Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COMPRESSION RATIO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Potential Impacts of High-Octane Fuel Introduction in a Naturally Aspirated, Port Fuel-Injected Legacy Vehicle

In recent years there has been an increased interest in raising the octane level of gasoline to enable higher compression ratios (CR) in spark-ignition engines to improve vehicle fuel efficiency. A number of studies have examined opportunities to increase efficiency in future vehicles, but potential impacts on the legacy fleet have not received as much attention. In this study, our effort focused on experimental studies on an engine using high-octane fuels without changing the engine’s CR. Spark timing was advanced until maximum torque was reached or knock was encountered for each engine condition, using each individual fuel to maximize engine efficiency. Knock-limited conditions occurred as the output brake mean effective pressure (BMEP) neared the maximum attainable output at a given engine speed. Increasing research octane numbers generally enabled knock-free operation under a greater number of operating conditions. Vehicle modeling using Autonomie was used to project vehicle energy use, fuel economy, and tailpipe CO 2 emissions for the Urban Dynamometer Driving Schedule (UDDS), the Highway Fuel Economy Test (HWFET), and the US06 cycle. Results show that decreases in energy consumption of up to 2% for a small SUV are possible through the use of a 97 RON fuel compared to a baseline using 91 RON fuel, provided that the formulation of the fuel does not cause unanticipated operational issues such as lower maximum BMEP. Greater improvements using high-octane fuels are possible if the CR is increased, but there is no opportunity to increase the CR in legacy vehicles. Thus, these vehicles realize an improvement from increased octane rating in accordance with their ability to spark advance to take advantage of a fuel with a higher octane rating. For the modeled vehicle, improvements of up to 2% in volumetric fuel economy may be possible through the use of a 97 RON fuel with the largest gains expected on the US06 cycle. Fuel economy impacts are strongly coupled to the heating value of the fuels in addition to changes in engine efficiency. Similarly, decreases in tailpipe CO 2 emissions are also achievable. However, simultaneous improvements in energy consumption, fuel economy, and tailpipe CO 2 emissions are not guaranteed and are dependent upon fuel formulation.

33 ADVANCED PROPULSION SYSTEMS↗

Lean-Stratified Combustion System with Miller Cycle for Downsized Boosted Application - Part 2

Automotive manufacturers relentlessly explore engine technology combinations to achieve reduced fuel consumption under continued regulatory, societal and economic pressures. For example, technologies enabling advanced combustion modes, increased expansion to effective compression ratio and reduced parasitics continue to be developed and integrated within conventional and hybrid propulsion strategies across the industry. Here, a high-efficiency gasoline engine capable for use in conventional or hybrid electric vehicle platforms is highly desirable. This paper is the second of two papers describing the multi-cylinder integration of a technology package combining lean-stratified combustion with Miller cycle for downsized boosted applications. The first paper describes the design, analysis and single-cylinder testing conducted to down-select the combustion system deployed to the multi-cylinder engine. This paper defines a light-duty engine package capable of achieving a 35% fuel economy improvement at US Tier 3 emission standards over a naturally aspirated stoichiometric baseline vehicle. A multi-mode combustion system was developed enabling highly efficient lean-stratified operation at light-load and stoichiometric Miller-cycle operation at mid- to high-loads. A central direct-injection four-valve layout was designed with high-tumble ports and a bowl-in-piston capable of stable operation under highly dilute mixtures when properly matched to fuel spray characteristics, injection strategy, and a high-energy ignition system. Boost system layout and base engine architecture were selected to minimize parasitics and maximize after treatment effectiveness. A multi-cylinder engine was developed and calibrated over a steady-state map. Results fed vehicle simulations over the EPA city and highway test cycles to predict the fuel economy improvement and tailpipe emissions potential. Fuel economy improvements over the baseline vehicle were projected at 42% and 39% for active-urea and passive-ammonia SCR after treatment systems respectively. Controls complexity to achieve regulatory compliance and the cost of the lean after treatment system were identified as the primary challenges to commercial viability.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Lean-Stratified Combustion System with Miller Cycle for Downsized Boosted Application - Part I

Automotive manufacturers relentlessly explore engine technology combinations to achieve reduced fuel consumption under continued regulatory, societal and economic pressures. For example, technologies enabling advanced combustion modes, increased expansion to effective compression ratio, and reduced parasitics continue to be developed and integrated within conventional and hybrid propulsion strategies across the industry. A high-efficiency gasoline engine capable for use in conventional or hybrid electric vehicle platforms is highly desirable. This paper is the first to two papers describing the development of a combustion system combining lean-stratified combustion with Miller cycle for downsized boosted applications. The work was completed under a multi-year US DOE project. The goal was to define a light-duty engine package capable of achieving a 35% fuel economy improvement at US Tier 3 emission standards over a naturally aspirated stoichiometric baseline vehicle. A multi-mode combustion system was developed enabling highly efficient lean-stratified operation at light-load and stoichiometric Miller-cycle operation at mid- to highloads. Some of the unique challenges in synergistically combining the two concepts are highlighted in this paper. Here, a central direct-injection four-valve layout was designed with high-tumble ports and a bowl-in-piston capable of stable operation under highly dilute (lean plus EGR) mixtures when properly matched to fuel spray characteristics, a multiple-injection strategy, and a high-energy ignition system. Other challenges specific to meeting exhaust emissions requirements with a high-efficiency engine are also explored in this study. In this Part 1 of the paper, the single-cylinder combustion system design, analysis, and testing is described. Multicylinder engine system design, analysis and development is described in Part 2 of the paper.

33 ADVANCED PROPULSION SYSTEMS↗

A Study of Propane Combustion in a Spark-Ignited Cooperative Fuel Research (CFR) Engine

Liquefied petroleum gas (LPG), whose primary composition is propane, is a promising candidate for heavy-duty vehicle applications as a diesel fuel alternative due to its CO 2 reduction potential and high knock resistance. To realize diesel-like efficiencies, spark-ignited LPG engines are proposed to operate near knock-limit over a wide range of operating conditions, which necessitates an investigation of fuel-engine interactions that leads to end-gas autoignition with propane combustion. This work presents both experimental and numerical studies of stoichiometric propane combustion in a sparkignited (SI) cooperative fuel research (CFR) engine. Engine experiments are initially conducted at different compression ratio (CR) values, and the effects of CR on engine combustion are characterized. A three-pressure analysis (TPA) model based on the two-zone combustion concept is developed in GT-Power and validated using test results to estimate in-cylinder wall temperatures, residual gas fraction, etc. This model is further utilized to examine end-gas chemistry by enabling the SI turbulent flame combustion and unburned gas chemical kinetics modules. Finally, a three-dimensional (3D) computational fluid dynamic (CFD) model of the CFR engine is developed in CONVERGE, where the G-equation and SAGE detailed chemical kinetics models are implemented for combustion modeling. Here, a 153 species reduced chemical kinetics mechanism derived from the detailed NUIGMech1.1 mechanism based on the ignition delay and laminar flame speed (LFS) studies is used to generate an LFS lookup table and to describe end-gas autoignition chemistry. Multi-cycle Reynolds-averaged Navier-Stokes (RANS) simulations are then performed for the tested CRs, and the numerical model is shown to be capable of predicting the propane combustion characteristics, particularly the end-gas autoignition behavior.

20 FOSSIL-FUELED POWER PLANTS↗

Experimental and Numerical Study on the Effect of Nitric Oxide on Autoignition and Knock in a Direct-Injection Spark-Ignition Engine

We report Nitric Oxide (NO) can significantly influence the autoignition reactivity and this can affect knock limits in conventional stoichiometric SI engines. Previous studies also revealed that the role of NO changes with fuel type. Fuels with high RON (Research Octane Number) and high Octane Sensitivity (S = RON – MON (Motor Octane Number)) exhibited monotonically retarding knocklimited combustion phasing (KL-CA50) with increasing NO. In contrast, for a high-RON, low-S fuel, the addition of NO initially resulted in a strongly retarded KL-CA50 but beyond the certain amount of NO, KL-CA50 advanced again. The current study focuses on same high-RON, low-S Alkylate fuel to better understand the mechanisms responsible for the reversal in the effect of NO on KLCA50 beyond a certain amount of NO. Experiments were conducted to measure the responses of KL-CA50 and trace-autoignition CA50, the latter being indicative of CA50 at which end-gas autoignition starts to become measurable from the apparent heat-release rate. Chemical-kinetics simulations were conducted to reveal the role of NO for end-gas autoignition, with a specific focus on sequential autoignition in a thermally stratified end-gas. The simulation results reveal that the magnitude of low-temperature heat release (LTHR) generally increases with NO. However, the relative importance of NO for enhancing LTHR diminishes when the LTHR inherent to a fuel’s chemistry is strong, such as at lower temperatures in a thermal boundary layer. This rendered more uniform LTHR within a hypothetical thermal boundary and led to a more sequential (i.e. slower) autoignition event. It was also revealed that a change in compression ratio influences the importance of intermediate-temperature heat release (ITHR) due to changes of the temperature-pressure history of the end-gas. Together with the condition where end-gas autoignition occurs more sequentially, the shorter time spent in LTHR and ITHR regime can counter the increase in autoignition reactivity at high NO levels and allow KLCA50 to advance

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Simultaneous Reduction of NOx and Fuel Consumption for Off-Road Powertrains

Simultaneously reducing criteria pollutants and fuel consumption is important for clean air and improving vehicle total cost of ownership. The goal of this effort was focused on a 90% NOx reduction and 10% fuel savings for an off-road 407 kW diesel engine. The baseline was a production Fiat Powertrain 13L engine and aftertreatment system meeting 0.4 g/kW-hr NOx. The baseline system was quantified over the NRTC, RMC, new low load cycle and five field cycles. A next generation engine was built incorporating several fuel-efficient design features, including a higher compression ratio, increased fuel-rail pressure, low-friction piston rings, and a high-efficiency variable-geometry turbocharger. Cylinder deactivation and EGR pump technologies were added to this engine as well. The combination was optimized prior to adding advanced aftertreatment systems, showing the trade-off of engine out NOx and exhaust temperature. Two next-generation catalyst technologies were employed into a LO-SCR plus main SCR system, both with and without an electric heater upstream of the LO-SCR. These catalysts were hydrothermally aged to simulate significant field use. Dual SCR dosing with newly developed controls played a critical role in achieving the proper split between the upstream LO-SCR and the downstream main SCR. Adding a next generation mixer for the downstream SCR proved essential in obtaining the final results. The optimal configuration required adding an electric heater to elevate the exhaust temperature at the LO-SCR for early cycle NOx reduction. The final results showed a 94.8% NOx reduction and 15.7% fuel savings on the composite NRTC.

McCarthy, James [Eaton Corporation]↗

A computational investigation of diesel and biodiesel combustion and NOx formation in a light-duty compression ignition engine

Diesel and biodiesel combustion in a multi-cylinder light duty diesel engine were simulated during a closed cycle (from IVC to EVO), using a commercial computational fluid dynamics (CFD) code, CONVERGE, coupled with detailed chemical kinetics. The computational domain was constructed based on engine geometry and compression ratio measurements. A skeletal n-heptane-based diesel mechanism developed by researchers at Chalmers University of Technology and a reduced biodiesel mechanism derived and validated by Luo and co-workers were applied to model the combustion chemistry. The biodiesel mechanism contains 89 species and 364 reactions and uses methyl decanoate, methyl-9- decenoate, and n-heptane as the surrogate fuel mixture. The Kelvin-Helmholtz and Rayleigh-Taylor (KH-RT) spray breakup model for diesel and biodiesel was calibrated to account for the differences in physical properties of the fuels which result in variations in atomization and spray development characteristics. The simulations were able to capture the experimentally observed pressure and apparent heat release rate trends for both the fuels over a range of engine loads (BMEPs from 2.5 to 10 bar) and fuel injection timings (from 0° BTDC to 10° BTDC), thus validating the overall modeling approach as well as the chemical kinetic models of diesel and biodiesel surrogates. Moreover, quantitative NOx predictions for diesel combustion and qualitative NOx predictions for biodiesel combustion were obtained with the CFD simulations and the in-cylinder temperature trends were correlated to the NOx trends.

Wang, Zihan↗

Investigation and Optimization of Biodiesel Chemistry for HCCI Combustion

Over the past 5 years, ORNL has run 95 diesel range fuels in homogene-ous charge compression ignition (HCCI), including 40 bio-diesels and associated diesel fuels in their blending. The bio-diesel blends varied in oxygen content, iodine number, cetane, boiling point distribution, chemical composition, and some contained nitrogen. All fuels were run in an HCCI engine at 1800 rpm, in the power range of 2.5 to 4.5 bar IMEP, using intake air heating for combustion phasing control, and at a compression ratio of 10.6. The engine response to fuel variables has been analyzed statistically. Generally, the engine responded well to fuels with lower nitrogen and oxygen, lower cetane, and lower aromatics. Because of the wide range of fuels combined in the model, it provides only a broad overview of the engine response. It is recommended that data be truncated and re-modeled to obtain finer resolution of engine response to particular fuel variables.

33 ADVANCED PROPULSION SYSTEMS↗

3-D Modeling of the CFR Engine for the Investigation of Knock on Natural Gas

Engine knock and misfire are barriers to pathways leading to higher efficiency natural gas (NG) engines, where the general tendency to knock is highly dependent on engine operating conditions and the fuel reactivity. The problem is further complicated by low emissions limits and the wide range of chemical reactivity in pipeline quality NG, making the understanding of fuel-engine interactions essential to achieving high efficiencies in spark-ignited NG engines. The present work highlights a three-dimensional computational fluid dynamics (CFD) model of the Cooperative Fuel Research (CFR) engine to investigate knock behavior when running on NG. Using a Converge CFD model of the CFR engine fuel-engine interactions that lead to knock with NG, including effects of fuel reactivity, engine operating parameters, and exhaust gas recirculation, are being investigated. A GT-Power model is used to estimate appropriate initial conditions in the Converge CFD model, including cylinder wall, piston, valves, and port surface temperatures as well as residual gas fraction. In order to validate the model, in-cylinder pressure data taken with a CFR engine is compared to model predictions while varying compression ratio, CA50, and BMEP.

Bestel, Diego↗

3-D Modeling off the CFR Engine for the Investigation of Knock on Natural Gas

Engine knock and misfire are barriers to pathways leading to high-efficiency Natural Gas (NG) engines. The general tendency to knock is highly dependent on engine operating conditions and the fuel reactivity. The problem is further complicated by low emissions limits and the wide range of chemical reactivity in pipeline quality NG (65< MN<95). In order to realize diesel-like efficiencies, spark-ignited NG engines must be designed to operate at high BMEP near knock limits over a wide range of fuel reactivity. This requires a deep understanding regarding combustion-engine interactions important in flame propagation and end-gas autoignition. The present work highlights a three-dimensional computational fluid dynamics (CFD) model of the Cooperative Fuel Research (CFR) engine to investigate knock behavior with NG. The CFR engine model is used to investigate fuel-engine interactions that lead to knock with NG, including effects of fuel reactivity, engine operating parameters, and exhaust gas recirculation (EGR). Cylinder wall, piston, valves, and port surface temperatures are estimated with a 1-D Three-Pressure Analysis (TPA) model. Model validation was performed by comparing model predictions with experimental data taken with a CFR engine over varying compression ratio, CA50, EGR fraction and BMEP.

Bestel, Diego↗

Development of a Physics-Based Combustion Model for Engine Knock Prediction

The objective of this project is to improve the prediction of engine knock by developing a new combustion modeling framework. Engine knock is a limiting factor to constrain the increase of fuel efficiency for spark ignition (SI) engines in most passenger cars. Efforts to increase fuel efficiency, increasing the compression ratio or downsizing, lead to the increase in the tendency of the knock occurrence. The knock is an undesired ignition of the end-gas, unburned fuel/air mixture ahead of the spark-ignited premixed flame, resulting in rapid in-cylinder pressure rises and engine damages. The combustion modeling framework developed in this project can consider turbulence-chemistry interactions during end-gas ignition, while using a reasonably detailed chemical mechanism developed for ignition and combustion reactions under engine relevant conditions, and the subtle characteristics of spark-ignited flame propagation. It is developed in the context of large eddy simulation (LES), which can capture stochastic in-cylinder processes. The developed model is incorporated into a commercial software for engine simulation, CONVERGE CFD, as a user defined function, and validated. Engine knock and knock-free experiments as well as direct numerical simulation (DNS) of end-gas ignition in homogeneous turbulence are performed to help model development and provide data sets for model validation. With further validation, the developed model is expected to advance the predictive capability for engine knock simulations and thus contribute to improving the fuel efficiency.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

3-D Modeling of the CFR Engine for the Investigation of Knock on Natural Gas

Abstract: Engine knock and misfire are barriers to pathways leading to higher efficiency natural gas (NG) engines, where the general tendency to knock is highly dependent on engine operating conditions and the fuel reactivity. The problem is further complicated by low emissions limits and the wide range of chemical reactivity in pipeline quality NG, making the understanding of fuel- engine interactions essential to achieving high efficiencies in spark-ignited NG engines. The present work highlights a three-dimensional computational fluid dynamics (CFD) model of the Cooperative Fuel Research (CFR) engine to investigate knock behavior when running on NG. Using a Converge CFD model of the CFR engine fuel-engine interactions that lead to knock with NG, including effects of fuel reactivity, engine operating parameters, and exhaust gas recirculation, are being investigated. A GT-Power model is used to estimate appropriate initial conditions in the Converge CFD model, including cylinder wall, piston, valves, and port surface temperatures as well as residual gas fraction. In order to validate the model, in-cylinder pressure data taken with a CFR engine is compared to model predictions while varying compression ratio, CA50, and BMEP.

CFR Engine, Converge CFD, knock, Natural Gas↗

MULTI-DIMENSIONAL MODELING OF THE CFR ENGINE FOR THE INVESTIGATION OF SI NATURAL GAS COMBUSTION AND CONTROLLED END-GAS AUTOIGNITION

Engine knock and misfire are barriers to pathways leading to high-efficiency Spark-Ignited (SI) Natural Gas engines. The general tendency to knock is highly dependent on engine operating conditions and the fuel reactivity. The problem is further complicated by low emission limits and the wide range of chemical reactivity in pipeline quality natural gas. Depending on the region and the source of the natural gas, its reactivity, described by its methane number (analogous to the octane number for liquid SI fuels) can span from 65 - 95. In order to realize diesel-like efficiencies, SI natural gas engines must be designed to operate at high BMEP near knock limits over a wide range of fuel reactivity. This requires a deep understanding regarding the combustion-engine interactions pertaining to flame propagation and end-gas autoignition (EGAI). However, EGAI, if controlled, provides an opportunity to increase SI natural gas engine efficiency by increasing combustion rate and the total burned fuel, mitigating the effects of the slow flame speeds of natural gas fuels which generally reduce BMEP and increase unburned hydrocarbon emissions. For this reason, in order to study EGAI phenomenon, the present work highlights multi-dimensional computational fluid dynamics (CFD) models of the Cooperative Fuel Research (CFR) engine. The CFR engine models are used to investigate fuel-engine interactions that lead to EGAI with natural gas, including effects of fuel reactivity, engine operating parameters, and exhaust gas recirculation (EGR). A Three-Pressure Analysis, performed with GT-Power, was used to estimate initial and boundary conditions for the three-dimensional CFD model. CONVERGE CFD v2.4 was used for the three-dimensional CFD modeling where the level set G-Equation model and SAGE detailed chemical kinetics solver were used. An assessment of the different modeling approaches is also provided to evaluate their limitations, advantages and disadvantages, and for which situations they are most applicable. Model validation was performed with experimental data taken with a CFR engine over varying compression ratio, CA50, EGR fraction, and IMEP and shows good agreement in Peak Cylinder Pressure (PCP), PCP crank angle, and the location of the 10%, 50%, and 90% mass fraction burned (CA10, CA50, and CA90, respectively). The models can predict the onset crank angle and pressure rise rate for light, medium, and heavy EGAI under a variety of fuel reactivities and engine operating conditions.

Bestel, Diego↗

The Impact of LPG Composition on Performance, Emissions, and Combustion Characteristics of a Pre-mixed Spark-Ignited CFR Engine

Research on alternative fuels has made significant progress as demands for cleaner and more efficient engine operation intensifies. Liquefied petroleum gas (LPG) can offer a potential alternative fuel route in the Diesel fuel dominated heavy-duty transportation sector due to its low cost, high anti-knock limit relative to gasoline, and reduced emission levels. In this work, experimental investigations are performed to study the effects of LPG compositions on performance, emissions, and combustion behavior of a spark-ignited (SI) cooperative fuel research (CFR) engine under stoichiometric conditions. Four LPG blends (chemically pure propane, a representative US blend, HD-5, and a representative European blend) representing the present LPG market are chosen. The impact of fuel composition is studied under different compression ratios (CR), ranging from 7:1 to 10:1 with one-unit increments, and at constant engine speed, intake manifold air pressure (IMAP) and 50% burn crank angle (CA50). The results show that fuel composition has minimal effect on engine efficiency over the CR range 7:1 to 10:1. Engine-out emissions are substantially affected by fuel compositions with the representative European blend indicating higher unburned hydrocarbon (UHC) emissions, particularly at higher CR. The representative US blend emits the lowest brake specific CO (bsCO) averaged over the tested CR range. With the increase of CR, end-gas autoignition intensifies for all blends and the representative European blend demonstrates the highest knock intensity of all tested blends, due to the presence of the more reactive fuel component, n-butane.

Fosudo, Toluwalase↗

Impact on Cycle Efficiency of Small CHP Plants from Increasing Firing Temperature Enabled by AM of Turbine Blades

Combined Heat and Power (CHP) systems are gaining popularity because of their potential for high overall thermodynamic efficiency and increased need for distributed power generation. Most CHP systems include a gas turbine for electricity generation and a heat recovery steam generator (HRSG) for steam generation. The steam can be used to power a steam turbine for additional electricity generation or to drive rotating equipment, for space heating, for absorption chillers, etc. A CHP cycle configuration is often driven by the ‘principal’ utility for the facility that it services; steam or electricity. In either case, performance improvements in the gas turbine have the potential to increase the steam and power output from the cycle, which is a direct result of improvements in the gas turbine efficiency and power output. One possible opportunity to improve an existing gas turbine’s performance is to increase the firing temperature with improved turbine cooling and increased compression ratio.<br>In this study, the impact on CHP cycle performance from increasing the turbine firing temperature by 100 °C and improving the turbine blade cooling for a 6-MW scale gas turbine is estimated using an analytical cooled gas turbine model and a steam cycle model. A sensitivity analysis was performed to understand the impact of increasing the internal cooling effectiveness, thermal barrier coating performance and blade material upgrades on gas turbine and CHP cycle efficiency. The impacts of turbine blade cooling improvements were studied for three common CHP cycle configurations identified from the literature. Various definitions for CHP cycle efficiency from the literature are used in the comparisons. The results showed that a 100 °C increase in firing temperature can increase the gas turbine efficiency by 1 percentage point without improving cooling effectiveness and add 2 additional percentage points in efficiency by using advanced turbine blades with higher internal cooling efficiency. Studied engine upgrades showed potential for increasing the CHP cycle efficiency by 3 percentage points while increasing the steam generation rate by 8%.<br>

Uysal, Selcuk Can↗

System and method for engine control with pressure reactive device to control combustion timing

The present disclosure relates to a system for controlling ignition of an intake charge directed into an internal combustion engine. The system may have a movable component operably associated with at least one of a piston of the engine or a combustion chamber of the engine. The movable component may be tuned to deflect in response to a predetermined pressure being reached in a cylinder in which the piston is housed. The movable component operates to deflect in response to the predetermined pressure being reached in the cylinder as the piston travels toward top dead center during its compression stroke, to change a compression ratio of the engine.

Killingsworth, Nicholas↗

Next Generation High Efficiency Boosted Engine Concept

This report summarizes a collaborative research project between Ford Motor Company, FEV North America, and Oak Ridge National Laboratory to develop a next-generation, high-efficiency, boosted spark-ignited engine. The goal was to achieve a 23% improvement in fuel economy and a 15% reduction in engine weight compared to a 2016 Ford F150. The team utilized advanced technologies including a high compression ratio, cooled exhaust gas recirculation (EGR), early intake valve closing, and a novel active pre-chamber ignition system. The final engine prototype met the fuel economy goal and demonstrated a 4.3% weight reduction, with further opportunities identified to reach the full 15% target.

Fuel economy↗

Gas turbine power plant with supersonic shock compression ramps

A gas turbine engine. The engine is based on the use of a gas turbine driven rotor having a compression ramp traveling at a local supersonic inlet velocity (based on the combination of inlet gas velocity and tangential speed of the ramp) which compresses inlet gas against a stationary sidewall. The supersonic compressor efficiently achieves high compression ratios while utilizing a compact, stabilized gasdynamic flow path. Operated at supersonic speeds, the inlet stabilizes an oblique/normal shock system in the gasdynamic flow path formed between the rim of the rotor, the strakes, and a stationary external housing. Part load efficiency is enhanced by use of a lean pre-mix system, a pre-swirl compressor, and a bypass stream to bleed a portion of the gas after passing through the pre-swirl compressor to the combustion gas outlet. Use of a stationary low NOx combustor provides excellent emissions results.

20 FOSSIL-FUELED POWER PLANTS↗