Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Additive Manufacturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Microstructural evolution and mechanical properties of maraging steel produced by wire + arc additive manufacture process

Highlights: • Wire + arc additive manufacture (WAAM) was applied to produce maraging steel structures. • Microstructure evolution of WAAM alloy was characterized and correlated with the layer-by-layer building manner. • Mechanical properties of WAAM alloy were tested and correlated with the aging response of WAAM microstructure. • Retained austenite content was measured and correlated with the tensile strength loss. - Abstract: Wire + arc additive manufacture is developed for producing large-scale metallic components. In this paper, maraging steel parts were produced, and the microstructure and mechanical properties were investigated. The microhardness and tensile strength of the as deposited alloy reduced from the bottom to the top due to the transient thermal cycling, which resulted in partial aging and non-uniform formation of intermetallic compounds along the building direction. Solutionizing, followed by 3 h aging, significantly reduced the microstructural heterogeneity and increased the mechanical properties by 24.7% through the formation of large amounts of finely distributed precipitates. The as deposited alloy possessed superior strength to the wrought alloy in solutionized condition but inferior to the later in aged condition, which was attributed to the less pronounced aging response of the low-angle columnar grains characterized microstructure and the presence of retained and reverted austenite.

36 MATERIALS SCIENCE↗

Low-Field Alignment of Anisotropic Bonded Magnets for Additive Manufacturing of Permanent Magnet Motors

Additive manufacturing techniques for fabricating bonded magnets have the potential to reduce manufacturing cost and time-to-market of products and address the criticality of rare-earth elements (REEs), which is a concern for economic design of dependent applications such as permanent magnet machines. We investigated the magnetic alignment of anisotropic bonded magnet material comprising 65 vol.% Nd-Fe-B in nylon-12 produced by extrusion in a 20-W brushless direct current surface permanent magnet motor for submersible water pump application using finite element analysis. The results predict that sufficient alignment for this application could be obtained at low alignment fields (μoH ≤ 1 T) with a reduction in the volume of critical materials by up to 40% compared with isotropic permanent magnets. Furthermore, this demonstrates the economic feasibility of incorporating a magnetic alignment field source into additive manufacturing systems for bonded magnets, and the potential of aligned anisotropic bonded magnets to address REE criticality.

36 MATERIALS SCIENCE↗

In-situ high-speed X-ray imaging of piezo-driven directed energy deposition additive manufacturing

Powder-blown laser additive manufacturing adds flexibility, in terms of locally varying powder materials, to the ability of building components with complex geometry. Although the process is promising, porosity is common in a built component, hence decreasing fatigue life and mechanical strength. The understanding of the physical phenomena during the interaction of a laser beam and powder-blown deposition is limited and requires in-situ monitoring to capture the influences of process parameters on powder flow, absorptivity of laser energy into the substrate, melt pool dynamics and porosity formation. This study introduces a piezo-driven powder deposition system that allows for imaging of individual powder particles that flow into a scanning melt pool. As a result, in-situ high-speed X-ray imaging of the powder-blown additive manufacturing process of Ti-6Al-4V powder particles is the first of its kind and reveals how laser-matter interaction influences powder flow and porosity formation.

42 ENGINEERING↗

Additive manufacturing of multi-directional preforms for composites: opportunities and challenges

Current additive manufacturing methods present the potential to construct net-shape structures with complicated architectures, thus eliminating the need for multi-step processing and fasteners/joints. Combined with these features is the ability to ascribe material properties at the sub-millimeter scale, inspiring multi-material, functionally graded designs. These features make additive manufacturing an attractive option for composite materials development. In an effort to extend this family of technologies beyond nano- and micro-composites, we explore the additive manufacture of multi-directional composite preforms. This exercise has served to highlight the aspects of additive manufacturing critical to composite and general materials processing, as well as to demonstrate the high fidelity between modeled and additively manufactured structures. Within the scope of composites development, we review the state-of-the-art and discuss challenges facing the broad adoption of additive manufacturing for directionally reinforced composites processing.

36 MATERIALS SCIENCE↗

Adaptive wavelet compression of large additive manufacturing experimental and simulation datasets

New manufacturing technologies such as additive manufacturing require research and development to minimize the uncertainties in the produced parts. The research involves experimental measurements and large simulations, which result in huge quantities of data to store and analyze. We address this challenge by alleviating the data storage requirements using lossy data compression. We select wavelet bases as the mathematical tool for compression. Unlike images, additive manufacturing data is often represented on irregular geometries and unstructured meshes. Thus, we use Alpert tree-wavelets as bases for our data compression method. We first analyze different basis functions for the wavelets and find the one that results in maximal compression and miminal error in the reconstructed data. We then devise a new adaptive thresholding method that is data-agnostic and allows a priori estimation of the reconstruction error. Finally, we propose metrics to quantify the global and local errors in the reconstructed data. One of the error metrics addresses the preservation of physical constraints in reconstructed data fields, such as divergence-free stress field in structural simulations. While our compression and decompression method is general, we apply it to both experimental and computational data obtained from measurements and thermal/structural modeling of the sintering of a hollow cylinder from metal powders using a Laser Engineered Net Shape process. The results show that monomials achieve optimal compression performance when used as wavelet bases. The new thresholding method results in compression ratios that are two to seven times larger than the ones obtained with commonly used thresholds. Overall, adaptive Alpert tree-wavelets can achieve compression ratios between one and three orders of magnitude depending on the features in the data that are required to preserve. Furthermore, these results show that Alpert tree-wavelet compression is a viable and promising technique to reduce the size of large data structures found in both experiments and simulations.

42 ENGINEERING↗

Additive Manufacturing of Thermal Energy Storage Composites with Microencapsulated Phase Change Materials Supported in a Multi-Polymer Matrix

Advanced manufacturing techniques, such as additive manufacturing (AM), that can directly integrate phase change materials (PCMs) have garnered interest in recent years due to their potential for development of highly efficient thermal energy storage architectures. Complex, high surface area geometries embedded with PCMs that are only feasible with AM can improve thermal management with reduced material waste. Our work focuses on developing composite filaments with microencapsulated phase change materials (MEPCM) bound within a single or dual polymer matrix that can be processed through standard filament extruders and additively manufactured using off-the-shelf 3D printers. Polymer powders, rather than polymer pellets, were key to homogenously mixed filaments achieving high MEPCM loadings with no deterioration in thermal energy storage (TES) capability during extrusion. Composite filaments contain upwards of 60 wt% MEPCM and were printed without loss in feature resolution, print speed, or layer adhesion. Storage enthalpies of printed composites range from 100 - 130 kJ/kg, which were within 5% of the theoretical enthalpy based on weight fraction of MEPCM and maintained enthalpies within 1% over 500 thermal cycles. We can reliably manufacture low density, high surface area structures like 15% gyroid infill, along with dense, compact pucks at a 100% concentric infill. Prints were also scalable to a 900 cm3 honeycomb infill heat exchanger model that has an estimated energy storage capacity of 9 Wh.

3D printing↗

Integration of sensors through additive manufacturing leading to increased efficiencies of gas turbines for power generation and propulsion

To realize the full capability of additively manufactured components in complex energy systems, it is imperative to minimize early component failures during development phases and during operation. Traditional field feedback timelines and offline inspection protocols significantly reduce the design-manufacturing iteration times. To address this specific question, the project developed and demonstrated a method for the integration of sensors into complex components through additive manufacturing. The team used gas turbine engines as a platform, which meets the need of both power generation and propulsion and offer opportunities for cost reductions and efficiency increases. The innovation of this intelligent integration of sensors into complex components uniquely customized to address questions of integrity and durability for additively manufactured components. With real-time sensing data from additively manufactured components, turbine manufacturers will realize higher efficiencies, reduced component failures, and a 30-50% acceleration in product deployment of high efficiency gas turbine components due to a faster reduction in component risk assessment under actual operating conditions. This is a transformative shift towards a data-driven design and qualification of additively manufactured gas turbine components. To directly integrate sensors into additively manufactured components with all the complexities of actual hardware, powder bed fusion (direct metal laser sintering) and laser metal deposition technologies was developed. Validation took take place in two university laboratories both of which contain actual engine hardware and closely simulate a gas turbine prior to demonstrating the technology in a turbine development test. Indeed, two major technologies from this research cold impact turbine systems in the near future: (1) higher efficiency materials and designs enabled by additive manufacturing with 50% faster design to manufacturing cycle time, to enable faster time-to-market targets; and (2) integration of sensors into additively manufactured components enabling broad health and condition based prognostics for faster component and engine risk reduction.

33 ADVANCED PROPULSION SYSTEMS↗

Defect and satellite characteristics of additive manufacturing metal powders

Metal additive manufacturing (AM) requires high-quality metal powders to three-dimensionally (3D) print metallic components with complex and customizable geometries. The lack of quantification of AM metal powders creates quality control challenges for 3D printed components, increases the uncertainty of printing reliability and net cost of inspected and certified printed components, and reduces the recyclability of used powders. However, critical characteristics of AM metal powders that are decisive factors for the 3D printing process, such as internal porosity, contamination, and satellite feature, remain ambiguous. In this work, we developed a novel approach to 3D quantify key characteristics of AM metal powders down to individual particles by using high-resolution synchrotron x-ray computed tomography. Empowered by the penetrative capability of high-energy x-ray, internal porosity and contamination within as-atomized metal powders from high-entropy alloys to nickel-based superalloys were evaluated. Additionally, the newly-developed dispersion method enables the homogeneous separation of individual particles, and consequently, results in the implementation of 3D particle shape analysis. To resolve a major challenge of identification and quantification of satellite-feature particles in as-atomized AM metal powders, the satellite features were quantitated by modeling and analyzing the shape parameter of local thickness variance. Furthermore, the 3D analytical methods of particle assessment in this study can be applied to other materials systems like rock, food, and pharmaceutical particles, and provide insights for process optimization across powder metallurgy, concrete, food and pharmaceutical manufacturing, and AM industries.

36 MATERIALS SCIENCE↗

A study of internal structure in components made by additive manufacturing process using 3 D X-ray tomography

Additive manufacturing methods are gaining increasing popularity for rapidly and efficiently manufacturing parts and components in the industrial context, as well as for domestic applications. However, except when used for prototyping or rapid visualization of components, industries are concerned with the load carrying capacity and strength achievable by additive manufactured parts. In this paper, the wire-arc additive manufacturing (AM) process based on gas tungsten arc welding (GTAW) has been examined for the internal structure and constitution of components generated by the process. High-resolution 3D X-ray tomography is used to gain cut-views through wedge-shaped parts created using this GTAW additive manufacturing process with titanium alloy materials. In this work, two different control conditions for the GTAW process are considered. The studies reveal clusters of porosities, located in periodic spatial intervals along the sample cross-section. Such internal defects can have a detrimental effect on the strength of the resulting AM components, as shown in destructive testing studies. Closer examination of this phenomenon shows that defect clusters are preferentially located at GTAW traversal path intervals. These results highlight the strong need for enhanced control of process parameters in ensuring components with minimal defects and higher strength.

36 MATERIALS SCIENCE↗

Increasing Interlaminar Strength in Large Scale Additive Manufacturing

Interlaminar strength of extrusion-based additively manufactured parts is known to be weaker than the strength seen in the printed directions (X and Y). With Big Area Additive Manufacturing (BAAM), large parts lead to long layer times that are prone to splitting, sometimes referred to as delamination, between the layers. Fiber filled materials, such as carbon fiber reinforced ABS, are used to counter-act the effects of thermal expansion, but the fibers stay in-plane meaning that no fibers span from layer to layer, which helps counteract the weak interlaminar strength that causes splitting. A solution to this is a patent pending approach known as “z-pinning”. The process involves strategically positioning voids across multiple layers that will be backfilled with hot extrudate. This paper will explore the benefits and results of using “z-pinning” in large scale additive manufacturing.

Roschli, Alex↗

A novel method for production of spherical Ti-6Al-4V powder for additive manufacturing

We report a novel method was developed to produce spherical Ti-6Al-4V powder for advanced near-net-shape manufacturing processes including additive manufacturing and powder injection molding. The new process synergistically integrates a few common low-cost processing techniques including granulation, sintering, and de-oxygenation to produce spherical Ti alloy powders without relying on costly melting and atomizing techniques. This new granulation-sintering-deoxygenation (GSD) process can use low-cost source powders such as scrap Ti as the raw material. The spherical Ti-6Al-4V powder produced using this process has controlled particle size distribution and low oxygen content (< 0.15%), which meet the Aerospace Material Specification (AMS-4998) for spherical Ti-6Al-4V powder.

42 ENGINEERING↗

Wire Arc Additive Manufacturing

Project highlight. This project designs and implements a new additive manufacturing capability at Savannah River National Laboratory. Wire Arc Additive Manufacturing is an Advanced Manufacturing technology that enables materials and energy savings by producing materials that are in near net shapes to minimize material losses compared to conventional forging and machining techniques. Wire arc additive manufacturing is an evolving technology that can be used to fabricate large components with significantly less materials waste than conventional processing. This project includes an engineering model, an aspect that is largely overlooked in the Additive Manufacturing modeling work where the emphasis has been on mechanistic and microscopic modeling, to estimate the residual stresses and distortions. The Abaqus Weld Interface software coupled with user subroutines in Fortran enable the local cooling rates to be estimated to provide a coarse scale model for the secondary dendrite arm spacing, a parameter useful to estimate mechanical properties.

36 MATERIALS SCIENCE↗

Corrosion testing needs and considerations for additively manufactured materials in nuclear reactors

Metal additive manufacturing holds significant promise as an enabling technology for the 21st century nuclear energy industry. Metal additive manufacturing (MAM) can allow the fabrication of novel materials and innovative component designs that are not achievable through conventional manufacturing. Due to its very different fabrication methods, as-fabricated MAM components are characteristically different from conventionally manufactured components. MAM materials exhibit very different microstructures from conventional cast or wrought materials. For example, austenitic stainless steels fabricated by laser powder bed fusion exhibit columnar grain structures, dislocation cell structures, and melt pool fingerprints. In addition, MAM fabrication may result in defects such as porosity, incomplete processing of the feedstock (e.g., lack of fusion in melt-based methods), and oxide inclusions. Heat treatments may further evolve the microstructure, microsegregation, and stresses within the component. Furthermore, MAM components have a rough surface with feature sizes on the order of the feedstock material, as opposed to smooth surfaces resulting from conventional machining and forming operations. As a result, the corrosion behavior of MAM components will likely be significantly different from that of conventionally formed components. Corrosive environments for structural materials within advanced reactor environments include molten fluoride and chloride salts, liquid sodium and lead-bismuth, and high-temperature helium. The Advanced Materials and Manufacturing Technologies program within the Department of Nuclear Energy in the United States Department of Energy is assessing the unique concerns of MAM component corrosion and testing methodologies in advanced nuclear reactor environments. We discuss these concerns and testing strategies in this paper.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development and Demonstration of Large-Scale Metal Additive Manufacturing for Military Vehicle Applications (Final Report)

Additive Manufacturing (AM) is a process by which complex parts can be manufactured directly from a basic feedstock without the need for tooling. From a defense perspective, this will enable direct manufacture of parts for legacy equipment. However, current AM technologies are limited to small part sizes (approximately 1 cubic foot), slow production rates (approximately 1 cubic inch per hour) and expensive feedstocks (approximately $100/lb). The objective of this project was to explore the impact large-scale, high production rate additive manufacturing can have on military applications. First, the program explored the use of existing composite large-scale (Big Area Additive Manufacturing – BAAM) systems for both tooling and direct part replacement with the use of the Army’s Low Velocity Airdrop Delivery (LVAD) system and Willy’s Jeep. We report on the cost and time required for the development of both tooling and parts. Second, the program focused on expanding the BAAM technology to directly manufacture aluminum and steel components. A robotic welding system was developed, test articles manufactured and with a final deliverable of a steel bumper manufactured and installed on the Jeep. This report covers the results of the program and describes follow-on efforts to commercialize the technology.

36 MATERIALS SCIENCE↗

Chemical composition based machine learning model to predict defect formation in additive manufacturing

With a goal of exploiting additive manufacturing to improve the manufacturing of existing reactor materials, we developed a chemical composition-based machine learning model to predict the printability of any given alloy in laser powder bed fusion (L-PBF) using experimental data from peer-reviewed literature. We defined printability as the ability to avoid defects like cracking, balling, porosity, and lack of fusion, that are caused by thermal stresses (during solidification or liquation), molten pool disintegration into disconnected small beads or lack of heat input respectively. Our models predict the tendency of balling defect formation and porosity percentage for a given composition, under a given set of processing conditions. To predict the likelihood of balling defect, three models: a random forest classifier, a gradient boost regressor and a neural network were trained on a dataset containing both traditional alloys and high entropy alloys. The neural network model showed the highest accuracy of 92.3 % in predicting the balling defect formation. A random forest regressor, gradient boost regressor and neural network were trained and tested on a dataset of various alloys to predict porosity. The random forest regressor showed the best predictions with an R 2 score of 0.97. The models also revealed the relative importance of the input descriptors on defect-formation tendency. Of particular significance was the identification of carbon as an important element in determining the occurrence of balling and percent porosity in alloys like steel, as well as being moderately important to the percentage porosity in other alloys as well as steel. Manganese was also identified as a key descriptor for the percentage of porosity in steel and other alloys. Manganese’s low thermal conductivity and consistent presence in the dataset is the likely cause for its contribution. Carbon’s role is attributable to its relatively high specific heat and high melting temperature. In conclusion, our model serves as a swift, chemistry-based tool to design experiments and find modified compositions better suited for additive manufacturing.

36 MATERIALS SCIENCE↗

Evaluation of an Al-Ce alloy for laser additive manufacturing

Our present research in metal additive manufacturing (AM) focuses on designing processing parameters around existing alloys designed for traditional manufacturing. However, to maximize the benefits of AM, alloys should be designed to specifically take advantage of the unique thermal conditions of these processes. Furthermore, our study focuses on the development of a design methodology for alloys in AM, using a newly developed Al-Ce alloy as an initial case study. To evaluate the candidacy of this system for fusion based additive manufacturing, single-line laser melts were made on cast Al-12Ce plates using three different beam velocities (100, 200, and 300 mm/min). The microstructure was evaluated in the as-melted and heat treated conditions (24 hrs at 300°C). An extremely fine microstructure was observed within the weld pools, evolving from eutectic at the outer solid-liquid boundaries to a primary Al FCC dendritic/cellular structure nearer the melt-pool centerline. We rationalized the observed microstructures through the construction of a microstructure selection map for the Al-Ce binary system, which will be used to enable future alloy design. Interestingly, the heat treated samples exhibited no microstructural coarsening.

36 MATERIALS SCIENCE↗

Observation of keyhole-mode laser melting in laser powder-bed fusion additive manufacturing

Laser powder-bed fusion additive manufacturing of metals employs high-power focused laser beams. Typically, the depth of the molten pool is controlled by conduction of heat in the underlying solid material. But, under certain conditions, the mechanism of melting can change from conduction to so-called “keyhole-mode” laser melting. In this mode, the depth of the molten pool is controlled by evaporation of the metal. Keyhole-mode laser melting results in melt pool depths that can be much deeper than observed in conduction mode. In addition, the collapse of the vapor cavity that is formed by the evaporation of the metal can result in a trail of voids in the wake of the laser beam. In this paper, the experimental observation of keyhole-mode laser melting in a laser powder-bed fusion additive manufacturing setting for 316L stainless steel is presented. Finally, the conditions required to transition from conduction controlled melting to keyhole-mode melting are identified.

36 MATERIALS SCIENCE↗

Additive manufacturing: a challenge to nuclear nonproliferation

Additive manufacturing (AM) is a rapidly developing technology that allows industries to automate and simplify the production of highly complicated items. Recently, there are concerns that AM techniques have the potential to be utilized in the fields of nuclear weapons and nuclear enrichment technology. Presently, there are very few international or domestic export controls that apply to AM's role in the nuclear industry, constituting an unmanaged proliferation pathway. Pre-existing export controls focus on general concepts and processes and do not consider specific nuances of various techniques that are categorized as additive manufacturing. To introduce legislation and controls that will be effective in monitoring proliferation pathways, one must investigate and characterize AM techniques and their nuclear applications. This paper categorizes and ranks 33 AM techniques based on their potential impact on the nuclear fuel cycle and the development of nuclear weapons. Through this method of characterization and categorization, export controls would address specific AM nuclear proliferation risks without disrupting the entire industry and fuel cycle. Additionally, legislation employing this method would identify loopholes in export controls using a holistic approach to managing and monitoring proliferation pathways.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗