Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Detonators”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS2012

Performance Impact of Deflagration to Detonation Transition Enhancing Obstacles

A sub-model is developed to account for the drag and heat transfer enhancement resulting from deflagration-to-detonation (DDT) inducing obstacles commonly used in pulse detonation engines (PDE). The sub-model is incorporated as a source term in a time-accurate, quasi-onedimensional, CFD-based PDE simulation. The simulation and sub-model are then validated through comparison with a particular experiment in which limited DDT obstacle parameters were varied. The simulation is then used to examine the relative contributions from drag and heat transfer to the reduced thrust which is observed. It is found that heat transfer is far more significant than aerodynamic drag in this particular experiment.

Paxson, Daniel E.↗
NASA NTRS2019

Operational Stability Limits in Rotating Detonation Engine Numerical Simulations

An instability is described which arises in computational fluid dynamic (CFD) simulations of semi-idealized rotating detonation engines (RDE) configured with a throat at the exit. Its existence is verified by examining output from two independently developed CFD codes simulating the same configuration and producing solutions that agree well. The instability is shown to be thermo-acoustic in that a spatial integral of the product of pressure and heat release fluctuations develops a regular oscillation which grows in time. The instability can become severe enough to cause detonation failure. Its onset is shown to be closely linked to the size of the exit throat and the size of the inlet restriction; both parameters that strongly influence RDE performance. It is shown that the instability places a cap on ideal RDEperformance, but that an optimized exhaust throat and inlet restriction combination still yields substantial pressure gain. Other parametric sensitivities are also examined in terms ofinstability growth. These include axial length, inlet manifold pressure, and air-fuel ratio.

Paxson, Daniel E.↗
NASA NTRSDate not supplied

Heat Transfer Measurements of NASA Liquid Kerosene/Oxygen Rotating Detonation Rocket Engine

The RDRE has been identified as a viable high performance propulsion system with numerous advantages over the state-of-the-art (SOA) liquid rocket engine. NASA has been investigating this combustion device for applications ranging from lander, upper stage, thruster, and hypersonics. All of the activities funded to date have been focused on closing major technology gaps preventing the RDRE from being used more broadly by industry. One of those gaps include the prediction and management of heat transfer to the walls from the extreme combustion environment. This work overviews the heat transfer measurements made using new and existing hardware. A liquid oxygen / liquid RP-1 RDRE was tested utilizing a calorimeter outer body and outer body nozzle extension. An actively cooled inner body with axial running cooling channels was also used. A bimetallic GRCop-42 / Monel K500 injector was developed and demonstrated to be a viable technology for RDRE environments. Trends in bulk heat loads are discussed along with a direct comparison to constant pressure theory predictions of wall heat transfer. The experimental data obtained in this investigation showed similar heat fluxes to constant pressure theory indicating deflagration may have dominated the flow field. Only a single detonation wave was observed in all tests which imparted a significant dynamic load (vibration) on the test article making measurement of combustor performances extremely challenging. Both accelerometer and load cell data corroborate the extreme G-forces measured. The single wave mode yielded relatively low performances compared with other hot fire test data sets available. This leads to the conclusion that a single detonation wave in this geometry is not sufficient for high performance. Wave multiplicity, or rather, a specific number of waves may yield higher performances.

Thomas Teasley↗
DOE OSTI2021

Computational Fluid Dynamics Combustion Modeling for Rotating Detonation Engines

This paper focuses on the development and validation of a combustion model for Computational Fluid Dynamics (CFD) modeling of Rotating Detonation Engines. A zero-dimensional Partially Stirred Reactor (PaSR) with a detailed chemical kinetic mechanism for hydrogen and air is used to model turbulent combustion. The model is computationally efficient and is based on the notion of partial mixing at the sub-grid level with turbulent exchange between mixed and unmixed regions. The ability of the PaSR model to accurately represent both detonative and deflagrative combustion is assessed by validating the results against experimental data. The effects of mesh resolution on the solution are also studied in order to determine if a mesh independent solution is obtainable with the Large Eddy Simulation (LES) approach to modeling turbulence. A comparison is made between the PaSR model and simply ignoring turbulence chemistry interactions which assumes that all species are perfectly mixed at the sub-grid level.

Strakey, Peter↗
DOE OSTI2021

Opto-thermal laser detonator

An opto-thermal laser detonator uses resonantly absorptive tuned nano-material associated with secondary explosives for optical absorption and initiation by an integral laser diode. The opto-thermal laser detonator includes main explosive material; resonantly absorptive tuned nano-material; secondary explosive material, wherein the resonantly absorptive tuned nano-material and the secondary explosive material are associated to form associated material made of the resonantly absorptive tuned nano-material and the secondary explosive material; and a laser diode operatively connected to the associated material, wherein the laser diode initiates the associated material which in turn initiates the main explosive material.

Wilkins, Paul R.↗
DOE OSTI2021

Design and Testing of a Water-Cooled Rotating Detonation Combustor at Elevated Operating Pressures - Abstract

This is an extended abstract being submitted for consideration that briefly describes the material that will be included in the final paper. This study will detail the design and testing of a water-cooled Rotating Detonation Combustor (RDC) that permits operation for extended periods of time ensuring that the device has reach a stable operating temperature. Extended run times also provides an opportunity to consider transient behaviors that occur as a result of altering the operating conditions such as equivalence ratio. The experimental setup is also unique in that it consists of a ducted exhaust with a downstream high-temperature valve that can control the pre-combustion pressure in the RDC independent of the combustor annulus and exit geometry. This paper will examine the results from the extended operation of the water-cooled RDC over a range of both transient and steady state equivalence ratios (0.5 - 1.0), pre-combustion operating pressures (0 - 207 kPa), mass flow rates (0.42 – 0.5 kg/sec) and air inlet throat area to combustor channel area ratios (0.09 – 0.32). All tests were performed while operating on hydrogen in air at a nominal air inlet temperature of 340 – 350 K. Limited data obtained at an elevated inlet air temperature of 480 K will also be discussed. Results suggest that under certain conditions the operating mode of the detonation wave can vary as it approaches a stable operating temperature. For the RDC tested, a stable operating temperature is not achieved until approximately 8-10 seconds of run time.

Ferguson, Donald↗
DOE OSTI2023

Opto-thermal laser detonator

An opto-thermal laser detonator uses resonantly absorptive tuned nano-material associated with secondary explosives for optical absorption and initiation by an integral laser diode. The opto-thermal laser detonator includes main explosive material; resonantly absorptive tuned nano-material; secondary explosive material, wherein the resonantly absorptive tuned nano-material and the secondary explosive material are associated to form associated material made of the resonantly absorptive tuned nano-material and the secondary explosive material; and a laser diode operatively connected to the associated material, wherein the laser diode initiates the associated material which in turn initiates the main explosive material.

Wilkins, Paul R.↗
DOE OSTI2025

Outflow Boundary Conditions for Turbine-Integrated Rotating Detonation Combustors

This study examines outflow boundary conditions (BCs) in computational fluid dynamics (CFD) simulations of a transition duct with and without guide vanes that converts supersonic flow exiting a rotating detonation combustor (RDC) to subsonic flow to drive a turbine. Since the flow exiting the transition duct has swirling shock waves with significant spatial and temporal variations in pressure, temperature, and Mach number, imposing proper BCs poses a challenge. To ensure all swirling shock waves exit the transition duct without creating non-physical reflected waves at its outlet, this study examined three outflow BCs: (1) the average pressure imposed at the duct’s outlet, (2) a nonreflecting BC (NRBC) with a specified average pressure imposed at the duct’s outlet, (3) the average pressure imposed at the outlet of an extension duct made up of a buffer layer and a sponge layer. This study is based on the three-dimensional, unsteady density-weighted-ensemble-averaged continuity, Navier–Stokes, and energy equations for a thermally perfect gas closed by the realizable k–ε model and “enhanced” wall functions. The results obtained show that imposing an average pressure at the transition duct’s outlet produces spurious waves that degrade the physical meaningfulness of the solution. When the NRBC was applied, swirling shock waves exited the duct’s outlet without creating spurious waves. However, its usage requires the gas to be thermally, as well as calorically, perfect, which this study shows could be a concern. By imposing the average pressure at the outlet of an extension duct, the gas does not need to be calorically perfect. The results obtained show the effects of the sponge layer’s length and coarsening ratio on damping nonuniformities in non-physical reflected waves to ensure the flow exiting the transition duct’s outlet can do so as if there are no boundaries present and has the desired average pressure—even though the BC is applied at the extension duct’s outlet.

gas turbines↗
NASA NTRS1965

Steady detonations in gaseous ozone.

Steady detonation wave velocity in gaseous ozone in tubes of various diameters at initial pressure range and in mixtures with oxygen or argon

DETONATION WAVE↗
NASA NTRS1929

Impact waves and detonation. Part I

Among the numerous thermodynamic and kinetic problems that have arisen in the application of the gaseous explosive reaction as a source of power in the internal combustion engine, the problem of the mode or way by which the transformation proceeds and the rate at which the heat energy is delivered to the working fluid became very early in the engine's development a problem of prime importance. The work of Becker here given is a notable extension of earlier investigations, because it covers the entire range of the explosive reaction in gases - normal detonation and burning.

DETONATION↗
DOE OSTI2021

Simulation of flame acceleration and deflagration-to-detonation transition with heat transfer in HE product and fractured HE

A simple heat transfer model has been developed for high explosives. For the gaseous high explosive (HE) product, the Smargorinsky eddy viscosity model has been adopted for estimating the turbulent thermal conductivity. Convective heat transfer in the fractured solid HE is modeled as the effective thermal conduction in the porous media, which is equivalent to the enthalpy flux carried by the velocity determined by Darcy’s law with Forchheimer term.Other features of the model include a multi-reaction chain, equation-of-state for each species involved, and a two-phase hotspot model. Test calculations are performed with various initial disturbances. Onset and progress of flame acceleration (FA) and chemical reactions are strongly affected by the heat transfer and initial disturbance. Staged development of FA also affirms the necessity of modeling based on a multi-reaction chain. When conditions warrant,e.g., stronger initial disturbance, FA evolves to deflagration-to-detonation transition (DDT),demonstrating automatic capture of the DDT.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗