Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Computational Margin”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS2006

The X-43 Fin Actuation System Problem - Reliability in Shades of Gray

Following the loss of the first X-43 during launch, the mishap investigation board indicated the Fin Actuator System (FAS) needed to have a larger torque margin. To supply this added torque, a second actuator was added. The consequences of what seemed to be a simple modification would trouble the X-43 program. Because of the second actuator, a new computer board was required. This proved to be subject to electronic noise. This resulted in the actuator latch up in ground tests of the FAS for the second launch. Such a latch up would cause the Pegasus booster to fail, as the FAS was a single string system. The problem was corrected and the second flight was successful. The same modifications were added to the FAS for flight three. When the FAS underwent ground tests, it also latched up. The failure indicated that each computer board had a different tolerance to electronic noise. The problem with the FAS was corrected. Subsequently, another failure occurred, raising questions about the design, and the probability of failure for the X-43 Mach 10 flight. This was not simply a technical issue, but illuminated the difficulties facing both managers and engineers in assessing risk, design requirements, and probabilities in cutting edge aerospace projects.

Peebles, Curtis↗
NASA NTRS2005

Space Shuttle Underside Astronaut Communications Performance Evaluation

The Space Shuttle Ultra High Frequency (UHF) communications system is planned to provide Radio Frequency (RF) coverage for astronauts working underside of the Space Shuttle Orbiter (SSO) for thermal tile inspection and repairing. This study is to assess the Space Shuttle UHF communication performance for astronauts in the shadow region without line-of-sight (LOS) to the Space Shuttle and Space Station UHF antennas. To insure the RF coverage performance at anticipated astronaut worksites, the link margin between the UHF antennas and Extravehicular Activity (EVA) Astronauts with significant vehicle structure blockage was analyzed. A series of near-field measurements were performed using the NASA/JSC Anechoic Chamber Antenna test facilities. Computational investigations were also performed using the electromagnetic modeling techniques. The computer simulation tool based on the Geometrical Theory of Diffraction (GTD) was used to compute the signal strengths. The signal strength was obtained by computing the reflected and diffracted fields along the propagation paths between the transmitting and receiving antennas. Based on the results obtained in this study, RF coverage for UHF communication links was determined for the anticipated astronaut worksite in the shadow region underneath the Space Shuttle.

Hwu, Shian U.↗
NASA NTRS2019

Technology Development and Infusion by NASA's Entry Systems Modeling Project

This presentation describes recent development of modeling and simulation technologies by NASA's Entry Systems Modeling Project and their infusion into the Agency's exploration missions. Technology development is organized and prioritized using a system-level perspective, resulting in four broad technical areas of investment: (1) Thermal protection material modeling, (2) Shock layer kinetics and radiation, (3) Computational and experimental aerosciences, and (4) Guidance, navigation, and control. The presentation will illustrate how applied research can meaningfully impact flight programs by highlighting a few recent contributions: Orion and Mars 2020 radiative heating margin policy; Study of radiative heating at Titan; Aerothermal-mechanical erosion due to dust at Mars; Modeling the PICA-NuSil system; and contributions to modeling of parachutes for entry systems.

Barnhardt, Michael D.↗
NASA NTRSDate not supplied

Magnetohydrodynamics (MHD) Aerocapture System for Enabling Faster-Larger Planetary Science & Human Exploration Missions

Since our completing the NIAC Phase I NIAC on this Advanced Aerocapture System, NASA Langley Research Center has funded or supported a number of studies and code enhancements through its Center Innovation Fund (CIF) and NASA’s NSTGRO and Internship Programs to mature the analysis capabilities and quantify the merits of the MHD Aerocapture System technology. These efforts have resulted in a plug and play analysis capability for assessing MHD aerocapture system performance for arrival at many planetary bodies of interest. Our efforts have especially focused on the potential mass savings for improving the capacity for science observations at Neptune and Triton. A re-cent Forbes article published “‘Orbital mechanics is probably going to decide for us whether we go to Uranus or Neptune because we need to flyby Jupiter,’ said Kunio Sayanagi at Hampton University, Virginia, who also worked on the Neptune Odyssey proposal…. Exactly when a mission can be sent to Uranus, or Neptune, depends on the relative position of Jupiter, which can help give a spacecraft a gravitational slingshot. That drastically shortens the cruise phase.” [1] Since shortening the cruise phase is important for these science missions, any mass savings enabled by the MHD Aerocapture System could be reallocated to increasing Thermal Protection System mass to allow faster arrival speeds and/or for onboarding additional payloads such as science instruments, batteries, or propellant for conducting more science for longer durations in the desired orbits. The analysis steps and codes for conducting trades and sizing vehicles for aerocapture are as follows: Step 1 is to conduct aeroheating analysis using LAURA of the selected entry vehicle shape to identify locations on the forebody where ionization and flow velocity are sufficient for producing Lo-rentz forces. LAURA is a multiblock structured grid finite-volume CFD solver developed at the NASA Langley Research Center. [2] LAURA has been used for aerothermal analysis support of the entry, de-scent and landing (EDL) phase of interplanetary missions over the last three decades [3-7]. Step 2 is to port the LAURA results into CFDWARP to calcu-late electrical and thermal conductivities of ionized flow for sizing MHD patch system and calculating Lorentz forces needed for controls analysis. CFDWARP is a CFD code that uses advanced nu-merical methods that enable the simulation of the full coupling between the aerodynamics, the magne-tohydrodynamics, and the non-neutral plasma sheaths. CFDWARP has the unique capability to simulate efficiently the non-neutral sheaths (near the electrodes) in coupled form with the quasi-neutral bulk MHD flow [8-11]. Step 3 is to link re-sults from LAURA and CFDWARP into POST2 for calculating entry trajectories and comparing MHD control results with other aerodynamic control strategies. The Program to Optimize Simulated Tra-jectories II (POST2) is a generalized point mass, discrete parameter targeting and optimization pro-gram. POST2 provides the capability to target and optimize point mass trajectories for multiple pow-ered or un-powered vehicles near an arbitrary rotat-ing, oblate planet [12]. Step 4: TPS sizing was per-formed using the Fully Implicit Ablation and Ther-mal-response code (FIAT) tool which computes the transient one-dimensional thermal response and surface thermochemistry of a multilayer stackup of thermal protection, bonding, and structural materi-als subject to aeroheating on one surface [13]. The sizing and margining methodology used was based on the approach documented by Mahzari and Milos [14] for the dual-layered heatshield for extreme entry environment technology (DL-HEEET) TPS concept. TPS analysis utilizes trajectory information from POST2. Using this step-wise plug and play MHD Aerocapture performance assessment process, our analysis targets a Neptune aerocapture trajectory that will place the spacecraft in an observation orbit for Triton. [15]. Magnetohydrodynamic (MHD) control of a 4.5-meter diameter MSL-style capsule resulted in TPS mass savings of nearly 2000 kg when using an MHD system mass of under 200 kg. The flight path for a vehicle using the MHD control strategy has a much lower heat rate and heat load compared to the conventional aerodynamic aerocapture strategies known as bank angle con-trolled (BAC) and direct force controlled (DFC). Both BAC and DFC have heat rates significantly greater than 1500 W/cm2 typically used as an upper limit for PICA. Thus, DL-HEEET TPS concept was required for the BAC and DFC control strategies. However, considering the more benign environ-ments for the MHD case, additional TPS concepts with improved mass efficiency were also assessed. PICA was considered for the MHD controlled strat-egy since the maximum heat rate was well within the limits (<1500 W/cm2) of PICA. TPS sizing re-sulted in a significant mass reduction. The PICA layer for this sizing case was about 7.8 cm. As a point of reference, the Mars 2020 mission, which used this same PICA concept, had a PICA thickness of 3.18 cm [16]. The trajectories used for the TPS sizing originat-ed from the POST2 simulations. The current, I, to an electromagnet configuration can be manipulated to allow for active control of the vehicle. Manipula-tion of the current, I, changes the magnetic field, B, which affects the Lorentz force and therefore the MHD drag force on the vehicle. Our analysis in-cluded both open-loop and close-loop control. Closed-loop control will enable improved overall performance when taking into account mission level uncertainties, such as interplanetary delivery errors and atmospheric modeling uncertainties. The open-loop and closed-loop MHD control cases do not dip as deep into the atmosphere as the aerodynamic cases. Three types of aerodynamic-only approach-es are investigated: bank angle modulation (BAM), director force control (DFC), and Drag Modulated. BAM and DFC make use of vehicle aerodynamic angles to steer the vehicle. Thus, changing the aer-odynamic forces acting on the vehicle for control, aerodynamic drag modulated case requires a vary-ing drag area to modulate the drag force. The MHD drag modulated case modulates MHD generated drag force that adds to the aerodynamic drag. This higher atmospheric activation of drag forces by the MHD patch results in significantly less heat flux on the vehicle. The MHD technology will enable shorter cruise times and deceleration of larger payloads for increasing the capacity for science at the Ice Giants or for returning astronauts to Earth from cislunar space or from Mars. The purpose of this presentation is to provide more details about this work and to highlight plans for further research and development including a flight demonstration.

R. W. Moses↗
DOE OSTI2020

Issue Summary of INL Phase IV Transient Results for IAEA CRP on HTGR UAM Benchmark

This report details the Parallel and Highly Innovative Simulation for Idaho National Laboratory (INL) Code System (PHISICS)/Reactor Excursions and Leak Analysis Program (RELAP5)-3D results obtained for the transient core exercises defined for Phase IV of the International Atomic Energy Agency (IAEA) Coordinated Research Project (CRP) on high-temperature gas cooled reactor (HTGR) uncertainty analysis in modeling (UAM). The Phase III models and results are linked to the earlier Standardized Computer Analyses for Licensing Evaluation (SCALE)/Sampler/New ESC-based Weighting Transport (NEWT) data generated for the lattice physics (lattice) stage Phase I of the CRP. The focus of this report is the Uncertainty/Sensitivity Assessment (U/SA) of the prismatic modular high-temperature gas cooled reactor (MHTGR)-350 design, and specifically for Exercises IV-1 and IV-2 of the benchmark: the Control Rod Withdrawal (CRW) and Pressurised Loss of Cooling (PLOFC) events. The statistical U/SA methodology is implemented and demonstrated using the RAVEN code, based on perturbed cross-section libraries obtained from the SCALE/Sampler sequence. Uncertainties in nuclear data (cross-sections and the average number of neutrons produced per fission, 235U[¯v ]) lead to standard deviations (uncertainties of one s) of approximately 0.5% in the core eigenvalues of the MHTGR-350 and core models. For the coupled neutronics/thermal fluid model, local power density uncertainties up to 3.6% were observed in the colder regions of the core, while the local maximum fuel temperature uncertainties reached 1.5% for the models that included thermal fluid uncertainties. The addition of thermal fluid uncertainties dominated the impacts of nuclear data uncertainties in all cases. The main contributors to uncertainties in the power density and fuel temperatures during the transients were uncertainties in the reactor operating conditions (total power, inlet mass flow rate and inlet gas temperature). Variations in the bypass flows did not have significant impact on any of the output variables. For the nuclear data uncertainties it was found that the 235U(¯v ) / 235U(¯v ) covariance produced the largest sensitivities in terms of its impact on the eigenvalue and peak reactor power. It was also observed that the impact of any nuclear data uncertainties on the maximum fuel temperature was much less significant that the impact on eigenvalue and power. Another important finding was that although the use of eight or more energy groups is recommended for best-estimate HTGR simulation, two-group models produced acceptable uncertainty and sensitivity results for most FOMs. Since the statistical U/SA methodology is computationally expensive, and most transient solver requirements will scale directly with the number of energy groups, two energy groups could be used by HTGR developers during the early stages of design when larger uncertainty margins can be tolerated.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

TRUST Nonlinear Dynamics (ND) Report: FY22

The objective of the Delivery Environments (DE) Testbeds to Reduce Uncertainty in Simulations and Tests (TRUST) work package, is to quantify and help increase confidence in specific areas of computational and experimental capabilities that are applicable to current and future delivery environments. More complete quantification of confidence in experimental and computational capabilities and the sufficient increase of confidence in those capabilities is critical to improving weapons engineering design, qualification, and assessment efforts that are relevant to the current and future stockpile. This work will use and provide feedback on analysis tools and experimental results databases for efficient and responsive engineering which are currently under development: engineering common model framework (ECMF), engineering quantification of margins and uncertainties (EQMU), and the test information management system (TIMS). Additionally, this work is being used to test a newly available framework in W-13, Weapons Analysis for Verified Engineering Simulation (WAVES).

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
NASA NTRS1994

Computer simulation of the effect of dDAVP with saline loading on fluid balance after 24-hour head-down tilt

Fluid loading (FL) before Shuttle reentry is a countermeasure currently in use by NASA to improve the orthostatic tolerance of astronauts during reentry and postflight. The fluid load consists of water and salt tablets equivalent to 32 oz (946 ml) of isotonic saline. However, the effectiveness of this countermeasure has been observed to decrease with the duration of spaceflight. The countermeasure's effectiveness may be improved by enhancing fluid retention using analogs of vasopressin such as lypressin (LVP) and desmopressin (dDAVP). In a computer simulation study reported previously, we attempted to assess the improvement in fluid retention obtained by the use of LVP administered before FL. The present study is concerned with the use of dDAVP. In a recent 24-hour, 6 degree head-down tilt (HDT) study involving seven men, dDAVP was found to improve orthostatic tolerance as assessed by both lower body negative pressure (LBNP) and stand tests. The treatment restored Luft's cumulative stress index (cumulative product of magnitude and duration of LBNP) to nearly pre-bedrest level. The heart rate was lower and stroke volume was marginally higher at the same LBNP levels with administration of dDAVP compared to placebo. Lower heart rates were also observed with dDAVP during stand test, despite the lower level of cardiovascular stress. These improvements were seen with only a small but significant increase in plasma volume of approximately 3 percent. This paper presents a computer simulation analysis of some of the results of this HDT study.

NASA Discipline Cardiopulmonary↗
DOE OSTI2025

Scaled-up fabrication of durable and porous adsorbent-coated minichannels on aluminum for CO 2 separation

A method was developed to fabricate zeolite 13X adsorbent-coated minichannels on aluminum for CO₂ adsorption applications in this study. It emphasizes the innovative use of aluminum as a substrate, which offers airtight assembly, paving the way for highly efficient adsorption systems. An optimized coating process was developed using a slurry of Zeolite 13X, yeast, sugar, and xanthan gum, resulting in durable and highly porous layers that enhance CO₂ capture performance. A PETG peeler was designed to remove the top layer of the yeast-engineered adsorbent coatings, revealing a super porous and foamy structure. The teeth of the peeler were designed and fabricated for high repeatability and rapid prototyping. Breakthrough experiments were conducted on the scaled-up adsorbent bed using gas mixtures of 80% CO₂, 20% N₂, and 20% CO₂, 80% N₂ to represent different industrial scenarios. The performance of the bed was evaluated at flow rates of 160 and 190 cm³ min -1 using a Raman Laser Gas Analyzer (RLGA), demonstrating stable adsorption without degradation across multiple cycles. Computational modeling of integral transport phenomena under the chosen experimental conditions was pursued using gPROMS ProcessBuilder™, and the modeling results were compared with those from the tests for adsorption time, which resulted in an error margin of 2% to 9% for the breakthrough time, confirming the easy reproducibility of the design through modeling. This research advances CO₂ capture technologies by providing an effective and scalable solution for producing aluminum-based adsorbent coated beds, supporting industrial carbon capture efforts.

CO2 capture↗
DOE OSTI2024

Ion-temperature- and density-gradient-driven instabilities and turbulence in Wendelstein 7-X close to the stability threshold

Electrostatic gyrokinetic instabilities and turbulence in the Wendelstein 7-X stellarator are studied. Particular attention is paid to the ion-temperature-gradient (ITG) instability and its character close to marginal stability [Floquet-type turbulence (Zocco et al., Phys. Rev. E, vol. 106, 2022, p. L013202) with no electron temperature gradient]. The flux tube version of the δƒ code stella (Barnes et al., J. Comput. Phys., vol. 391, 2019, pp. 365–380) is used to run linear and nonlinear gyrokinetic simulations with kinetic electrons. The nature of the dominant instability depends on the wavelength perpendicular to the magnetic field, and the results are conveniently displayed in stability diagrams that take this dependence into account. This approach highlights the presence of universal instabilities, which are less unstable but have longer wavelengths than other modes. A quasi-linear estimate of the heat flux suggests they are relevant for transport. Close to the stability threshold, the linear eigenmodes and turbulence form highly extended structures along the computational domain if the magnetic shear is small. Numerical experiments and diagnostics are undertaken to assess the resulting radial localisation of the turbulence, which affects the interaction of the latter with zonal flows. Increasing the amplitude of the magnetic shear (e.g.through current drive) has a stabilising effect on the turbulence and, thus, reduces the nonlinear energy transport.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Multiscale Modeling of Plutonium Radiation Chemistry in Nitric Acid Solutions. 1. Cobalt-60 Gamma Irradiation of Pu(IV)

We report careful manipulation of the plutonium oxidation states is essential in the study and utilization of its rich redox chemistry. To achieve this level of control, a comprehensive mechanistic understanding of radiation-induced plutonium redox chemistry is critical due to the unavoidable exposure of plutonium to ionizing radiation fields, both inherent and from in-process applications. To this end, we have developed an experimentally evaluated multiscale computer model for the prediction of gamma radiation-induced Pu(IV) redox chemistry in concentrated nitric acid solutions (1.0, 3.0, and 6.0 M). Under these acidic, aqueous solution conditions, cobalt-60 gamma irradiation afforded marginal net conversion of Pu(IV) to Pu(VI), the extent of which was dependent on the concentration of HNO 3 and absorbed gamma dose. Multiscale calculations, which are in excellent agreement with experimental data, indicate that this observation is due to a combination of inherent plutonium disproportionation reactions and several radiation-induced processes, including redox cycling between Pu(IV) and Pu(III), as achieved by the reduction of Pu(IV) by nitrous acid and hydrogen peroxide, the oxidation of Pu(III) by nitrate and hydroxyl radicals, and the sequential oxidation of Pu(IV) to Pu(V) and Pu(VI) by the remaining available yield of nitrate radicals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Constrained variational optimization of counting-time allocation in sequential scattering measurements: Application to Bonse–Hart USANS

Sequential scattering measurements are often performed under a fixed experimental-time budget, even though the expected count rate varies strongly across the measured coordinate. When the dwell time at each measurement position can be controlled independently, this variation creates a general resource-allocation problem: how should the available time be distributed to minimize the uncertainty of the reconstructed profile? We formulate this problem as a constrained variational optimization for measurements governed by Poisson counting statistics. When each measurement is treated independently, minimizing the averaged squared relative uncertainty yields an inverse-square-root intensity allocation. The formulation is then generalized to include correlations between neighboring measurements and an instrumental resolution operator, leading to an allocation criterion that equalizes the marginal reduction in posterior uncertainty per unit measurement time. Bonse–Hart ultra-small-angle neutron scattering (USANS), in which reciprocal space is sampled sequentially through analyzer-angle stepping, provides an experimentally grounded application. Computational benchmarking shows that the optimized allocation outperforms uniform-time and constant-relative-error strategies, while application to an experimentally measured graphite USANS profile from the Spallation Neutron Source, using Poisson resampling under alternative schedules, demonstrates how counting time should be redistributed toward weak-intensity regions under an identical total duration. The resulting framework applies to sequential scattering and related scanning measurements whenever local dwell times are adjustable and directly determine the measurement uncertainties, and when the relevant correlation and instrumental-response models are available.

Tung, Chi-Huan [ORNL] (ORCID:0000000221972074)↗
DOE OSTI2022

Structure-Informed Graph Learning of Networked Dependencies for Online Prediction of Power System Transient Dynamics

Online transient analysis plays an increasingly important role in dynamic power grids as the renewable generation continues growing. Traditional numerical methods for transient analysis not only are computationally intensive but also require precise contingency information as input, and therefore, are not suitable for online applications. Existing online transient assessment studies focus on the determination of post-contingency system stability or stability margin. Here, this paper develops a novel graph-learning framework, Deep-learning Neural Representation or DNR, for online prediction, of the time-series trajectories of the system states using initial system responses that can be measured by phasor measurement units (PMUs). The proposed DNR framework consists of two sequential modules: a Network Constructor that captures network dependencies among generators, and a Dynamics Predictor that predicts the system trajectories. The key to improved prediction performance is the introduction of the spatio-temporal message-passing operations into graph neural networks with structural knowledge. Its effectiveness and scalability are validated through comparative studies, demonstrating the prediction performance under different contingency scenarios for systems of different sizes. This framework provides a solution to online predicting post-fault system dynamics based on real-time PMU measurements. Additionally, it can also be applied to facilitate the offline transient simulation without simulating the entire trajectories.

24 POWER TRANSMISSION AND DISTRIBUTION↗
NASA NTRS1972

Stability evaluation of a rocket engine for gaseous oxygen difluoride (OF2) and gaseous diborane (B2H6) propellants

Results of an experimental evaluation of the dynamic stability of a candidate combustor for the space storable propellants gaseous OF2/B2H6 show that the combustor is unstable without supplementary damping. A computer analysis indicated that the uninhibited engine could be unstable. The experiments, conducted with O2/C2H4 substitute propellants and with 70-30 FLOX/B2H6 (OF2 simulated with FLOX), show that the uninhibited combustor has a low stability margin to starting transient perturbations, but that is relatively insensitive to bomb disturbances. Damping cavities are shown to provide stability.

Clayton, R. M.↗
NASA NTRS1985

Experimental verification and practical application of torquewhirl theory of rotordynamic instability

A theory developed by Vance in 1978 to explain the destabilizing effect of torque on a whirling rotor was experimentally verified. The measurements made on a specially designed test apparatus are described. New computer models were also developed to investigate the effect of torque on rotordynamic stability of multidisk flexible rotor bearing systems. The effect of torque was found to be most pronounced when the system is already marginally stable from other influences. The modifications required to include torque in a typical shaft transfer matrix are described, and results are shown which identify the type of rotor design most sensitive to load torque.

Vance, J. M.↗
NASA NTRS1987

Study of instability and active control of boundary layers using Navier-Stokes equations

Spatial stability of a three-dimensional growing boundary layer is studied using Navier-Stokes equations. The finite difference method used is an explicit, predictor-corrector type which is fourth-order accurate in space and second-order in time. Active control of two-dimensional disturbances is simulated by localized surface heating. The computations show features of the flow relevant to early stages of transition such as lifting of vorticity away from the wall and localized regions of intense shear. Active control with single heating strip is only marginally effective, but may be improved by multiple strips.

Parikh, Paresh↗
NASA NTRS1988

A new momentum management controller for the Space Station

A new approach to CMG (control moment gyro) momentum management and attitude control of the Space Station is developed. The control algorithm utilizes both the gravity-gradient and gyroscopic torques to seek torque equilibrium attitude in the presence of secular and cyclic disturbances. Depending upon mission requirements, either pitch attitude or pitch-axis CMG momentum can be held constant; yaw attitude and roll-axis CMG momentum can be held constant, while roll attitude and yaw-axis CMG momentum cannot be held constant. As a result, the overall attitude and CMG momentum oscillations caused by cyclic aero-dynamic disturbances are minimized. A state feedback controller with minimal computer storage requirement for gain scheduling is also developed. The overall closed-loop system is stable for + or - 30 percent inertia matrix variations and has more than + or - 10 dB and 45 deg stability margins in each loop.

Wie, B.↗
NASA NTRS1988

A new momentum management controller for the space station

A new approach to CMG (control moment gyro) momentum management and attitude control of the Space Station is developed. The control algorithm utilizes both the gravity-gradient and gyroscopic torques to seek torque equilibrium attitude in the presence of secular and cyclic disturbances. Depending upon mission requirements, either pitch attitude or pitch-axis CMG momentum can be held constant: yaw attitude and roll-axis CMG momentum can be held constant, while roll attitude and yaw-axis CMG momentum cannot be held constant. As a result, the overall attitude and CMG momentum oscillations caused by cyclic aero-dynamic disturbances are minimized. A state feedback controller with minimal computer storage requirement for gain scheduling is also developed. The overall closed-loop system is stable for + or - 30 percent inertia matrix variations and has more than + or - 10 dB and 45 deg stability margins in each loop.

Wie, B.↗
NASA NTRS1993

Photometric investigation of a very short period W UMa-type binary - Does CE Leonis have a large superluminous area?

A complete photometric analysis of BVRI Johnson-Cousins photometry of the high northern latitude galactic variable, CE Leo is presented. These observations were taken at Kitt Peak National Observatory on May 31, 1989-June 7, 1989. Three new precise epochs of minimum light were determined and a linear and a quadratic ephemeris were computed from these and previous data covering 28 years of observation. The light curves reveal that the system undergoes a brief 20 min totality in the primary eclipse, indicating that CE Leo is a W UMa W-type binary. A systemic velocity of about -40 km/s was determined. Standard magnitudes were found and a simultaneous solution of the B, V, R, I light curves was computed using the new Wilson-Devinney synthetic light curve code which has the capability of automatically adjusting star spots. The solution indicates that the system consists of two early K-type dwarfs in marginal contact with a fill-out factor less than 3 percent. Evidence for the presence of a large (45 deg radius) superluminous area on the cooler component is given.

Samec, Ronald G.↗