Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Instrumentation Set Points”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Instrument to average 100 data sets

An instrumentation system is currently under development which will measure many of the important parameters associated with the operation of an internal combustion engine. Some of these parameters include mass-fraction burn rate, ignition energy, and the indicated mean effective pressure. One of the characteristics of an internal combustion engine is the cycle-to-cycle variation of these parameters. A curve-averaging instrument has been produced which will generate the average curve, over 100 cycles, of any engine parameter. the average curve is described by 2048 discrete points which are displayed on an oscilloscope screen to facilitate recording and is available in real time. Input can be any parameter which is expressed as a + or - 10-volt signal. Operation of the curve-averaging instrument is defined between 100 and 6000 rpm. Provisions have also been made for averaging as many as four parameters simultaneously, with a subsequent decrease in resolution. This provides the means to correlate and perhaps interrelate the phenomena occurring in an internal combustion engine. This instrument has been used successfully on a 1975 Chevrolet V8 engine, and on a Continental 6-cylinder aircraft engine. While this instrument was designed for use on an internal combustion engine, with some modification it can be used to average any cyclically varying waveform.

Tuma, G. B.↗

Gamma-Ray Point-Source Localization and Sparse Image Reconstruction using Poisson Likelihood

Gamma-ray imaging trys to reconstruct the spatial and intensity distribution of gamma-emitting radionuclides from a set of measurements. Wholly, this problem is solved by discretizing the spatial dimensions and employing the maximum likelihood expectation maximization (ML-EM) algorithm, with or without some form of regularization. While the generality of this formulation enables use in a wide variety of scenarios, it is susceptible to overfitting, limited by the discretization of spatial coordinates, and can be computationally expensive. We present a novel approach to 3D gamma-ray image reconstruction for scenarios where sparsity may be assumed, for example radiological source search. In this work we first formulate a point-source localization (PSL) approach as an optimization problem where both position and source intensity are continuous variables. We then extend and generalize this formulation to an iterative algorithm called additive point-source localization (APSL) for sparse parametric image reconstruction. A set of simulated source search scenarios using a single non-directional detector are considered, finding improved image accuracy and computational efficiency with APSL over traditional grid-based methods.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Evaluation of Minimum Detectable Activities for Stack Sample Analyses

The Rad-NESHAP program takes samples at major point sources to track how much of select nuclides are being emitted out of the stack. Samples are taken at the site where the radiological operations are being performed. The samples are then sent to analytical laboratories for analysis to determine what nuclides exist in the sample. However, due to the sensitivity of the instruments, false positives are often reported. To reduce the number of false positives, the results reported from the analytical labs are compared to set detection limits. Anything below the set detection limit is considered part of the background while anything above the limit is considered a positive hit. Therefore, the detection limit must be set low enough that any false negatives do not result in a significant dose missed at the end of the year but high enough that there are not enough false positives to skew the annual dose being reported. All detection limits listed in this section for the analyses below were designed to meet the stated equivalent emissions rate and subsequent off-site doses. These minimum detectable activities (MDAs) were developed in the 1990s and documented in the memo cited for each analysis below. These limits and memos are all currently referenced in the Quality Assurance Project Plan (QAPP) for the Rad-NESHAP Compliance Task, which is being updated to a Project Implementation Plan (PIP) concurrently with this document. As part of this update process, the original MDAs defined in this section needed to be verified that they were still conservative and meet the off-site dose levels stated.

2019 MDA↗

Validation and Improvement of SRTM Performance over Rugged Terrain

We have previously reported work related to basic technique development in phase unwrapping and generation of digital elevation models (DEM). In the final year of this work we have applied our technique work to the improvement of DEM's produced by SRTM. In particular, we have developed a rigorous mathematical algorithm and means to fill in missing data over rough terrain from other data sets. We illustrate this method by using a higher resolution, but globally less accurate, DEM produced by the TOPSAR airborne instrument over the Galapagos Islands to augment the SRTM data set in this area, We combine this data set with SRTM to use each set to fill in holes left over by the other imaging system. The infilling is done by first interpolating each data set using a prediction error filter that reproduces the same statistical characterization as exhibited by the entire data set within the interpolated region. After this procedure is implemented on each data set, the two are combined on a point by point basis with weights that reflect the accuracy of each data point in its original image. In areas that are better covered by SRTM, TOPSAR data are weighted down but still retain TOPSAR statistics. The reverse is true for regions better covered by TOPSAR. The resulting DEM passes statistical tests and appears quite feasible to the eye, but as this DEM is the best available for the region we cannot fully veri@ its accuracy. Spot checks with GPS points show that locally the technique results in a more comprehensive and accurate map than either data set alone.

Zebker, Howard A.↗

Einstein Inflationary Probe (EIP)

I will discuss plans to develop a concept for the Einstein Inflation Probe: a mission to detect gravity waves from inflation via the unique signature they impart to the cosmic microwave background (CMB) polarization. A sensitive CMB polarization satellite may be the only way to probe physics at the grand-unified theory (GUT) scale, exceeding by 12 orders of magnitude the energies studied at the Large Hadron Collider. A detection of gravity waves would represent a remarkable confirmation of the inflationary paradigm and set the energy scale at which inflation occurred when the universe was a fraction of a second old. Even a strong upper limit to the gravity wave amplitude would be significant, ruling out many common models of inflation, and pointing to inflation occurring at much lower energy, if at all. Measuring gravity waves via the CMB polarization will be challenging. We will undertake a comprehensive study to identify the critical scientific requirements for the mission and their derived instrumental performance requirements. At the core of the study will be an assessment of what is scientifically and experimentally optimal within the scope and purpose of the Einstein Inflation Probe.

Hinshaw, Gary↗

Application of the Shuttle Laser Altimeter in an Accuracy Assessment of Global 1-Kilometer Digital Elevation Data

Shuttle Laser Altimeter (SLA) data have been used to evaluate the accuracy of GTOPO30, the first comprehensive, 1 km resolution, global topographic data set. GTOPO30 was developed by the USGS Eros Data Center (EDC), in part, to address NASA's needs for a global topographic model in support of remote sensing instruments aboard the Earth Observing System AM-1 spacecraft. SLA flew as a part of the STS-72 mission in January, 1996 observing the latitude band from +/- 28.5 deg, and on STS-85 in August, 1997 extending the observations to +/- 57 deg. Combining the SLA ranging data with shuttle position and pointing knowledge yields surface elevation data of very high vertical accuracy in an Earth-centered, absolute reference frame (2.8 m rms difference for SLA-01 with respect to ocean reference surface). Use of the well-determined mean sea surface reference for calibration allows propagation of high accuracy altimetry onto the continents. 436,635 SLA-01 land elevations were compared to the GTOPO30 grid after conversion to a mean sea level vertical datum using the Earth Geoid Model 96, jointly developed by Goddard and NIMA. The comparison reveals systematic elevation biases in southern Asia, Africa, Australia, and south America on the order 10's to 100 meters in the GTOPO30 compilation on spatial scales of 100's to 1000's of kilometers. These biases are likely due to vertical datum errors in the topographic source materials used to compile GTOPO30, which primarily consist of Defense Mapping Agency (DMA) digital elevation and topographic map products. These biases imply that elevation corrections applied to land gravity measurements using these DMA source materials will be biased, leading to errors in geoid models incorporating these land gravity data.

Harding, David J.↗

Thermal Vacuum/Balance Test Results of Swift BAT with Loop Heat Pipe Thermal System

The Swift Burst Alert Telescope (BAT) Detector Array is thermally well coupled to eight constant conductance heat pipes (CCHPs) embedded in the Detector Array Plate PAP), and two loop heat pipes (LHPs) transport heat from the CCHPs to a radiator. The CCHPs have ammonia as the working fluid and the LHPs have propylene as the working fluid. Precision heater controllers, which have adjustable set points in flight, are used to control the LHP compensation chamber and Detector Array xA1 ASIC temperatures. The radiator has AZ-Tek's AZW-LA-II low solar absorptance white paint as the thermal coating, and is located on the anti-sun side of the spacecraft. A thermal balance (T/B) test on the BAT was successfully completed. It validated that the thermal design satisfies the temperature requirements of the BAT in the flight thermal environments. Instrument level and observatory level thermal vacuum (TN) cycling tests of the BAT Detector Array by using the LHP thermal system were successfully completed. This paper presents the results of the T/B test and T N cycling tests.

Choi, Michael K.↗

Flight motor set 360L002 (STS-27R). Volume 5: Nozzle component

A review of the performance and post-flight condition of the STS-27 Redesigned Solid Rocket Motor (RSRM) nozzles is presented. Thermal/Structural instrumentation data is reviewed, and applicable Discrepancy Reports (DRs) and Process Departures (PDs) are presented. The Nozzle Component Program Team (NCPT) performance evaluation and the Redesign Program Review Board (RPRB) assessment is included. The STS-27 nozzle assemblies were flown on the RSRM Second Flight (Space Shuttle Atlantis) on 2 December 1988. The nozzles were a partially submerged convergent and/or divergent movable design with an aft pivot point flexible bearing. The nozzle assemblies incorporated the following features: RSRM forward exit cone with snubber assembly, RSRM fixed housing, Structural backup Outer Boot Ring (OBR), RSRM cowl ring, RSRM nose inlet assembly, RSRM throat assembly, RSRM aft exit cone assembly with Linear-Shaped Charge (LSC), RTV backfill in Joints 1, 3, and 4, Use of EA913 NA adhesive in place of EA913 adhesive, Redesigned nozzle plug, and Carbon Cloth Phenolic (CCP) with 750 ppm sodium content. The CCP material usage for the STS-27 forward nozzle and aft exit cone assemblies is shown.

Meyer, S. A.↗

Vertically Resolved Retrievals of Aerosol Concentrations and Effective Radii from the DOE Combined HSRL and Raman lidar Measurement Study (CHARMS) Merged High-Spectral-Resolution Lidar-Raman Lidar Data Set

The Department of Energy’s (DOE) Atmospheric Radiation Measurement (ARM) Climate Research Facility is a key component of DOE’s research strategy to address global climate change. The objective of the ARM Facility is to provide an experimental testbed for studying important atmospheric effects, particularly cloud and aerosol processes, and testing parameterizations of these processes for use in climate change models. ARM observational sites include a broad array of instruments to characterize cloud and aerosol properties, atmospheric state variables, and incoming and outgoing radiation. Advanced lidar systems provide valuable and unique information about the atmospheric column. We examine the potential for providing vertically resolved information about aerosol size and concentration with a combination of two such lidar systems, the Raman lidar and the High-Spectral-Resolution Lidar (HSRL). Currently ARM has a limited ability to remotely measure profiles of aerosol optical and microphysical properties on an operational basis. Although the Southern Great Plains (SGP), Eastern North Atlantic (ENA), and North Slope of Alaska (NSA, Oliktok Point location only) Raman lidars provide profiles of aerosol backscatter and extinction at 355 nm, additional information is required to better characterize the impacts of aerosols on radiation and clouds. Recent advances in lidar retrieval theory and algorithm development (Müller et al. 1999, 2014; Chemyakin et al. 2014) demonstrate that multi-wavelength lidar retrieval algorithms that use measurements of aerosol extinction at both 355 and 532 nm and backscatter at 355, 532, and 1064 nm have the potential to constrain both the aerosol optical (e.g., complex index of refraction, scattering, etc.) and microphysical properties (e.g., effective radius, concentration). This advancement greatly increases the utility of the remote-sensed aerosol observations. Based on this work, the HSRL group at the National Aeronautics and Space Administration (NASA)’s Langley Research Center (LaRC) developed automated algorithms for retrieving aerosol optical and microphysical properties, demonstrated these retrievals using data from the unique NASA/LaRC airborne multi-wavelength HSRL-2 system, and validated these retrievals using coincident airborne in situ data (Müller et al. 2014; Sawamura et al. 2017). We report here on the use of ARM instrumentation to gather a multi-wavelength ground-based lidar data set to test such retrievals. Continuous (24/7) operation of the co-located SGP Raman lidar and University of Wisconsin (UW) HSRL during the 10-week Combined HSRL and Raman lidar Measurement Study (CHARMS) (mid-July through September 2015) allowed the acquisition of a unique, multi-wavelength ground-based lidar data set. The ARM SGP Raman lidar (RLID) measured profiles of aerosol backscatter, extinction, and depolarization at 355 nm and profiles of water vapor mixing ratio and temperature. The UW HSRL simultaneously measured profiles of aerosol backscatter, extinction and depolarization at 532 nm and aerosol backscatter at 1064 nm. This RLID+HSRL combination provided a test data set to investigate these more advanced aerosol retrieval techniques with the potential to greatly improve aerosol characterization in the lower atmosphere.

54 ENVIRONMENTAL SCIENCES↗

Boron and Lithium in Calcium Sulfate Veins: Tracking Precipitation of Diagenetic Materials in Vera Rubin Ridge, Gale Crater

The NASA Curiosity rover's ChemCam instrument suite has detected boron in calcium-sulfate-filled fractures throughout the sedimentary strata of Gale crater including Vera Rubin ridge. The presence of elevated B concentration provides insights into Martian subsurface aqueous processes. Here, we extend the data set of B in Ca-sulfate veins across Gale crater, comparing the detection frequency and relative abundances with Li. We report 33 new detections of B within veins analyzed between Sols 1548 and 2311 where detections increase in Pettegrove Point and Jura members, which form Vera Rubin ridge. The presence of B and Li in the Ca-sulfate veins is possibly due to dissolution of preexisting B in clays of the bedrock by acids or neutral water and redistribution of the elements into the veins. Elevated frequency of B detection in veins of Gale crater correlates with presence of dehydration features such as desiccation cracks, altered clay minerals and detections of evaporites such as Mg-sulfates and chloride salts in the host rocks. The increased observations of B also coincide with decreased Li concentration in the veins (average Li concentration of veins drops by ~15 ppm). Boron and Li have varying solubilities, and Li does not form salts as readily upon dehydration as B, causing it to remain in the solution. So the weak negative correlation between B and Li may reflect the crystallization sequence during dehydration on Vera Rubin ridge.

58 GEOSCIENCES↗

Surface Water: Stage, Temperature and Discharge, Teller Road Mile Marker 27, Seward Peninsula, Alaska, 2016-2021

Surface water data were collected at one location in the Teller Mile 27 (TL_MM27) Research Basin Site, Seward Peninsula (N64 43' 35.29649", W165 56' 48.42823"). The site was installed and measurements collected from April 2016 to September 2021. During the pandemic, a combination of environmental factors (both animals and climate) led to a gap in the data record from late 2019 to June 2021. Station restarted in June 2021 with the same basin outlet and instrumentation type. These data are being collected to better understand the hydrology of this research basin. The data could also be used as supporting measurements for other research and modeling activities. Stream stage and water temperature are measured every 10 minutes. Discharge in the stream is also measured every site visit using one of two different methods. Most discharge measurements in this data set use the classic US Geological Survey (USGS) style wading rod to measure water velocity at multiple points (every 5 or 10 centimeters) across a known cross-section (https://pubs.usgs.gov/tm/tm3-a8/pdf/tm3-a8.pdf). The second method is the salt-slug mass diffusion method (https://www.uvm.edu/bwrl/lab_docs/protocols/2005_Moore_Slug_salt_dilution_gauging_volumetric_method_Streamline.pdf). Combining the continuous data record with the discrete observations, a stage-discharge relationship was developed. Dataset contains 14 *.csv files including a data dictionary and file-level metadata plus one user guide *.pdf file. DATASET UPDATE: The 2016-2019 data were published in 2019. Data collection continued through 2021 and were added to the dataset in 2025. There were no changes to the 2016-2019 data. Data files now have all years for a measurement combined into one file; whereas before, each measurement and each year had an individual file. The Next-Generation Ecosystem Experiments: Arctic (NGEE Arctic), was a research effort to reduce uncertainty in Earth System Models by developing a predictive understanding of carbon-rich Arctic ecosystems and feedbacks to climate. NGEE Arctic was supported by the Department of Energy's Office of Biological and Environmental Research. The NGEE Arctic project had two field research sites: 1) located within the Arctic polygonal tundra coastal region on the Barrow Environmental Observatory (BEO) and the North Slope near Utqiagvik (Barrow), Alaska and 2) multiple areas on the discontinuous permafrost region of the Seward Peninsula north of Nome, Alaska. Through observations, experiments, and synthesis with existing datasets, NGEE Arctic provided an enhanced knowledge base for multi-scale modeling and contributed to improved process representation at global pan-Arctic scales within the Department of Energy's Earth system Model (the Energy Exascale Earth System Model, or E3SM), and specifically within the E3SM Land Model component (ELM).

54 ENVIRONMENTAL SCIENCES↗

The STEREO Mission: A New Approach to Space Weather Research

With the launch of the twin STEREO spacecraft in July 2006, a new capability will exist for both real-time space weather predictions and for advances in space weather research. Whereas previous spacecraft monitors of the sun such as ACE and SOH0 have been essentially on the sun-Earth line, the STEREO spacecraft will be in 1 AU orbits around the sun on either side of Earth and will be viewing the solar activity from distinctly different vantage points. As seen from the sun, the two spacecraft will separate at a rate of 45 degrees per year, with Earth bisecting the angle. The instrument complement on the two spacecraft will consist of a package of optical instruments capable of imaging the sun in the visible and ultraviolet from essentially the surface to 1 AU and beyond, a radio burst receiver capable of tracking solar eruptive events from an altitude of 2-3 Rs to 1 AU, and a comprehensive set of fields and particles instruments capable of measuring in situ solar events such as interplanetary magnetic clouds. In addition to normal daily recorded data transmissions, each spacecraft is equipped with a real-time beacon that will provide 1 to 5 minute snapshots or averages of the data from the various instruments. This beacon data will be received by NOAA and NASA tracking stations and then relayed to the STEREO Science Center located at Goddard Space Flight Center in Maryland where the data will be processed and made available within a goal of 5 minutes of receipt on the ground. With STEREO's instrumentation and unique view geometry, we believe considerable improvement can be made in space weather prediction capability as well as improved understanding of the three dimensional structure of solar transient events.

Kaiser, michael L.↗

SUBMILLIMETER POLARIZATION OF GALACTIC CLOUDS: A COMPARISON OF 350 {mu}m AND 850 {mu}m DATA

The Hertz and SCUBA polarimeters, working at 350 {mu}m and 850 {mu}m, respectively, have measured the polarized emission in scores of Galactic clouds. Of the clouds in each data set, 17 were mapped by both instruments with good polarization signal-to-noise ratios. We present maps of each of these 17 clouds comparing the dual-wavelength polarization amplitudes and position angles at the same spatial locations. In total number of clouds compared, this is a four-fold increase over previous work. Across the entire data set real position angle differences are seen between wavelengths. While the distribution of {phi}(850)-{phi}(350) is centered near zero (near-equal angles), 64% of data points with high polarization signal-to-noise (P {>=} 3{sigma}{sub p}) have |{phi}(850)-{phi}(350)| > 10 Degree-Sign . Of those data with small changes in position angle ({<=}10 Degree-Sign ) the median ratio of the polarization amplitudes is P(850)/P(350) = 1.7 {+-} 0.6. This value is consistent with previous work performed on smaller samples and models that require mixtures of different grain properties and polarization efficiencies. Along with the polarization data we have also compiled the intensity data at both wavelengths; we find a trend of decreasing polarization with increasing 850-to-350 {mu}m intensity ratio. All the polarization and intensity data presented here (1699 points in total) are available in electronic format.

79 ASTRONOMY AND ASTROPHYSICS↗

ECLSS evolution: Advanced instrumentation interface requirements. Volume 3: Appendix C

An Advanced ECLSS (Environmental Control and Life Support System) Technology Interfaces Database was developed primarily to provide ECLSS analysts with a centralized and portable source of ECLSS technologies interface requirements data. The database contains 20 technologies which were previously identified in the MDSSC ECLSS Technologies database. The primary interfaces of interest in this database are fluid, electrical, data/control interfaces, and resupply requirements. Each record contains fields describing the function and operation of the technology. Fields include: an interface diagram, description applicable design points and operating ranges, and an explaination of data, as required. A complete set of data was entered for six of the twenty components including Solid Amine Water Desorbed (SAWD), Thermoelectric Integrated Membrane Evaporation System (TIMES), Electrochemical Carbon Dioxide Concentrator (EDC), Solid Polymer Electrolysis (SPE), Static Feed Electrolysis (SFE), and BOSCH. Additional data was collected for Reverse Osmosis Water Reclaimation-Potable (ROWRP), Reverse Osmosis Water Reclaimation-Hygiene (ROWRH), Static Feed Solid Polymer Electrolyte (SFSPE), Trace Contaminant Control System (TCCS), and Multifiltration Water Reclamation - Hygiene (MFWRH). A summary of the database contents is presented in this report.

Source record↗

Participation of HNO3 CIMS Instrument in the Sage III Ozone Loss and Validation Experiment (SOLVE)

This project was part of a larger SOLVE project led by Paul Wennberg at California Institute of Technology. The work completed on this project included participating in the installation and preflight testing of a new chemical ionization mass spectrometer for measuring gas and particle phase nitric acid on the ER-2. The investigators subsequently participated in SOLVE where additional instrument improvements were made and a substantial data set was generated. The two Georgia Tech investigators that participated in this work (Fred Eisele and Dave Tanner) had previously been responsible for much of the design and construction of the ion source and mass spectrometer which would be used to measure HNO3 in SOLVE, with Caltech focusing on inlets, calibration, gas supplies/pumping computer control, and overall integration. Thus, a similar focus remained during the SOLVE measurements though all investigators worked on most if not all aspects of the instrument at some point in the mission. Some of the more interesting results from the study included measurements of nitric acid on what are thought to be 5-20 microns diameter individual particles which could supply a local mechanism for HNO3 removal, Nitric acid measurements on SOLVE were completed as a collaborative effort with a great deal of overlap between this project and the larger parent project led by Paul Wennberg. As such, the instrumentation used, its operation, and the resulting measurements are far more fully discussed in the attached report (appendix A) which describes the joint SOLVE nitric acid measurement effort.

Eisele, F. L.↗

Arc-Second Pointer for Balloon-Borne Astronomical Instrument

A control system has been designed to keep a balloon-borne scientific instrument pointed toward a celestial object within an angular error of the order of an arc second. The design is intended to be adaptable to a large range of instrument payloads. The initial payload to which the design nominally applies is considered to be a telescope, modeled as a simple thin-walled cylinder 24 ft (approx.= 7.3 m) long, 3 ft (approx.= 0.91 m) in diameter, weighing 1,500 lb (having a mass of .680 kg). The instrument would be mounted on a set of motor-driven gimbals in pitch-yaw configuration. The motors on the gimbals would apply the control torques needed for fine adjustments of the instrument in pitch and yaw. The pitch-yaw mount would, in turn, be suspended from a motor mount at the lower end of a pair of cables hanging down from the balloon (see figure). The motor in this mount would be used to effect coarse azimuth control of the pitch-yaw mount. A notable innovation incorporated in the design is a provision for keeping the gimbal bearings in constant motion. This innovation would eliminate the deleterious effects of static friction . something that must be done in order to achieve the desired arc-second precision. Another notable innovation is the use of linear accelerometers to provide feedback that would facilitate the early detection and counteraction of disturbance torques before they could integrate into significant angular-velocity and angular-position errors. The control software processing the sensor data would be capable of distinguishing between translational and rotational accelerations. The output of the accelerometers is combined with that of angular position and angular-velocity sensors into a proportional + integral + derivative + acceleration control law for the pitch and yaw torque motors. Preliminary calculations have shown that with appropriate gains, the power demand of the control system would be low enough to be satisfiable by means of storage batteries charged by solar batteries during the day.

Ward, Philip R.↗

Assimilation of Quality Controlled AIRS Temperature Profiles using the NCEP GFS

We have previously conducted a number of data assimilation experiments using AIRS Version-5 quality controlled temperature profiles as a step toward finding an optimum balance of spatial coverage and sounding accuracy with regard to improving forecast skill. The data assimilation and forecast system we used was the Goddard Earth Observing System Model , Version-5 (GEOS-5) Data Assimilation System (DAS), which represents a combination of the NASA GEOS-5 forecast model with the National Centers for Environmental Prediction (NCEP) operational Grid Point Statistical Interpolation (GSI) global analysis scheme. All analyses and forecasts were run at a 0.5deg x 0.625deg spatial resolution. Data assimilation experiments were conducted in four different seasons, each in a different year. Three different sets of data assimilation experiments were run during each time period: Control; AIRS T(p); and AIRS Radiance. In the "Control" analysis, all the data used operationally by NCEP was assimilated, but no AIRS data was assimilated. Radiances from the Aqua AMSU-A instrument were also assimilated operationally by NCEP and are included in the "Control". The AIRS Radiance assimilation adds AIRS observed radiance observations for a select set of channels to the data set being assimilated, as done operationally by NCEP. In the AIRS T(p) assimilation, all information used in the Control was assimilated as well as Quality Controlled AIRS Version-5 temperature profiles, i.e., AIRS T(p) information was substituted for AIRS radiance information. The AIRS Version-5 temperature profiles were presented to the GSI analysis as rawinsonde profiles, assimilated down to a case-by-case appropriate pressure level p(sub best) determined using the Quality Control procedure. Version-5 also determines case-by-case, level-by-level error estimates of the temperature profiles, which were used as the uncertainty of each temperature measurement. These experiments using GEOS-5 have shown that forecasts resulting from analyses using the AIRS T(p) assimilation system were superior to those from the Radiance assimilation system, both with regard to global 7 day forecast skill and also the ability to predict storm tracks and intensity.

Susskind, Joel↗

Photogrammetry-Based Analysis of the On-Orbit Structural Dynamics of the Roll-Out Solar Array

The Roll-Out Solar Array (ROSA) flight experiment was launched to the International Space Station (ISS) on June 3rd, 2017. ROSA is an innovative, lightweight solar array with a flexible substrate that makes use of the stored strain energy in its composite structural members to provide deployment without the use of motors. This paper will discuss the results of various structural dynamics experiments conducted on the ISS during the weeks following launch. Data gathered from instrumentation on the solar array wing during the experiments was previously compared with pre-flight predictions from two different Finite Element Modeling (FEM) efforts. In this paper, data generated from photogrammetry is compared with accelerometer data and used to extend previous conclusions. Whereas previous analyses were only able to track the accelerations of six discrete points on the structure and photovoltaic (PV) blanket of ROSA, the photogrammetry analysis makes available displacements for dozens of points distributed throughout the array. This larger data set makes it possible to compare higher-order PV blanket modes with FEM predictions, in addition to verifying conclusions reached using accelerometer data. The goal in this effort was to better understand the performance of ROSA and to improve modeling efforts for future designs of similar solar arrays.

Chamberlain, Matthew K.↗