Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “strain rate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Deformation and fracture characteristics of zirconium plate produced via ultrasonic additive manufacturing

Abstract The microstructural evolution, deformation modes, and fracture mechanisms of zirconium plate produced using ultrasonic additive manufacturing (UAM) are presented. In addition to conventional tensile testing techniques, digital image correlation captured highly variable strain accumulation in specimens loaded perpendicular or parallel to the build height (Z). When tested in parallel to Z, delamination at prior foil/foil interfaces creates strain localization noticeable in strain rate maps, whereas specimens loaded perpendicular to Z illustrate conventional strain hardening until necking accelerates delamination. Although bond strengths are statistically and spatially variable, in situ electron backscattering diffraction tests illustrate the ability for grains near interfaces to accommodate strain with twinning and slip modes consistent with conventionally produced zirconium alloys. Finally, mixtures of ductile and delamination-induced fracture highlight the interface-driven failure modes of UAM zirconium plate in the as-built condition. Graphic abstract

36 MATERIALS SCIENCE↗
DOE OSTI2023

Interplay of Mechanochemistry and Material Processes in the Graphite to Diamond Phase Transformation

The manifestation of intramolecular strains in covalent systems is widely known to accelerate chemical reactions and open alternative reaction paths. This process is moderately well understood for isolated molecules and unimolecular processes. However, in condensed matter processes such as phase transformations, material properties and structure may influence typical mechanochemical effects. Therefore, we utilize steered molecular dynamics to induce out of plane strains in graphite and compress the system under a constant strain rate to induce phase transformation. We show that the out of plane strain allows phase transformations to initiate at small amounts of compressive strain. Yet, in contrast to typical mechanochemical results, the sum of compressive and out of plane work needed to form a diamond has a local minimum due to altered defect formation processes during phase transformation. Additionally, these altered processes slow the kinetics of the phase transformation, taking longer from initiation to total material transformation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

FY2021 Improvements to the New CTH Code Verification & Validation Test Suite

Over the past few years, the CTH multiphysics hydrocode has overhauled its software quality and testing processes, implementing current best practices in software quality and building a robust V&V test suite comprised of traditional hydrocode verification problems, including ASC Tri-Lab Test Suite and Enhanced Tri-Lab Test Suite problems, as well as validation problems for some of CTH’s most frequently used equations of state, materials models, and other key capabilities. Substantial progress towards building this new test suite was made in FY19 and FY20. In FY21, the test suite has been expanded to include verification and validation tests of the Steinberg-Guinan-Lund (ST) viscoplastic model and the Johnson Cook (JFRAC) fracture model. Additionally, two new verification tests were added, covering hydrodynamics and high explosive (HE) modeling capabilities: the Kidder Gaussian density problem and the Escape of HE Products (EHEP) problem from the Tri-Lab Test Suite. This report discusses each of these test problems in detail. Verification test results are compared to analytic solutions. Validation test results are compared to experimental data. Wherever possible, convergence or mesh refinement studies are included. Additionally, while implementing the Kidder verification problem, a bug was identified that affects the use of tables to initialize pressure or density in 1D or 2D calculations. A brief discussion of the bug and its fix is included. CTH demonstrates good performance overall on the new test suite problems. Simulation results showed good agreement with analytic solutions for the Kidder problem, with convergence rates ranging between 1.8 and sub-linear, and relatively good agreement for the EHEP problem, though convergence rates for pressure and density were nearly 0. The ST and JFRAC strain rate loading verification tests show good agreement with analytic solutions. Likewise, CTH simulation results show good agreement with experimental validation data, including Taylor rod impact testing, for the materials tested. Future V&V work will focus on adding 2D and 3D versions of existing verification tests as well as adding validation tests of other frequently used capabilities such as other fracture models.

42 ENGINEERING↗
DOE OSTI2020

Kinetics of Failure in an Elastic Peridynamic Material

The dynamic behavior of an elastic peridynamic material with a nonconvex bond potential is studied. In spite of the material’s inherently unstable nature, initial value problems can be solved using essentially the same techniques as with conventional materials, both analytically and numerically. In a suitably constructed material model, small perturbations grow exponentially over time until the material fails. Additionally, the time for this growth is computed explicitly for a stretching bar that passes from the stable to the unstable phase of the material model. This time to failure represents an incubation time for the nucleation of a crack. The finiteness of the failure time in effect creates a rate dependence in the failure properties of the material. Thus, the unstable nature of the elastic material leads to a rate effect even though it does not contain any terms that explicitly include a strain rate dependence.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Creep deformation and cavitation in an additively manufactured Al-8.6Cu-0.4Mn-0.9Zr (wt%) alloy

Creep deformation and cavitation were investigated at 300 ºC in both tension and compression for an additively manufactured Al-8.6Cu-0.5Mn-0.9Zr (wt%) alloy in the as-fabricated state and after various aging treatments (aging at 300 °C/200 h or 350 °C/24 h and overaging at 400 °C/200 h). Creep mechanisms at 300 °C were determined by relating the measured creep response to corresponding microstructural and X-ray computed tomography observations. In compression, alloys in the as-fabricated and two aging conditions exhibited similarly high creep resistance. Overaging (400 °C/200 h) led to substantial coarsening of intragranular θ-Al2Cu precipitates and an expected drop in their Orowan strengthening contribution. In tension, minimum strain rates comparable to those in compression were obtained at any given stress; however, upon accumulation of some plastic strain in the matrix, creep cavities started to form, leading to accelerated tertiary stage creep deformation and rupture. Cavitation occurred exclusively along melt pool boundaries due to locally enhanced diffusion enabled by (i) large grain-boundary area in adjacent fine-grained zones and (ii) localization of creep strain in nearby heat-affected zones. Although cavity growth was initially diffusion-controlled, its rate was determined by matrix creep rate, consistent with constrained cavity growth mechanisms. This study reveals how microstructural complexities induced by the additive manufacturing process affect the creep and cavitation behavior of Al-Cu-Mn-Zr alloys. The underlying creep and cavitation mechanisms uncovered in this study point to pathways that improve the high-temperature properties of additively manufactured alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Development of a Stress Sensor for In-Situ High-Pressure Deformation Experiments Using Radial X-Ray Diffraction

We developed a stress sensor for in-situ deformation experiments using synchrotron radial X-ray diffraction. This stress sensor provided nearly diffraction-plane-independent stress that, when used in series with a sample, reduced the uncertainty of the average stress estimation acting on a sample. Here, we present the results of a study where pyrope was used as a stress sensor. Using a Deformation-DIA (D-DIA) high-pressure deformation apparatus, pyrope, olivine and alumina were deformed in the same run/cell assembly placed in series along the compression direction. Deformation experiments were conducted at pressures between 4 and 5 GPa and temperatures between 730 and 1273 K with strain-rates between 10 –5 and 10 –6 s –1 . Stresses estimated from various (hkl) planes in pyrope were nearly the same; i.e., pyrope is plastically isotropic with ≤10 % variation with (hkl). However, stresses from various (hkl) planes in olivine and alumina varied by approximately a factor of 3. Comparisons between average stresses inferred from pyrope and those from different diffraction planes in olivine and alumina showed that the average stress in these materials evolved from low-end stress, estimated from various (hkl) planes at small strain, to high-end stress at a large strain. This suggests that the rate-controlling slip system in these materials changes from the soft to the hard slip system with strain.

58 GEOSCIENCES↗
DOE OSTI2020

A novel framework for elastoplastic behaviour of anisotropic solids

A general framework for developing nonlinear hyperelastic/plastic constitutive laws for anisotropic solids experiencing large strains and strain rates has been developed. The proposed framework does not rely on the “a priori” known strain energy function, but instead introduces a physical decomposition of the material element into seven physically independent stress bearing mechanisms, each of which has a constitutive law in terms of internal moments described by a scalar function of a single variable. Furthermore, the model has been encoded into a combined finite-discrete element method and tested against static geomechanical test data. The numerical validation experiments show the model can reproduce plastic anisotropic behavior in both biaxial and uniaxial loading of a geomaterial.

58 GEOSCIENCES↗
DOE OSTI2024

Deformation and Delamination of Dynamically Bulging Bilayered Films

We employ finite element simulations to study the dynamic bulging of films under shock tube conditions and compare these responses with quasi-static bulging. Both scenarios subject the film to time-varying pressure. Two film types are considered: uniform material films and bilayers with a relatively soft interior layer and a hard exterior layer. The interface between the materials in the bilayer cases is modeled as a cohesive zone that follows a bilinear normal traction-separation cohesive law. Additionally, bilayer films with preexisting cracks in the interior layer are analyzed. Parametric studies are also conducted to explore the effects of loading rate and specimen size. The mechanical response of all materials is assumed to be strain-rate independent, focusing solely on the inertial effects in the response of the films under dynamic loading, and the absence of such effects under quasi-static loading. The results indicate that quasi-static bulging exhibits a predictable plate bending like deformation. In contrast, depending on the loading rate and specimen size, dynamic bulging can give rise to elastic waves, and a sequence of deformation processes including initial uniform acceleration, followed by bending-like deformation, and finally through-thickness biaxial stretching. Dynamic loading also leads to larger bulge formation and greater deformation than quasi-static loading. A key finding is the role of preexisting cracks in driving delamination under dynamic loading, which is absent in quasi-static loading. This work enhances our understanding of dynamic bulging and motivates further research on characterizing delamination in layered films using dynamic bulge tests.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Unraveling the implications of finite specimen size on the interpretation of dynamic experiments for polycrystalline aluminum through direct numerical simulations

Normal and Pressure-shear plate impact (NPI and PSPI) experiments are popular experimental techniques for studying the mean-field macroscopic behavior of polycrystalline metals under high-rate dynamic loading. However, since both configurations rely upon geometry for subjecting the specimen to high strain rates, these experiments often involve a limited specimen size. Moreover, because of the inherent heterogeneities present within polycrystalline metals, it is difficult to ascertain if the size of the specimen and/or regions where measurements are made are sufficiently large for making representative inferences about the mean-field macroscopic properties from single-point velocity measurements. In the present study, we quantify the expected measurement variability on observable point measurements in NPI and PSPI experiments by carrying out direct numerical simulations (DNS) of statistically representative polycrystalline microstructures subjected to dynamic compression and compression-shear loading. In particular, we consider the role of specific material heterogeneities (e.g. the grain-to-grain difference in size, crystallographic orientation) on dispersion in the normal and transverse particle velocity records and on local fluctuations in key state variables (e.g. velocity, accumulated plastic strain) by incorporating these effects directly into a representative synthetic microstructure geometry and crystalline description of pure polycrystalline aluminum. The form of the present study is a large parametric investigation, consisting of ten ensembles of one hundred simulations. Each of the thousand simulations reflects a randomly realized synthetic microstructure in one of five cases of decreasing average grain size for the two loading configurations. Our analysis of the DNS results demonstrates that for both of these experimental configurations, the grain size directly correlates with the coefficient of variation (CV) in simulated point measurements, showing a convergent decrease in CV to zero (i.e. particle velocity record approaches the mean-field value) with decreasing grain size. Remarkably, the magnitude of variations in the particle velocity record is shown to be largest where the deviatoric stresses are most significant. In the case of NPI, this occurs at the elastic and plastic wavefront, whereas, in the case of PSPI, the magnitude of fluctuations are approximately constant throughout the experimental window time. The reasoning for the scatter in particle velocity due to the heterogeneous microstructure is demonstrated to be dependent on the mechanisms for accommodating deformation and on the interaction of reflection waves generated at sites of heterogeneities occurring at the scale of grains. Lastly, we develop a power-law description for the magnitude of scattering versus characteristic length, which provides a statistical framework for assessing the required number of grains per characteristic specimen dimension for minimizing scatter within these two experimental configurations (NPI, PSPI).

36 MATERIALS SCIENCE↗
DOE OSTI2024

Digital image correlation and infrared thermography data for seven unique geometries of 304L stainless steel

Material Testing 2.0 (MT2.0) is a paradigm that advocates for the use of rich, full-field data, such as from digital image correlation and infrared thermography, for material identification. By employing heterogeneous, multi-axial data in conjunction with sophisticated inverse calibration techniques such as finite element model updating and the virtual fields method, MT2.0 aims to reduce the number of specimens needed for material identification and to increase confidence in the calibration results. To support continued development, improvement, and validation of such inverse methods—specifically for rate-dependent, temperature-dependent, and anisotropic metal plasticity models—we provide here a thorough experimental data set for 304L stainless steel sheet metal. The data set includes full-field displacement, strain, and temperature data for seven unique specimen geometries tested at different strain rates and in different material orientations. Commensurate extensometer strain data from tensile dog bones is provided as well for comparison. We believe this complete data set will be a valuable contribution to the experimental and computational mechanics communities, supporting continued advances in material identification methods.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Instability of an electron-plasma shear layer in an externally imposed strain flow

The E x B shear instability of a two-dimensional (2D) filament (i.e., a thin, rectangular strip perpendicular to the magnetic field) of magnetized pure electron plasma is investigated experimentally in the presence of an externally imposed strain flow. Data are acquired using a specialized Penning–Malmberg trap in which strain flows can be applied in 2D by biasing segmented electrodes surrounding the plasma. The E x B drift dynamics are well-described by the Drift-Poisson equations, which are isomorphic to the 2D Euler equations describing ideal fluids. Thus, the experimental results correspond to the Rayleigh instability of a shear layer in a 2D ideal fluid, where the electron density is analogous to the fluid vorticity. Shear layers are prepared by stretching initially axisymmetric electron vortices using a strong, applied strain flow. The data at early times are in quantitative agreement with a linear model which extends Rayleigh’s work to account for the influence of an external strain flow. In the presence of weak strain, the system approximately maintains a phase relationship that corresponds to an instantaneous Rayleigh eigenmode. The instability develops into the nonlinear regime later in time and at smaller spatial scales as the strain rate is increased. A secondary vortex pairing instability is observed, but it is suppressed when the strain-to-vorticity ratio exceeds roughly 0.025. In this way, vorticity transport perpendicular to the filament is diminished due to the applied strain.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

A surprising proliferation of detwinning in β -tin at extreme loading rates

Integrating data from dynamic compression experiments of condensed matter across three national laboratories has led to insight and quantitative calibration of materials strength over decades of loading rate. For many materials, a single strength model (such as PTW) is sufficient to capture the flow-stress strain rate relationship which is monotonic. Here, we show here that β -tin, a tetragonal metal, exhibits dramatic deviations from this behavior. Naive fitting to a single PTW model is insufficient to capture the behavior; indeed, such resulting inferred flow stress versus strain exhibits a non-monotonic behavior. We suggest a resolution to this by proposing that in β -tin there are important Bauschinger effects arising from favorable conditions for twinning and detwinning. A simple yield surface model when paired with PTW hardening captures the experimental data.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A Geomechanical Model for Gas Hydrate Bearing Sediments Incorporating High Dilatancy, Temperature, and Rate Effects

The geomechanical behavior of methane hydrate bearing sediments (MHBS) is influenced by many factors, including temperature, fluid pressure, hydrate saturation, stress level, and strain rate. The paper presents a visco-elastoplastic constitutive model for MHBS based on an elastoplastic model that incorporates the effect of hydrate saturation, stress history, and hydrate morphology on hydrate sediment response. The upgraded model is able to account for additional critical features of MHBS behavior, such as, high-dilatancy, temperature, and rate effects. The main components and the mathematical formulation of the new constitutive model are described in detail. The upgraded model is validated using published triaxial tests involving MHBS. The model agrees overly well with the experimental observations and is able to capture the main features associated with the behavior of MHBS.

15 GEOTHERMAL ENERGY↗
DOE OSTI2023

Assessing continuum plasticity postulates with grain stress and local strain measurements in triaxially compressed sand

Critical state and continuum plasticity theories have been used in research and engineering practice in soil and rock mechanics for decades. These theories rely on postulated relationships between material stresses and strains. Some classical postulates include coaxiality between stress and strain rates, stress–dilatancy relationships, and kinematic assumptions in shear bands. Although numerical and experimental data have quantified the strains and grain kinematics in such experiments, little data quantifying grain stresses are available. Here, we report the first-known grain stress and local strain measurements in triaxial compression tests on synthetic quartz sands using synchrotron X-ray tomography and 3D X-ray diffraction. We use these data to examine the micromechanics of shear banding, with a focus on coaxiality, stress-dilatancy, and kinematics within bands. Our results indicate the following: 1) elevated deviatoric stress, strain, and stress ratios in shear bands throughout experiments; 2) coaxial principal compressive stresses and strains throughout samples; 3) significant contraction along shear bands; 4) vanishing volumetric strain but nonvanishing stress fluctuations throughout samples at all stages of deformation. Our results provide some of the first-known in situ stress and strain measurements able to aid in critically evaluating postulates employed in continuum plasticity and strain localization theories for sands.

42 ENGINEERING↗
DOE OSTI2022

The Challenges of Modeling Defect Behavior and Plasticity across Spatial and Temporal Scales: A Case Study of Metal Bilayer Impact

Atomistic molecular dynamics (MD) and a microstructural dislocation density-based crystalline plasticity (DCP) framework were used together across time scales varying from picoseconds to nanoseconds and length scales spanning from angstroms to micrometers to model a buried copper–nickel interface subjected to high strain rates. The nucleation and evolution of defects, such as dislocations and stacking faults, as well as large inelastic strain accumulations and wave-induced stress reflections were physically represented in both approaches. Both methods showed similar qualitative behavior, such as defects originating along the impactor edges, a dominance of Shockley partial dislocations, and non-continuous dislocation distributions across the buried interface. The favorable comparison between methods justifies assumptions used in both, to model phenomena, such as the nucleation and interactions of single defects and partials with reflected tensile waves, based on MD predictions, which are consistent with the evolution of perfect and partial dislocation densities as predicted by DCP. This substantiates how the nanoscale as modeled by MD is representative of microstructural behavior as modeled by DCP.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Sustained strain applied at high rates drives dynamic tensioning in epithelial cells

Epithelial cells experience long lasting loads of different magnitudes and rates. How they adapt to these loads strongly impacts tissue health. Yet, much remains unknown about the evolution of cellular stress in response to sustained strain. Here, by subjecting cell pairs to sustained strain, we report a bimodal stress response, where in addition to the typically observed stress relaxation, a subset of cells exhibits a dynamic tensioning process with significant elevation in stress within 100 s, resembling active pulling-back in muscle fibers. Strikingly, the fraction of cells exhibiting tensioning increases with increasing strain rate. The tensioning response is accompanied by actin remodeling, and perturbation to actin abrogates it, supporting cell contractility’s role in the response. Collectively, our data show that epithelial cells adjust their tensional states over short timescales in a strain-rate dependent manner to adapt to sustained strains, demonstrating that the active pulling-back behavior could be a common protective mechanism against environmental stress.

bioinformatics↗
DOE OSTI2021

Impact-induced twinning in a magnesium alloy under different stress conditions

We investigate deformation twinning in a highly textured magnesium alloy plate of Mg-3.1%Al-0.9%Zn-0.4%Mn under edge-on impact with in situ, synchrotron-based, ultrafast X-ray diffraction measurements, and corresponding stress states are simulated with the finite element method. Deformation twinning and its anisotropy under the triaxial stress condition are explained by a statistical analysis of resolved shear stress. The critical resolved shear stress criterion is applicable under complicated stress conditions induced by high strain rate impact loading. Three typical simple stress conditions are further explored as verification and application cases: uniaxial-stress, uniaxial-strain, and plane-stress. Extension twinning in the magnesium alloy is prone to occur for impact loading applied perpendicular to the crystallographic c-axis, regardless of the exact stress conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Mechanical creep testing and characterization of Cr coated Zircaloy

Zirconium based cladding has been developed for use in light water reactor fuel applications due to the material’s desirable low neutron scattering cross section. To help improve corrosion resistance in accident conditions, such as a loss of coolant accident (LOCA), a chromium coating can be applied to the outer diameter of the Zircaloy tube. Cladding strength at reactor relevant temperatures is important for the structural performance. Stress relaxation creep testing was performed on Cr coated Zircaloy-4 to measure strain rate as a function of stress for 350 and 650°C. These were performed at both 5 ± 1 % and 7.5 ± 1 % strain. The lower temperature provides results near normal operating temperature, while the higher temperature provides results relevant to off-normal conditions where recrystallization will take place. Characterization was also performed to analyze the structure of the Cr coating and Zircaloy-4 as well as the interface between the two.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗