Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Dynamic Analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Free-interface methods of substructure coupling for dynamic analysis

Benfield, et al. (1972) showed that among fixed-interface, free-interface, and hybrid substructure coupling methods, the fixed-interface methods as the most accurate and the free-interface methods are the least accurate. In the present note, a substructure coupling method is proposed which employs free-interface substructure modes supplemented by 'reduced flexibility.' Substructure coupling based on the improved substructure model is discussed, and a numerical comparison with Hou's free-interface method is given. To simplify representation of the method proposed, the substructure equations are developed first for constrained substructures, and then the equations representing substructures with rigid-body modes are given. Finally, the equations for coupling of substructures are derived. Example calculations are included.

Craig, R. R., Jr.↗

Dynamic analysis of a photovoltaic power system with battery storage capability

A photovolataic power system with a battery storage capability is analyzed. A dual battery current control concept is proposed, which enables the battery to either supply or accept power depending upon system environment and load conditions. A simulation of the power system, including the battery current control, is developed and evaluated. The evaulation demonstrate the visbility of the battery control concept of switch the battery from a charge to discharge mode and back as required by load and environmental conditions. An acceptable system operation is demonstrated over the entire insolation range. Additionally, system sensitivity, bandwidth, and damping characteristics of the battery control are shown to be acceptable for a projected hardware implementation.

Merrill, W. C.↗

Transient dynamic analysis of high-speed lightly loaded cylindrical roller bearings. 1: Analysis

The governing differential equations of motion for a high speed cylindrical roller bearing are developed under the assumptions that the bearing is isothermal and that the roller tilt and skew are very small. Two sets of differential equations are presented: the first which deals with planar motion of the roller bearing system; and the second which includes the effect of roller skewing. The equations as presented are in a format for programming on a digital computer.

Conry, T. F.↗

Transient dynamic analysis of high-speed lightly loaded cylindrical roller bearings. 2: Computer program and results

The governing differential equations of motion for a high speed cylindrical roller bearing are programmed for numerical solution and plotted output. This computer program has the capability of performing a two dimensional or three dimensional simulation. Two numerical solutions of the governing differential equations were obtained to simulate the motion of a roller bearing, one for the two dimensional equations of motion and one for the three dimensional equations of motion. Computer generated plots were obtained and present such data as roller/cage interaction forces, roller/race traction forces, roller/race relative slip velocities and cage angular speed over a nondimensional time equivalent to 1.2 revolutions of the inner race. Roller axial displacement, roller skew angle, and skew moment are also plotted for the three dimensional solution. The trajectory of the cage center is plotted for both the two dimensional and three dimensional solutions.

Conry, T. F.↗

Computer program documentation for the dynamic analysis of a noncontacting mechanical face seal

A computer program is presented which achieves a numerical solution for the equations of motion of a noncontacting mechanical face seal. The flexibly-mounted primary seal ring motion is expressed by a set of second order differential equations for three degrees of freedom. These equations are reduced to a set of first order equations and the GEAR software package is used to solve the set of first order equations. Program input includes seal design parameters and seal operating conditions. Output from the program includes velocities and displacements of the seal ring about the axis of an inertial reference system. One example problem is described.

Auer, B. M.↗

Blade loss transient dynamics analysis, volume 1. Task 1: Survey and perspective

An analytical technique was developed to predict the behavior of a rotor system subjected to sudden unbalance. The technique is implemented in the Turbine Engine Transient Rotor Analysis (TETRA) computer program using the component element method. The analysis was particularly aimed toward blade-loss phenomena in gas turbine engines. A dual-rotor, casing, and pylon structure can be modeled by the computer program. Blade tip rubs, Coriolis forces, and mechanical clearances are included. The analytical system was verified by modeling and simulating actual test conditions for a rig test as well as a full-engine, blade-release demonstration.

Gallardo, V. C.↗

Blade loss transient dynamics analysis. Volume 3: User's manual for TETRA program

The users manual for TETRA contains program logic, flow charts, error messages, input sheets, modeling instructions, option descriptions, input variable descriptions, and demonstration problems. The process of obtaining a NASTRAN 17.5 generated modal input file for TETRA is also described with a worked sample.

Black, G. R.↗

Dynamic analysis of a free-tip rotor

The flag-lag-torsion flutter of a constant-lift rotor (CLR) and a free-tip rotor (FTR) has been investigated in hovering flight. The CLR blade consists of a finite number of strips pivotally mounted on the spar; torsional stiffness of the strips is attained through the elastic axis offset from the aerodynamic center. It is shown that, with a suitable combination of lag damper and negative pitch-flap coupling, it is possible to design a CLR blade that is free of aeroelastic instability with suitable airfoil selection. The FTR blade, which consists of an inboard section similar to that of a conventional blade and a small outboard section freely pitching on its spar, is also free of aeroelastic instability.

Chopra, I.↗

Rotating unconstrained modes - A more appropriate dynamic analysis of flexible spinning spacecraft

The objective of the paper is a formation of vehicle modes for gyroscopic space structures through a continuum formulation. This requires examination of adjointness of the associated eigenvalue problems. It is shown that standard conditions of self-adjointness are inadequate even for nongyroscopic structures; modifications required depend on the problem under study. On one hand, in the nongyroscopic case the frequencies appear only quadratically and it is relatively easy to devise the corresponding vehicle modes and the self-adjoint operators. On the other hand in the case of the gyroscopic structures the frequencies appear quadratically as well as linearly; this takes the vehicle mode from a configuration space to a phase space, that is, a Hilbert space in the present case. Four elastic systems of increasing complexity typifying nonspinning and spinning elastic spacecraft are investigated in detail.

Hablani, H. B.↗

Formulation of a dynamic analysis method for a generic family of hoop-mast antenna systems

Analytical studies of mast-cable-hoop-membrane type antennas were conducted using a transfer matrix numerical analysis approach. This method, by virtue of its specialization and the inherently easy compartmentalization of the formulation and numerical procedures, can be significantly more efficient in computer time required and in the time needed to review and interpret the results.

Gabriele, A.↗

Track train dynamics analysis and test program: Methodology development for the derailment safety analysis of six-axle locomotives

The operational safety of six axle locomotives is analyzed. A locomotive model with corresponding data on suspension characteristics, a method of track defect characterization, and a method of characterizing operational safety are used. A user oriented software package was developed as part of the methodology and was used to study the effect (on operational safety) of various locomotive parameters and operational conditions such as speed, tractive effort, and track curvature. The operational safety of three different locomotive designs was investigated.

Marcotte, P. P.↗

Application of a systematic finite-element model modification technique to dynamic analysis of structures

A systematic finite-element model modification technique has been applied to two small problems and a model of the main wing box of a research drone aircraft. The procedure determines the sensitivity of the eigenvalues and eigenvector components to specific structural changes, calculates the required changes and modifies the finite-element model. Good results were obtained where large stiffness modifications were required to satisfy large eigenvalue changes. Sensitivity matrix conditioning problems required the development of techniques to insure existence of a solution and accelerate its convergence. A method is proposed to assist the analyst in selecting stiffness parameters for modification.

Robinson, J. C.↗

Blade loss transient dynamic analysis of turbomachinery

This paper reports on work completed to develop an analytical method for predicting the transient non-linear response of a complete aircraft engine system due to the loss of a fan blade, and to validate the analysis by comparing the results against actual blade loss test data. The solution, which is based on the component element method, accounts for rotor-to-casing rubs, high damping and rapid deceleration rates associated with the blade loss event. A comparison of test results and predicted response show good agreement except for an initial overshoot spike not observed in test. The method is effective for analysis of large systems.

Stallone, M. J.↗

Engine dynamic analysis with general nonlinear finite element codes. II - Bearing element implementation, overall numerical characteristics and benchmarking

Second-year efforts within a three-year study to develop and extend finite element (FE) methodology to efficiently handle the transient/steady state response of rotor-bearing-stator structure associated with gas turbine engines are outlined. The two main areas aim at (1) implanting the squeeze film damper element into a general purpose FE code for testing and evaluation; and (2) determining the numerical characteristics of the FE-generated rotor-bearing-stator simulation scheme. The governing FE field equations are set out and the solution methodology is presented. The choice of ADINA as the general-purpose FE code is explained, and the numerical operational characteristics of the direct integration approach of FE-generated rotor-bearing-stator simulations is determined, including benchmarking, comparison of explicit vs. implicit methodologies of direct integration, and demonstration problems.

Padovan, J.↗

Efficient computerized model for dynamic analysis of energy conversion systems

In searching for the optimum parameters that minimize the total life cycle cost of an energy conversion system, various combinations of components are examined and the resulting system performance and associated economics are studied. The systems performance and economics simulation computer program (SPECS) was developed to fill this need. The program simulates the fluid flow, thermal, and electrical characteristics of a system of components on a quasi-steady state basis for a variety of energy conversion systems. A unique approach is used in which the set of characteristic equations is solved by the Newton-Raphson technique. This approach eliminates the tedious iterative loops which are found in comparable programs such as TRNSYS or SOLTES-1. Several efficient features were also incorporated such as the centralized control and energy management scheme, and analogous treatment of energy flow in electrical and mechanical components, and the modeling of components of similar fundamental characteristics using generic subroutines. Initial tests indicate that this model can be used effectively with a relatively small number of time steps and low computer cost.

Hughes, R. D.↗

Flight dynamics analysis and simulation of heavy lift airships. Volume 2: Technical manual

The mathematical models embodied in the simulation are described in considerable detail and with supporting evidence for the model forms chosen. In addition the trimming and linearization algorithms used in the simulation are described. Appendices to the manual identify reference material for estimating the needed coefficients for the input data and provide example simulation results.

Ringland, R. F.↗

Flight dynamics analysis and simulation of heavy lift airships. Volume 3: User's manual

The User's Manual provides the basic information necessary to run the programs. This includes descriptions of the various data files necessary for the program, the various outputs from the program and the options available to the user when executing the program. Additional data file information is contained in the three appendices to the manual. These appendices list all input variables and their permissible values, an example listing of these variables, and all output variables available to the user.

Emmen, R. D.↗