Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fracturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

CO 2 -Responsive Fracturing Fluids for Enhanced Geothermal Systems (Final Report)

Our group has recently developed StimuFrac, a non-toxic stimuli-responsive fracturing fluid consisting of a CO 2 -reactive polymer which has shown at the lab-scale to consistently fracture rock cores at significantly lower net pressures in a range of representative geothermal pressure/temperature conditions. However, until now the mechanism/s responsible for more effective fracturing, of critical importance to optimize fracturing performance as well as strategize injection methodologies for field deployment, was not understood. In this document, we report (1) on the two main mechanisms responsible for fracturing rock at lower net pressures with StimuFrac; (2) the phase behavior of StimuFrac/CO 2 under geothermal wellbore conditions; and (3) based on high-temperature true triaxial stimulations, detailed evidence that StimuFrac/CO 2 is the best performing stimulation fluid under EGS T/P conditions as compared to water, waterless CO 2 , and CO 2 /water fracturing fluids. This is because i) it requires significantly lower volumes of CO 2 due to its reduced leak off into the formation by the crosslinked polymer solution; ii) large fractures can be generated reproducibly at both low and high CO 2 injection flow rates, and iii) the reversible (previously reported) viscosity increase of StimuFrac could be beneficial to transport proppants when they become available for EGS. These results were particularly evident for hot nearly dry rock as well as partially and nearly fully water-saturated granitic rock. GTO requires StimuFrac to be evaluated in fully water-saturated rock to determine whether the above-described performance applies under these conditions. Since (1) GTO considers there is no enough evidence for Sa different StimuFrac formulation to work below 90C (where full water-saturation in an open system is possible) and (2) no polyaxial loading frame larger than a few centimeters that can do hydraulic fracturing tests while maintaining the rock sample fully saturated with water at 200 C exists; PNNL concludes that the only way to determine if StimuFrac represents an advanced fracturing fluid alternative for EGS, is to perform a stimulation in an actual EGS reservoir.

15 GEOTHERMAL ENERGY↗
NASA NTRS1976

A fractographic study of the edge-sliding mode in fracture toughness testing

A fractographic study of Mode II fracture surfaces has been conducted for the purpose of identifying the microstructural mechanisms responsible for fracture in the edge-sliding mode. A compact shear (CS) specimen was employed to generate the fracture surfaces and also to establish Mode II fracture toughness values for Ti-6Al-4V, A533-B steel, and several aluminum alloys. In all tests, one of the two edge cracks sustained complete Mode II fracture while the other exhibited only a limited amount of subcritical crack growth. Mode II fracture surfaces, which were unique in appearance, have been examined by optical and scanning electron microscopy. It was determined that shear (or parabolic) microvoid coalescence was the dominant mechanism for Mode II fracture. It was also established that most of the surface abrasions were created by the relative sliding of the fracture surfaces during unstable fracture rather than the crack initiation process.

Jones, D. L.↗
NASA NTRS1976

Ductile fracture theories for pressurised pipes and containers

Two mechanisms of fracture are distinguished. Plane strain fractures occur in materials which do not undergo large-scale plastic deformations prior to and during a possible fracture deformation. Plane stress or high energy fractures are generally accompanied by large inelastic deformations. Theories for analyzing plane stress are based on the concepts of critical crack opening stretch, K(R) characterization, J-integral, and plastic instability. This last is considered in some detail. The ductile fracture process involves fracture initiation followed by a stable crack growth and the onset of unstable fracture propagation. The ductile fracture propagation process may be characterized by either a multiparameter (discrete) model, or some type of a resistance curve which may be considered as a continuous model expressed graphically. These models are studied and an alternative model is also proposed for ductile fractures which cannot be modeled as progressive crack growth phenomena.

Erdogan, F.↗
NASA NTRS1977

Mechanical behavior and fracture characteristics of off-axis fiber composites. 1: Experimental investigation

The mechanical behavior, fracture surfaces, and fracture modes of unidirectional high-modulus graphite-fiber/epoxy composites subjected to off-axis tensile loads were investigated experimentally. The investigation included the generation of stress-strain-to-fracture data and scanning electron microscope studies of the fractured surfaces. The results led to the identification of fracture modes and distinct fracture surface characteristics for off-axis tensile loading. The results also led to the formulation of critical for identifying and characterizing these fracture modes and their associated fracture surfaces. The results presented and discussed herein were used in the theoretical investigation and comparisons described in Part 2. These results should also provide a good foundation for identifying, characterizing, and quantifying fracture modes in both off-axis and angle-plied laminates.

Sinclair, J. H.↗
NASA NTRS1978

Metallurgical characterization of the fracture of aluminum alloys

A systematic investigation was conducted to examine the fracture behavior of the structural aluminum alloys 2024, 6061, 7075, and 7178 (in selected heat treatments) tested under several controlled conditions. The investigation included both time independent (tensile, shear, and precracked notch-bend) fractures and time dependent (fatigue and stress corrosion) fractures. Specimens were obtained from both sheet and plate material and tested in longitudinal and transverse orientations. Strain rate effects on fracture morphology were examined in tension and shear tests. Fatigue fracture studies included an examination of the influence of minimum-to-maximum-load ratio on fracture morphology. Second-phase particles observed on fracture surfaces and metallographically prepared sections and corrosion products associated with stress corrosion fractures were analyzed chemically using scanning electron microscopy and energy-dispersive X-ray analysis. Fracture morphology was related to the microstructural features, the testing conditions, and the form of commercial product.

Bhandarkar, M. D.↗
NASA NTRS1983

Fracture behavior of the Space Shuttle thermal protection system

Stable crack-growth and fracture-toughness experiments were conducted using precracked specimens machined from LI-900 reusable surface insulation (RSI) tiles of the Space Shuttle thermal protection system (TPS) at room temperature. Similar fracture experiments were conducted on fracture specimens with preexisting cracks at the interface of the tile and the strain isolation pad (SIP). Stable crack growth was not observed in the LI-900 tile fracture specimens which had a fracture toughness of 12.0 kPa sq rt of m. The intermittent subcritical crack growth at the tile-pad interface of the fracture specimens was attributed to successive local pull-outs due to tensile overload in the LI-900 tile and cannot be characterized by linear elastic fracture mechanics. No subcritical interfacial crack growth was observed in the fracture specimens with densified LI-900 tiles where brittle fracture initiated at an interior point away from the densification.

Komine, A.↗
NASA NTRS1990

Computational simulation of structural fracture in fiber composites

A methodology was developed for the computational simulation of structural fracture in fiber composites. This methodology consists of step-by-step procedures for mixed-mode fracture in generic components and an integrated computer code, Composite Durability Structural Analysis (CODSTRAN). The generic types of composite structural fracture include: (1) single and combined mode fracture in beams; 2) laminate free-edge delamination fracture; and (3) laminate center flaw progressive fracture. Structural fracture is identified by rapid changes in one or all of the following: (1) displacements, (2) frequencies, (3) the buckling loads, or (4) the strain energy release rate. These rapid changes are herein assumed to denote imminent structural fracture. Based on these rapid changes, parameters are identified which can be used as guidelines for structural fracture, inspection intervals and retirement for cause.

Chamis, Christos C.↗
NASA NTRS1990

Computational simulation of structural fracture in fiber composites

A methodology was developed for the computational simulation of structural fracture in fiber composites. This methodology consists of step-by-step procedures for mixed mode fracture in generic components and of an integrated computer code, Composite Durability Structural Analysis (CODSTRAN). The generic types of composite structural fracture include single and combined mode fracture in beams, laminate free-edge delamination fracture, and laminate center flaw progressive fracture. Structural fracture is assessed in one or all of the following: (1) the displacements increase very rapidly; (2) the frequencies decrease very rapidly; (3) the buckling loads decrease very rapidly; or (4) the strain energy release rate increases very rapidly. These rapid changes are herein assumed to denote imminent structural fracture. Based on these rapid changes, parameters/guidelines are identified which can be used as criteria for structural fracture, inspection intervals, and retirement for cause.

Chamis, C. C.↗
NASA NTRS1993

Combined mode I and mode II fracture of monolithic ceramics

The mode I, mode II, and combined mode I-mode II fracture behaviors of a coarse-grained silicon nitride, a fine-grained silicon nitride, and an alumina were investigated. These ceramics were fractured from two types of fracture initiating flaws: small surface flaws and large single edge precracks. The small surface flaws were introduced by Knoop indentation in flexural samples at various angles to the tensile stress direction and fractured in four-point bending. The samples with large precracks were fractured in the asymmetric four-point-bend geometry. The mixed-mode fracture toughness values obtained from the two flaw configurations were in good agreement with each other. All three ceramics displayed very similar mixed-mode fracture behavior, although their microstructures were not similar. Comparison of experimental data to mixed-mode fracture theories revealed that the minimum strain energy density theory best described the mixed-mode fracture behavior of all three ceramics.

Tikare, Veena↗
NASA NTRS1994

The Relationship Between Constraint and Ductile Fracture Initiation as Defined by Micromechanical Analyses

The use of small laboratory specimens to predict the integrity of large, complex structures relies on the validity of single parameter fracture mechanics. Unfortunately, the constraint loss associated with large scale yielding, whether in a laboratory specimen because of its small size or in a structure because it contains shallow flaws loaded in tension, can cause the breakdown of classical fracture mechanics and the loss of transferability of critical, global fracture parameters. Although the issue of constraint loss can be eliminated by testing actual structural configurations, such an approach can be prohibitively costly. Hence, a methodology that can correct global fracture parameters for constraint effects is desirable. This research uses micromechanical analyses to define the relationship between global, ductile fracture initiation parameters and constraint in two specimen geometries (SECT and SECB with varying a/w ratios) and one structural geometry (circumferentially cracked pipe). Two local fracture criteria corresponding to ductile fracture micromechanisms are evaluated: a constraint-modified, critical strain criterion for void coalescence proposed by Hancock and Cowling and a critical void ratio criterion for void growth based on the Rice and Tracey model. Crack initiation is assumed to occur when the critical value in each case is reached over some critical length. The primary material of interest is A516-70, a high-hardening pressure vessel steel sensitive to constraint; however, a low-hardening structural steel that is less sensitive to constraint is also being studied. Critical values of local fracture parameters are obtained by numerical analysis and experimental testing of circumferentially notched tensile specimens of varying constraint (e.g., notch radius). These parameters are then used in conjunction with large strain, large deformation, two- and three-dimensional finite element analyses of the geometries listed above to predict crack initiation loads and to calculate the associated (critical) global fracture parameters. The loads are verified experimentally, and microscopy is used to measure pre-crack length, crack tip opening displacement (CTOD), and the amount of stable crack growth. Results for A516-70 steel indicate that the constraint-modified, critical strain criterion with a critical length approximately equal to the grain size (0.0025 inch) provides accurate predictions of crack initiation. The critical void growth criterion is shown to considerably underpredict crack initiation loads with the same critical length. The relationship between the critical value of the J-integral for ductile crack initiation and crack depth for SECT and SECB specimens has been determined using the constraint-modified, critical strain criterion, demonstrating that this micromechanical model can be used to correct in-plane constraint effects due to crack depth and bending vs. tension loading. Finally, the relationship developed for the SECT specimens is used to predict the behavior of circumferentially cracked pipe specimens.

Panontin, Tina L.↗
DOE OSTI2019

Research Considerations for Foam Fracturing in Stimulation Development for Enhanced Geothermal Systems

In regions where hydraulic fracturing is being considered for enhanced geothermal systems (EGS), and use of water is an issue, foam fracturing is an attractive option as a reduced water or waterless stimulation method. Although it has been shown to be an effective alternative in oil & gas production, foam fracturing has not yet been demonstrated in geothermal energy development. There are many challenges encountered in EGS. The reservoir may be located at great depth where earth stresses will be large and rock strength may be high. In addition, the viscosity of foam is higher than that of a pure single-phase fluid. Thus, the fracturing pressure will be increased substantially if a conventional fracturing routine is used. Moreover, fracturing in EGS systems may have more potential for induced seismicity. A proactive approach is proposed to address this technical challenge by using pulsed injection in a current project, sponsored by the U.S. DOE GTO Waterless Stimulation Initiative. This approach enables the dynamic responses of rock structure to be utilized and a new cavitation-based material-removal mechanism to be explored for enhanced fracturing efficiency. It also offers an approach to mitigate fracturing-induced seismicity and the potential to control dynamic behavior of foamed fluids. Research considerations will be described for investigation of the above phenomena in foam fracturing for EGS stimulation development.

Wang, Hong↗
DOE OSTI2019

Fracture Tracer Injection Response to Pressure Perturbations at an Injection Well

The EGS Collab project constructed an approximately ten-meter scale field site where fracture stimulation and flow/transport models can be validated against controlled, in-situ experiments. The first multi-well experimental site was established at the 4850 level of the Stanford Underground Research Facility (SURF) in the Homestake Mine located in South Dakota. Hydraulic fractures were created at an injection well drilled sub-horizontal from the drift. A flow system was established in one set of fractures by injection water at approximately 400 ml/min between a set of packers 164 feet from the drift wall in the injection well through a hydraulically stimulated fracture. Injected water was recovered from five locations in 4 nearby wells. From the end of October to the middle of November of 2018, a series of fracture characterization tests were conducted using a series of 10 tracer tests (7 which used C-dot and chloride as conservative solute tracers) to assess the flow pathway in the stimulated fracture. The injected tracers were detected in three of the five water production locations where the total water recovery ranged from approximately 50 to 80% of the injected water depending on the day the test was being conducted. Analysis of a series of tracers during this two-week period suggest a large change in the flow fracture field occurred during this testing period. A comparison of the tracer breakthrough curves at the production well showed a marked decrease in the initial and peak concentration over time, whereas the OB well exhibited an increase in the initial and peak concentration arrival during this fracture characterization testing period. These changes are believed to be in response to a number of higher-pressure short-term injections at the injection well in early November (2nd to the 6th). Results of this testing suggest that the fracture flow pathways can be altered as a result of the pressure perturbations in the injection well on the integrity of adjacent monitoring wells. Results from the EGS Collab project will support the DOE Geothermal Technology Office FORGE and other EGS development efforts.

15 GEOTHERMAL ENERGY↗
DOE OSTI2019

Multi-stage geologic fracturing

Explosive geologic fracturing methods, devices, and systems can be used in combination with other geologic fracturing means, such as hydraulic fracturing methods, devices and systems, or other fluid-based fracturing means. An exemplary method comprises introducing an explosive system into a wellbore in a geologic formation, detonating the explosive system in the wellbore to fracture at least a first portion of the geologic formation adjacent to the wellbore, and introducing pressurized fluid into the wellbore to enhance the fracturing of the first portion of the geologic formation. Such multi-stage fracturing can further enhance the resulting fracturing of geologic formation relative to explosive fracturing alone.

Mace, Jonathan Lee↗
DOE OSTI2020

Fracture toughness of zirconia with a nanometer size notch fabricated using focused ion beam milling

Zirconia with 3 mol% yttria (3Y-TZP) has been used for dental crowns and bridges due to its excellent mechanical behavior. Performing fracture toughness testing on this nanograin material, however, can be a challenge. For reliable results, fracture toughness testing requires an extremely sharp notch in the test specimen that closely approximates a very sharp crack. This study was to investigate an alternative method to produce nanometer-sized notches, which are less than the average grain size of 3Y-TZP, during the preparation of single-edge V-notched beam specimens and report the resulting fracture toughness value. We present a method using focused ion beam (FIB) milling to fabricate nanometer-sized notches in 3Y-TZP. The notch tip is <100 nm wide, which is smaller than the grain size, and is consistent throughout the thickness of the specimen. The FIB-notched specimens show a much reduced average fracture toughness of 5.64 ± 1.14 MPa√m compared to 8.90 ± 0.23 MPa√m for the specimens without FIB-notches. The FIB-milling did not appear to create any monoclinic phase prior to fracture toughness testing. Fractures originated at the FIB-notches, and the notch size can be readily identified post-mortem using a microscope. A considerable amount of tetragonal-to-monoclinic phase transformation was observed throughout the fracture surfaces. FIB milling provides an alternative method to fabricate nanometer-sized notches that are smaller than the grain size of tetragonal zirconia polycrystal. The fracture toughness determined using FIB-notches was ~5.64 MPa√m, smaller than the specimens with V-notches fabricated using saw blades.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Influence of build direction on the fracture mechanism of 3D printed octet lattices

Here, we investigate the effects of 3D printing build directions on the fracture properties of octet lattice metamaterials made of polylactic acid (PLA) and how these effects vary with the relative density of the lattices. Single-edge notch bend samples are 3D printed in two orthogonal build directions at various relative densities. Our results show that the work of fracture for octet lattices with build directions parallel to the crack plane is significantly higher than those with build directions perpendicular to the crack plane. We also observed that the ratio of specific work of fracture between the two build directions remains nearly constant across different relative densities. In contrast, the ratio of peak load between the two build directions decreases as relative density increases. Furthermore, the build direction dictates the fracture mechanism. While the perpendicular build direction predominantly results in a brittle (mode I) fracture, the parallel build direction leads to a complex, delamination-dominated (mode II type) fracture. This phenomenon is largely governed by the weak interfaces formed between the printed layers and their interaction with the lattice geometry. These results reveal that the build direction governs the fracture mechanism and work of fracture of these lattice metamaterials and is therefore an important design consideration.

3D printed PLA↗
DOE OSTI2026

In situ quantification of fracture slip induced by hydraulic injections in a deep borehole: A comparison of two different borehole techniques

In situ measurements of fracture deformation during fluid injection are rare, yet essential for understanding the mechanical response of fractured rock. In this study, we evaluate the reliability of two methods by comparing their slip vector estimates: high-resolution borehole acoustic televiewer images captured before and after injection tests, and displacement data from a three-component borehole deformation probe recorded during the injections. Acoustic televiewer images capture only final in-plane displacement, whereas three-component borehole deformation measurements provide full 3D, transient fracture movement. Four injection tests in a fractured granitic rock mass along an inclined borehole at the Bedretto Underground Laboratory (Switzerland), beneath more than 1100 m of overburden, were analyzed. The two methods yielded consistent kinematics and comparable slip magnitudes, typically in the range of 0.2 – 0.6 mm. Angular differences between estimated slip directions ranged from 0.2° to 28°. For two test intervals with pre-existing fractures optimally oriented for slip, the measured slip vectors agreed with forward-modeled slip vectors based on the regional in situ stress field, supporting the Wallace–Bott hypothesis. Measurable shear displacement was identified in two test intervals containing fractures oriented nearly perpendicular to the least principal stress, including a newly formed hydraulic fracture. This demonstrates that even fractures unfavorably oriented for slip can undergo shear due to local stress perturbations around an inclined borehole.

Acoustic televiewer↗
DOE OSTI2018

Fracture resistance of high entropy alloys: A review

Fascinated by the exceptional mechanical properties of high entropy alloys (HEAs), unremitting endeavors are placed on accelerating their engineering applications in multiple critical fields. As all other structural materials, attaining sufficient fracture resistance is a vital requirement for HEAs, particularly for safety critical applications. Along this line, the fracture resistance of a number of HEAs and medium-entropy alloys (MEAs) had been studied in the past decade. While some exhibit unprecedented fracture toughness akin to the toughest materials ever known, others are just alike brittle materials. Herein, we summarize one decade of investigations of the fracture resistance of HEAs and MEAs, including the characterization of fracture toughness, disclosure of fractographic characteristics, and understanding of fracture micro-mechanisms. The role of alloy composition, temperature, phase constituent, and characterization techniques in altering the fracture toughness are discussed; characteristics of the cleavage and shear fractures are detailed; toughening and weakening mechanisms, from the atomic to the defect level, are reviewed. In conclusion, some key questions are raised, and the directions for future research are suggested.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Permeability Evolution of Fractures in Shale in the Presence of Supercritical CO 2

We experimentally examined the impact of supercritical carbon dioxide (scCO 2 ) on fracture permeability and fracture surface characteristics in shales of various compositions. We measured permeability and fracture normal displacement at different effective stresses using both argon and scCO 2 as pore fluids. Both natural fractures and saw cuts in intact samples were used in our study. The permeability and fracture normal displacement decrease after multiple loading/unloading cycles, apparently as the result of inelastic compaction. In samples with high carbonate content, we observe an increase in permeability and fracture surface degradation after more than 3.5 days of exposure to scCO 2 , apparently due to carbonate dissolution. We demonstrate that the sensitivity of permeability to effective normal stress correlates well with the fracture normal displacement. The dependence of permeability on effective normal stress increases after exposure to scCO 2 as the fracture surface became more compliant.

58 GEOSCIENCES↗