Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DOPES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Transition-metal doped titanate nanowire photocatalysts boosted by selective ion-exchange induced defect engineering

Defect engineering through elemental doping is an efficient way to boost the performance of semiconductor photocatalysts. For this work, transition-metal (TM) doped titanate nanowires (TNWs) were prepared via ion-exchange over the titanate precursors and demonstrated for the Rhodamine B (RhB) degradation under ultraviolet (UV) light irradiation. The ion-exchange of selective ions (V 5+ , Cr 3+ , Ni 2+ , and Zn 2+ ) with protons from pristine TNWs resulted in the hierarchical meso-porosity of nanowires with large pores of ~5–20 nm by TM doping and small pores of ~3.6–4.5 nm inherited from pristine TNWs, which facilitates the mass transfer while maintaining high surface area and active sites. Meanwhile, the TM intercalation partially reduces the Ti 4+ to Ti 3+ and narrows the optical bandgap, which, together with oxygen vacancies and superoxide radicals from pristine TNWs, enhance the adsorption and photocatalytic degradation performance of RhB. This work helps to elucidate the effects of transition-metal doping and provides a rational strategy towards high performance titanate-based photocatalysts for efficient and sustainable wastewater treatment.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Operando carbon corrosion measurements in fuel cells using boron-doped carbon supports

Carbonaceous materials are the most common catalyst supports in proton exchange membrane fuel cell (PEMFCs), yet their corrosion is one of the limiting factors in achieving high durability. Herein, we doped carbon supports with boron (B) to increase the corrosion-resistance of the support. Two types of B-doped carbons were synthesized and studied as platinum support materials. Further, they varied in their morphologies, surface areas, and the types of boron species. The durability of Pt/B-doped carbon catalysts was investigated using the US-DOE catalysts’ supports accelerated stress test (AST) and a mass-spectrometer connected to the fuel cell effluent stream to quantify the mass of corroded carbon support in operando. The addition of boron to the carbon increased the stability of Pt catalysts in long-term usage of PEMFC. After 4000 AST cycles, more than 50% of initial current density was preserved for the boron-containing systems, while less than 30% of it remained with Vulcan carbon (Pt/V). Also, the Pt/B-doped carbon samples demonstrated better electrochemical active surface area (ECSA) stability when compared to Pt/V. Carbon loss measurements showed that B-doped carbons have higher resistance to electrochemical corrosion than unmodified carbon. Specifically, the substitutional boron-doped carbon demonstrated an extremely high stability and low corrosion rate.

25 ENERGY STORAGE↗
DOE OSTI2021

Evaluation of electrochemical performance and redox activity of Fe in Ti doped layered P2-Na0.67Mn0.5Fe0.5O2 cathode for sodium ion batteries

Here, we report a wet synthesis-based titanium doping strategy to improve the structural stability and electrochemical performances, such as cycling stability and rate capability, of P2-type Na 0.67 Fe 0.5 Mn 0.5 O 2 layered oxide cathodes. Through Ti 4+ doping aimed at replacing some of the Mn and Fe atoms in the crystal structure, effective mitigation of the Jahn Teller distortion caused by active Mn 3+ before charging and Fe 4+ after charging was achieved. X-ray diffraction (XRD), Raman spectroscopy, Electrochemical Impedance Spectroscopy (EIS) and Mössbauer spectroscopy were used to investigate the effects of the Ti 4+ dopant before and after cycling. It was observed that Ti 4+ doping increased the Na layer thickness, minimized the lattice volume strain, showed better structural stability, minimally decreased Fe migration to the Na layer, and lowered charge transfer resistance in these P2-type cathodes. Overall, our reported synthesis methodology and electrochemical characterizations highlight the feasibility of Ti doping in sodium layered oxide P2-type cathodes.

25 ENERGY STORAGE↗
DOE OSTI2022

Chemical kinetic interactions and sensitivity analyses for 2-ethylhexyl nitrate-doped PRF91 using a reduced mechanism

A numerical and experimental investigation about the chemical kinetic interactions between 2-ethylhexylnitrate (EHN) and PRF91 was performed in this study. Rapid compression machine experiments were conducted to investigate the effect of EHN on the autoignition reactivity of the fuel, and a reduced chemical kinetic mechanism was developed including an EHN sub-model. Experiments showed that the ignition delay decreases as the fuel is doped with EHN, but the effect of the doping level of EHN on the ignition is highly non-linear. Moreover, experiments showed that the EHN effectiveness is lowest during the transition between the low-temperature regime and the negative temperature coefficient (NTC) regime, and it rapidly increases as the temperature increases. Both detailed and (developed) reduced mechanisms were validated against the experimental results, allowing a more in-depth EHN-fuel chemistry study. Additionally, ignition delay sensitivity and EHN effectiveness sensitivity analyses were performed with the reduced mechanism to identify the reactions that control the interaction between EHN and the fuel. As the result, EHN thermal decomposition is only relevant for very low temperatures. The chemistry of EHN-doped fuel is more sensitive to intermediate temperature reactions than that of straight fuel, especially at lower temperatures, due to the effect of EHN on the NTC behavior of the fuel. Finally, the chemistry of EHN-doped fuel is very sensitive to NO 2 -to-NO reactions, especially at high temperatures, because these reactions transform the NO 2 generated by EHN into NO, which is a very effective fuel reactivity enhancer.

2-ethylhexyl nitrate↗
DOE OSTI2020

Aluminum-doped calcium manganite particles for solar thermochemical energy storage: Reactor design, particle characterization, and heat and mass transfer modeling

A two-step cycle is discussed for solar thermochemical energy storage based on particulate aluminum-doped calcium manganite reduction/oxidation reactions for direct integration into Air Brayton cycles. The two steps encompass 1) the storage of concentrated solar irradiation within endothermic reduction of aluminum-doped calcium manganite and 2) the delivery of heat to an Air-Brayton cycle via exothermic re-oxidation of oxygen-deficient aluminum-doped calcium magnanite. A 5 kW th scale solar thermochemical reactor operating under vacuum was designed, modeled, and optimized to thermally reduce a continuous, gravity-driven flow of aluminum-doped calcium manganite particles. The granular flows were characterized in a tilt-flow rig, and particle image velocimetry was used to determine flow properties via frictional and velocity scaling relationships. Flow properties were integrated into a detailed heat and mass transfer model of the solar thermochemical reactor. A reactor design with 31° inclination angle, 230 g/min of particles, and 5.2 kW th radiative input from the high-flux solar simulator was discovered to produce an outlet flow temperature of 1158 K, with stoichiometric deviations of 0.076 and a storage efficiency of 0.628 while avoiding particle overheating and promoting longer particle residence times.

14 SOLAR ENERGY↗
DOE OSTI2020

Aluminum-doped U 3 Si 2 composite fuels with enhanced oxidation resistance

Al-doped U 3 Si 2 composite fuels with controlled microstructure were fabricated by spark plasma sintering that display greatly-improved oxidation resistance as compared with monolithic and Al-doped silicides prepared by standard powder metallurgy or arc melting. The effects of Al additives on the thermal-mechanical properties and oxidation resisance of the micron- and nano-sized U 3 Si 2 composites were investigated. Additionally, a minimal addition of 1.8 at% Al is effective to increase the onset oxidation temperature of as-fabricated U 3 Si 2 pellets to 580 °C, which can be further increased to 610 °C by thermal annealing. The Al-doped U 3 Si 2 composite fuels also display simultaneously higher hardness and fracture toughness than un-doped U3Si2. These results highlight an effective strategy by integrating minimal Al additives, microstructure control and post-thermal annealing to design advanced silicide fuels with excellent oxidation resistance, desired thermal-mechanical properties and maintained high fissile element density.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Rare Earth Nickelate Electrodes Containing Heavily Doped Ceria for Reversible Solid Oxide Fuel Cells

The electrochemical performance of composite rare-earth nickelate-rare-earth doped ceria oxygen electrodes, with a high level of rare-earth doping in ceria are reported. Additionally, the chemical stability of these compositions is reported at both the sintering (1240 ?C) and operating temperature (800 ?C). Specifically, a lanthanum nickelate La2NiO4+d (LNO) ?? 50 mol% lanthanum doped ceria (LDC50) oxygen electrode and a neodymium nickelate Nd2NiO4+d (NNO) ?? 50 mol% neodymium doped ceria (NDC50) oxygen electrode are tested in solid oxide fuel cell (SOFC) and solid oxide electrolysis cell (SOEC) modes and compared to a composite (La0.75Sr0.25)0.95MnO3±d (LSM)-8 mol% yttria stabilized zirconia (YSZ) electrode. The LNO–LDC50 oxygen electrode reaches a current density which is approximately three times that of the LSM-YSZ electrode in SOFC mode at 0.7 V and approximately two times the LSM-YSZ electrode at 1.2 V in SOEC mode. Similarly the NNONDC50 oxygen electrode reaches a current density which is approximately two times and approximately one and a half times that of LSM-YSZ at 0.7 V and 1.2 V respectively. Oxygen surface exchange results for LNO and NNO are also reported which show different oxygen exchange kinetics during oxidation versus reduction steps.

solid oxide electrolysis, solid oxide fuel cell (S↗
DOE OSTI2026

Tetrahedral Zn 2+ doping LiNi 0.6 Mn 0.2 Co 0.2 O 2 improves discharge capacity retention by altering surface Ni valence during cycling and preventing oxygen evolution

5 mol-% Zn 2+ was added to the co-precipitation synthesis of LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) to understand Zn's effect on the structural and electronic properties of NMC622. Zn is determined to successfully dope into the NMC crystal lattice as there is an increase in d-spacing along the [003], [104], and [110] directions and an increase in molar volume (100.75 cm 3 mol -1 for NMC622 and 101.00 cm 3 mol -1 for Zn-NMC). Through XPS, Zn is determined to dope on the tetrahedral 6c Wyckoff site in the NMC structure and TEM-EDS reveals that despite a slight ZnO impurity phase, 1.4 mol-% Zn successfully dopes into the crystal structure. Furthermore, cyclic voltammetry shows a suppressed anodic wave associated with oxygen evolution and EIS demonstrates that Zn-doped NMC decreases charge transfer resistance and increases Li diffusion by an order of magnitude. After the formation cycles, NMC has a higher 1 C accessible capacity, 141 mAh/g, over Zn-NMC (132 mAh/g), but after long term cycling Zn-NMC has a higher accessible capacity (117 mAh/g compared to 96 mAh/g for NMC) and increases discharge capacity retention by 18% leading to longer cycle life.

Electrochemistry↗
DOE OSTI2020

Crystal growth and scintillation properties of pure and Tl-doped Cs 3 Cu 2 I 5

Here, the Bridgman crystal growth and scintillation properties of both undoped and Tl-doped Cs 3 Cu 2 I 5 are presented. This material is very attractive for gamma and X-ray detection applications, with a density of 4.53 g/cm 3 and effective atomic number of 51.9. Undoped Cs 3 Cu 2 I 5 had a light yield of 41,500 photons/MeV, with an energy resolution of 4.4% at 662 keV. Thallium doping at 0.5 mol % resulted in a much-improved scintillation response, in which light yield increased to 98,200 photons/MeV and energy resolution reduced to 3.3% at 662 keV. The X-ray excited emission is centered at 442 nm for the undoped and 500 nm for the Tl-doped crystals. The undoped emission is broad, typical of excitonic emission, while thallium doping results in an even broader band with features of both the undoped and thallium defect-mediated emissions.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Electron Paramagnetic Resonance Characteristics and Crystal Structure of a Tutton Salt Analogue: Copper-Doped Cadmium Creatininium Sulfate

Electron paramagnetic resonance and crystallographic studies on copper-doped cadmium creatininium sulfate (CdCrnS) were undertaken to study the characteristics of a copper-hexahydrate complex in an organic analogue of Tutton's salt. X-ray diffraction experiments determined the crystal structure of CdCrnS at both 100 and 298 K. CdCrnS, like Tutton salt, crystallizes in the monoclinic space group P2 1 /n. The unit cell contains two cadmium hexahydrate complexes, four creatininium ions, four sulfates, and four additional solvation waters. Both crystallography and EPR find that the doped copper replaces the cadmium in the structure. Single-crystal EPR measurements at room temperature determined the g and copper hyperfine (A Cu ) tensors (principal values: g = 2.437, 2.134, and 2.080 and A Cu = -327, -84.8, and 7.33 MHz). EPR spectra of the powder at room temperature gave g = 2.448, 2.125, and 2.085 and A Cu = -315, -75.0, and 35.0 MHz and at 110 K gave g = 2.462, 2.116, and 2.077 and A Cu = -340, -30.0, and 35.0 MHz. The room-temperature tensors are close to the "rigid lattice limit" values found in copper-doped Tutton salts but with a higher gmin and weaker A Cu x coupling than average. A small but measurable temperature dependency of the tensors indicated the presence of a dynamic Jahn-Teller (JT) effect. In addition, the EPR line width changed dramatically with temperature, which is like that found in all copper-doped Tutton crystals. Utilizing the model of Silver-Getz for the g-value variation gave an estimate for the energy difference (δ 12 = 640 cm -1 ) between the ground and next highest JT configurations. An empirical correlation appears to exist between δ 12 and g min and A Cu x for the copper hexahydrates studied in similar crystals. Finally, this suggests a relationship between the amount of unpaired spins in the copper d-orbital x lobe and the gap between wells of the adiabatic potential surface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Ultrafast Charge Transfer Dynamics at the Origin of Photoconductivity in Doped Organic Solids

In spite of their growing importance for optoelectronic devices, the fundamental properties and photophysics of molecularly doped organic solids remain poorly understood. Such doping typically leads to a small fraction of free conductive charges, with most electronic carriers remaining Coulombically bound to the ionized dopant. Recently, we have reported photocurrent for devices containing vacuum-deposited TAPC (1,1-bis(4-bis(4- methylphenyl)aminophenyl)cyclohexane) doped with MoO 3 , showing that photoexcitation of charged TAPC molecules increases the concentration of free holes that contribute to conduction. Here, we elucidate the excited-state dynamics of such doped TAPC films to unravel the key mechanisms responsible for this effect. We demonstrate that excitation of different electronic transitions in charged and neutral TAPC molecules allows bound holes to overcome the Coulombic attraction to their MoO 3 counterions, resulting in an enhanced yield of long-lived free carriers. This is caused by ultrafast back-and-forth shuffling of charges and excitation energy between adjacent cations and neutral molecules, competing with relatively slow nonradiative decay from higher excited states of TAPC •+ . The light-induced generation of conductive carriers requires the coexistence of cationic and neutral TAPC, a favorable energy level alignment, and intermolecular interactions in the solid state.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Investigating Cu-Site Doped Cu–Sb–S Nanoparticles Using Photoelectron and Electron Paramagnetic Resonance Spectroscopy

Tetrahedrite (Cu 12 Sb 4 S 13 ) and famatinite (Cu 3 SbS 4 ) are good candidates for green energy applications because they possess promising thermoelectric and photovoltaic properties as well as contain earth-abundant and nontoxic constituents. Herein, X-ray photoelectron spectroscopy (XPS), ultraviolet photoelectron spectroscopy (UPS), and electron paramagnetic resonance spectroscopy (EPR) methods examined inherent electronic properties and interatomic magnetic interactions of Cu-site doped tetrahedrite and famatinite nanomaterials. An energy-efficient modified polyol method was utilized for the synthesis of tetrahedrite and famatinite nanoparticles doped on the Cu-site with Zn, Fe, Ni, Mn, and Co. This is the first parallel study of tetrahedrite and famatinite nanomaterials with XPS, UPS, and EPR methods alongside a systematic analysis of dopant-dependent effects on the electronic structure and magnetic interactions for each material. XPS showed that the Cu and Sb species in tetrahedrite and famatinite possess different oxidation states, while UPS characterization reveals larger dopant-dependent shifts in the work function for tetrahedrite nanoparticles (4.21 to 4.79 eV) than for famatinite nanoparticles (4.57 to 4.77 eV). Finally, all famatinite nanoparticles display an EPR signal, indicating trace amounts of paramagnetic Cu(II) present below the detection limit of XPS. For tetrahedrite, EPR signatures were observed only for the Zn-doped and Mn-doped nanoparticles, suggesting signal broadening from Cu–Cu spin exchange or spin–lattice relaxation. This study demonstrates the complementary nature of XPS and EPR techniques for studying the oxidation states of metals in solid-state nanomaterials. Comparing the electronic and magnetic properties of tetrahedrite and famatinite while studying the impact of dopant incorporation will guide future endeavors in designing sustainable, high-performance materials for renewable energy applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

The Effects of Iron and Manganese Doping on the Carbonation of Brucite [Mg(OH) 2 ]

Brucite [Mg(OH) 2 ] is a promising sorbent for carbon dioxide removal (CDR) due to its availability and low calcination temperatures. However, natural and synthetic brucites tend to contain metal impurities, such as iron or manganese, and how these impurities affect the interfacial chemical reactivity is uncertain. Here, in this study, the impact of low concentrations of iron and manganese impurities on the carbonation efficiency of Mg(OH) 2 was examined. Mg(OH) 2 with small amounts (1–5 mol %) of Fe and Mn was synthesized. The increasing substitution of Fe into Mg(OH) 2 was accompanied by the oxidation of Fe. The phase transformation sequence during the carbonation was found to be brucite [Mg(OH) 2 ] → amorphous magnesium carbonate (MgCO 3 ·nH 2 O) → nesquehonite (MgCO 3 ·3H 2 O), regardless of impurity concentration. Both the Fe- and Mn-doped Mg(OH) 2 samples were more reactive than endmember Mg(OH) 2 , possibly due to their higher surface areas and lower stabilities. During carbonation, 3 mol % Fe- and Mn-doped Mg(OH) 2 showed the highest reactivity. The variance in reactivity for Mn-doped Mg(OH) 2 was less than that of Fe-doped Mg(OH) 2 . These results suggest that natural or industrial waste Mg(OH) 2 with less than 5 mol % Fe and Mn impurities may be targeted as more effective CDR sorbents than endmember Mg(OH) 2 .

Carbon dioxide removal↗
DOE OSTI2022

Synthesis of Fluorine-Doped Lithium Argyrodite Solid Electrolytes for Solid-State Lithium Metal Batteries

Solid-state lithium metal batteries (SSLMBs) that utilize novel solid electrolytes (SEs) have garnered much attention because of their potential to yield safe and high-energy-density batteries. Sulfide-based argyrodite-class SEs are an attractive option because of their impressive ionic conductivity. Recent studies have shown that LiF at the interface between Li and SE enhances electrochemical stability. However, the synthesis of F-doped argyrodites has remained challenging because of the high temperatures used in the state-of-the-art solid-state synthesis methods. In this work, for the f irst time, we report F-doped Li 5+y PS 5 F y argyrodites with a tunable doping content and dual dopants (F-/Cl- and F-/Br-) that were synthesized through a solvent-based approach. Among all compositions, Li 6 PS 5 F 0.5 C l0.5 exhibits the highest Li-ion conductivity of 3.5 x 10 -4 S cm -1 at room temperature (RT). Furthermore, Li symmetric cells using Li 6 PS 5 F 0.5 Cl 0.5 show the best cycling performance among the tested cells. X-ray photoelectron spectroscopy and ab initio molecular dynamics simulations revealed that the enhanced interfacial stability of Li 6 PS 5 F 0.5 C l0.5 SE against Li metal can be attributed to the formation of a stable solid electrolyte interphase (SEI)-containing conductive species (Li 3 P), alongside LiCl and LiF. These findings open new opportunities to develop high-performance SSLMBs using a novel class of F-doped argyrodite electrolytes.

25 ENERGY STORAGE↗
DOE OSTI2020

P-Type Electrochemical Doping Can Occur by Cation Expulsion in a High Performing Polymer for Organic Electrochemical Transistors

We investigate the mechanism of ion-dependent charge compensation during electrochemical oxidation (doping) of the model mixed ionic/electronic transporting polythiophene derivative poly(3-{[2-(2-methoxyethoxy)ethoxy]methyl}thiophene-2,5-diyl) (P3MEEMT). Using a combination of electrochemical quartz microbalance gravimetry and glow discharge optical emission spectroscopy, we show that charge compensation during polymer redox processes proceeds via a cation-dependent mechanism. For p-type polymer oxidation in certain electrolytes, charge compensation is achieved by both eventual injection of anions into the film, as well as initial expulsion of cations from the film. We compare doping mechanisms for a variety of electrolyte salts including potassium chloride, tetrabutylammonium chloride, potassium hexafluorophosphate (KPF6), and tetrabutylammonium hexafluorophosphate. For the electrolyte KPF6, both the cations and anions coexist in the water-swelled polymer even prior to application of electrical bias. Our data indicate that electrochemical doping (hole injection into the polymer and ionic charge compensation) proceeds via the following mechanism: (1) hydration of the neutral film by electrolyte (water, cations, anions), (2) cation (K+) expulsion from the film upon initial application of an oxidative bias, and (3) anion injection into the film at higher oxidation/doping levels (>~2 × 1020/cm3). Understanding the mechanism of charge compensation during the doping process should allow for the design of improved mixed ionic/electronic conductors for use in applications ranging from organic supercapacitors and redox flow batteries to bioelectronic sensors, thermoelectrics, and devices for neuromorphic computing.

Flagg, Lucas Q.↗
DOE OSTI2023

Modulation-doping a correlated electron insulator

Abstract Correlated electron materials (CEMs) host a rich variety of condensed matter phases. Vanadium dioxide (VO 2 ) is a prototypical CEM with a temperature-dependent metal-to-insulator (MIT) transition with a concomitant crystal symmetry change. External control of MIT in VO 2 —especially without inducing structural changes—has been a long-standing challenge. In this work, we design and synthesize modulation-doped VO 2 -based thin film heterostructures that closely emulate a textbook example of filling control in a correlated electron insulator. Using a combination of charge transport, hard X-ray photoelectron spectroscopy, and structural characterization, we show that the insulating state can be doped to achieve carrier densities greater than 5 × 10 21 cm −3 without inducing any measurable structural changes. We find that the MIT temperature (T MIT ) continuously decreases with increasing carrier concentration. Remarkably, the insulating state is robust even at doping concentrations as high as ~0.2 e − /vanadium. Finally, our work reveals modulation-doping as a viable method for electronic control of phase transitions in correlated electron oxides with the potential for use in future devices based on electric-field controlled phase transitions.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Low resistance p-type contacts to monolayer WSe2 through chlorinated solvent doping

Tungsten diselenide (WSe 2 ) is a promising p-type semiconductor limited by high contact resistance (R C ) and the lack of a reliable doping strategy. Here, we demonstrate that exposing WSe 2 to chloroform provides simple and stable p-type doping. In monolayer WSe 2 transistors with Pd contacts, chloroform increases the maximum hole current by over 100× (>200 µA/µm), reduces R C to ~ 2.5 kΩ·μm, and retains an on/off ratio of 10 10 at room temperature. These improvements persist for over 8 months, survive a 150 °C thermal anneal, and remain effective down to 10 K, enabling a cryogenic R C of ~ 1 kΩ·μm. Density functional theory indicates that chloroform strongly physisorbs to WSe 2 , inducing hole doping with minimal impact on the electronic states between the valence band and conduction band edges. Auger electron spectroscopy and atomic force microscopy suggest that chloroform intercalates at the WSe 2 interface with the gate oxide, contributing to doping stability and mitigating interfacial dielectric disorder, though further studies are needed to conclusively confirm this mechanism. This robust, scalable approach enables high-yield WSe 2 transistors with good p-type performance.

42 ENGINEERING↗
DOE OSTI2025

Pseudo-equilibrium theory for extrinsic doping control of the topological semimetal Cd 3 As 2

The standard approach for predicting defect equilibria from first principles assumes that the solid-state system is initially in a thermodynamic equilibrium with the external atomic reservoirs. This “growth step” is then often followed by a temperature quench in a “pseudo-equilibrium” in which some or all defect concentrations are frozen in until only the Fermi level E F remains to be equilibrated. However, this protocol does not account for the possibility of site exchanges which can create important defect redistributions as long as short-range defect migration is kinetically permissible. To model this redistribution, we developed an approach to solve for the non-equilibrium chemical potentials as a function of temperature while maintaining the overall defect stoichiometry. We then apply this approach to the Dirac semimetal Cd 3 As 2 to model extrinsic doping with group 1/11 and 14 elements. Undoped Cd 3 As 2 exhibits an undesirable mismatch between E F and the Dirac point. This unintentional electron doping originates from intrinsic defects and is difficult to overcome through adjustment of synthesis conditions alone. Employing our pseudo-equilibrium modeling, we identify extrinsic doping strategies for realizing doping-balanced Cd 3 As 2 at the relatively low temperatures accessible in thin-film growth of this material.

36 MATERIALS SCIENCE↗