Results for “Digital image correlation” — Page 19

NASA NTRSDate not supplied

RESIDUAL DEFORMATION ANALYSIS IN COMPOSITE SHELL STRUCTURES MANUFACTURED USING AUTOMATED FIBER PLACEMENT

The manufacturing of composites typically produces residual stresses that can significantly affect the final shape of the structure. The process of automated fiber placement (AFP) has become a prominent manufacturing technique in developing layups with tailored, variable stiffness morphology. The steered patterns of fiber tows with and without overlaps produce residual deformations that are distinctive from traditional layups. Digital image correlation was used to measure the AFP lamina coefficients of thermal expansion, which were incorporated into finite element analyses (FEA) to model the cooling phase of the cure cycle. The effects of nonlinear analysis and temperature-dependent lamina properties calculated using self-consistent field micromechanics, on the resulting residual deformation of shells, were also modeled. The predicted residual deformation was analyzed by considering out-of-roundness in cylindrical shells and compared to the experimental results. The shell FEA results were well-correlated with the overall deformed shape of the AFP cylinder with overlaps, while the shell FEA model of the AFP cylinder without overlaps did not show as good of qualitative match of the deformation pattern. Analytical correlation with measured results were insensitive to material softening at elevated temperatures, geometric nonlinearities, and variations in measured lamina thermal properties. To improve the accuracy of the residual deformation analysis, these results suggest that the thermo-chemical shrinkages preceding the cooldown should be considered, as well as possible variations in ply level microstructure due to the presence of the embedded fiber tow gaps and overlaps.

Composites↗

NASA NTRS2020

Bioinspired multilayered cellular composites with enhanced energy absorption and shape recovery

Inspired by the multiscale configuration of the microstructure of cork, the paper describes the design, 3D printing, and evaluation of a new type of multilayered cellular composite (MCC) structure composed of hard brittle and soft flexible phases. The mechanical behavior of 3D printed MCC structures have been investigated both experimentally and numerically. The experiments show that the MCC structure absorbs four times the amount of energy of a conventional cellular configuration under compressive strains up to 70%. Finite element simulations and 2D digital image correlation (DIC) also show that the multilayered architecture provides a more uniform strain distribution and higher stress transfer efficiency, with a resulting progressive failure mode rather than a catastrophic one. Cyclic loading tests demonstrate that the MCC structure also possesses exceptional shape recoverability under compressive deformations up to 40%. These remarkable performance characteristics result from synergies between the properties of the two constituent materials and the chosen multilayered cellular microstructure. The soft phase, in particular, plays a pivotal role in absorbing elastic energy during loading and then releasing the stored energy while unloading. The volume fraction of the soft phase is also essential to control energy absorption and the transition of failure modes. The deformation mechanisms demonstrated here are robust and applicable to other architected cellular materials across multiple length scales and suggest new ways to design lightweight and high-resilience structural materials.

bioinspired composites↗

NASA NTRS2020

Analysis of Open Hole Compression Specimens Using the CompDam Continuum Damage Mechanics Model

This report documents a validation study on the standard Open Hole Compression (OHC) laminate test specimen conducted as part of the NASA Advanced Composites Project (ACP). Tests were conducted on OHC specimens with hard, quasi-isotropic, and soft layups using digital image correlation and X-Ray computed tomography to capture the structural response and damage evolution. Progressive damage models were constructed for use with the CompDam continuum damage mechanics code following the best practices established during the ACP. Detailed interrogation of the analysis results and comparison with experimental measurements provide a basis for assessing the capability of the modeling approach for OHC. The structural response is found to be captured well, with strengths predicted within 3\% of the experimental values for hard and quasi-isotropic laminates. In the soft laminate, the model predicts failure to be more brittle than the nonlinear, ductile response that was measured. Damage states extracted from the models at the same load level as test measurements are overlaid to show directly the similarities and differences between test and analysis results. Studying the damage evolution predicted by the analysis reveals that the failure process is a competition between fiber damage and delamination/sub-laminate buckling, with fiber damage dominating the collapse in the hard laminate and sub-laminate buckling governing in the soft laminate. Finally, a series of parametric studies varying numerical solution parameters (mesh size, mass scaling) and physical properties (fiber direction compressive strength and toughness) reveal sensitivities and deficiencies of the model. To the authors' knowledge, this study is the first for OHC specimens to include detailed evaluation of damage mode interactions, direct overlay of predicted and measured damage states, and sensitivity of the predicted results to difficult-to-measure fiber direction material properties.

Continuum damage mechanics↗

NASA NTRSDate not supplied

Experimental Observations of Damage States in Unnotched and Notched 3D Orthogonal Woven Coupons Loaded in Tension

This paper describes a series of unnotched and notched tensile tests on two 3D orthogonal woven architectures. Dog bone specimens were used for the unnotched tests, and open-hole specimens were used for the notched tests. For each architecture and test type, two specimens were loaded under monotonic displacement control to failure and two specimens were incrementally loaded to failure in five steps. X-ray computed tomography (CT) was used to characterize the woven architecture and defects on each specimen prior to testing. Digital image correlation (DIC) images were obtained from both sides of the specimen throughout the loading and unloading. Acoustic emission (AE) data were also continuously acquired throughout the loading. For the incremental tests, X-ray CT was used to document the damage progression after each load increment. The damage progression was analyzed based on the results from these three techniques. The results for both architectures and test specimens followed a pattern where matrix cracks formed at the surface perpendicular to the tensile load direction. New surface cracks formed continuously throughout the loading and cracks extended in depth and width. In general, fiber failure was not detected until specimen failure.

Wade C Jackson↗

NASA NTRSDate not supplied

Analysis of a Dynamic Flexed Flat Cable Harness

A dynamic flex test was performed on a spacecraft instrument harness composed of multiple individual flex cables, with each flex cable containing multiple copper traces. The purpose of the test was to demonstrate the capability of the harness to survive the number of expected flex cycles during the planned mission with appropriate margin. However, during testing, increased trace resistances and open circuits were observed beginning at approximately 10% of the total number of planned flex cycles. This paper discusses the various proximate causes that contributed to increased and open resistance in the flex cables and the subsequent redesign, manufacturing, reliability, and quality-related changes that were instituted. An analysis process, including failure analysis, non-destructive evaluation, digital imaging correlation, and parametric modeling, will also be discussed. The paper will cover the development of a robust dynamic flex harness design and include recommendations to extend flex harness life; make changes to the flex harness life test; and improve flex cable manufacturing, quality, and reliability.

Flexible PCB↗

NASA NTRSDate not supplied

Finite Element Analysis Validation for Stitched, Blade-Stiffened Aerospace Structures

Increased performance and manufacturing rates for aircraft or spacecraft structures may be achieved using stitched and resin infused composite structures. In order to carry out design and analysis of stitched composites, 2-dimensional (2-D) and 3-dimensional (3-D) modeling approaches for stitched and non-stitched carbon fiber vacuum-infused parts were developed. These analysis approaches will be compared with data from previous test specimens tested at the NASA Langley Research Center (LaRC) under tension and bending load conditions. The preliminary results presented herein for the 2-D and 3-D models capture the strain patterns observed in digital image correlation (DIC) data for stitched, blade-stiffened specimens tested in either tension or bending. The analysis method study presented for these specimens is part of a larger analysis development effort planned for stitched composites, with the modeling practices developed here contributing to those that may be applied to a new set of blade- stiffened test specimens that are currently being manufactured for testing as well as the design of a blade stringer pull-off test. These future tests are expected to provide opportunities to validate the developed modeling approaches for predictive purposes, and to provide opportunities for further refinement of the modeling approaches.

HiCAM↗

NASA NTRSDate not supplied

Experimental Observations of Damage States in Unnotched and Notched 3D Orthogonal Woven Coupons Loaded in Tension

This paper describes a series of unnotched and notched tensile tests on two 3D orthogonal woven architectures loaded in the warp direction. Dogbone specimens were used for the unnotched tests, and open-hole specimens were used for the notched tests. For each architecture and test type, two specimens were loaded under monotonic displacement control to failure, and two specimens were incrementally loaded to failure in five steps. X-ray computed tomography (CT) was used to characterize the woven architecture and defects on each specimen prior to testing. Digital image correlation (DIC) images were obtained from both sides of the specimen throughout the loading and unloading. For the incremental tests, X-ray CT was used to document the damage progression after each load increment. The results for both architectures and test specimens followed a similar pattern where matrix cracks formed perpendicular to the load direction and were primarily located between the stacks of warp tows. Two-piece failure path always occurred perpendicular to the loading direction, along the through-thickness segments of the Z-tows. The combination of stress concentrations due to the specimen geometry, weave geometry, and cut tows created stress concentrations that appear to initiate failure.

Woven materials↗

NASA NTRSDate not supplied

Analysis of a Dynamic Flexed Flat Cable Harness

A dynamic flex test was performed on a spacecraft instrument harness composed of multiple individual flex cables, with each flex cable containing multiple copper traces. The purpose of the test was to demonstrate the capability of the harness to survive the number of expected flex cycles during the planned mission with appropriate margin. However, during testing, increased trace resistances and open circuits were observed beginning at approximately 10% of the total number of planned flex cycles. This paper discusses the various proximate causes that contributed to increased and open resistance in the flex cables and the subsequent redesign, manufacturing, reliability, and quality-related changes that were instituted. An analysis process, including failure analysis, non-destructive evaluation, digital imaging correlation, and parametric modeling, will also be discussed. The paper will cover the development of a robust dynamic flex harness design and include recommendations to extend flex harness life; make changes to the flex harness life test; and improve flex cable manufacturing, quality, and reliability.

Flexible PCB↗

NASA NTRSDate not supplied

In-situ Testing to Acquire HR-EBSD and DIC Strain Data Within a Coincident Domain

For this project, an inked rubber stamp was applied to a small Inconel 625 specimen. The stamp transferred a thin pattern with microscale features for digital image correlation (DIC). The pattern is easily visible at lower voltages and thin enough to not obstruct backscattered electrons. The unique characteristics of the pattern enabled the concurrent acquisition of DIC and high-resolution electron backscatter diffraction (HR-EBSD) data while the specimen was loaded in-situ. The challenges of in-situ testing and combining EBSD with DIC measurements are discussed. By combining the elastic strains (from HR-EBSD) and total strains (from DIC) the result of this approach is an estimate of stress- strain behavior at points across the specimen surface. This combined dataset can then be used as higher-fidelity data in the calibration of crystal plasticity models.

Will Gilliland↗

NASA NTRSDate not supplied

Effects of Cooling Holes on SiC/SiC Strength and Durability

Ceramic Matrix Composites (CMCs) such as SiC/SiC are currently operating in select high temperature components of turbine engines. When these materials are implemented in components at higher operating temperatures, film cooling may be necessary. Film cooling requires holes to be fabricated at appropriate locations within these components. This study examines the effect of cooling holes on SiC/SiC composite strength and durability. Mechanical test data on specimens with multiple holes is reported for isothermal conditions at room and elevated temperatures. Tools such as Digital Image Correlation (DIC) and Acoustic Emission (AE) are used to monitor strain and cracking upon loading.

Ceramic matrix composite↗

NASA NTRSDate not supplied

A Summary of Test Results from a NASA Lift + Cruise eVTOL Crash Test

On November 9, 2022, the National Aeronautics and Space Administration (NASA) conducted a full-scale crash test of the NASA Lift+Cruise (LPC) reference vehicle at the NASA Langley Research Center Landing and Impact Research Facility (LandIR) under combined vertical and horizontal impact conditions to simulate a severe but survivable crash. The LPC test article is a carbon-composite skin/frame structure design, developed and fabricated for the cabin section only. The test utilized various configurations of seats and Anthropomorphic Test Devices (ATDs, a.k.a. crash test dummies) intended to encompass a variety of occupant conditions. In addition, an in-house developed energy absorbing subfloor was utilized for the evaluation of load attenuation. Overhead mass was simulated using attached lifting hardware and other systems were simulated using ballast mass. The test article impacted the ground with velocities of 38.1 ft/s horizontal and 31.4 ft/s vertical. During the first approximately 38 milliseconds (ms), the cabin section experienced a large amount of acceleration on the belly which was attenuated by the subfloor structures and seats. Over the next approximately 160 ms, the test article experienced failure in the a-, b- and c-pillars, leading to a partial collapse of the overhead structure. Test data was collected on the belly, floors, seats, overhead mass, and tail. In addition, there was high speed full-field digital image correlation analysis data collected on the port side skin surface. Collected ATD data showed that the ATDs seated in the energy absorbing seats experienced loads at limits below the those in current regulations. Even without an energy absorbing seat, the energy absorbing subfloors crushed as intended, and limited the load on the large 95 th percentile ATD to 10% over suggested limits. The collapse of the roof did affect the 95 th percentile ATD, which showed high neck loading values due to head contact, whereas survivable volume was maintained for the other ATDs. While the energy absorbing subfloor and energy absorbing seats both contributed to occupant load attenuation, further optimization is suggested to increase their robustness.

evtol↗

NASA NTRSDate not supplied

Impact Ice Adhesion at NASA Glenn: Current Experimental Methods and Supporting Measurements

When examining the literature on the adhesion strength of impact ice, there have been a wide range of methodologies tried to measure the required stresses to induce interfacial delamination. Utilizing the Icing Research Tunnel at the NASA Glenn Research Center to generate the impact ice required for this work, several different mechanical tests have been and are being developed to determine the stresses along the interface between ice and coupon. This set of tests includes the technical mature modified lap joint test which has been used to conduct ice adhesion studies through a wide sweep of icing conditions. To conduct in situ ice adhesion measurements inside of the Icing Research Tunnel, several new experiments are currently being developed to make ice adhesion measurements during and immediately after ice accretion. In addition to these experimental methods, several supporting measurement techniques have been developed to allow for a better understanding on the influence of icing cloud conditions on the mechanical behavior of impact ice. Digital image correlation has been successfully implemented to augment the data generated by the modified lap joint test with full field surface displacement and strain measurements which allow for insight into the deformation processes present during a test. Both optical microscopy of impact ice samples along with ice replication techniques have been used to study the grain structure of the impact ice. This has led to a deeper understanding of the results from the modified lap joint method and how the structure of impact ice changes as it is accreted during an icing spray. The freezing process of impact ice generated by supercooled liquid water is not a volume conserving process, which leads to the presence of residual strains along the interface between ice and substrate. These strains have been observed using both a simplified flat geometry and a representative airfoil. The data gathered by these experimental adhesion methods and supporting measurements allows for a comprehensive understanding on the behavior of impact ice which will be critical to the development of future ice shedding models.

Ice Adhesion↗

NASA NTRSDate not supplied

Results from Two Full-Scale Hawker 4000 Fuselage Drop Tests

In the spring of 2022, NASA Langley Research Center (LaRC) conducted two full-scale drop tests on a Hawker 4000 partial fuselage structure for the evaluation of composite material response under dynamic impact loading conditions. The specific objectives of the tests were to induce dynamic composite damage initiation and progression and in primary structure and to understand the nature of the failure modes. The tests were conducted via dividing the fuselage hardware into three smaller sections. Dynamic drop tests were conducted on the forward and aft portions of the fuselage under different dynamic loading conditions, while the middle section was reserved for materials testing. Both tests were conducted by dropping the test articles from a height of 14 feet with significant amounts of pitch, which was added to initiate damage in specific regions of the structure. The test articles were ballasted then instrumented with accelerometers at various locations and speckle-coated on both exterior sides with a black and white stochastic pattern for use with three-dimensional digital image correlation (3D-DIC). In addition, the interior belly portion of the forward section test article was also speckle-coated, which was intended to capture deformations on the belly of the test article from the interior at impact. The interior of the aft section test article was not speckle-coated. Prior to testing, bow-tie markers were applied at various locations for use in marker tracking, to measure impact conditions such as vertical impact velocity and pitch. In this report, a partial summary of the data collected from the tests is presented. The data was primarily in the form of accelerometers to measure impact acceleration and 3D-DIC to measure deformation and failure onset and propagation. Post-test inspections revealed the primary damage mechanism was fiber cracking and delamination primarily in and around the area that contacted the impact surface. Acceleration pulse shapesin the ballast locations were trapezoidal in nature and ranged between 10 g and 40 g, depending on the location and test.

full scale testing↗

NASA NTRSDate not supplied

Impact Ice Adhesion at NASA Glenn: Current Experimental Methods and Supporting Measurements

When examining the literature on the adhesion strength of impact ice, there have been a wide range of methodologies tried to measure the required stresses to induce interfacial delamination. Utilizing the Icing Research Tunnel at the NASA Glenn Research Center to generate the impact ice required for this work, several different mechanical tests have been and are being developed to determine the stresses along the interface between ice and coupon. This set of tests includes the technical mature modified lap joint test which has been used to conduct ice adhesion studies through a wide sweep of icing conditions. To conduct in situ ice adhesion measurements inside of the Icing Research Tunnel, several new experiments are currently being developed to make ice adhesion measurements during and immediately after ice accretion. In addition to these experimental methods, several supporting measurement techniques have been developed to allow for a better understanding on the influence of icing cloud conditions on the mechanical behavior of impact ice. Digital image correlation has been successfully implemented to augment the data generated by the modified lap joint test with full field surface displacement and strain measurements which allow for insight into the deformation processes present during a test. Both optical microscopy of impact ice samples along with ice replication techniques have been used to study the grain structure of the impact ice. This has led to a deeper understanding of the results from the modified lap join method and how the structure of impact ice changes as it is accreted during an icing spray. The freezing process of impact ice generated by supercooled liquid water is not a volume conserving process, which leads to the presence of residual strains along the interface between ice and substrate. These strains have been observed using both a simplified flat geometry and a representative airfoil. The data gathered by these experimental adhesion methods and supporting measurements allows for a compressive understanding on the behavior of impact ice which will be critical to the development of future ice shedding models.

Ice Adhesion↗

NASA NTRSDate not supplied

A Summary of Test Results from a NASA Lift + Cruise eVTOL Crash Test

On November 9, 2022, the National Aeronautics and Space Administration (NASA) conducted a full-scale crash test of the NASA Lift+Cruise (LPC) reference vehicle at the NASA Langley Research Center Landing and Impact Research Facility (LandIR) under combined vertical and horizontal impact conditions to simulate a severe but survivable crash. The LPC test article is a carbon-composite skin/frame structure design, developed and fabricated for the cabin section only. The test utilized various configurations of seats and Anthropomorphic Test Devices (ATDs, a.k.a. crash test dummies) intended to encompass a variety of occupant conditions. In addition, an in-house developed energy absorbing subfloor was utilized for the evaluation of load attenuation. Overhead mass was simulated using attached lifting hardware and other systems were simulated using ballast mass. The test article impacted the ground with velocities of 38.1 ft/s horizontal and 31.4 ft/s vertical. During the first approximately 38 milliseconds (ms), the cabin section experienced a large amount of acceleration on the belly which was attenuated by the subfloor structures and seats. Over the next approximately 160 ms, the test article experienced failure in the a-, b- and c-pillars, leading to a partial collapse of the overhead structure. Test data was collected on the belly, floors, seats, overhead mass, and tail. In addition, there was high speed full-field digital image correlation analysis data collected on the port side skin surface. Collected ATD data showed that the ATDs seated in the energy absorbing seats experienced loads at limits below the those in current regulations. Even without an energy absorbing seat, the energy absorbing subfloors crushed as intended, and limited the load on the large 95 th percentile ATD to 10% over suggested limits. The collapse of the roof did affect the 95 th percentile ATD, which showed high neck loading values due to head contact, whereas survivable volume was maintained for the other ATDs. While the energy absorbing subfloor and energy absorbing seats both contributed to occupant load attenuation, further optimization is suggested to increase their robustness.

evtol↗

NASA NTRSDate not supplied

Results from Two Full-Scale Hawker 4000 Fuselage Drop Tests

In the spring of 2022, NASA Langley Research Center (LaRC) conducted two full-scale drop tests on a Hawker 4000 partial fuselage structure for the evaluation of composite material response under dynamic impact loading conditions. The specific objectives of the tests were to induce dynamic composite damage initiation and progression and in primary structure and to understand the nature of the failure modes. The tests were conducted via dividing the fuselage hardware into three smaller sections. Dynamic drop tests were conducted on the forward and aft portions of the fuselage under different dynamic loading conditions, while the middle section was reserved for materials testing. Both tests were conducted by dropping the test articles from a height of 14 feet with significant amounts of pitch, which was added to initiate damage in specific regions of the structure. The test articles were ballasted then instrumented with accelerometers at various locations and speckle-coated on both exterior sides with a black and white stochastic pattern for use with three-dimensional digital image correlation (3D-DIC). In addition, the interior belly portion of the forward section test article was also speckle-coated, which was intended to capture deformations on the belly of the test article from the interior at impact. The interior of the aft section test article was not speckle-coated. Prior to testing, bow-tie markers were applied at various locations for use in marker tracking, to measure impact conditions such as vertical impact velocity and pitch. In this report, a partial summary of the data collected from the tests is presented. The data was primarily in the form of accelerometers to measure impact acceleration and 3D-DIC to measure deformation and failure onset and propagation. Post-test inspections revealed the primary damage mechanism was fiber cracking and delamination primarily in and around the area that contacted the impact surface. Acceleration pulse shapesin the ballast locations were trapezoidal in nature and ranged between 10 g and 40 g, depending on the location and test.

full scale testing↗

NASA NTRSDate not supplied

Impact Forces From Artificial and Real Birds on a Large Diameter Hopkinson Bar

Forces were measured from normal impacts with two different artificial bird recipes and two species of real birds on a very rigid flat surface. The tests were conducted by launching the soft body projectiles axially into a Hopkinson bar in accordance with the SAE AS6940 test standard at three different nominal impact conditions: (a) a 1 kg projectile at an impact velocity of 49 m/sec; (b) a 1.8 kg projectile at an impact velocity of 110 m/sec; and (c) a 1.8 kg projectile at an impact velocity of 310 m/sec. At each condition two artificial birds and one real bird projectile were tested with at least three test repeats. Simulations were conducted to assess the effects of projectile orientation and velocity on predicted forces. The Hopkinson bar consisted of an Aluminum 6061 solid cylindrical bar with a diameter of 305 mm and a length of 7.31 m, made up of two 3.66 m long sections that were in axial contact with each other. The bar was instrumented for strain measurement at two locations, 457.2 mm and 609.6 mm (1.5 and 2 diameters) from the impacted face. Forces were calculated from the measured strain. In addition, digital image correlation (DIC) was used to measure the velocity of the free end of the bar. The real bird projectiles were 1 kg Mallard ducks and 1.8 kg Golden Comet chickens that were prepared per ASTM F330-21. Prior to testing, the real birds were placed in muslin bags to minimize tumbling during flight. Two artificial bird formulations were tested, one produced by the University of Dayton Research Institute (UDRI) and the other by the German Aerospace Center, DLR. The UDRI projectile was a homogeneous, relatively soft solid, formulated with a mixture of water, gelatin and phenolic micro-balloons to achieve a nominal density of 0.95 g/cc. The DLR projectile consisted of a printed plastic shell with internal plastic ribs and filled with a gel material. The projectiles were designed such that the overall average density was the desired value of 0.95 g/cc. Initial testing showed that contact between the two Hopkinson bar segments was not sufficient to allow full transmission of the waves through the interface. For the 49 m/sec and 110 m/sec tests this resulted in reflections returning to the strain measurement site prior to the end of the impact. For these tests only a portion of the force pulse could be accurately measured. For the highest velocity tests at 310 m/sec the force pulse was complete by the time reflected waves interfered with the response. Despite this limitation, useful force data were obtained for all velocities. Impact forces were very sensitive to the impact orientation and velocity. The force history generally consisted of an initial region with varying amplitude followed by a relatively constant amplitude response. The steady state region was similar among all projectiles and similar to what would be predicted for an inviscid fluid with a density of 0.95 g/cc. The initial part of the force response exhibited varying degrees of test-to-test repeatability associated with each projectile type. Forces calculated from DIC velocity measurements of the free end of the bar compared favorably those from the strain measurements. In general, the artificial projectile impact forces were quite repeatable from test to test, with some exceptions which could be explained by issues associated with either the projectile itself or with how the projectile exited the gun barrel. For all impact velocities the initial portion of the impact force from the bird projectiles exhibited large test-to-test variability. In this paper, impact forces for three types of projectiles at three impact velocities will be presented with an emphasis on the test-to-test repeatability of the results. Based on test and simulation results a proposed method for normalizing the impact force to minimize effects of differences in projectile orientation, impact velocity and density will also be discussed.

Bird strike↗

NASA NTRSDate not supplied

High-Temperature Mechanical Tensile Testing of Unidirectional Sic/Sic Composites Using A Versatile Lamp Furnace

Silicon carbide (SiC) based ceramic matrix composites (CMCs) are of interest for high-temperature structural applications, including use in turbine engine components. To understand damage mechanisms and predict durability of these systems, in-depth knowledge of their behavior at ambient and high temperatures is necessary. A method for high temperature testing of SiC/SiC minicomposite specimens up to 1500oC in both tensile fast fracture and creep conditions to investigate their thermomechanical behavior will be presented. This method utilizes a novel radiation heat furnace, equipped with infrared lamps with ellipsoidal reflectors, to heat the specimen at the furnace center in user-defined atmospheres. The housing structure of the lamps allows for observation of the specimen during testing using optical methods and for conducting other experimental studies. The goal is to employ nondestructive health monitoring techniques in-situ, including acoustic emission (AE), electrical resistance (ER), and digital image correlation (DIC) to evaluate damage initiation and evolution in the minicomposite specimens during tensile testing. Results from mechanical testing and nondestructive techniques will be presented. Electron microscopy and X-ray micro-computed tomography were used to further characterize specimen damage after testing.

Aeronautics↗