Li deposits from prior wall conditioning to permit coupling in excess of 4 MW to L- and H-mode plasmas in 2009. Most arcs were associated with expulsion of Li from the FS/antenna frame surfaces. The center-grounded straps were less susceptible to arcing during ELMing Hmode plasmas. Reliable operation above 2 MW was difficult after the installation of the Liquid Lithium Divertor (LLD) in 2010. Li-compound dust was found in the antennas after this run and is believed to have contributed to the reduced power limit.

RF Heating and Current Drive↗

Detecting lithium plating dynamics in a solid-state battery with operando X-ray computed tomography using machine learning

Operando X-ray micro-computed tomography (µCT) provides an opportunity to observe the evolution of Li structures inside pouch cells. Segmentation is an essential step to quantitatively analyzing µCT datasets but is challenging to achieve on operando Li-metal battery datasets due to the low X-ray attenuation of the Li metal and the sheer size of the datasets. Herein, we report a computational approach, batteryNET, to train an Iterative Residual U-Net-based network to detect Li structures. The resulting semantic segmentation shows singular Li-related component changes, addressing diverse morphologies in the dataset. In addition, visualizations of the dead Li are provided, including calculations about the volume and effective thickness of electrodes, deposited Li, and redeposited Li. We also report discoveries about the spatial relationships between these components. The approach focuses on a method for analyzing battery performance, which brings insight that significantly benefits future Li-metal battery design and a semantic segmentation transferrable to other datasets.

25 ENERGY STORAGE↗

In Situ Observation of Acicular Ferrite Nucleation and Growth at Different Cooling Rate in Ti-Zr Deoxidized Steel

The effects of cooling rate on acicular ferrite (AF) nucleation, growth, and inclusion characteristics in Ti-Zr deoxidation steel were studied by utilizing the high temperature confocal laser scanning microscope (HT-CLSM). The results indicated that with the increase of cooling rate, the ferrite start nucleation temperature decreased, and the difference of first nucleation temperature between AF and ferrite side plate (FSP) reduced. When the cooling rate increased to 10.0 °C/s, AF and FSP simultaneously nucleated at 564.5 °C. In addition, the AF actual growth rate rose with the increase of cooling rate and reached 30.13 µm/s at 10.0 °C/s cooling rate. The AF ratio in microstructure increased first and then decreased with the cooling rate increase and was up to the maximum 45.83 pct at 1.0 °C/s cooling rate. For inclusion characteristics, cooling rates had no obvious effect on inclusion types, but had a great influence on inclusions size distribution. With the cooling rate increase, the inclusion average diameter reduced, and diminished to 1.39 µm at 10.0 °C/s cooling rate. Finally, the AF nucleation on the Ti-Zr-Mn-O-S + TiN inclusion could be explained by the low lattice misfit between ferrite and TiN that precipitated on the Ti-Zr-Mn-O-S inclusion surface.

36 MATERIALS SCIENCE↗

Stress evolution in lithium metal electrodes

The potential advantages of lithium metal anodes have received widespread attention (highest capacity, lowest reduction potential, etc). However, the poor stability of Li metal / liquid electrolyte interfaces leads to chronic problems, such as dendrite formation and capacity loss. The possible impact of mechanical effects on interface stability and dendrite formation are difficult to probe directly. In this study, stress evolution during lithium plating and stripping was monitored with precise in situ measurements. The data obtained with different film thicknesses made it possible to separate the stresses associated with the lithium metal and the solid electrolyte interphase (SEI). The results show that significant stresses are created in the SEI films. Based on this, a basic model of wrinkling-ratcheting-delamination is also presented. This analysis indicates that plasticity in a growing Li film can enhance surface wrinkling, and thus lead to morphological destabilization of a planar growth front.

25 ENERGY STORAGE↗

Stabilizing effect of resistivity towards ELM-free H-mode discharge in lithium-conditioned NSTX

Linear stability analysis of the national spherical torus experiment (NSTX) Li-conditioned ELM-free H-mode equilibria is carried out in the context of the extended magneto-hydrodynamic (MHD) model in NIMROD. Our purpose is to investigate the physical cause behind edge localized mode (ELM) suppression in experiment after the Li-coating of the divertor and the first wall of the NSTX tokamak. Besides ideal MHD modeling, including finite-Larmor radius effect and two-fluid Hall and electron diamagnetic drift contributions, a non-ideal resistivity model is employed, taking into account the increase of Z eff after Li-conditioning in ELM-free H-mode. And unlike an earlier conclusion from an eigenvalue code analysis of these equilibria, NIMROD results find that after reduced recycling from divertor plates, profile modification is necessary but insufficient to explain the mechanism behind complete ELMs suppression in ideal two-fluid MHD. After considering the higher plasma resistivity due to higher Z eff, the complete stabilization could be explained. Furthermore, a thorough analysis of both pre-lithium ELMy and with-lithium ELM-free cases using ideal and non-ideal MHD models is presented, after accurately including a vacuum-like cold halo region in NIMROD to investigate ELMs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Joining Study for Formed Plate Heat Exchangers (Final Report)

Plate heat exchangers (PHEs) have been used in numerous industrial applications, such as HVAC systems, power generation, transportation and manufacturing. The performance of plate heat exchangers is frequently undermined by corrosion, fouling, and scaling. These phenomena not only diminish heat transfer efficiency but also lead to increased operational costs, maintenance demands, and reduced equipment lifespan. In this project, the team addressed the widespread challenges of corrosion, fouling, and scaling, and explored alternative material solutions. While commonly used materials like stainless steel and titanium offer notable benefits, they can still experience corrosion under certain operating conditions. The advancement of new materials and surface engineering technologies, such as advanced coating, ceramics, composites materials, and high entropy alloys are promising for can help solve these issues, enable longer lifetime and high performance of plate heat exchangers.

36 MATERIALS SCIENCE↗

Ultrafast inorganic scintillator-based front imager for Gigahertz Hard X-ray imaging

State-of-the art X-ray imaging cameras using silicon sensors for X-ray detection have demonstrated a frame-rate of 10 MHz and excellent performance for X-ray energies below 20 keV. We proposed a pixelated ultrafast inorganic scintillator-based front imager for GHz hard X-ray imaging. Here, the proposed imager is featured with a total absorption for hard X-ray photons, and provides sub-ns scintillation pulse width crucial for X-ray bunches of a few ns spacing foreseen at the proposed MaRIE facility. We measured temporal response of a dozen ultrafast and fast inorganic scintillators at the 10-ID-B site of the Advanced Photon Source (APS) of ANL. Crystal's response to hybrid X-ray beam of 30 keV, consisting of singlet bunches of 50 ps width and septuplet bunches of 27 ps width with 2.83 ns bunch spacing, was measured. Ultrafast inorganic scintillators, such as BaF 2 :Y and ZnO:Ga, show clearly resolved X-ray bunches for septuplets, as well as no degradation of amplitude for continuous eight septuplets, providing a proof of principle for the ultrafast inorganic scintillator-based total absorption front imager for the proposed MaRIE project.

47 OTHER INSTRUMENTATION↗

High Li + Transference Number Electrolyte Enabled by Fluoride Acceptor for Low-Temperature Li-Ion Batteries

To enable wide-temperature operation of lithium-ion batteries (LIBs), new electrolyte formulations have been developed to enhance the performance, particularly at low temperatures. A key challenge lies in achieving both high ionic conductivity and a high lithium-ion transference number due to their inherent trade-off. In this study, we designed an electrolyte system comprising tris(pentafluorophenyl)borane (TPFPB), a fluoride acceptor, and LiF salt in ethylene carbonate (EC)-free solvents. TPFPB, with its electron-deficient boron center, facilitates fluoride transfer reactions that promote the dissociation of otherwise insoluble LiF. When methyl acetate (MA) was used as the solvent, the electrolyte exhibited a high transference number (t Li + = 0.85) and ionic conductivity (σ = 5.0 × 10 –3 S cm –1 ). The optimized electrolyte demonstrated excellent performance at −20 °C, with no evidence of lithium plating. This work presents a new strategy for electrolyte design by leveraging cation desolvation to achieve high-performance LIBs for low-temperature and high-power applications.

anions↗

A layered Prussian blue analogue as fast-charging negative electrode material for lithium-ion batteries

The simultaneous achievement of fast-charging and high specific capacity remains a critical challenge for lithium-ion battery negative electrodes. Here we report a layered manganese-based Prussian blue analogue, synthesized through vacancy control and subsequent thermal transformation. As a conversion-type negative electrode, this material exhibits high-rate performance, delivering a specific capacity of 510 mAh g −1 at a specific current of 8 A g −1 , and operates at a moderate average voltage of approximately 1.2 V vs. Li/Li + , which mitigates lithium plating risks. This high-rate capability stems from the analogue’s specific linkage configurations, which facilitate a high content of active transition metal and strong Li+ adsorption at nitrogen sites. The high transition metal content enables a high reversible capacity, while strong Li + adsorption promotes an efficient initial crystalline-to-amorphous transformation. This process induces dynamically reversible component migration during subsequent cycling, thereby enhancing conversion reaction kinetics. Our findings provide insights into the application of Prussian blue analogues as fast-charging negative electrode materials. The development of fast-charging and high-capacity negative electrodes is critical for advanced lithium-ion batteries. Here, authors use a vacancy engineering strategy to develop a layered Prussian blue analogue with competitive rate capability, delivering a specific capacity of 510 mAh g −1 at a specific current of 8 A g −1 .

25 ENERGY STORAGE↗

Control of the Plasma-Material Interface for Long Pulse Optimization in EAST and KSTAR

This is the Final Technical Report for the Grant DE-SC0016322. The major goals of the project are to use HIDRA to evaluate and optimize the FLiLi and LiMIT concepts, in preparation for the final designs of liquid Li PFCs for testing in EAST long pulse discharges. In the first year the goal is to fully commission HIDRA and begin liquid Li tests. In the second year it is to test the FLiLi and LiMIT designs in HIDRA and start the production of the first LiMIT test plate for EAST.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Optical stress sensor based on electro-optic compensation for photoelastic birefringence in a single crystal

An optical stress sensor is proposed by using a single crystal with both electro-optic and photoelastic effects. Different from previous crystal-based stress sensors, the proposed sensor is based on electro-optic compensation for stress-induced birefringence and does not need an additional quarter-wave plate or modulator, because the stress-sensing element is simultaneously used as an electro-optic compensator. Candidate sensing materials include electro-optic crystals of the 3 m symmetry group and all glass with large Kerr coefficients. A primary experiment has demonstrated that the stress-induced birefringence in lithium niobate crystal can be compensated by its electro-optic birefringence. The proposed stress sensor is compact and low cost, and it is possible to achieve closed-loop stress measurement.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

In Situ and Operando Observation of Zinc Moss Growth and Dissolution in Alkaline Electrolyte for Zinc–Air Batteries

As a promising battery technology, zinc–air batteries still face significant challenges, including the formation of a mossy structure on the zinc metal anode in alkaline electrolyte. Because a similar phenomenon also plagues lithium and sodium metal batteries, elucidating its mechanism has important implications for progress in energy storage. Herein, operando X-ray nanotomography was employed to visualize zinc moss growth and dissolution at the individual colony level. By tracking its microstructure evolution, zinc moss was found to display irreversible plating/stripping behavior. While zinc moss exhibits self-limiting growth and zinc deposition occurs mainly in its outer region, zinc dissolution is more uniformly distributed inside the moss colony upon stripping, leading to the formation of “dead” zinc and capacity loss. A direct correlation is established between the moss amount and zinc plating/stripping efficiency. Finally, results from this study offer new insights into mitigating the unstable zinc plating morphology and improving the cycle life of aqueous zinc–air batteries.

36 MATERIALS SCIENCE↗

Elucidating the structure of the magnesium aluminum chloride complex electrolyte for magnesium-ion batteries

Non-aqueous Mg-ion batteries offer a promising way to overcome safety, costs, and energy density limitations of state-of-the-art Li-ion battery technology. Here, we present a rigorous analysis of the magnesium aluminum chloride complex (MACC) in tetrahydrofuran (THF), one of the few electrolytes that can reversibly plate and strip Mg. We use ab initio calculations and classical molecular dynamics simulations to interrogate the MACC electrolyte composition with the goal of addressing two urgent questions that have puzzled battery researchers: (i) the functional species of the electrolyte, and (ii) the complex equilibria regulating the MACC speciation after prolonged electrochemical cycling, a process termed as conditioning, and after prolonged inactivity, a process called aging. A general computational strategy to untangle the complex structure of electrolytes, ionic liquids and other liquid media is presented. The analysis of formation energies and grand-potential phase diagrams of Mg–Al–Cl–THF suggests that the MACC electrolyte bears a simple chemical structure with few simple constituents, namely the electro-active species MgCl + and AlCl 4 - in equilibrium with MgCl 2 and AlCl 3 . Knowledge of the stable species of the MACC electrolyte allows us to determine the most important equilibria occurring during electrochemical cycling. We observe that Al deposition is always preferred to Mg deposition, explaining why freshly synthesized MACC cannot operate and needs to undergo preparatory conditioning. Similarly, we suggest that aluminum displacement and depletion from the solution upon electrolyte resting (along with continuous MgCl 2 regeneration) represents one of the causes of electrolyte aging. Finally, we compute the NMR shifts from shielding tensors of selected molecules and ions providing fingerprints to guide future experimental investigations.

25 ENERGY STORAGE↗

Manufacturing Oxide Dispersion Strengthened (ODS) steel plate via cold spray and friction stir processing

Oxide dispersion strengthened (ODS) steels, traditionally fabricated by ball milling and conventional powder metallurgy techniques to achieve bulk form, followed by intricate rolling and thermal treatment steps to achieve plate or sheet form. Here, we present a novel processing route that combines cold spray (CS) with friction stir processing (FSP) to manufacture ODS steel plate directly from gas atomization reaction synthesis (GARS)-prepared powder, thus no rolling steps involved. Microstructural and mechanical characterizations were performed to assess the quality and properties of the resulting ODS steel plate. Our findings demonstrate that the slightly porous CS deposited layer was fully consolidated after FSP, yielding a fully dense ODS steel plate that exhibited a favorable tradeoff between strength and ductility upon extraction from the substrate. Furthermore, through microstructural analysis, we revealed the presence of an appreciable density (∼10 22 /m 3 ) of nano-sized oxide particles, with the majority being smaller than 5 nm via the combined CS + FSP fabrication route. This work serves as a first proof-of-concept demonstration of the manufacturing approach described herein, offering a possible alternative route for producing ODS steel plates.

36 MATERIALS SCIENCE↗

Metal-Assisted Chemical Etching and Electroless Deposition for Fabrication of Hard X-ray Pd/Si Zone Plates

Zone plates are diffractive optics commonly used in X-ray microscopes. Here, we present a wet-chemical approach for fabricating high aspect ratio Pd/Si zone plate optics aimed at the hard X-ray regime. A Si zone plate mold is fabricated via metal-assisted chemical etching (MACE) and further metalized with Pd via electroless deposition (ELD). MACE results in vertical Si zones with high aspect ratios. The observed MACE rate with our zone plate design is 700 nm/min. The ELD metallization yields a Pd density of 10.7 g/cm 3 , a value slightly lower than the theoretical density of 12 g/cm 3 . Fabricated zone plates have a grid design, 1:1 line-to-space-ratio, 30 nm outermost zone width, and an aspect ratio of 30:1. At 9 keV X-ray energy, the zone plate device shows a first order diffraction efficiency of 1.9%, measured at the MAX IV NanoMAX beamline. With this work, the possibility is opened to fabricate X-ray zone plates with low-cost etching and metallization methods.

36 MATERIALS SCIENCE↗

Results from a new flowing liquid Li limiter with TZM substrate during high confinement plasmas in the EAST device

A third generation flowing liquid lithium (FLiLi) limiter with a substrate made of TZM, an alloy with >99% Mo, was fabricated by conventional manufacturing techniques. TZM has a high corrosion resistance, a high sputtering threshold, and a good wettability to Li, as compared to stainless steel (SS), which had been used as an FLiLi substrate surface in 2014 and 2016. The third generation FLiLi was inserted into the edge in EAST H-mode plasmas in an upper single-null configuration with an ion grad-B drift toward the upper divertor with a limiter temperature of 330–380 °C and an auxiliary heating power of about 2–8 MW. Analysis has shown that by using TZM FLiLi, fuel particle recycling continuously decreased and near-complete edge localized mode elimination was achieved in H-mode plasmas with RF-only heating. The main impurities during the initial FLiLi discharges were Mo, Fe, and W resulting from strong plasma interaction at the Mo plate side, the SS collector, and the upper W divertor. Plasma stored energy increased by about 10 kJ in subsequent FLiLi discharges due to decreased impurity radiation. Engineering analysis shows a uniform lithium flow with an ~80% Li coverage ratio on the limiter surface, similar to the second FLiLi, even though only one of two J × B pumps was functioning. Despite technical difficulties, the FLiLi gen.3 improved the overall plasma performance, providing support for flowing liquid Li plasma facing component applications in present and future devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗