Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “thermal flexibility”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Investigation of Some Characteristics Related to PCM Thermal Capacitors

In order to provide greater flexibility, shorter computer time, and a parametric study, attention was devoted to an implicit numerical scheme. The experimental work involved outlining and monitoring approximately fourteen tests of an invertable capacitor. Surface and PCM temperatures were measured at several locations and photographs were made of the PCM during melting and solidification. Some typical experimental results are presented and discussed.

Griggs, E. I.↗
NASA NTRS1997

Optical Waveguide Solar Energy System for Lunar Materials Processing

This paper discusses results of our work on development of the Optical Waveguide (OW) Solar Energy System for Lunar Materials Processing. In the OW system as shown, solar radiation is collected by the concentrator which transfers the concentrated solar radiation to the OW transmission line consisting of low-loss optical fibers. The OW line transmits the solar radiation to the thermal reactor of the lunar materials processing plant. The feature of the OW system are: (1) Highly concentrated solar radiation (up to 104 suns) can be transmitted via flexible OW lines directly into the thermal reactor for materials processing: (2) Solar radiation intensity or spectra can be tailored to specific materials processing steps; (3) Provide solar energy to locations or inside of enclosures that would not otherwise have an access to solar energy; and (4) The system can be modularized and can be easily transported to and deployed at the lunar base.

Nakamura, T.↗
DOE OSTI2021

Evaluation of Phase Change Plaster/Paste Composites for Building Envelopes

Thermal energy storage (TES) materials increase a building’s thermal mass and provide the flexibility to shave and time-shift energy use. These materials are needed to enable grid-interactive efficient buildings, allowing building occupants to lower costs by leveraging free ambient heating/cooling as well as shifting consumption to cheaper electricity periods. Phase change materials (PCMs) that store heat through a solid-liquid/solid-solid transformation are of particular interest for TES because of their ability to store large amounts of energy across a constant temperature or very small temperature range. Furthermore, previous studies on PCM building envelopes evaluated products that may only be incorporated as part of new construction and are not easily applicable to existing, energy-intensive buildings. In this work, we leverage laboratory PCM characterization and whole-building energy simulation to study the energy and cost savings of PCM plaster/paste coatings, which can be applied post construction to both new builds and retrofits of existing buildings (about 40% of residential buildings in the United States fall into the retrofit category). We evaluated the energy impact of PCM plaster/paste composites for a single-family residential building in the United States, including layer design (location and thickness), composite properties (phase change temperature, energy density, and shape of the enthalpy curve), and U.S. climate zone. The enthalpy curve shape of PCM shows that phase change temperature and energy density are not the only two parameters that must be considered for PCM selection. Maximizing the energy density amid the effective TES zone is key to boosting energy savings. We also studied PCM price targets with the aim of achieving reasonable payback periods based on both block and time-of-use electricity rates. Moreover, we developed an empirical equation to provide a rough estimate of the energy savings potential of incorporating PCM without the need to perform detailed simulations. These results will help guide the selection and design of PCM plaster/paste composite elements for residential building envelopes.

ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATION↗
DOE OSTI2023

Thermal Energy Distribution System (TEDS) Operating Modes and Control Strategies

A Thermal Energy Delivery System was constructed at the Idaho National Laboratory for demonstrating distribution of thermal energy to and from co-located systems sited in the INL Dynamic Energy Transport and Integration Laboratory (DETAIL). DETAIL includes a flow loop simulating a pressurized water reactor, a high-temperature steam electrolysis unit and a thermal energy storage system. This report discusses the various operating modes and control strategies for enabling simultaneous, flexible and efficient transfer of heat from thermal energy sources to end users.

25 ENERGY STORAGE↗
DOE OSTI2020

Direct Recycling of Spent NCM Cathodes through Ionothermal Lithiation

Ionic liquids (ILs) are a family of nonconventional molten salts that offer many advantages, such as negligible vapor pressures, negligible flammability, wide liquidus ranges, good thermal stability, and much synthesis flexibility. The unique solvation environment of these ILs provides new reaction or flux media for controlling formation of solid-state materials with a minimum perturbation of morphologies. A successful lithiation via ionothermal synthesis using a cost-effective Li halide as Li source and recyclable ILs as solvents is reported in this study for the direct recycling of LiNi 1/3 Co 1/3 Mn 1/3 O 2 (NCM 111) cathodes. In addition, the ionic liquids can be readily recycled and reused after ionothermal lithiation. The lithiation of spent cathodes can enable the direct recycling of spent cathode materials in lithium-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2020

Combinatorial Synthesis and High-Throughput Characterization of Microstructure and Phase Transformation in Ni–Ti–Cu–V Quaternary Thin-Film Library

Ni–Ti–based shape memory alloys (SMAs) have found widespread use in the last 70 years, but improving their functional stability remains a key quest for more robust and advanced applications. Named for their ability to retain their processed shape as a result of a reversible martensitic transformation, SMAs are highly sensitive to compositional variations. Alloying with ternary and quaternary elements to fine-tune the lattice parameters and the thermal hysteresis of an SMA, therefore, becomes a challenge in materials exploration. Combinatorial materials science allows streamlining of the synthesis process and data management from multiple characterization techniques. In this study, a composition spread of Ni–Ti–Cu–V thin-film library was synthesized by magnetron co-sputtering on a thermally oxidized Si wafer. Composition-dependent phase transformation temperature and microstructure were investigated and determined using high-throughput wavelength dispersive spectroscopy, synchrotron X-ray diffraction, and temperature-dependent resistance measurements. Of the 177 compositions in the materials library, 32 were observed to have shape memory effect, of which five had zero or near-zero thermal hysteresis. These compositions provide flexibility in the operating temperature regimes that they can be used in. A phase map for the quaternary system and correlations of functional properties are discussed with respect to the local microstructure and composition of the thin-film library.

42 ENGINEERING↗
DOE OSTI2023

Porous bipolar polymers as organic cathodes for sustainable sodium/potassium-ion batteries

Redox-active porous polymers are becoming promising organic electrode materials for alkali-ion batteries because of their tunable pore size, flexible chemical structure, and high thermal stability. This work presents various porous bipolar polymers as cathodes in Na-ion batteries (NIBs) and K-ion batteries (KIBs). Two structural units containing carbonyl and amine active centers, respectively, were introduced into the repeating units of the polymers by the polycondensation of N,N,N',N'-tetrakis(4-aminophenyl)-1,4-phenylenediamine (TAP) and various dianhydrides. Here, the resulting bipolar polymers undergo multi-electron redox reactions involving both cations and anions during battery charge and discharge. The impacts of extended conjugation structures and porosity on the electrochemical performances were investigated by tuning the conjugation structures in the dianhydride monomers. The bipolar polymers with extended conjugation structures and small pore size exhibit superior electrochemical performance in NIBs and KIBs in terms of high redox potentials, long cycle life, and fast-charging capability, demonstrating great promise as organic cathode materials for alkali-ion batteries.

25 ENERGY STORAGE↗
NASA NTRS1982

Structural assembly demonstration experiment

The experiment is of an operational variety, designed to assess crew capability in Large Space System (LSS) assembly. The six Structural Assembly Demonstration Experiment objectives include: (1) the establishment of a quantitative correlation between LSS neutral buoyancy simulation and on-orbit assembly operations in order to enhance the validity of those assembly simulations; (2) the quantitative study of the capabilities and mechanics of human assembly in an Extravehicular Activity environment; (3) the further corroboration of the LSS Assembly Analysis cost algorithm through the obtainment of hard data base information; (4) the verification of LSS assembly techniques and timeless, as well as the identification of crew imposed loads and assembly aid requirements and concepts; (5) verification of a Launch/Assembly Platform structure concept for other LSS missions; and (6) lastly, to advance thermal control concepts through a flexible heat pipe.

Stokes, J. W.↗
NASA NTRS1983

An analytical investigation of shape control of large space structures by applied temperatures

An analytical procedure for the static shape control of flexible space structures subjected to thermal distortions is developed which is based on prescribing temperatures in control elements having much higher coefficients of thermal expansion than the main structure. The temperatures at the control elements are defined so as to minimize the overall thermal distortion of the structure from its ideal shape, and a matrix equation is obtained which can be solved for the set of optimum control temperatures. A formulation of the procedure for continuous structures governed by differential equations and a formulation for discrete (finite element modeled) structures governed by matrix equations are presented. The equations from the continuous formulation are employed for the shape control of a simple beam distorted by nonuniform heating, and the discrete formulation is applied in a general purpose finite-element structural analysis computer program for the shape control of a 750 m radiometer antenna reflector dish subjected to orbital heating. A reduction in thermal distortion by a factor of nearly 50 was obtained with the use of only seven control elements. Results for four different sets of control locations for the antenna are presented in which reductions in distortion of up to a factor of four were obtained.

Haftka, R. T.↗
NASA NTRS1998

Orbital Debris Impact Damage to Reusable Launch Vehicles

In an effort by the National Aeronautics and Space Administration (NASA), hypervelocity impact tests were performed on thermal protection systems (TPS) applied on the external surfaces of reusable launch vehicles (RLV) to determine the potential damage from orbital debris impacts. Three TPS types were tested, bonded to composite structures representing RLV fuel tank walls. The three heat shield materials tested were Alumina-Enhanced Thermal Barrier-12 (AETB-12), Flexible Reusable Surface Insulation (FRSI), and Advanced Flexible Reusable Surface Insulation (AFRSI). Using this test data, predictor equations were developed for the entry hole diameters in the three TPS materials, with correlation coefficients ranging from 0.69 to 0.86. Possible methods are proposed for approximating damage occurring at expected orbital impact velocities higher than tested, with references to other published work.

Robinson, Jennifer H.↗
NASA NTRS2004

New High-Temperature Membranes Developed for Proton Exchange Membrane Fuel Cells

Fuel cells are receiving a considerable amount of attention for potential use in a variety of areas, including the automotive industry, commercial power generation, and personal electronics. Research at the NASA Glenn Research Center has focused on the development of fuel cells for use in aerospace power systems for aircraft, unmanned air vehicles, and space transportation systems. These applications require fuel cells with higher power densities and better durability than what is required for nonaerospace uses. In addition, membrane cost is a concern for any fuel cell application. The most widely used membrane materials for proton exchange membrane (PEM) fuel cells are based on sulfonated perfluorinated polyethers, typically Nafion 117, Flemion, or Aciplex. However, these polymers are costly and do not function well at temperatures above 80 C. At higher temperatures, conventional membrane materials dry out and lose their ability to conduct protons, essential for the operation of the fuel cell. Increasing the operating temperature of PEM fuel cells from 80 to 120 C would significantly increase their power densities and enhance their durability by reducing the susceptibility of the electrode catalysts to carbon monoxide poisoning. Glenn's Polymers Branch has focused on developing new, low-cost membranes that can operate at these higher temperatures. A new series of organically modified siloxane (ORMOSIL) polymers were synthesized for use as membrane materials in a high-temperature PEM fuel cell. These polymers have an organic portion that can allow protons to transport through the polymer film and a cross-linked silica network that gives the polymers dimensional stability. These flexible xerogel polymer films are thermally stable, with decomposition onset as high as 380 C. Two types of proton-conducting ORMOSIL films have been produced: (1) NASA-A, which can coordinate many highly acid inorganic salts that facilitate proton conduction and (2) NASA-B, which has been produced and which incorporates strongly acidic (proton donating) functional groups into the polymer backbone. Both of these polymer films have demonstrated significantly higher proton conductivity than Nafion at elevated temperatures and low relative humidities. An added advantage is that these polymers are very inexpensive to produce because their starting materials are commodity chemicals that are commercially available in large volumes.

Kinder, James D.↗
NASA NTRS2018

Cryogenic Heat Transfer System

Disclosed herein is a cryogenic heat transfer system capable of transferring 50 W or more at cryogenic temperatures of 100.degree. K or less for use with cryocooler systems. In an embodiment, a cryogenic heat transfer system comprises a refrigerant contained within an inner chamber bound by a condenser in fluid communication with an evaporator through at least one flexible conduit, the condenser in thermal communication with the cold station of a cryocooler, and the evaporator positionable in thermal communication with a heat source, typically a radiation shield of a cryogenic chamber. A process to remove heat from a cryogenic chamber is also disclosed.

Chui, Talso C.↗
DOE OSTI2022

2022 FORCE Development Status Update

Due to the rapidly changing nature of the energy landscape in both the U.S. and abroad, including the increase in non-dispatchable variable renewable energy (VRE) deployment and the abundance of carbonbased dispatchable fuels, the Integrated Energy Systems (IES) program under the Department of Energy (DOE) has been engaged in determining whether IES could assist in providing nuclear power plants (NPPs) with a viable strategy for achieving future economic competitiveness. This includes enhanced dispatch flexibility for NPPs, thanks to thermal and electrical storage technology as well as the generation of ancillary commodities such as hydrogen, desalinated water, and synthetic fuels from the heat generated by NPPs. The technical and economic viability of these systems is of primary concern to the IES program, with the intent of providing insight to the wider nuclear energy community at large.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2026

In-Situ TEM Molten Salt Corrosion

Molten salt reactors (MSRs) offer a compelling pathway for next-generation nuclear energy, with advantages in thermal efficiency, inherent safety, and flexible fuel management. Yet, halide-based molten salts introduce significant materials challenges, particularly alloy corrosion. Alloy performance in these environments ultimately depends on understanding how corrosion initiates and progresses at the nanoscale, however most existing models rely on post-exposure characterization, leaving degradation mechanisms largely inferred rather than directly observed. NiCr alloys have garnered interest in MSRs applications as the Ni-based matrix provides strength and creep resistance, while Cr content offers oxidation resistance in air. However, NiCr corrosion resistance in chloride salts has proven poor due to preferential chromium dissolution, the formation of Cr-depleted pathways, and grain-boundary attack. This work aims to directly visualize corrosion of Ni-20Cr exposed to LiCl-KCl using in-situ Transmission Electron Microscopy (TEM) to capture real-time microstructural evolution during corrosion. Experiments will be performed at ~800 °C under controlled pressure conditions while utilizing Energy-Dispersive X-ray Spectroscopy (EDS) to analyze elemental redistribution. Observation of chromium depletion fronts, associated surface restructuring, and localized chloride enrichment are expected. Ultimately, this study is expected to provide a link between microscale processes and the macroscopic degradation behaviors relevant to MSR operation in advanced reactor environments. Simultaneously, this approach enables future in-situ investigations regarding alloy composition, salt chemistry, and their influence on corrosion pathways and long-term stability.?

36 - MATERIALS SCIENCE↗
NASA NTRS1992

The effects of Venus' thermal structure on buoyant magma ascent

The recent Magellan images have revealed a broad spatial distribution of surface volcanism on Venus. Previous work in modeling the ascent of magma on both Venus and Earth has indicated that the planetary thermal structure significantly influences the magmatic cooling rates and thus the amount of magma that can be transported to the surface before solidification. In order to understand which aspects of the thermal structure have the greatest influence on the cooling of ascending magma, we have constructed magma cooling curves for both plutonic and crack buoyant ascent mechanisms, and evaluated the curves for variations in the planetary mantle temperature, thermal gradient curvature with depth, surface temperature gradient, and surface temperature. The planetary thermal structure is modeled as T/T(sub 0) = 1-tau(1-Z/Z(sub 0)(exp n), where T is the temperature, T(sub 0) is the source depth temperature, tau = 1-(T(sub s)/T(sub 0)) where T(sub s) is the planetary surface temperature, Z is the depth, Z(sub 0) is the source depth, and n is a constant that controls thermal gradient curvature with depth. The equation is used both for mathematical convenience and flexibility, as well as its fit to the thermal gradients predicted by the cooling half-space models. We assume a constant velocity buoyant ascent, body-averaged magma temperatures and properties, an initially crystal-free magma, and the same liquidus and solidus for both Venus and Earth.

Sakimoto, S. E. H.↗
DOE OSTI2025

CSP Plant Optimization Study for the California Power Market (“CalCSP”) (Final Technical Report)

Concentrating Solar Power (CSP) with thermal energy storage offers a unique and strategic opportunity to support California’s clean energy transition. Unlike photovoltaic (PV) systems, CSP with thermal storage can generate electricity after sunset and during periods of high demand, making it a valuable complement to intermittent renewable resources. CSP also provides synchronous, inertia-contributing generation, long-duration storage, and flexible dispatch—capabilities increasingly important as thermal plants retire. This report summarizes the findings of the CSP Plant Optimization Study for the California Power Market or “CalCSP study,” which evaluated the technical, economic, environmental, and policy factors that influence the deployment of CSP technologies in California. The CalCSP study was conducted to assess how CSP can contribute to California’s long-term decarbonization goals while enhancing grid reliability, supporting local economic development, and making efficient use of land and transmission resources. It draws on detailed modeling of CSP performance and costs, site suitability analysis, policy reviews, and stakeholder engagement across utilities, regulators, developers, and community organizations. The analysis focuses on mature molten-salt tower technology and incorporates lessons learned from the global CSP fleet, distinguishing today’s CSP from earlier first-of-a-kind projects in the U.S. The findings support a more prominent role for CSP in California’s evolving clean energy landscape. With strategic planning, targeted policy support, and continued cost improvements, CSP can complement PV and batteries to deliver reliable, around-the-clock clean electricity—especially in areas with high solar resource and constrained grid capacity.

14 SOLAR ENERGY↗
NASA NTRS1983

Thermal analysis considerations for large space structures

A number of issues and needs relative to thermal analysis of large space structures and space stations are discussed. Some indications of trends in the Langley thermal-structural analysis research program consistent with the issues and needs are also presented. The main heat transfer mechanism in space is radiation; consequently, there is a need for a strong thrust on improved radiation analysis capability. Also the important interactions among temperatures, deformations, and controls need to be accounted for. Finite element analysis capability seems to be lagging behind lumped-parameter capability or heat pipe analysis. The Langley plan will include improving radiation analysis capability, evaluating the errors involved in certain approximate analysis and modeling techniques for large space trusses, and continuing the development of integrated thermal-structural finite elements with an emphasis on radiation heat transfer. Work will be initiated to develop finite element analysis techniques for heat pipes. Finally, optimization research activities will be oriented toward methods to design flexible orbiting structures to account for thermal and thermal deformation requirements.

Adelman, H. M.↗