Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Combustion simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS2008

Thermal Barrier and Protective Coatings to Improve the Durability of a Combustor Under a Pulse Detonation Engine Environment

Pulse detonation engine (PDE) concepts are receiving increasing attention for future aeronautic propulsion applications, due to their potential thermodynamic cycle efficiency and higher thrust to density ratio that lead to the decrease in fuel consumption. But the resulting high gas temperature and pressure fluctuation distributions at high frequency generated with every detonation are viewed to be detrimental to the combustor liner material. Experimental studies on a typical metal combustion material exposed to a laser simulated pulse heating showed extensive surface cracking. Coating of the combustor materials with low thermal conductivity ceramics is shown to protect the metal substrate, reduce the thermal stresses, and hence increase the durability of the PDE combustor liner material. Furthermore, the temperature fluctuation and depth of penetration is observed to decrease with increasing the detonation frequency. A crack propagation rate in the coating is deduced by monitoring the variation of the coating apparent thermal conductivity with time that can be utilized as a health monitoring technique for the coating system under a rapid fluctuating heat flux.

Ghosn, Louis J.↗
NASA NTRS2010

Heat Flux and Wall Temperature Estimates for the NASA Langley HIFiRE Direct Connect Rig

An objective of the Hypersonic International Flight Research Experimentation (HIFiRE) Program Flight 2 is to provide validation data for high enthalpy scramjet prediction tools through a single flight test and accompanying ground tests of the HIFiRE Direct Connect Rig (HDCR) tested in the NASA LaRC Arc Heated Scramjet Test Facility (AHSTF). The HDCR is a full-scale, copper heat sink structure designed to simulate the isolator entrance conditions and isolator, pilot, and combustor section of the HIFiRE flight test experiment flowpath and is fully instrumented to assess combustion performance over a range of operating conditions simulating flight from Mach 5.5 to 8.5 and for various fueling schemes. As part of the instrumentation package, temperature and heat flux sensors were provided along the flowpath surface and also imbedded in the structure. The purpose of this paper is to demonstrate that the surface heat flux and wall temperature of the Zirconia coated copper wall can be obtained with a water-cooled heat flux gage and a sub-surface temperature measurement. An algorithm was developed which used these two measurements to reconstruct the surface conditions along the flowpath. Determinations of the surface conditions of the Zirconia coating were conducted for a variety of conditions.

Cuda, Vincent, Jr.↗
NASA NTRS2004

A Preliminary Study on the Toxic Combustion Products Testing of Polymers Used in High-Pressure Oxygen Systems

One likely cause of polymer ignition in a high-pressure oxygen system is adiabatic-compression heating of polymers caused by pneumatic impact. Oxidative _ pyrolysis or combustion of polymers in a high-pressure oxygen system could generate toxic gases. This paper reports the preliminary results of toxic combustion product testing of selected polymers in a pneumatic-impact test system. Five polymers commonly used in high-pressure oxygen systems, Nylon 6/6, polychlorotrifluoroethylene (CTFE), polytetrafluoroethylene (PTFE), fluoroelastomer (Viton(TradeMark) A), and nitrile rubber (Buna N), were tested in a pneumatic-impact test system at 2500- or 3500-psia oxygen pressure. The polymers were ignited and burned, then combustion products were collected in a stainless-steel sample bottle and analyzed by GC/MS/IRD, GC/FID, and GC/Methanizer/FID. The results of adiabatic-compression tests show that combustion of hydrocarbon polymers, nitrogen-containing polymers, and halogenated polymers in high-pressure oxygen systems are relatively complete. Toxicity of the combustion product gas is presumably much lower than the combustion product gas generated from ambient-pressure oxygen (or air) environments. The NASA-Lewis equilibrium code was used to determine the composition of combustion product gas generated from a simulated, adiabatic-compression test of nine polymers. The results are presented and discussed.

Hshieh, Fu-Yu↗
NASA NTRS2018

Microgravity Experiments of Solid Waste Conversion into Useful Commodities

This Summer I participated in two projects at Kennedy Space Center in Cape Canaveral, Florida. The projects focus on the NASA's Deep Space Gateway applications for future Mars travel. All of these projects use recycling technology to use resources found on Earth and on other planets for fuel and other environmental applications. The first project I took the lead on is “Plasma Arc Gasification.” Plasma is a high temperature and very efficient way to process waste to create usable byproducts. The plasma chamber in temperature is comparable to that of the sun and this energy will help create an environment in which the waste can be recycled properly for not only plant support, but also for possible fuel application as well. I preformed the tests in a quartz tube, which is used to hold the waste (cotton, plastics, nylon, paper and a human waste simulant) and the waste is then combusted using O2 (present in air) into gases such as H2, H2O, CH4 and CO2. I determined which gases are present using a Fourier-transform infrared spectroscopy (FTIR) machine, which analyzes the peaks of the gases using liquid nitrogen. Problems arose in the beginning from the reactor emitting electromagnetic waves (EMI) that interfered with the technology of the experiment, specifically the thermocouples. This was solved through multiple tests with the positioning of the thermocouple power supply further away from the plasma reactor. I worked with another intern, Daniel Santander, who developed a space plant chamber which uses CO2 and H2O (harvested from the plasma reactor) to grow plants in space. The chamber possess a CO2 monitor, which controls the amount of gas that enters the chamber, along with a water integration system to supply the amount of water needed for proper plan growth. This technology will then be used for plant growth in space for the Astronauts on future space flights and possibly on the International Space Station (ISS). The second project I worked on is the “Orbital Syngas / Commodity Augmentation Reactor (OSCAR)” which focuses on the issues experienced in long-duration space flight regarding waste disposal. In previous space flight missions, waste was stored on board and returned to Earth for disposal. This technique is not applicable to long space flight missions to Mars due to the rocket being months away from Earth. OSCAR is using microgravity waste disposal techniques to produce fuels from the recycled waste. The waste is converted to syngas through a thermal degradation process. This process helps create an environmentally friendly way to dispose and reuse trash on board the space craft. Currently waste is being tested in the form of cotton and plastics. OSCAR is designed as a microgravity reactor that is currently being tested in a drop tower rig at Glenn Research Center. I helped design the 3D model for the insulation that will line the reactor. The first few trials, I dissolved the plastic of the mold in acetone. This method worked, but was very costly. I then received a silicone material to construct the mold from Swamp Works here at Kennedy. Through multiple trials with the silicone, this method worked best for developing the end pieces of the insulation for the chamber.

Plasma↗
NASA NTRSDate not supplied

Assessment of the Fluid Network for the Effusion Holes in a RQL (Rich-burn, Quick-quench, Lean-burn) Gas Turbine Combustor

The transient processes involving lean blowout (LBO) in a RQL combustor such as the single cup combustor in the National Jet Fuels Combustion Program (NJFCP) referee rig are simulated with the reduced mechanisms based on Hybrid Chemistry for three different fuels, A2, C1 and C4. Experiments conducted in the NJFCP referee rig established a stable flame at a global equivalence ratio of 0.096 (the near LBO condition) as the starting condition for LBO tests performed with all A and C fuels. Simulations of the approach to LBO verify that a stable flame is established at the near-LBO condition for each fuel before reducing fuel flow rate (and thus equivalence ratio) in a stepwise manner. Main conclusions are: (1) For A2 fuel the equivalence ratio for LBO is 0.081 (2) For C1 fuel the equivalence ratio for LBO is 0.087 or 0.085depended on different step-down transition paths. (3) For C4 fuel the equivalence ratio for LBO is 0.087 or 0.084 depended on types of mesh or boundary conditions. (4) The fuel relative difference from LES on LBO for C1 fuel relative to A2 fuel is 7.40% or 4.94% versus 7.83% from the experimental data. (5) The fuel relative difference from LES on LBO for C4 fuel relative to A2 is 6.17% or 7.69% versus 5.21% from the experimental data

Lean blow out↗
NASA NTRSDate not supplied

Assessment of the Fluid Network for the Effusion Holes in a RQL (Rich-burn, Quick-quench, Lean-burn) Gas Turbine Combustor

The transient processes involving lean blowout (LBO) in a RQL combustor such as the single cup combustor in the National Jet Fuels Combustion Program (NJFCP) referee rig are simulated with the reduced mechanisms based on Hybrid Chemistry for three different fuels, A2, C1 and C4. Experiments conducted in the NJFCP referee rig established a stable flame at a global equivalence ratio of 0.096 (the near LBO condition) as the starting condition for LBO tests performed with all A and C fuels. Simulations of the approach to LBO verify that a stable flame is established at the near-LBO condition for each fuel before reducing fuel flow rate (and thus equivalence ratio) in a stepwise manner. Main conclusions are: (1) For A2 fuel the equivalence ratio for LBO is 0.081 (2) For C1 fuel the equivalence ratio for LBO is 0.087 or 0.085 depended on different step-down transition paths. (3) For C4 fuel the equivalence ratio for LBO is 0.087 or 0.084 depended on types of mesh or boundary conditions. (4) The fuel relative difference from LES on LBO for C1 fuel relative to A2 fuel is 7.40% or 4.94% versus 7.83% from the experimental data. (5) The fuel relative difference from LES on LBO for C4 fuel relative to A2 is 6.17% or 7.69% versus 5.21% from the experimental data.

Lean Blow out↗
NASA NTRS1983

Importance of inlet boundary conditions for numerical simulation of combustor flows

Fluid dynamic computer codes for the mathematical simulation of problems in gas turbine engine combustion systems are required as design and diagnostic tools. To eventually achieve a performance standard with these codes of more than qualitative accuracy it is desirable to use benchmark experiments for validation studies. Typical of the fluid dynamic computer codes being developed for combustor simulations is the TEACH (Teaching Elliptic Axisymmetric Characteristics Heuristically) solution procedure. It is difficult to find suitable experiments which satisfy the present definition of benchmark quality. For the majority of the available experiments there is a lack of information concerning the boundary conditions. A standard TEACH-type numerical technique is applied to a number of test-case experiments. It is found that numerical simulations of gas turbine combustor-relevant flows can be sensitive to the plane at which the calculations start and the spatial distributions of inlet quantities for swirling flows.

Sturgess, G. J.↗
NASA NTRS2017

Application of Background Oriented Schlieren for Altitude Testing of Rocket Engines

A series of experiments was performed to determine the feasibility of using the Background Oriented Schlieren, BOS, flow visualization technique to image a simulated, small, rocket engine, plume under altitude test conditions. Testing was performed at the NASA Glenn Research Centers Altitude Combustion Stand, ACS, using nitrogen as the exhaust gas simulant. Due to limited optical access to the facility test capsule, all of the hardware required to conduct the BOS were located inside the vacuum chamber. During the test series 26 runs were performed using two different nozzle configurations with pressures in the test capsule around 0.3 psia. No problems were encountered during the test series resulting from the optical hardware being located in the test capsule and acceptable resolution images were captured. The test campaign demonstrated the ability of using the BOS technique for small, rocket engine, plume flow visualization during altitude testing.

Background Oriented Schlieren↗
NASA NTRSDate not supplied

Computational Fluid Dynamics Simulation of the Swordfish Oxygen/Methane Rotating Detonation Rocket Engine

Rotating Detonation Rocket Engines (RDREs) provide several theoretical performance benefits over traditional deflagration combustion rocket engines. RDREs can potentially generate higher specific impulse (ISP) for a given propellant combination enabling significant consumable mass savings for a spaceflight vehicle. Conversely, RDREs are a relatively new technology with a shallower analytical modeling base compared to traditional combustion engine architectures. In this work, we utilize time-accurate, Computational Fluid Dynamics (CFD) modeling to simulate the complex fluid environment inside an RDRE combustion chamber and propellant manifolds. The selected engine of study is the Swordfish RDRE which was developed and tested and at the National Aeronautics and Space Administration (NASA) Marshall Space Flight Center (MSFC). CFD simulations were conducted using the as-tested Swordfish geometry and conditions to facilitate comparison between the analytical predictions and experimental results.

Brian R. Richardson↗
NASA NTRS2002

Annual Research Briefs, 2002: Center for Turbulence Research

Turbulent combustion remains the largest component of the CTR's core program. This program and several related activities at CTR are supported by NASA's Ultra Efficient Engine Technology Program. It is also intimately connected with the Department of Energy's ASCI program at Stanford which develops the technology for numerical simulation of realistic aircraft engines using state of the art massively parallel computers. In combustion modeling the attention has been directed to the modeling of higher levels of complexity such as spray dynamics, radiation and soot formation. Major aircraft engine manufacturers have shown considerable interest in this program; in particular, a significant active collaboration exists between CTR and the Pratt & Whitney Corporation. CTR's combustion program is essentially based on the large-eddy simulation technique, LES, which is actively being pursued at CTR for this and many other applications. Important accomplishments in LES included simulations with three-dimensional filters which result in grid independent calculations (that is why we call it "true" LES), and the development of the methodology for integration of LES and Reynolds Averaged computations. Optimization techniques are being studied and used for the important problem of wall boundary conditions for LES as well as for optimal shape design for aeroacoustic and aerodynamic performance gains.

ULTRA EFFICIENT ENGINE TECHNOLOGY↗
NASA NTRS1985

Deposition of Na2SO4 from salt-seeded combustion gases of a high velocity burner rig

With a view to developing simulation criteria for the laboratory testing of high-temperature materials for gas turbine engines, the deposition rates of sodium sulfate from sodium salt-seeded combustion gases were determined experimentally using a well instrumented high-velocity burner. In the experiments, Na2SO4, NaCl, NaNO3, and simulated sea salt solutions were injected into the combustor of the Mach 0.3 burner rig operating at constant fuel/air ratios. The deposits formed on an inert rotating collector were then weighed and analyzed. The experimental results are compared to Rosner's vapor diffusion theory. Some additional test results, including droplet size distribution of an atomized salt spray, are used in interpreting the deposition rate data.

Santoro, G. J.↗
NASA NTRS1993

Source term evaluation for combustion modeling

A modification is developed for application to the source terms used in combustion modeling. The modification accounts for the error of the finite difference scheme in regions where chain-branching chemical reactions produce exponential growth of species densities. The modification is first applied to a one-dimensional scalar model problem. It is then generalized to multiple chemical species, and used in quasi-one-dimensional computations of shock-induced combustion in a channel. Grid refinement studies demonstrate the improved accuracy of the method using this modification. The algorithm is applied in two spatial dimensions and used in simulations of steady and unsteady shock-induced combustion. Comparisons with ballistic range experiments give confidence in the numerical technique and the 9-species hydrogen-air chemistry model.

Sussman, Myles A.↗
NASA NTRS1988

Numerical investigations in three-dimensional internal flows

Renewed interest in simulation of high enthalpy flows was brought about by interest in the design and testing of hypersonic propulsion components. This renewed interest has led to refurbishment of high speed ground based wind tunnel facilities. Simulation of the high enthalpy flows occurring in the NASP propulsion system is of particular interest. Studying the combustor presentes some of the more challenging problems in the ground based simulation of the fluid flow. A difficulty in simulating the required conditions at the entrance to the combustor is related to achieveing a sufficiently high static pressure such that combustion would be possible at a high Mach number. An analysis of the flow within the original nozzle was not performed previously using numerical simulations, although it was operated experimentally. A Navier-Stokes code was chosen in the present study to examine analytically the flow within representative selected nozzles for use in combustion experiments. The numerical simulation of these fluid flows is popular and may be able to shed light on the direction that redesign of the shock tube nozzles should take. The numerical codes were modified to account for the axially symmetric flow field, for the inclusion of equilibrium real gas effects and for ideal gases whose thermodynamic properties are frozen at the stagnation conditions. Numerical simulation of flows within the original and two proposed nozzles, including the energy lost to the relatively cold walls, are investigated.

Rose, William C.↗
NASA NTRS1988

Computer code for the prediction of nozzle admittance

A procedure which can accurately characterize injector designs for large thrust (0.5 to 1.5 million pounds), high pressure (500 to 3000 psia) LOX/hydrocarbon engines is currently under development. In this procedure, a rectangular cross-sectional combustion chamber is to be used to simulate the lower traverse frequency modes of the large scale chamber. The chamber will be sized so that the first width mode of the rectangular chamber corresponds to the first tangential mode of the full-scale chamber. Test data to be obtained from the rectangular chamber will be used to assess the full scale engine stability. This requires the development of combustion stability models for rectangular chambers. As part of the combustion stability model development, a computer code, NOAD based on existing theory was developed to calculate the nozzle admittances for both rectangular and axisymmetric nozzles. This code is detailed.

Nguyen, Thong V.↗
NASA NTRS2003

Unstructured LES of Reacting Multiphase Flows in Realistic Gas Turbine Combustors

As part of the Accelerated Strategic Computing Initiative (ASCI) program, an accurate and robust simulation tool is being developed to perform high-fidelity LES studies of multiphase, multiscale turbulent reacting flows in aircraft gas turbine combustor configurations using hybrid unstructured grids. In the combustor, pressurized gas from the upstream compressor is reacted with atomized liquid fuel to produce the combustion products that drive the downstream turbine. The Large Eddy Simulation (LES) approach is used to simulate the combustor because of its demonstrated superiority over RANS in predicting turbulent mixing, which is central to combustion. This paper summarizes the accomplishments of the combustor group over the past year, concentrating mainly on the two major milestones achieved this year: 1) Large scale simulation: A major rewrite and redesign of the flagship unstructured LES code has allowed the group to perform large eddy simulations of the complete combustor geometry (all 18 injectors) with over 100 million control volumes; 2) Multi-physics simulation in complex geometry: The first multi-physics simulations including fuel spray breakup, coalescence, evaporation, and combustion are now being performed in a single periodic sector (1/18th) of an actual Pratt & Whitney combustor geometry.

Ham, Frank↗
NASA NTRS1999

Monte Carlo Simulation of Nanoparticle Encapsulation in Flames

Gas-phase combustion (flame) synthesis has been an essential industrial process for producing large quantities of powder materials such as carbon black, titanium dioxide, and silicon dioxide. Flames typically produce simple oxides, with carbon black being the noted exception because the oxides of carbon are gaseous and are easily separated from the particulate matter that is formed during fuel pyrolysis. Furthermore, the powders produced in flames are usually agglomerated, nanometer-sized particles (nanoparticles). This composition and morphology is acceptable for many applications. However, the present interest in nanoparticles for advanced materials application has led to efforts to employ flames for the synthesis of unagglomerated nanoparticles (2 to 100 nm) of metals and non-oxide ceramics. Sodium-halide chemistry has proven to be viable for producing metals and non-oxide ceramics in flames. Materials that have been produced to date include Si (Calcote and Felder, 1993), TiN, TiB2, TiC, TiSi2, SiC, B4C (Glassman et al, 1993) Al, W, Ti, TiB2, AlN, and W-Ti and Al-AlN composites (DuFaux and Axelbaum, 1995, Axelbaum et al 1996,1997). Many more materials are possible. The main challenge that faces application of flame synthesis for advanced materials is overcoming formation of agglomerates in flames (Brezinsky, 1997). The high temperatures and high number densities in the flame environment favor the formation of agglomerates. Agglomerates must be avoided for many reasons. For example, when nanopowders are consolidated, agglomerates have a deleterious effect on compaction density, leading to voids in the final part. Efforts to avoid agglomeration in flames without substantially reducing particle number density and, consequently, production rate, have had limited success. Another critical challenge that faces all synthesis routes for nanopowders is ensuring that the powders are high purity and that the process is scaleable. Though the containerless, high temperature environment of a flame is excellent for producing high-purity simple compounds, ultrafine metals and non-oxide ceramic powders are inherently reactive in the presence of oxygen and/or moisture. Thus, the handling of these powders after synthesis poses a challenging problem. Impurities acquired during handling of nanoparticles have plagued the advancement of nanostructured materials technology.

Sun, Z.↗
NASA NTRS1993

In-stream measurements of combustion during Mach 5 to 7 tests of the Hypersonic Research Engine (HRE)

Results of in-stream combustion measurements taken during Mach 5 to 7 true simulation testing of the Hypersonic Research Engine/Aerothermodynamic Integration Model (HRE/AIM) are presented. These results, the instrumentation techniques, and configuration changes to the engine installation that were required to test this model are described. In test runs at facility Mach numbers of 5 to 7, an exhaust instrumentation ring which formed an extension of the engine exhaust nozzle shroud provided diagnostic measurements at 10 circumferential locations in the HRE combustor exit plane. The measurements included static and pitot pressures using conventional conical probes, combustion gas temperatures from cooled-gas pyrometer probes, and species concentration from analysis of combustion gas samples. Results showed considerable circumferential variation, indicating that efficiency losses were due to nonuniform fuel distribution or incomplete mixing. Results using the Mach 7 facility nozzle but with Mach 6 temperature simulation, 1590 to 1670 K, showed indications of incomplete combustion. Nitric oxide measurements at the combustor exit peaked at 2000 ppmv for stoichiometric combustion at Mach 6.

Lezberg, Erwin A.↗
NASA NTRS1982

Plane flame furnace combustion tests on JPL desulfurized coal

The combustion characteristics of three raw bituminous (PSOC-282 and 276) and subbituminous (PSOC-230) coals, the raw coals partially desulfurized (ca -60%) by JPL chlorinolysis, and the chlorinated coals more completely desulfurized (ca -75%) by JPL hydrodesulfurization were determined. The extent to which the combustion characteristics of the untreated coals were altered upon JPL sulfur removal was examined. Combustion conditions typical of utility boilers were simulated in the plane flame furnace. Upon decreasing the parent coal voltaile matter generically by 80% and the sulfur by 75% via the JPL desulfurization process, ignition time was delayed 70 fold, burning velocity was retarded 1.5 fold, and burnout time was prolonged 1.4 fold. Total flame residence time increased 2.3 fold. The JPL desulfurization process appears to show significant promise for producing technologically combustible and clean burning (low SO3) fuels.

Reuther, J. J.↗