Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “INLET FLOW”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

A combined potential and viscous flow solution for V/STOL engine inlets

A potential flow routine and a viscous boundary layer routine have been combined into a single routine for estimating the flow in and around subsonic inlets. In this combined routine, the viscous flow solution about the inlet body is obtained by adding the viscous displacement thickness to the inlet geometry. Combination of the two flow solutions has resulted in cost savings, both in preparation time and in computer time. This routine is a useful tool in optimizing lip shapes for V/STOL inlets. The method of combining the routine, comparison with NASA test data, and utilization of the routine for V/STOL inlet design are presented.

Ybarra, A. H.↗
NASA NTRS2018

Investigation of Turbulence Generated by Upwind Blockages at the Inlet of a 1/50th-Scale Model of the 80- by 120-Foot Wind Tunnel

A 1/50th scale model of the 80- by 120-Foot Wind Tunnel (hereafter referred to as the 80x120) was utilized to determine the magnitude of turbulence caused by buildings located upstream of the wind tunnel inlet. The 1/50th scale models of existing and proposed buildings were constructed to act as blockage for the test. Various inlet locations were sampled for turbulence intensity levels under a variety of blockage conditions including simple three-dimensional rectangular bodies creating quasi two-dimensional physics along the tunnel centerline, existing building structures in the vicinity of the full-scale wind tunnel inlet flow field, and proposed building structures that may someday be constructed at NASA Ames Research Center upwind of the inlet. Therefore, the testing performed and reported in this report can be considered representative of quiescent atmospheric conditions that exist when operating the full-scale 80x120 at night. At quiescent atmospheric conditions there is a measurable increase in turbulence intensity produced by upstream blockages. The blockages examined produced an average turbulence intensity level between 2% and 5% when measured at the inlet. Previous research has shown that the flow control of the 80x120 is capable of reducing this turbulence to less than 0.5% when measured in the test section. Additional research will need to be conducted to determine the influence of atmospheric wind on relative turbulence intensity at the inlet. These results show that for future buildings lying more than 1,000 ft upstream of the full-scale 80x120 inlet, these new buildings will have a negligible effect on the flow quality of the air entering the 80x120 test section under strictly quiescent atmospheric conditions. The Googleplex buildings modeled and tested in this experiment are located approximately 2,450 ft upstream and, as seen in this test campaign, have a negligible influence on the turbulence levels measured at the inlet under quiescent atmospheric conditions.

80- by 120-Foot Wind Tunnel↗
NASA NTRS1981

Flow separation in inlets at incidence angles

Wind-tunnel pressure data and flow pictures obtained for two two-dimensional inlet models have been examined to study the internal flow structure and separation at large incidence angles. The inlet models were 12-in. high (diffuser exit height) and had internal contraction ratio of 1.21 and 1.17. They were tested at low forward speeds over a wide range of throat Mach numbers (inlet mass flow rates) and angles of incidence. Characteristic features of the internal flow such as a drastic change of pressure gradient near the highlight, local separation bubbles and shock/boundary-layer interactions have been indicated and discussed. For a few specific cases, the experimental surface pressure distributions have been compared with theoretical predictions.

Jakubowski, A. K.↗
NASA NTRS1971

Experimental quiet engine program aerodynamic performance of fan A

The aerodynamic component test results are presented of fan A, one of two high-bypass-ratio, 1160 feet per second single-stage fans, which was designed and tested as part of the NASA Experimental Quiet Engine Program. This fan was designed to deliver a bypass pressure ratio of 1.50 with an adiabatic efficiency of 86.5% at a total fan flow of 950 lb/sec. It was tested with and without inlet flow distortion. A bypass total-pressure ratio of 1.52 and an adiabatic efficiency of 88.3% at a total fan flow of 962 lb/sec were actually achieved. An operating margin of 12.4% was demonstrated at design speed.

Giffin, R. G.↗
DOE OSTI2021

Performance evaluation of a Terry GS-2 steam impulse turbine with air-water mixtures

Terry steam turbines are widely used in various industries because of their robust design. Within the nuclear power generation industry, they are used in the Reactor Core Isolation Cooling System to remove decay heat during reactor isolation events. During the Fukushima Daiichi nuclear power station disaster in Japan in 2011, the Reactor Core Isolation Cooling System and associated Terry turbine operated for over 70 hours in Unit 2; this runtime is well beyond the expected operating duration. Theories suggest the turbine was subjected to a two-phase inlet flow, which could degrade the turbine performance. In this work, an experimental test rig was constructed to test a full-scale Terry model GS-2 steam turbine under two-phase air/water flows. Steady-state efficiency and torque performance maps of the turbine were developed over a range of turbine inlet pressures (1.38–4.83 bar or 20–70 psia), air mass fractions (0.05–1.0) and rotational speeds up to 4000 RPM. Furthermore, turbine performance followed expected trends with torque varying linearly and efficiency varying quadratically with rotational speed. In addition, high-speed images of the two-phase flow entering the turbine were also analyzed to understand how changes in inlet pressure and air mass fraction affect the flow regime and homogenization. The present tests with air–water two-phase mixtures are an important step towards providing an understanding of the full-scale Terry turbine’s behavior and performance curves under two-phase conditions. The results of this work will be combined with air/water and steam/water data gathered using a small-scale Terry ZS-1 steam turbine in order to understand the scaling relationship between large and small size Terry turbines and fluid pairs. The combined data set will enable further development of analytical models over a wide range of conditions and may be used to provide technical justification for expanded use of the Terry turbines in nuclear power plant safety systems and other systems.

42 ENGINEERING↗
NASA NTRS1987

A method for assessing effects of circumferential flow distortion on compressor stability

This paper describes the development of a new analysis to predict the onset of flow instability for an axial compressor operating in a circumferentialy distorted inlet flow. A relatively simple model is used to examine the influence of various distortions in setting this instability point. It is found that the model reproduces known experimental trends for the loss of stability margin with increasing distortion amplitude and with changes in reduced frequency. In particular, there is a recognizable 'critical sector angle' which characterizes loss of stability margin. To the authors' knowledge, this is the first time the effects described herein have been theoretically demonstrated as the direct result of a fluid dynamic stability.

Hynes, T. P.↗
NASA NTRS1977

Use of experimental separation limits in the theoretical design of V/STOL inlets

Experimental data from several model inlets are used to generate two parameters which are related to the limit of operation for inlet flow separation. One parameter, called the diffusion ratio, is the ratio of the peak velocity on the inlet surface to the velocity at the diffuser exit and is related to the boundary-layer separation at low throat Mach numbers. The other parameter, the peak Mach number on the inlet surface, is related to the separation at high throat Mach numbers. These parameters are easily calculated from potential flow solutions and thus can be used as a design tool in screening proposed inlet geometries. An illustrative example of an application to an inlet design study for a tilt nacelle VTOL airplane is presented. The value of contraction ratio required to meet the operating requirements yet allow the inlet to remain free of separation as indicated by the two separation parameters is shown.

Boles, M. A.↗
NASA NTRS1977

Use of experimental separation limits in the theoretical design of V/STOL inlets

Experimental data from several model inlets have been used to generate two parameters which are related to the limit of operation for inlet flow separation. One parameter, called the diffusion ratio, is the ratio of the peak velocity on the inlet surface to the velocity at the diffuser exit and is related to the boundary-layer separation at low throat Mach numbers. The other parameter, the peak Mach number on the inlet surface, is related to the separation at high throat Mach numbers. These parameters are easily calculated from potential flow solutions and thus can be used as a design tool in screening proposed inlet geometries. Any of the geometric design variables can be analyzed by this technique; but, this paper is restricted to the consideration of the internal lip contraction ratio. An illustrative example of an application to an inlet design study for a tilt nacelle VTOL airplane is presented. The study will show what value of contraction ratio is required to meet the operating requirements yet allow the inlet to remain free of separation as indicated by the two separation parameters.

Boles, M. A.↗
NASA NTRS2011

Annular MHD Physics for Turbojet Energy Bypass

The use of annular Hall type MHD generator/accelerator ducts for turbojet energy bypass is evaluated assuming weakly ionized flows obtained from pulsed nanosecond discharges. The equations for a 1-D, axisymmetric MHD generator/accelerator are derived and numerically integrated to determine the generator/accelerator performance characteristics. The concept offers a shockless means of interacting with high speed inlet flows and potentially offers variable inlet geometry performance without the complexity of moving parts simply by varying the generator loading parameter. The cycle analysis conducted iteratively with a spike inlet and turbojet flying at M = 7 at 30 km altitude is estimated to have a positive thrust per unit mass flow of 185 N-s/kg. The turbojet allowable combustor temperature is set at an aggressive 2200 deg K. The annular MHD Hall generator/accelerator is L = 3 m in length with a B(sub r) = 5 Tesla magnetic field and a conductivity of sigma = 5 mho/m for the generator and sigma= 1.0 mho/m for the accelerator. The calculated isentropic efficiency for the generator is eta(sub sg) = 84 percent at an enthalpy extraction ratio, eta(sub Ng) = 0.63. The calculated isentropic efficiency for the accelerator is eta(sub sa) = 81 percent at an enthalpy addition ratio, eta(sub Na) = 0.62. An assessment of the ionization fraction necessary to achieve a conductivity of sigma = 1.0 mho/m is n(sub e)/n = 1.90 X 10(exp -6), and for sigma = 5.0 mho/m is n(sub e)/n = 9.52 X 10(exp -6).

Schneider, Steven J.↗
NASA NTRS1979

Effect of steady-state pressure distortion on flow characteristics entering a turbofan engine

Flow angle, static-pressure, and total-pressure distributions were measured in the passage ahead of a turbofan engine operating with inlet pressure distortion. Distortions were generated with five screen configurations and one solid plate configuration. The screens and solid plate were circumferential and mounted on a rotatable assembly. Reynolds Number Index upstream of the distortion device was maintained at 0.5, 0.35, or 0.2, and engine corrected low-rotor speeds were held at 6000 rpm and 8600 rpm. Near the engine inlet, flow angle was largest at the hub and increased as flow approached the engine. The magnitude of static-pressure distortion measured along the inlet-duct and extended bullet nose walls increased exponentially as the flow approached the engine. Wall static-pressure distortion was also a function of distortion harmonic.

Soeder, R. H.↗
NASA NTRS1974

Shock-induced separation of adiabatic turbulent boundary layers in supersonic axially symmetric internal flow

An experimental investigation at Mach 4 of shock-induced turbulent boundary layer separation at the walls of axially symmetric flow passages is discussed, with particular emphasis placed on determining the shock strengths required for incipient separation. The shock waves were produced by interchangeable sting-mounted cones placed on the axes of the flow passages and aligned with the freestream flow. The interactions under study simulate those encountered in axially symmetric engine inlets of supersonic aircraft. Knowledges of the shock strengths required for boundary layer separation in inlets is important since for shocks of somewhat greater strength rather drastic alterations in the inlet flow field may occur.

Page, R. J.↗
NASA NTRS1976

Inlets for high angles of attack

Different inlet designs for high angle of attack STOL and VTOL applications were tested in a subsonic wind tunnel. Three removable entry lips having contraction ratios of 1.30, 1.34 and 1.38 were tested with a single diffuser. The internal contour of each entry lip was an ellipse with a major to minor axis of 2.0. Each lip and diffuser assembly was tested to determine its tolerance to angle of attack, first with a conventional centerbody and then with an extended centerbody. Results indicate that a large improvement in separation angle (determined as a function of lip contraction ratio and inlet flow) was obtained for the extended centerbody for all contraction ratios. Improved inlet tolerance to angle of attack was obtained by reducing the adverse pressure gradient downstream of the throat.

Miller, B. A.↗
NASA NTRS1980

Review - Axial compressor stall phenomena

Stall in compressors can be associated with the initiation of several types of fluid dynamic instabilities. These instabilities and the different phenomena, surge and rotating stall, which result from them, are discussed in this paper. Assessment is made of the various methods of predicting the onset of compressor and/or compression system instability, such as empirical correlations, linearized stability analyses, and numerical unsteady flow calculation procedures. Factors which affect the compressor stall point, in particular inlet flow distortion, are reviewed, and the techniques which are used to predict the loss in stall margin due to these factors are described. The influence of rotor casing treatment (grooves) on increasing compressor flow range is examined. Compressor and compression system behavior subsequent to the onset of stall is surveyed, with particular reference to the problem of engine recovery from a stalled condition. The distinction between surge and rotating stall is emphasized because of the very different consequences on recoverability. The structure of the compressor flow field during rotating stall is examined, and the prediction of compressor performance in rotating stall, including stall/unstall hysteresis, is described.

Greitzer, E. M.↗
NASA NTRS2001

A Performance Map for Ideal Air Breathing Pulse Detonation Engines

The performance of an ideal, air breathing Pulse Detonation Engine is described in a manner that is useful for application studies (e.g., as a stand-alone, propulsion system, in combined cycles, or in hybrid turbomachinery cycles). It is shown that the Pulse Detonation Engine may be characterized by an averaged total pressure ratio, which is a unique function of the inlet temperature, the fraction of the inlet flow containing a reacting mixture, and the stoichiometry of the mixture. The inlet temperature and stoichiometry (equivalence ratio) may in turn be combined to form a nondimensional heat addition parameter. For each value of this parameter, the average total enthalpy ratio and total pressure ratio across the device are functions of only the reactant fill fraction. Performance over the entire operating envelope can thus be presented on a single plot of total pressure ratio versus total enthalpy ratio for families of the heat addition parameter. Total pressure ratios are derived from thrust calculations obtained from an experimentally validated, reactive Euler code capable of computing complete Pulse Detonation Engine limit cycles. Results are presented which demonstrate the utility of the described method for assessing performance of the Pulse Detonation Engine in several potential applications. Limitations and assumptions of the analysis are discussed. Details of the particular detonative cycle used for the computations are described.

Paxson, Daniel E.↗
NASA NTRS2009

Design and Analysis Tools for Supersonic Inlets

Computational tools are being developed for the design and analysis of supersonic inlets. The objective is to update existing tools and provide design and low-order aerodynamic analysis capability for advanced inlet concepts. The Inlet Tools effort includes aspects of creating an electronic database of inlet design information, a document describing inlet design and analysis methods, a geometry model for describing the shape of inlets, and computer tools that implement the geometry model and methods. The geometry model has a set of basic inlet shapes that include pitot, two-dimensional, axisymmetric, and stream-traced inlet shapes. The inlet model divides the inlet flow field into parts that facilitate the design and analysis methods. The inlet geometry model constructs the inlet surfaces through the generation and transformation of planar entities based on key inlet design factors. Future efforts will focus on developing the inlet geometry model, the inlet design and analysis methods, a Fortran 95 code to implement the model and methods. Other computational platforms, such as Java, will also be explored.

Slater, John W.↗
NASA NTRS1985

Forced response analysis of an aerodynamically detuned supersonic turbomachine rotor

High performance aircraft-engine fan and compressor blades are vulnerable to aerodynamically forced vibrations generated by inlet flow distortions due to wakes from upstream blade and vane rows, atmospheric gusts, and maldistributions in inlet ducts. In this report, an analysis is developed to predict the flow-induced forced response of an aerodynamically detuned rotor operating in a supersonic flow with a subsonic axial component. The aerodynamic detuning is achieved by alternating the circumferential spacing of adjacent rotor blades. The total unsteady aerodynamic loading acting on the blading, as a result of the convection of the transverse gust past the airfoil cascade and the resulting motion of the cascade, is developed in terms of influence coefficients. This analysis is used to investigate the effect of aerodynamic detuning on the forced response of a 12-blade rotor, with Verdon's Cascade B flow geometry as a uniformly spaced baseline configuration. The results of this study indicate that, for forward traveling wave gust excitations, aerodynamic detuning is very beneficial, resulting in significantly decreased maximum-amplitude blade responses for many interblade phase angles.

Hoyniak, D.↗
NASA NTRS1973

Design and experimental results for a turbine with jet flap stator and jet flap

The overall performance and detailed stator performance of a negative hub reaction turbine design featuring a moderately low solidity jet flap stator and a jet flap rotor were determined. Testing was conducted over a range of turbine expansion ratios at design speed. At each expansion ratio, the stator jet flow and rotor jet flow ranged up to about 7 and 8 percent, respectively, of the turbine inlet flow. The performance of the jet flap stator/jet flap rotor turbine was compared with that of a turbine which used the same jet flap rotor and a conventional, high solidity plan stator. The effect on performance of increased axial spacing between the jet stator and rotor was also investigated.

Bettner, J. L.↗
NASA NTRS1973

Analytical method for predicting the pressure distribution about a nacelle at transonic speeds

The formulation and development of a computer analysis for the calculation of streamlines and pressure distributions around two-dimensional (planar and axisymmetric) isolated nacelles at transonic speeds are described. The computerized flow field analysis is designed to predict the transonic flow around long and short high-bypass-ratio fan duct nacelles with inlet flows and with exhaust flows having appropriate aerothermodynamic properties. The flow field boundaries are located as far upstream and downstream as necessary to obtain minimum disturbances at the boundary. The far-field lateral flow field boundary is analytically defined to exactly represent free-flight conditions or solid wind tunnel wall effects. The inviscid solution technique is based on a Streamtube Curvature Analysis. The computer program utilizes an automatic grid refinement procedure and solves the flow field equations with a matrix relaxation technique. The boundary layer displacement effects and the onset of turbulent separation are included, based on the compressible turbulent boundary layer solution method of Stratford and Beavers and on the turbulent separation prediction method of Stratford.

Keith, J. S.↗