Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CIGS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Effects of copper excess and copper deficiency on the structural and electrical properties of bulk Cu{sub x}SnSe{sub 3} with x=1.6–2.2

Effects of the Cu variation on the morphological, structural, and electrical properties of bulk Cu{sub x}SnSe{sub 3} (CTSe) with x=1.6–2.2 have been investigated. Dense CTSe pellets with grains of 3–4 µm were obtained after sintering at 550 °C. All CTSe pellets showed a dominant p-type behavior. CTSe at x=2.0 with a hole concentration (n{sub p}) of 1.02×10{sup 18} cm{sup −3} and Hall mobility (μ) of 225 cm{sup 2}/V/s had a highest conductivity (σ) of 39 S/cm. CTSe at x=1.6 with n{sub p} of 5.0×10{sup 17} cm{sup −3} and of 11 cm{sup 2}/V/s had a lowest of 0.90 S/cm. The explanation, based upon vacancies and antisite defects, for the changes in electrical property with the Cu content is supported by the data from lattice parameter. The study in bulk properties of CTSe and its defects is helpful for selecting the suitable absorber composition to fabricate thin film solar cells. - Graphical abstract: Cu{sub 2}SnSe{sub 3} is an absorber candidate for solar cells. The Cu stoichiometry on electrical properties, which is important for CIGS and CZTS, is investigated and the Cu-deficiency composition is recommended. - Highlights: • Cu{sub x}SnSe{sub 3} (CTSe) bulks with 1.6≤x≤2.2 were prepared by reactive sintering. • Cu{sub 2}SnSe{sub 3} with n{sub p} of 1.02×10{sup 18} cm{sup −3} and μ of 225 cm{sup 2}/V/s had highest σ of 39 S/cm. • Cu{sub 1.6}SnSe{sub 3} with n{sub p}=5.0×10{sup 17} cm{sup −3} and μ=11 cm{sup 2}/V/s had lowest σ=0.90 S/cm. • Lower n{sub p} at CTSe at x=1.6 is related to the formation of the Sn-to-Cu defect. • The drop in n{sub p} for CTSe at x=2.2 indicates V{sub Sn}{sup 4−} dominates over Cu{sub Sn}{sup 3−} defect.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Combinatorial sputtering of Ga-doped (Zn,Mg)O for contact applications in solar cells

In this study, the development of tunable contact materials based on environmentally friendly chemical elements using scalable deposition approaches is necessary for existing and emerging solar energy conversion technologies. In this paper, the properties of ZnO alloyed with magnesium (Mg), and doped with gallium (Ga) are studied using combinatorial thin film experiments. As a result of these studies, the optical band gap of the sputtered Zn 1-x Mg x O thin films was determined to vary from 3.3 to 3.6 eV for a compositional spread of Mg content in the 0.04 < x < 0.17 range. Depending on whether or not Ga dopants were added, the electron concentrations were on the order of 10 17 cm -3 or 10 20 cm -3 , respectively. Based on these results and on the Kelvin Probe work function measurements, a band diagram was derived using basic semiconductor physics equations. The quantitative determination of how the energy levels of Ga-doped (Zn, Mg)O thin films change as a function of Mg composition presented here, will facilitate their use as optimized contact layers for both Cu 2 ZnSnS 4 (CZTS), Cu(In, Ga)Se 2 (CIGS) and other solar cell absorbers.

14 SOLAR ENERGY↗

Selection of optimal wavelengths for optical soiling modelling and detection in photovoltaic modules

Soiling impacts the photovoltaic (PV) module performance by decreasing the amount of light reaching the photovoltaic cells and by changing their external spectral response. Currently, the soiling monitoring market is moving toward optical sensors that measure transmittance or reflectance, rather than directly measuring the impact of soiling on the performance of photovoltaic modules. These sensors, which use a single optical measurement, are not able to correct the soiling losses that depend on the solar irradiance spectra and on the spectral response of the monitored PV material. This work investigates methods that can improve the optical detection of soiling by extracting the full soiling spectrum profiles using only two or three monochromatic measurements. Spectral transmittance data, measured with a spectrophotometer and collected during a 46-week experimental soiling study carried out in Jaén, Spain, was analysed in this work. The use of a spectral profile for the hemispherical transmittance of soiled PV glass is found to significantly improve the soiling detection, returning the lowest errors independently of the PV materials and irradiance conditions. In addition, this work shows that it is also possible to select the measurement wavelengths to minimize the soiling loss detection error depending on the monitored PV semiconductor material (silicon, CdTe, a-Si, CIGS and a representative perovskite). The approaches discussed in this work are also found to be more robust to potential measurement errors compared to single wavelength measurement techniques.

14 SOLAR ENERGY↗

Radiation Stability of Mixed Tin-Lead Halide Perovskites: Implications for Space Applications

Mixed organic-inorganic halide perovskite solar cells (PSCs) have received considerable attention in recent years for their impressive solar to electrical power efficiency gains and potentially lower material and processing costs for optoelectronic applications. In addition to terrestrial applications, PSCs are of interest to the space power markets for their low cost, low weight, adaptability to flexible architectures, and tolerance to high energy particle irradiation (mainly protons and electrons). Here we investigate the properties of mixed formamidinium-methylammonium tin-lead iodide (FASn)0.6(MAPb)0.4I3 perovskites which lower the lead content as well as the bandgap, making them attractive for the low bandgap absorber material in tandem PSCs. Through current density-voltage (JV) characterization at lower temperatures, majority carrier transport is hindered and a barrier to photogenerated carrier extraction is evident. This is attributed to the thermally induced change of the bandgap of the absorber layer relative to the energy selective contacts in the device. We find that although the architecture used here hinders the performance at temperatures below 225 K, the tolerance to high energy (3.7 MeV) protons is impressive, considerably out-performing commercially available thin-film CIGS. These results suggest further improvements to structural and interface stability as well as lightweight encapsulation could lead to all perovskite flexible tandem arrays deployed for power generation on missions to low Earth orbit, the moon, Mars, and beyond.

perovskite solar cells↗

Metabolites of Tobacco- and E-Cigarette-Related Nitrosamines Can Drive Cu 2+ -Mediated DNA Oxidation

Nitrosamine metabolites resulting from cigarette smoking and E-cigarette (E-cig) vaping cause DNA damage that can lead to genotoxicity. While DNA adducts of metabolites of nitrosamines 4-(methylnitrosamino)-1-(3-pyridyl)-1-butanone (NNK) and N-nitrosonornicotine (NNN) are well-known tobacco-related cancer biomarkers, only a few studies implicate NNN and NNK in DNA oxidation in humans. NNK and NNN were found in the urine of E-cigarette users who never smoked cigarettes. This paper proposes the first chemical pathways of DNA oxidation driven by NNK and NNN metabolites in redox reactions with Cu 2+ and NADPH leading to reactive oxygen species (ROS). A microfluidic array with thin films of DNA and metabolic enzymes that make metabolites of NNN and NNK in the presence of Cu 2+ and NADPH was used to estimate relative rates of DNA oxidation. Detection by electrochemiluminescence (ECL) employed a new ECL dye [Os(tpy-benz-COOH) 2 ] 2+ that is selective for and sensitive to the primary DNA oxidation product 8-oxo-7,8-dihydro-2-deoxyguanosine (8-oxodG) in DNA. Enzyme–DNA films on magnetic beads were used to produce nitrosamine metabolites that enter ROS-forming redox cycles with Cu 2+ and NADPH, and liquid chromatography–mass spectrometry (LC–MS) was used to quantify 8-oxodG and identify metabolites. ROS were detected by optical sensors. Metabolites of NNK and NNN + Cu 2+ + NADPH generated relatively high rates of DNA oxidation. Lung is the exposure route in smoking and vaping, human lung tissue contains Cu 2+ and NADPH, and lung microsomal enzymes gave the highest rates of DNA oxidation in this study. Furthermore, E-cigarette vapor contains 6-fold more copper than that in cigarette smoke, which could exacerbate DNA oxidation.

59 BASIC BIOLOGICAL SCIENCES↗

Improved H 2 Evolution in Quaternary SCIGS Chalcopyrite Semiconductors

In a search for improved photocathode materials for fuel-producing photoelectrochemical cells, quaternary Ag x Cu 1-x Ga y In 1-y S 2 (0 ≤ x ≤ 1.0, 0 ≤ y ≤ 1.0) p-type, chalcopyrite semiconductors (SCIGS) were prepared and tested for photochemical hydrogen evolution. The study reported here is based on the preparation of bulk phases of the quaternary system. In contrast to thin-film studies of this system, this approach enables enhanced control of the materials' chemical, structural, and electronic properties. Compared to ternary CIGS electrode materials, the quaternary SCIGS materials provide improved photoelectrochemical and electrocatalytic properties. The quaternary system allows for adjustment of the band structures and photocatalytic abilities to a finer degree than is possible in the Ag x Cu 1-x GaS 2 or Ag x Cu 1-x InS 2 ternaries, and several of the quaternary Ag x Cu 1-x Ga y In 1-y S 2 compositions are found to show better water-splitting capability than the ternaries, even when a platinum co-catalyst is present in the ternary systems. Our work on quaternary compounds has led to finding unexpected optoelectric properties in ternary compounds of composition Ag x Cu 1-x GaS 2 . Specifically, a "V-shaped" plot of semiconductor composition versus band gap is observed, which is not easily correlated with the observed variation in semiconductor structure. Even more interesting is the observation that the silver-rich branch of this "V" produces obviously higher H 2 evolution rates than observed with the copper-rich branch.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Model for Characterization and Optimization of Spectrally Selective Structures to Reduce the Operating Temperature and Improve the Energy Yield of Photovoltaic Modules

Many existing commercially manufactured photovoltaic modules include a cover layer of glass, commonly coated with a single layer antireflection coating (ARC) to reduce reflection losses. As many common photovoltaic cells, including c-Si, CdTe, and CIGS, decrease in efficiency with increasing temperature, a more effective coating would increase reflection of sub-bandgap light while still acting as an antireflection coating for higher energy photons. The sub-bandgap reflection would reduce parasitic sub-bandgap absorption and therefore reduce operating temperature. This reduction under realistic outdoor conditions would lead to an increase in annual energy yield of a photovoltaic module beyond what is achieved by a single layer ARC. However, calculating the actual increase in energy yield provided by this approach is difficult without using time-consuming simulation. Here, we present a time-independent matrix model which can quickly determine the percentage change in annual energy yield of a module with a spectrally selective mirror by comparison to a baseline module with no mirror. The energy benefit is decomposed into a thermal component from temperature reduction and an optical component from increased transmission of light above the bandgap and therefore increased current generation. Time-independent matrix model calculations are based on real irradiance conditions that vary with geographic location and module tilt angle. The absolute predicted values of energy yield improvement from the model are within 0.1% of those obtained from combined ray-tracing and time-dependent finite-element simulations and compute 1000x faster. Uncertainty in the model result is primarily due to effects of wind speed on module temperature. Optimization of the model result produces a 13-layer and a 20-layer mirror, which increase annual module energy yield by up to 4.0% compared to a module without the mirror, varying depending on the module location and tilt angle. Finally, we analyze how spectrally selective mirrors affect the loss pathways of the photovoltaic module.

14 SOLAR ENERGY↗

Macroscopic Nonuniformities in Metal Grids Formed by Cracked Film Lithography Result in 19.3% Efficient Solar Cells

Cracked film lithography (CFL) is an emerging method for patterning transparent conductive metal grids. CFL can be vacuum- and Ag-free, and it forms more durable grids than nanowire approaches. In spite of CFL’s promising transmittance/grid sheet resistance/wire spacing tradeoffs, previous solar cell demonstrations have had relatively low performance. This work introduced macroscopic nonuniformities in the grids to improve the short-circuit current density/fill factor tradeoff in small area Cu(In,Ga)Se2 cells. Furthermore, the performance of optimized baseline grids was matched by CFL grids with microscopic openings and macroscopic patterns, culminating in a 19.3%-efficient cell. Simulations show that uniform CFL grids are enhanced by patterning because it leads to better balance among shadowing, grid resistance and transparent conductive oxide resistance losses. Thin-film module efficiency calculations were performed to highlight the performance gains that metal grids can enable by eliminating the transparent conductive oxide losses and widening monoliths. Adding the patterned CFL grids demonstrated in this work to CIGS modules is predicted to reach 0.7% higher efficiency (absolute) than screen-printed grids.

14 SOLAR ENERGY↗

Grazing Incidence Cross-Sectioning of Thin-Film Solar Cells via Cryogenic Focused Ion Beam: A Case Study on CIGSe

Cryogenic focused ion beam (Cryo-FIB) milling at near-grazing angles is employed to fabricate cross-sections on thin Cu(In,Ga)Se2 with >8x expansion in thickness. Kelvin probe force microscopy (KPFM) on sloped cross sections showed reduction in grain boundaries potential deeper into the film. Cryo Fib-KPFM enabled the first determination of the electronic structure of the Mo/CIGSe back contact, where a sub 100 nm thick MoSey assists hole extraction due to 45 meV higher work function. This demonstrates that CryoFIB-KPFM combination can reveal new targets of opportunity for improvement in thin-films photovoltaics such as high-work-function contacts to facilitate hole extraction through the back interface of CIGS.

14 SOLAR ENERGY↗

Molecular Coatings Improve the Selectivity and Durability of CO 2 Reduction Chalcogenide Photocathodes

The quest for solar-driven conversion of carbon dioxide to chemicals and fuels hinges upon the identification of an efficient, durable, and selective photocathode. Chalcogenide p-type semiconductors exemplified by chalcopyrite Cu(In,Ga)Se 2 (CIGS) have been effectively deployed as photocathodes. However, selectivity toward CO 2 reduction and durability of the commonly used CdS adlayer remain primary challenges. Here, we demonstrate that for the wide band gap CuGa 3 Se 5 chalcopyrite absorber these challenges are well addressed by an organic coating generated in situ from an N,N'-(1,4-phenylene)bispyridinium ditriflate salt in the electrolyte. The molecular additive provides a 30-fold increase in selectivity toward CO2R products compared to the unmodified system and lowers Cd corrosion at least 10-fold. This dual functionality highlights the promise of hybrid solid-state-molecular photocathodes for enabling durable and efficient solar fuel systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Complexation Chemistry in N,N -Dimethylformamide-Based Molecular Inks for Chalcogenide Semiconductors and Photovoltaic Devices

Molecular inks based on dimethyl sulfoxide, thiourea, and metal salts may be used to form high optoelectronic quality semiconductors and have led to high power conversion efficiencies for solution-processed photovoltaic devices for Cu 2 ZnSn(S,Se) 4 (CZTS), Cu 2 Zn(Ge,Sn)(S,Se) 4 (CZGTS), CuIn(S,Se) 2 (CIS) and Cu(In,Ga)(S,Se) 2 (CIGS). However, several metal species of interest including Ag(I), In(III), Ge(II), and Ge(IV) have either low solubility (requiring dilute inks) or lead to precipitation or gelation. Here, we demonstrate that the combination of N,N -Dimethylformamide (DMF) and thiourea (TU) has the remarkable ability to form intermediate-stability acid-base complexes with a wide number of metal chloride Lewis acids (CuCl, AgCl, ZnCl 2 , InCl 3 , GaCl 3 , SnCl 4 , GeCl 4 , and SeCl 4 ) to form high-concentration stable molecular inks. Using calorimetry, Raman spectroscopy, and solubility experiments, we reveal the important role of chloride transfer and thiourea to stabilize metal cations in DMF. Methylation of thiourea is used to vary the strength of the Lewis basicity and demonstrate that the strength of the thiourea:metal chloride complex formed after DMF evaporation is critical to prevent volatilization of metal containing species. Further, we formulated a sulfur-free molecular ink which was used to deposit photoluminescent, crystalline CuInSe 2 without selenization . Finally, we demonstrate the ability of the DMF-TU molecular ink chemistry to lead to high photovoltaic power conversion efficiencies and high open-circuit voltages for solution-processed CIS and CZGTS with PCE’s of 13.4% and 11.0% and V oc /V oc,SQ of 67% and 63%, respectively.

Clark, James A.↗

Computational Seismology Workshop Trains Early-Career Scientists

The Computational Infrastructure for Geodynamics (CIG), in collaboration with Lawrence Livermore National Laboratory (LLNL), held a workshop last year that focused on computational seismology. The workshop provided training in seismic waveform processing, visualization, and high-performance computing (HPC) waveform simulation. Fifty-five predominantly early-career participants—graduate students and postdocs—from the United States and 16 other countries attended. The workshop was the first of its kind to feature full access to HPC resources for research-grade example problems.

58 GEOSCIENCES↗

Increasing markets and decreasing package weight for high-specific-power photovoltaics

We report that thin-film and emerging technologies in photovoltaics (PV) offer advantages for lightweight, flexible power over the rigid silicon panels that dominate the present market. One important advantage is high specific power (the power-to-weight ratio). Here we consider niche market size, price points and value propositions that can provide a path for new PV market entrants. Examining the cost-production experience curves of Si, CdTe and CIGS PV suggests that a minimum market size of US$0.2-1 billion is required to incubate a new market entrant. Several markets requiring high specific power meet this threshold. We assess the critical role of the substrate, packaging and interconnects and provide a quantitative assessment of pathways to maximize specific power. With all requisite components included, along with requirements for safety and reliability, we estimate a lower bound for a durable lightweight module at about 300-500 g m -2 . Lastly, pairing this bound with a 15%-efficiency thin-film or 35%-efficiency III-V module would yield specific powers up to 500 W kg -1 or 1,167 W kg -1 , respectively.

14 SOLAR ENERGY↗

Prospects for metal halide perovskite-based tandem solar cells

Over the past decade, metal halide perovskite photovoltaics have been a major focus of research, with single-junction perovskite solar cells evolving from an initial power conversion efficiency of 3.8% to reach 25.5%. The broad bandgap tunability of perovskites makes them versatile candidates as the subcell in a tandem photovoltaics architecture. Stacking photovoltaic absorbers with cascaded bandgaps in a multi-junction device can potentially overcome the Shockley–Queisser efficiency limit of 33.7% for single-junction solar cells. There is now intense activity in developing tandem solar cells that pair perovskite with either itself or with a variety of mature photovoltaic technologies such as silicon and Cu(In,Ga)(S,Se) 2 (CIGS). In this review, we survey recent advances in the field and discuss its outlook.

14 SOLAR ENERGY↗

Optically induced metastability in Cu(In,Ga)Se 2

Cu(In,Ga)Se 2 (CIGS) is presently the most efficient thin-film photovoltaic technology with efficiencies exceeding 22%. An important factor impacting the efficiency is metastability, where material changes occur over timescales of up to weeks during light exposure. A previously proposed (V Se -V Cu ) divacancy model presents a widely accepted explanation. We present experimental evidence for the optically induced metastability transition and expand the divacancy model with first-principles calculations. Using photoluminescence excitation spectroscopy, we identify a sub-bandgap optical transition that severely deteriorates the carrier lifetime. This is in accordance with the expanded divacancy model, which predicts that states below the conduction band are responsible for the metastability change. We determine the density–capture cross-section product of the induced lifetime-limiting states and evaluate their impact on device performance. The experimental and theoretical findings presented can allow assessment of metastability characteristics of leading thin-film photovoltaic technologies.

14 SOLAR ENERGY↗

Overcoming Carrier Concentration Limits in Polycrystalline CdTe Thin Films with In Situ Doping

Abstract Thin film materials for photovoltaics such as cadmium telluride (CdTe), copper-indium diselenide-based chalcopyrites (CIGS), and lead iodide-based perovskites offer the potential of lower solar module capital costs and improved performance to microcrystalline silicon. However, for decades understanding and controlling hole and electron concentration in these polycrystalline films has been extremely challenging and limiting. Ionic bonding between constituent atoms often leads to tenacious intrinsic compensating defect chemistries that are difficult to control. Device modeling indicates that increasing CdTe hole density while retaining carrier lifetimes of several nanoseconds can increase solar cell efficiency to 25%. This paper describes in-situ Sb, As, and P doping and post-growth annealing that increases hole density from historic 10 14 limits to 10 16 –10 17 cm −3 levels without compromising lifetime in thin polycrystalline CdTe films, which opens paths to advance solar performance and achieve costs below conventional electricity sources.

14 SOLAR ENERGY↗

Multimodal characterization of solution-processed Cu3SbS4 absorbers for thin film solar cells

The most efficient inorganic thin film chalcogenide-based solar cells use CdTe or CuInGaSe2 (CIGS) as absorber layers, which rely on toxic (Cd) and/or scarce elements (In, Te). The desire for more sustainable solar cells has led to the development of Earth abundant and non-hazardous chalcogenide absorbers. Cu3SbS4 (famatinite) is a promising Earth abundant p-type semiconductor that has a low direct band gap (0.9–1.05 eV), is a superabsorber (absorption coefficient 104–105 cm1), and has potential in low-cost, thin-film solar cells. Although these properties make the Cu3SbS4 phase stand out as a promising material for photovoltaics, to date Cu3SbS4 solar cells have only achieved low efficiencies. In this study, we demonstrate a method for synthesizing Cu3SbS4 nanocrystals and formation of thin-films by coating nanocrystal precursors onto substrates. Optical, structural, and chemical state characterization were performed before and after thermal processing of the Cu3SbS4 films. A detailed experimental analysis of the bulk and surfaces of the Cu3SbS4 absorber films indicate that phase stability and preferential copper oxidation at the surface may limit device performance for Cu3SbS4 based solar cells. These findings may provide significant insight on how to improve Cu3SbS4 based solar cell performance by controlling processing conditions. This research was funded by the United States National Science Foundation – Scalable Nanomanufacturing program (Grant CBET-1449383). A portion of this research was performed at the Northwest Nanotechnology Infrastructure, a member of the National Nanotechnology Coordinated Infrastructure, which is supported by the National Science Foundation (Grant ECCS- 1542101). The acquisition of the OSU Titan TEM was supported by the National Science Foundation via the Major Research Instrumentation (MRI) program under Grant No. 1040588, the Murdock Charitable Trust, and the Oregon Nanoscience and Microtechnologies Institute (ONAMI). XANES spectra were obtained through an approved program user proposal at the Advanced Light Source, which is a DOE Office of Science User Facility under contract no. DE-AC02-05CH11231. The ALS approved program user proposal beam time was obtained through the chemical imaging initiative, an LDRD program at PNNL. We acknowledge Trey Diulus and Dr Igor Lyubinetsky for their assistance with the XPS experiments.

Albuquerque, Gustavo H.↗