Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Degradation Rate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Opportunities to Update the Model of Tank Closure Grout Aging (SRNL-STI-2012-00404) Based on Experimental Results by the Savannah River Ecology Laboratory

The purpose of this report was to review the results of experiments on evolution of tank grout pore fluids performed by the Savannah River Ecology Laboratory (SREL) and reported in Seaman et al. (2020) and highlight opportunities for updating the model of tank grout degradation presented in Denham and Millings (2012). The SREL experimental results validate some assumptions used in the 2012 grout degradation model and provide information useful for updating the model. All experiments on tank grout degradation have limitations because of reaction rates and the enormous disparity between duration of the experiments and the duration of the degradation of the real tank grout system. Given these limitations, the experimental results form the basis for several recommendations for updating the grout degradation model described in this report.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Ion Chromatography and Combustion Ion Chromatography Analysis of Fuel Cell Effluent Water During Open Circuit Voltage

Open circuit voltage tests were conducted on sixteen 3M Ionomer and eight Nafion™ NR211 membranes. Lifetime distributions were determined, and ion chromatography (IC) techniques were used to measure fluoride, sulfate, trifluoro acetate, and oxalate ions. Combustion Ion Chromatography (CIC) was used to determine the total organic fluoride (TOF) associated with water soluble membrane degradation fragments. The ratio of these products relative to the fluoride release rates were used to infer the likely degradation mechanism for each membrane. Peroxide attack at the sulfonic acid side chain was determined to be the least relevant reaction pathway while the long-proposed polymer chain end unzipping appears to be the dominant mechanism. Abstraction of the tertiary fluorine in the NR211 backbone and side chain is evident by organic fluoride release rates higher than can be explained by unzipping alone.

25 ENERGY STORAGE↗
DOE OSTI2026

3D-Bioprinted Marine Bacteria for the Degradation of Polyhydroxybutyrate Bioplastics

The severe, long-lasting harm caused by plastic pollution to marine ecosystems and coastal economies has led to the development of biodegradable plastics; however, their limited decomposition in marine environments remains a challenge. Here, technologies are presented for creating 3D-bioprinted living materials as a proof of concept for bioplastic degradation, with specific use in marine environments. The approach developed here integrates the halotolerant bioplastic-degrading bacterium Bacillus sp. NRRL B- 14911 into alginate-based bio-ink to print an engineered living material (ELM) termed a “bio-sticker.” Quantification of bacteria viability reveals that bioprinted marine bacteria survive within biostickers for more than 3 weeks. The rate at which the biostickers degrade the bioplastic polyhydroxybutyrate (PHB) can be tuned by altering biosticker biomass concentration, bioplastic concentration, or incubation temperature. Biostickers that are transferred to a different PHB sample still retain high biodegradation activity, demonstrating their reusability. Strain sweep oscillatory tests demonstrate that the biostickers display predominantly viscoelastic behavior. Monotonic tensile tests indicate that the elastic modulus and the adhesion of the biostickers are not negatively impacted by bacteria growth or incubation temperature. This work paves the way for the development of ELMs to facilitate the inclusion of bioplastics within the blue economy, promoting the emergence of more sustainable and ecofriendly materials.

3D bioprinting↗
DOE OSTI2024

Nitrogen‐Nitrogen Bond Breaking in Irradiation Products of Hexanitrohexaazaisowurtzitane (CL‐20)

While the primary result of an interaction of ionizing radiation with an organic material is the ejection of electrons from molecular orbitals producing cations, the free electrons can further interact, yielding excited states; and, potentially, anions. In this work, we computed reaction barriers and energies for N−N bond breaking in the CL-20 cation, anion, and excited state to investigate if CL-20 degradation is accelerated after radiation exposure. We focused on N−N bond dissociation because it is the rate-determining step in the thermal degradation of CL-20. We found that N−N cleavage rapidly takes place in the CL-20 cation and anion with greatly reduced reaction energies as compared to CL-20. We also outlined a potential path for photodissociation of the N−N bond. While CL-20 is kinetically stable, initial degradation occurs readily in its irradiation products. In conclusion, this is of importance for the performance of the explosive after high-dose exposure and influences aging if CL-20 is irradiated at a low dose over extended periods of time.

CL-20 anion↗
DOE OSTI2026

Molecular concentration field design using closed-form steady-state solutions

Control over spatial concentration fields represents a fundamental challenge in designing synthetic biological systems and programmable soft materials. While nature creates morphogen gradients that orchestrate complex developmental processes, synthetic approaches have largely relied on empirical optimization and computationally intensive simulations. Here, we present an analytical framework for steady-state concentration fields generated by finite-sized localized sources in diffusion–degradation systems and derive closed-form solutions for one-, two-, and three-dimensional geometries. By expressing these solutions in dimensionless form, we show that gradient steepness and spatial structure are organized by the Thiele modulus, which captures the competition between diffusion and degradation length scales. The analysis reveals distinct design regimes: in degradation-dominated systems, gradient shape is governed by exponential decay and becomes dimension-independent, whereas in diffusion-dominated systems, gradient magnitude and extent follow dimension-dependent power-law scaling. Building on these results, we introduce a quantitative design strategy that uses threshold-based criteria to program concentration ranges by tuning physically accessible parameters, most directly the production rate, while holding transport and degradation properties fixed. Comparisons with numerical solutions and reported experimental systems demonstrate consistency with the predicted scaling behavior. Together, this work provides a generalizable and physically transparent framework for designing steady-state concentration fields in synthetic biological and soft matter systems, enabling predictive control of gradient-mediated organization without reliance on extensive numerical optimization.

Kim, Dong Woo [Johns Hopkins University, Baltimore↗
DOE OSTI2021

Simulation of hardened cement degradation and estimation of uncertainty in predicted failure times with peridynamics

Modeling the degradation of cement-based infrastructure due to aqueous environmental conditions continues to be a challenge. In order to develop a capability to predict concrete infrastructure failure due to chemical degradation, here we created a chemomechanical model of the effects of long-term water exposure on cement paste. The model couples the mechanical static equilibrium balance with reactive–diffusive transport and incorporates fracture and failure via peridynamics (a meshless simulation method). The model includes fundamental aspects of degradation of ordinary Portland cement (OPC) paste, including the observed softening, reduced toughness, and shrinkage of the cement paste, and increased reactivity and transport with water induced degradation. This version of the model focuses on the first stage of cement paste decalcification, the dissolution of portlandite. Given unknowns in the cement paste degradation process and the cost of uncertainty quantification (UQ), we adopt a minimally complex model in two dimensions (2D) in order to perform sensitivity analysis and UQ. We calibrate the model to existing experimental data using simulations of common tests such as flexure, compression and diffusion. Then we calculate the global sensitivity and uncertainty of predicted failure times based on variation of eleven unique and fundamental material properties. We observed particularly strong sensitivities to the diffusion coefficient, the reaction rate, and the shrinkage with degradation. Also, the predicted time of first fracture is highly correlated with the time to total failure in compression, which implies fracture can indicate impending degradation induced failure; however, the distributions of the two events overlap so the lead time may be minimal. Extension of the model to include the multiple reactions that describe complete degradation, viscous relaxation, post-peak load mechanisms, and to three dimensions to explore the interactions of complex fracture patterns evoked by more realistic geometry is straightforward and ongoing.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Co-Pyrolysis of Chicken and Cow Manure

Conventional pyrolysis is a relatively simple way for biochar production; however, a single biomass feedstock approach is not promising for the development of multiple properties of biochar used in various applications. Here, this study provides a detailed comparison in terms of pyrolysis kinetics between the cow manure and chicken manure, in addition to the co-pyrolysis by mixing the two livestock at different ratios. Eight different heating rates were tested, 5–40 °C/min with 5 °C/min step, on both livestock using the nitrogen as a gas agent with a flowrate of 50 ml/min. The initial results show that for the slow heating rates, 5 °C/min, the thermal degradation of the cow manure is different compared to that obtained from chicken manure. For the cow manure, the first peak, associated with hemicellulose decomposition, is higher than the second peak, associated with cellulose decomposition, which is the other way around for chicken manure. At 5 °C /min, the hemicellulose decomposition took place at 250 °C and 300 °C for the chicken manure and cow manure, respectively. The cellulose decomposition was started at 300 °C for chicken manure and 470 °C for cow manure. The lowest heat rate was selected for the co-pyrolysis case study to allow a quasi-equilibrium state to avoid measurement errors and heat transfer limitation in terms of thermal lag. Co-pyrolysis is studied with different blend ratios between the chicken and cow manure, where the 40% cow manure shows a positive result in terms of keeping an exothermic reaction over the co-pyrolysis process.

09 BIOMASS FUELS↗
DOE OSTI2022

Effect of metal/dielectric substrates on photopolymerization of BITh thin films

Abstract We have studied effects of metal–dielectric substrates on photopolymerization of [2,2ʹ-Bi-1H-indene]-1,1ʹ-dione-3,3ʹ-diyl diheptanoate (BITh) monomer. We synthetized BITh and spin-coated it onto a variety of dielectric, metallic, and metal–dielectric substrates. The films were exposed to radiation of a UV–Visible Xe lamp, causing photo-polymerization of monomer molecules. The magnitude and the rate of the photo-polymerization were monitored by measuring the strength of the ~ 480 nm absorption band, which existed in the monomer but not in the polymer. Expectedly, the rate of photo-polymerization changed nearly linearly with the change of the pumping intensity. In contrast with our early study of photo-degradation of semiconducting polymer P3HT, the rate of photo-polymerization of BITh is getting modestly higher if the monomer film is deposited on top of silver separated from the monomer by a thin insulating MgF 2 layer preventing a charge transfer. This effect is partly due to a constructive interference of the incident and reflected light waves, as well as known in the literature effects of metal/dielectric substrates on a variety of spectroscopic and energy transfer parameters. At the same time, the rate of photopolymerization is getting threefold larger if monomer is deposited on Ag film directly and charge transfer is allowed. Finally, Au substrates cause modest (~ 50%) enhancement of both monomer film absorption and the rate of photo-polymerization.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A Low-Cost Iron-Based Current Collector for Alkaline Battery Electrodes

The use of three-dimensional porous nickel foam as the current collector of the nickel hydroxide electrode adds significantly to the cost of the nickel-based alkaline rechargeable batteries. Although iron is considerably less expensive than nickel, iron corrodes at the operating potential of the nickel hydroxide electrode. We have found that a 70–100 nm thick thermal coating of cobalt ferrite spinel protects the iron from corrosion. Such a coated iron substrate was found to be stable against corrosion even when polarized anodically at 10 mA cm -2 in 30% potassium hydroxide electrolyte for 1000 h. While the thermal coating of cobalt ferrite protected iron against corrosion, incorporation of lithium ions into the coating was found to enhance the electrical conductivity of the coating. XPS and EXAFS studies confirmed that the enhanced conductivity resulted from an increase in the population of Co 3+ in the ferrite spinel lattice. An inexpensive iron (steel) substrate protected by such a coating when used as a nickel hydroxide battery electrode exhibited a specific capacity of 0.25 Ah g -1 at C/5 discharge rate, comparable to a nickel hydroxide electrode based on a relatively expensive nickel foam substrate. The steel-based electrode also exhibited no noticeable degradation over 150 cycles at C/2 rate. This demonstration of a robust and economical steel substrate presents a unique opportunity for reducing the cost of the nickel hydroxide battery electrode in alkaline batteries

25 ENERGY STORAGE↗
DOE OSTI2022

Physics-Informed Neural Network Modeling of Li-Ion Batteries: Preprint

Li-ion batteries (LIB) are a promising solution to enable storage of intermittent energy sources due to their high energy density. However, LIBs are known to significantly degrade after about 1000 charge-discharge cycles. LIBs degrade following different degradation modes and at a rate that depends on the operating conditions (external temperature, load). To plan the installation of batteries, appropriate understanding and prediction capabilities of their lifecycle is needed. High-fidelity numerical models of LIBs such as the pseudo-two-dimensional (P2D) model have been shown to accurately represent the charge-discharge-cycle of an LIB given ac- curate choice of the physical parameters. Given the large number of P2D parameters, adjusting them using forward runs is intractable. This work describes the development of a physics-informed neural network (PINN) as a surrogate substitute of the P2D model that captures parameter dependence. The PINN is advantageous as it needs little to no data, and can naturally encode the dependence of every model parameter. Here, a specific training procedure is adopted to efficiently cover parameter space, handle model stiffness and enforce boundary conditions. The trained PINN is validated against numerical solutions of the P2D model, and its applicability to battery degradation modeling is discussed.

battery degradation↗
DOE OSTI2021

Microwave Synthesis of Spinel MgFe 2 O 4 Nanoparticles and the Effect of Annealing on Photocatalysis

Through microwave heating in ethanol and with subsequent annealing, crystalline MgFe 2 O 4 nanoparticles are produced rapidly and in high yields >99%. Under varied annealing temperatures, the degree of Mg and Fe site inversion changes the optical, electronic, and composition of the nanoparticles. Here, a small particle size of ~10 nm is achievable with the aid of an ammonium salt mineralizer that caps the particles during nucleation and growth. Particles with the lowest inversion parameter and limited sintering upon annealing (at 600 ºC) exhibit the greatest production of hydroxyl radicals under visible light illumination. As such, these particles also facilitate the degradation of methylene blue dye faster than those particles annealed at higher temperature and show a rate constant of 0.061 h –1 for degrading 10 ppm methylene blue with 10 mg catalyst.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Deconstruction of plant biomass by a Cellulomonas strain isolated from an ultra-basic (lignin-stripping) spring

Plant material falling into the ultra-basic (pH 11.5-11.9) springs within The Cedars, an actively serpentinizing site in Sonoma County, California, is subject to conditions that mimic the industrial pretreatment of lignocellulosic biomass for biofuel production. In this research, we sought to obtain hemicellulolytic/cellulolytic bacteria from The Cedars springs that are capable of withstanding the extreme alkaline conditions wherein calcium hydroxide-rich water removes lignin, making cell wall polysaccharides more accessible to microorganisms and their enzymes. We enriched for such bacteria by adding plant debris from the springs into a synthetic alkaline medium with ground tissue of the biofuel crop switchgrass (Panicum virgatum L.) as the sole source of carbon. From the enrichment culture we isolated the facultative anaerobic bacterium Cellulomonas sp. strain FA1 (NBRC 114238), which tolerates high pH and catabolizes the major plant cell wall-associated polysaccharides cellulose, pectin, and hemicellulose. Strain FA1 in monoculture colonized the plant material and degraded switchgrass at a faster rate than the community from which it was derived. Cells of strain FA1 could be acclimated through subculturing to grow at a maximal concentration of 13.4% ethanol. A strain FA1-encoded β-1, 4-endoxylanase expressed in E. coli was active at a broad pH range, displaying near maximal activity at pH 6-9. Discovery of this bacterium illustrates the value of extreme alkaline springs in the search for microorganisms with potential for consolidated bioprocessing of plant biomass to biofuels and other valuable bio-inspired products.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Smoothing tool design and performance during subaperture glass polishing

During subaperture tool grinding and polishing, overlaps of the tool influence function can result in undesirable mid-spatial frequency (MSF) errors in the form of surface ripples, which are often corrected using a smoothing polishing step. Here, in this study, flat multi-layer smoothing polishing tools are designed and tested to simultaneously (1) reduce or remove MSF errors, (2) minimize surface figure degradation, and (3) maximize the material removal rate. A time-dependent convergence model in which spatial material removal varies with a workpiece-tool height mismatch, combined with a finite element mechanical analysis to determine the interface contact pressure distribution, was developed to evaluate various smoothing tool designs as a function of tool material properties, thicknesses, pad textures, and displacements. An improvement in smoothing tool performance is achieved when the gap pressure constant, $\overline{h}$ (which describes the inverse rate at which the pressure drops with a workpiece-tool height mismatch), is minimized for smaller spatial scale length surface features (namely, MSF errors) and maximized for large spatial scale length features (i.e., surface figure). Five specific smoothing tool designs were experimentally evaluated. A two-layer smoothing tool using a thin, grooved IC1000 polyurethane pad (with a high elastic modulus, E pad =360 MPa ), thicker blue foam (with an intermediate modulus, E foam =5.3 MPa ) underlayer, and an optimized displacement (d t =1 mm ) provided the best overall performance (namely, high MSF error convergence, minimal surface figure degradation, and high material removal rate).

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Evidence for ionization damage in mid-wave infrared nBn detectors

The effects of 63 MeV proton and 60Co gamma irradiation on the operation of 4.3 μm cutoff nBn photodetectors are demonstrated separately, and both are shown to yield a total ionizing dose (TID) effect. The effect is shown here in an InAsSbBi nBn detector and has been observed in other bulk alloy nBn detectors, and is unusual as it is notably absent in superlattice nBn detectors. The non-antireflection coated detectors exhibit a pre-radiation quantum efficiency of 17% at 3.3 μm wavelength and a dark current density of 50 μA/cm2, or roughly 300× the Rule 07 expectation, at their ideal operating voltage of −0.4 V bias at 150 K. Step-wise proton irradiation and in situ measurement indicate that the dark current increases to about 400× Rule 07 at the highest proton dose level of 150 krad(Si) (9.10 × 1011 p+/cm2), while the quantum efficiency is degraded at a relatively faster rate than the majority of analogous detectors characterized by our lab. Both the photocurrent and dark current are also shown to exhibit a turn-on voltage magnitude reduction of 100 mV following either gamma or proton irradiation, a trend which is attributable to negative trapped charge at the barrier interface (TID effect). This theory is further supported by an observed capacitance density magnitude reduction with dose and affirmed with Silvaco TCAD simulations. Following both proton exposure and subsequent anneal and gamma exposure and subsequent anneal; dark current, photocurrent, and CV all approach their pre-radiation baseline values.

Physics↗
DOE OSTI2022

Reducing Spontaneous Orientational Polarization via Semiconductor Dilution Improves OLED Efficiency and Lifetime

Spontaneous orientational polarization (SOP) in the electron-transport layer (ETL) of organic light-emitting diodes (OLEDs) is increasingly recognized as a key factor influencing their performance. Here, we show that SOP is dramatically reduced in the common electron-transport material 2,2',2"-(1,3,5-benzinetriyl)-tris(1-phenyl-1-H-benzimidazole) by coevaporating it together with medium-density polyethylene. Eliminating SOP from the ETL of blue fluorescent OLEDs in this manner reduces their operating voltage by 0.5 V, increases their external quantum efficiency (EQE) by 30%, and leads to a threefold increase in device lifetime. We show that the EQE and lifetime improvements both originate from reduced exciton-polaron annihilation in the emissive layer, and that this leads to a functional relationship between the two quantities that can be used to quantify the rate of annihilation-induced degradation in the device. Furthermore, these results highlight a substantial opportunity to improve OLED performance by controlling SOP through semiconductor dilution and suggest that this capability can be used to systematically isolate and understand exciton-polaron degradation in the pursuit of stable blue OLEDs.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Experimental observations of amorphization in multiple generations of boron carbide

Boron carbide is an excellent armor material due to its light weight and ultrahigh hardness. However, high-rate mechanical behavior can be degraded by stress-induced amorphization. In this paper, we review the progressive advances in the understanding of amorphization in three successive generations of boron carbide: stoichiometric (undoped), B-rich, and B/Si codoped boron carbides. For each generation of boron carbide, the crystal structure and microstructure are first discussed. Then, we outline the experimental observations of amorphization made by Raman spectroscopy and transmission electron microscopy. The susceptibility of amorphization in each generation of boron carbide will be compared and the fundamental mechanisms that explain the reduction in amorphization for B-rich and B/Si codoped boron carbides elucidated. Furthermore, comments on future research directions to further broaden and deepen the understanding of stress-induced amorphization of boron carbide are also provided.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Development of a Modular, Crushed-Rock Thermal Energy Storage Pilot Design

The goal of this project, primarily funded by the U.S. Department of Energy, is to design a next-step pilot to advance near-term energy storage integrated with a fossil plant to provide a facility capable of being viable and effective in a market with growing penetration of variable renewable energy (VRE). Thermal energy storage (TES) represents an ideal technology for this purpose. The current effort will complete a feasibility study to prepare for the Phase II pre-front end engineering design (pre-FEED) for implementing a crushed-rock TES system integrated with a natural gas combined cycle (NGCC) plant. The crushed rock storage technology, which is being developed by Brenmiller Energy, is a modular TES system termed bGen™, which can accommodate both thermal and electrical inputs and output steam, hot water, or hot air. For this application, the estimated efficiency is 80% thermal to thermal. The TES technology is being designed to operate on a slipstream from NYPA’s Eugene W. Zeltmann Power Project (Zeltmann) natural gas combined cycle (NGCC) plant. The projected size of the system will be up to 4 MWe with at least 4 hours of storage duration, or 16 MWh-e total. Final sizing is being determined during the ongoing feasibility study. The next-step pilot being designed as part of the current project will represent a 5-fold increase in scale for this TES technology, and will be used to validate the technology’s ability to provide effective and economical energy storage. This pilot would represent the next-to-last demonstration scale before the technology could be commercial ready at GWh-e scales in the 2030 timeframe. This project is expected to design the critical next-step pilot, which will be undertaken in real-world operating conditions to better determine the crushed rock TES technology’s ability to be integrated with an NGCC plant and assess degradation over transient cycling at rates befitting various marketplaces. The crushed-rock TES pilot design is a technically feasible next step in the development of the technology and is built upon years of prior testing and demonstration. The proposed TES technology was developed by Brenmiller over the last 8 years and has been tested in 3 generations of demonstration units at various sites, globally. During this field testing, different characteristics and performance of the technology were validated, including the following key features: energy storage capacity, energy storage charge/discharge rate, energy storage loses, energy storage mechanical testing. This presentation will provide an update on the results of the conceptual design study for the modular crushed-rock TES system, integrated with a NGCC power plant.

03 NATURAL GAS↗
DOE OSTI2026

Automating Detection and Diagnosis of Faults, Failures, and Underperformance in PV Plants

The project developed hybrid physics-based and machine-learning methods for near-real-time detection of balance-of-system faults (e.g., string, combiner, and tracker outages) in utility-scale Photovoltaic plants, achieving over 50% true positive rates with under 10% false positives and significantly reducing engineering setup time. In the extended phase, the scope expanded to plant-level underperformance analysis and industry benchmarking through the SUPER.epri.com platform. SUPER standardizes data processing and performance metrics across more than 9 GWac and 120+ plants, enabling robust comparisons and insights into loss rates, inverter downtime, and capacity degradation.

14 SOLAR ENERGY↗