SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A coal-rock interface detector is presented which employs a radioactive source and radiation sensor. The source and sensor are separately and independently suspended and positioned against a mine surface of hydraulic pistons, which are biased from an air cushioned source of pressurized hydraulic fluid.
The overall objective of this project is to produce a rare earth elements product with greater than 8% rare earth elements from coal-based resources using an economically viable and environmentally benign processing methodology. The objective of the coal processing work will be to acquire appropriate coal feed and produce a viable clean coal product, a concentrated REE feed stream, and a pyrite stream (where available) that can be used to enhance leaching. The objective of the bio-oxidation portion of the project is to utilize bacteria to oxidize sulfide minerals and ferrous ions to ferric ions to accelerate leaching and remove the sulfides to prevent future acid mine drainage and related liabilities. The objective of the solution conditioning work is to remove iron and control leaching solution conditions to facilitate extraction of REEs without significant thorium extraction. The objective of the column leaching work is to engineer/model and simulate heap leaching to demonstrate low-cost extraction of REEs from coal-based resources. The objective of the solvent extraction work is to selectively extract and recover through controlled stripping of REEs that are solubilized through leaching. The objective of the precipitation portion of the project is to recover the REEs from the solvent extraction stripping solutions and dry them to achieve the final product of rare earth elements that is > 8 % REEs. The objective of the technical, economic, and environmental analysis is to determine the overall viability of the processing approach that is demonstrated in this project
Coal is increasingly evaluated as a source of rare earth elements (REEs) in the United States to address the overreliance on imported REEs. The objective of this study was to assess the distribution of REEs in lignites from selected mining areas in the Texas Gulf Coastal Plain region. Thirty-one archived lignite and rock samples previously collected by the U.S. Geological Survey were analyzed for their rare earth element and critical mineral content. These include samples from one core (5400 and 5500 lignite horizons) and two opencast lignite mines (Gibbons Creek 3500 and 4500 horizons, and San Miguel horizons A to D) in the Eocene Jackson Group of the Texas Gulf of Mexico Coastal Plain. Some lithologies in the Gibbons Creek 3500 and 4500 lignite-bearing sections have high total rare earth, yttrium (Y), and scandium (Sc) (REYSc) values, up to 7800 ppm (ash basis) REYSc. The lignite lithologies show an enrichment in rare earths, [samarium (Sm) through gadolinium (Gd)]. The basal Gibbons Creek 3500 lignite bench shows a heavy rare earth element enrichment pattern resembling that often seen in peats through high volatile A bituminous coals. The 5500 lignite sequence, overlying the latter lignite sections, shows a light rare earth enrichment. The San Miguel lignite benches have heavy rare earth enrichments with a negative europium (Eu) anomaly.
The electricity generation sector is responsible for 25% of the world’s greenhouse gas (GHG) emissions and thus has been the focus of efforts to transition to clean energy and sustainable development in many nations. In the past 20 years, renewable energy sources have been the fastest-growing energy source in the world, comprising almost 29% of the world’s electricity generation in 2020. Renewable energy sources are expected to comprise nearly 95% of the world’s power capacity growth through 2026, with a share of planned capacity expansion of up to 46% in 2026. The rapid development of renewable energy sources and technologies will require an enormous amount of raw materials to replace coal and gas plants and increase in the capacity to handle growing electricity demand because renewable energy sources have a low-power density and intermittent behavior. Accounting for the expected scale of rapidly deploying renewable energy sources that require rare earth elements (REEs), cement, and steel, the mining industry may face a supply problem for the materials critical for clean energy. And, as the exploration and development of new mining sites can be expensive and risky, the mining industry may require economic stimuli to grow supply. The increasing demand for renewable energy resources makes mining a threat to the environment unless proper regulations are established and calls for remining, cleanup, and circular economic development are made. Mining also contributes to environmental injustices related to the exploitation and pollution of lands near communities that are dependent on biodiversity in the area, while not always benefiting from technological advancements provided by the use of renewable energy and technologies. This study explored the opportunity of remining abandoned mining waste to extract metals and minerals essential for the production of renewable energy sources. The authors analyzed materials used in the production of these technologies, materials readily available in the United States, and which materials can be extracted locally in the United States from abandoned mine waste. The authors also studied environmental injustices that populations near mining sites experience and ways to mitigate these injustices, such as providing more control over extraction and cleanup activities, providing more job opportunities in those areas, and offsetting costs associated with cleanup and land restoration projects.
An existing image processing system is adapted to describe the geologic attributes of a regional coal basin. This scheme handles a map as if it were a matrix, in contrast to more conventional approaches which represent map information in terms of linked polygons. The utility of the image processing approach is demonstrated by a multiattribute analysis of the Herrin No. 6 coal seam in Illinois. Findings include the location of a resource and estimation of tonnage corresponding to constraints on seam thickness, overburden, and Btu value, which are illustrative of the need for new mining technology.
The following document summarizes project results from “CORE-CM in the Greater Green River and Wind River Basins: Transforming and Advancing a National Coal Asset”. This project is part of the U.S. Department of Energy’s (“DOE”) National Energy Technology Laboratory’s (“NETL”) Carbon Ore, Rare Earth Elements, and Critical Minerals (CORE-CM) Initiative. This report concludes that the Greater Green River and Wind River Basins (GGRB-WRB) Area-of-Interest (AOI 9) is the ideal region for continued research and development in progressing the broader CORE-CM goals outlined by the DOE. Based upon the extensive analyses of technical, social, and community criteria, this report illustrates that the GGRB-WRB hosts numerous potential CORE-CM feedstocks (both coal- and non-coal based), diverse opportunities for utilizing existing industrial waste streams, ample infrastructure and industry to support new CORE-CM-focused technologies, and a highly motivated, well educated, and adaptable workforce to further develop the regional and national CORE-CM supply chain. Additionally, some potential solutions for technological gaps suggest that the GGRB-WRB's diverse resources can play a significant role in achieving the national goal of critical materials independence. With full community participation, meaningful involvement of regional Tribal Nations, and building upon the stakeholder engagement demonstrated here, the GGRB-WRB region presents a unique opportunity for advancing the CORE-CM Initiative. This project was designed to bring together coal-based communities and stakeholders from across the GGRB-WRB to advance new industries for CORE-CM resources. The University of Wyoming (UWyo) School of Energy Resources (SER) led a project team of experts from the Colorado Geological Survey (CGS), Colorado School of Mines (CSM), Los Alamos National Lab (LANL), and local community colleges. Input from basinal, regional, and national experts bolstered the coalition in order to advance the mission of DOE’s CORE-CM initiative and develop the domestic CORE-CM supply chain. Phase I of this project was designed to address the goal of developing and catalyzing economic growth, job creation, and technology innovation in the GGRB-WRB of Wyoming and Colorado, by increasing the supply of CORE-CM to manufacturers of non-fuel Carbon Based Products (CBP) and products reliant upon CM. The GGRB-WRB CORE-CM project worked toward providing benefit through several avenues of performance and research. • Develop a coalition team to achieve project objectives • Complete detailed assessments, including State-of-the-Art (SOTA) Data acquisition of potential CORE-CM materials across the AOI, and meaningfully contributes to DOE’s CORE-CM goals nationally. • Strategic planning for regional economic growth, job creation, and associated technology innovation around coal materials, including plans to maximize the development of potential CORE-CM resources and technology by creating regional public-private partnerships. • Define regional economic growth potential around existing strengths, energy infrastructure, business and industry, including planning for the leveraging of highly trained workforces, existing and novel coal technologies, and energy infrastructure in development of CORE-CM supply chains. • Develop a preliminary strategic plan for increasing the supply of CORE-CM materials to manufacturers of non-fuel Carbon Based Products (CBP) and products reliant upon CM, focusing on regional strengths that result in an emerging diversified CORE-CM economy. • Assemble a committed network of stakeholders and communities that learn about, accept, and grow new energy technologies within coal regions. Additionally, the project team significantly contributed to the CORE-CM Initiative’s national goals, through cross-regional scoping, collaborating with CORE-CM projects in other AOIs, and including parallel regional project experts. In addition to active inclusion and meaningful engagement and contribution to DOE-led working groups, the project team focused on engaging with regional communities including Tribal Nations, economic development groups, and regional government organizations. The project’s CORE-CM development and commercialization plan identified diverse CORECM feedstocks, potential routes towards integration with existing industries, methods for supply-chain development that leverage existing infrastructure and businesses considering the regional economy, identified entry barriers for incorporating traditional and new technologies in those supply chains, recognized opportunities for public-private partnerships to develop technology innovation centers, identified diverse workforces, and conducted stakeholder outreach and education to build a community of understanding on CORE-CM potential in the GGRB-WRB region. Detailed task descriptions can be found in each chapter.
Two-phase reacting flows are substantially less understood compared to gas phase flows. While extensive work has been done on sprays, less attention has been given to the details of dusty reacting flows. Dusty flows are of particular interest for a wide range of applications. Particles can be present in a gas intentionally or unintentionally, and they can be inert or reacting. Inert particles can be also present in an otherwise reacting gas flow, and that can lead to flame cooling and modification of the extinction limits of a combustible mixture. Reacting solid particles can release substantial amounts of heat upon oxidation, and can be used either for propulsion (e.g. Al, B, Mg) or power generation (coal). Furthermore, accidents can occur when a reacting dust accumulates in air and which, in the presence of an ignition source, can cause explosion. Such explosions can occur during lumber milling, in grain elevators, and in mine galleries.
As a gross measure of the economics of mining lunar sources of He-3, the energy densities (GJ/ton) of lunar soils were compared with the energy densities of various existing and future terrestrial sources of energy. On this basis, only the very richest lunar ores appear competitive with coal. Future lunar exploration might emphasize identification of lunar soils having higher concentrations of He-3.
Critical minerals (CM) supply raw materials that constitute many of our essential infrastructure, defense, technology, and electrification needs. Currently, production and refinement of these materials from conventional sources is limited to few regions globally, which makes supply of these resources particularly venerable to disruption. To help overcome these risks and meet growing demand, attention has focused on identifying and developing resource potential of unconventional geologic CM sources, such as rare-earth elements in sedimentary systems. However, the unconventional nature of these types of sources means they are often poorly characterized and/or under-explored with respect to conventional counterparts. We present a regional case study for an Unconventional Rare-earth and Critical minerals (URC) assessment method for predicting and identifying REE resource potential and occurrence in unconventional systems in the Central Appalachian Basin (CAB). The method utilizes a geologic and geospatial data-driven approach, informed and guided by knowledge of REE enrichment processes, to systematically predict and identify areas of higher enrichment. Results from the test case indicate locations with potential for different types of coal-REE deposits, demonstrating its utility for reducing the area of exploration and identifying sites for more detailed investigation. Building upon the regional scale assessment capability, ongoing science-based enhancements to the method will allow for finer-scale (e.g., mine-scale) predictions required to support technical and economic assessments.
Rare earth elements (REE) are critical ingredients of sustainable energy technologies, but their extraction from ore and separation from one another pose formidable challenges. To solve the challenge of REE supply, we used advanced genomics, high-throughput screening with synthetic REE minerals, and synthetic biology to engineer two sets of exotic microbes to (1) extract REE from ores, spent cracking catalysts, coal ash and electronic waste with high efficiency and selectivity, and (2) to purify REE into single element batches, all under benign conditions without the need of harsh solvents and high temperatures. This work integrated our expertise in systems and synthetic biology (Buz Barstow); rare-earth geochemistry (Esteban Gazel) and mineral synthesis (Megan Holycross); and microsystems engineering (Mingming Wu) by first elucidating the set of rules that predict an organism’s phenotype and then applying them to solve this critical problem in sustainable energy. These new technologies could help to revitalize the US rare earth industry and provide a new source of these critical elements for future energy technologies. We have already had some big success in tech transfer. Two of our team members (postdoctoral fellow Alexa Schmitz and graduate student Sean Medin) were able to study the supply chain for REE in the United States, and identify an opportunity to commercialize our REE mineral-dissolution technology. Alexa and Sean recently founded REEgen, Inc., an REE biomining company. Dr. Schmitz was recently awarded a fellowship from the Activate Foundation to support the first two years of REEgen. Cornell showed its support for this technology and company, and Dr. Schmitz was awarded the Rising Women Innovator’s award. These two awards unlocked support from Cornell’s Praxis Incubator.
Since the 1920s, the only respiratory protection which coal miners had available during exposure to toxic or irrespirable environments was a filter self-rescuer that catalytically converted carbon monoxide (CO) to carbon dioxide (CO2). The deficiencies of this self-rescuer, which have been described elsewhere (37) led to the support by the Bureau of Mines of the development of a new generation of self-rescuers which utilized potassium superoxide (KO2) as the air-revitalization chemical. Since KO2 reacts with exhaled breath and releases oxygen (O2) while it absorbs CO2, the new self-rescuers were closed-circuit devices which isolated the miner from contact with toxic or irrespirable atmospheres. A device with a one-h duration developed by Lockheed under contract with the Bureau of Mines (18) utilized 1.5 Ib of KO2, weighed 4.54 Ib and measured 6.5 by 3.6 by 7.7 in. Since the earlier, filter self-rescuer weighed about 2.5 lb and was worn continuously by the miner, the one-h, KO2-based device represented a substantial addition to the equipment that the miner was accustomed to carrying and, therefore, was considered to be too large and too heavy.
Qualitative and quantitative evaluation methods for coal extraction systems were developed. The analysis examines the soundness of the design, whether or not the major hazards have been eliminated or reduced, and how the reduction would be accomplished. The quantitative methodology establishes the approximate impact of hazards on injury levels. The results are weighted by peculiar geological elements, specialized safety training, peculiar mine environmental aspects, and reductions in labor force. The outcome is compared with injury level requirements based on similar, safer industries to get a measure of the new system's success in reducing injuries. This approach provides a more detailed and comprehensive analysis of hazards and their effects than existing safety analyses.
The primary objective of this CarbonSAFE Phase II project was to establish the technical and commercial feasibility of a commercial-scale CO 2 geological storage complex for Deseret Power Electric Cooperative Bonanza Power Plant and other CO 2 sources in the northeast Uinta Basin, Utah, with the goal to securely store at least 50 million metric tons of captured CO 2 and accelerate CO 2 capture, utilization, and storage (CCUS) deployment. The project team established high-potential technical and commercial feasibility for a storage site within the east Uinta Basin (Utah), in the Cretaceous sandstones (Frontier, Dakota, and Buckhorn), Entrada Sandstone, Nugget Sandstone, and/or Weber Sandstone southwest of the Bonanza coal-fired power plant. This project collected and analyzed state-of-the-art data to characterize the storage complex consistent with Environmental Protection Agency (EPA) permitting standards. The team conducted extensive analog studies, outcrop mapping, and data sampling, which largely contributed to understanding the subsurface lithology and facies. Existing data were obtained and assessed from Utah Division of Oil, Gas, and Mining (DOGM), Utah Geological Survey (UGS), Colorado Geological Survey (CGS), U.S. Geological Survey (USGS), and EPA. These data were analyzed using state-of-the-art CCUS technologies for Societal Considerations, Site Characterization, Modeling and Simulations, Risk Assessment, Management and Monitoring, potential Underground Injection Control (UIC) Class VI Well Permitting, and Technical/Economic Feasibility. Through these high-resolution data collection and feasibility studies, this project was expected to provide a reference for initiating Underground Injection Control (UIC) and other commercial-scale geological storage permitting processes in the Western United States, ultimately contributing to the nation's decarbonization goals through low-risk, cost-effective commercial-scale carbon capture, utilization, and storage (CCUS) projects.
The decline of coal use for energy production provides an abundance of local feedstock for new innovative uses and value-added products. Expanding the U.S. coal-value chain to manufacture high-value carbon products can strengthen the nation’s energy and mineral security, enhance the U.S. national defense security, increase the United States’ economic prosperity, while achieving U.S. environmental objectives. The primary project goal is a relatively light-weight composite product with superior (or comparable) compressive strength. Both virgin and, where available, post-consumer recycled thermoplastic versions are tested for each thermoplastic species. A useful attribute of thermoplastics as binders is that they can be heated to their melting point, cooled, and reheated again without significant degradation. A key advantage of thermoset CBBs is that they require only mixing and molding. CBB advantages include low cost, availability, binding ability and processability. Coal-based bricks and blocks (CBBs) weigh about 50% less than clay bricks and can be manufactured with an interlocking design to promote ease of use for the novice builder. CBB formulation is evaluated according to a design-of-experiments (DoE) approach. DoE variables are a) relative weight fractions of binder, b) relative proportions of large versus small (milled) anthracite size fractions, and c) additive percentage. Fabrication methods include hot-press molding and extrusion, the later being the most commercially viable. CBBs are tested for compressive strength, modulus of rupture (by flexure test) and water absorption per ASTM C67, with density determined by the Archimedes drainage method. Fractured interfaces are examined by SEM (Scanning Electron Microscopy) to resolve fracture dynamics and interior microstructure uniformity. Differential scanning calorimetry (DSC) is used to compare plastic transition temperatures i.e., glass and melting temperatures to contrast virgin with post-consumer recycled thermoplastics and optimize their usage. These results are used in the DoE analysis to identify the binder and relative weight percentages for optimum strength, density, and porosity. Overall, CBBs possess strength comparable to clay-based bricks but are non-permeable and hydrophobic, and hence resistant to degradation by freeze-fracturing, corrosion, and efflorescence. The strongest composites have been made with the following thermoplastic binders (in order of strength): thermoset, high-density polyethylene crosslink resin, high-density polyethylene, nylon 6/6, and polypropylene. Results from a techno-economic analysis TEA show economy of scale for CBBs by modularization and reveal the binder as the cost driver for material costs. Ideally, the incorporation of post-consumer recycled thermoplastic will decrease material acquisition costs and increase product sustainability. Notably, CBBs do not require the high temperature calcination needed to produce cement, nor do they require firing in the 1600-2400 °F range for three days using natural gas, as do clay brick equivalents. Instead, CBBs are heated to a modest <600 °F according to the melt flow index of the thermoplastic binder. Existing anthracite mines can be expanded to produce CBBs to reduce aggregate transportation costs and emissions that exist for clay bricks. TEA reflects this reduced energy cost while a comparative CO2 emission analysis quantifies the reduced environmental footprint. The market survey identifies several commercialization opportunities, dependent upon the brick classification.
Naturally occurring organic materials containing humic acids show a strong affinity towards rare earth elements (REE) and other critical elements. Leaching experiments on lignite coal waste produced from construction sand production revealed that the contained REEs were associated with the organic matter. Furthermore, adsorption studies revealed that the lignite waste was capable of extracting REEs from a model solution and increased the REE content of the lignite waste by more than 100%. As such, this study aimed to utilize the lignite waste to adsorb REEs from pregnant leach solutions and acid mine drainage sources having low REE concentrations and subsequently leach the lignite material to produce pregnant leach solutions containing relatively high amounts of REEs, which benefits the performance and economic viability of downstream separation and purification processes. An integrated flowsheet was developed based on this concept and tested at a pilot scale. The pregnant leachate solution (PLS) was generated from a heap leach pad containing 2000 tons of Baker seam coarse refuse. The pilot scale circuit was comprised of aluminum precipitation, adsorption using the waste lignite, and rare earth-critical metal (RE-CM) precipitation stages in succession. The results indicated that the aluminum precipitation stage removed over 88% and 99% of the Al and Fe, respectively. The adsorption stage increased the REE content associated with the waste lignite from 457 ppm to 1065 ppm on a whole mass basis. Furthermore, the heavy REE (HREE) content in the feedstock increased by approximately 250%, which raised the percentage of HREE in the REE distribution by 19 absolute percentage points. In addition to the REEs, concentrations of other critical elements such as Mn, Ni, and Zn also improved by 75%, 37%, and 250%, respectively. Bench-scale tests revealed that increasing the solids concentration in the waste lignite and PLS mix from 1% to 20% by weight enhanced the adsorption efficiency from 32.0% to 99.5%, respectively. As such, a new flowsheet was proposed which provides significantly higher REE concentrations in the PLS that can be fed directly to solvent extraction and/or oxalic acid precipitation and, thereby, enhancing process efficiency and economics.
ABSTRACT Hydrologic connectivity is defined as the connection among stores of water within a watershed and controls the flux of water and solutes from the subsurface to the stream. Hydrologic connectivity is difficult to quantify because it is goverened by heterogeniety in subsurface storage and permeability and responds to seasonal changes in precipitation inputs and subsurface moisture conditions. How interannual climate variability impacts hydrologic connectivity, and thus stream flow generation and chemistry, remains unclear. Using a rare, four‐year synoptic stream chemistry dataset, we evaluated shifts in stream chemistry and stream flow source of Coal Creek, a montane, headwater tributary of the Upper Colorado River. We leveraged compositional principal component analysis and end‐member mixing to evaluate how seasonal and interannual variation in subsurface moisture conditions impacts stream chemistry. Overall, three main findings emerged from this work. First, three geochemically distinct end members were identified that constrained stream flow chemistry: reach inflows, and quick and slow flow groundwater contributions. Reach inflows were impacted by historic base and precious metal mine inputs. Bedrock fractures facilitated much of the transport of quick flow groundwater and higher‐storage subsurface features (e.g., alluvial fans) facilitated the transport of slow flow groundwater. Second, the contributions of different end members to the stream changed over the summer. In early summer, stream flow was composed of all three end members, while in late summer, it was composed predominantly of reach inflows and slow flow groundwater. Finally, we observed minimal differences in proportional composition in stream chemistry across all four years, indicating seasonal variability in subsurface moisture and spatial heterogeneity in landscape and geologic features had a greater influence than interannual climate fluctuation on hydrologic connectivity and stream water chemistry. These findings indicate that mechanisms controlling solute transport (e.g., hydrologic connectivity and flow path activation) may be resilient (i.e., able to rebound after perturbations) to predicted increases in climate variability. By establishing a framework for assessing compositional stream chemistry across variable hydrologic and subsurface moisture conditions, our study offers a method to evaluate watershed biogeochemical resilience to variations in hydrometeorological conditions.
The basic behavior of mining crushed goods in chain scraper conveyors was examined using a special test stand. The characteristics resistance lines of the upper end-piece were determined for conveyor idle as a function of the determinative crushed good characteristics (granular structure, moisture content, type of goods) on the size of the conveyor load, on the conveyor construction and on the stopped time of the conveyor. Crushed goods with a narrow granular profile and sphere-like grains caused about 35% greater resistance than fine coal and raw coal with broad granular profile. For goods containing water more than 10% by weight, the solids friction retreated in favor of flow friction. The coefficient of resistance decreased considerably in the range of lower speeds and then increased with increasing conveyor speed. The conveyance of sandstone ore required about 280% greater specific drive than the conveyance of raw coal. Resistance coefficients for coal and raw coal showed no dependence on the design of the conveyor. Start-up of loaded conveyors after longer stop times was simulated and the specific break-loose force was determined.
Spatiotemporal variability in the carbon isotope composition of sedimentary organic matter (OM) preserves information about the evolution of the biosphere and of the exogenic carbon cycle as a whole. Primary compositions, and imprints of the post-depositional processes that obscure them, exist at the scale of individual sedimentary grains (mm to micron). Secondary ion mass spectrometry (SIMS) (1) enables analysis at these scales and in petrographic context, (2) permits morphological and compositional characterization of the analyte and associated minerals prior to isotopic analysis, and (3) reveals patterns of variability homogenized by bulk techniques. Here we present new methods for in situ organic carbon isotope analysis with sub-permil precision and spatial resolution to 1 micron using SIMS, as well as new data acquired from a suite of Archean rocks. Three analytical protocols were developed for the CAMECA ims1280 at WiscSIMS to analyze domains of varying size and carbon concentration. Average reproducibility (at 2SD) using a 6 micron spot size with two Faraday cup detectors was 0.4 %, and 0.8 % for analyses using 1 micron and 3 micron spot sizes with a Faraday cup (for C-12) and an electron multiplier (for C-13). Eight coals, two ambers, a shungite, and a graphite were evaluated for micron-scale isotopic heterogeneity, and LCNN anthracite (delta C-13 = -23.56 +/- 0.1 %, 2SD) was chosen as the working standard. Correlation between instrumental bias and H/C was observed and calibrated for each analytical session using organic materials with H/C between 0.1 and 1.5 (atomic), allowing a correction based upon a C-13H/C-13 measurement included in every analysis. Matrix effects of variable C/SiO2 were evaluated by measuring mm to sub-micron graphite domains in quartzite from Bogala mine, Sri Lanka. Apparent instrumental bias and C-12 count rate are correlated in this case, but this may be related to a crystal orientation effect in graphite. Analyses of amorphous Archean OM suggest that instrumental bias is consistent for 12C count rates as low as 10% relative to anthracite. Samples from the ABDP-9 (n=3; Mount McRae Shale, approximately 2.5 Ga), RHDH2a (n=2; Carrawine Dolomite and Jeerinah Fm, approximately 2.6 Ga), WRL1 (n=3; Wittenoom Fm, Marra Mamba Iron Formation, and Jeerinah Fm, approximately 2.6 Ga), and SV1 (n=1; Tumbiana Fm, approximately 2.7 Ga) drill cores, each previously analyzed for bulk organic carbon isotope composition, yielded 100 new, in situ data from Neoarchean sedimentary OM. In these samples, delta C-13 varies between -53.1 and -28.3 % and offsets between in situ and bulk compositions range from -8.3 to 18.8%. In some cases, isotopic composition and mode of occurrence (e.g. morphology and mineral associations) are statistically correlated, enabling the identification of distinct reservoirs of OM. Our results support previous evidence for gradients of oxidation with depth in Neoarchean environments driven by photosynthesis and methane metabolism. The relevance of these findings to questions of bio- and syngenicity as well as the alteration history of previously reported Archean OM will be discussed.