Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “shock wave”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

Reynolds number effects on shock-wave turbulent boundary-layer interactions - A comparison of numerical and experimental results

An experiment is described that tests and guides computations of a shock-wave turbulent boundary-layer interaction flow over a 20-deg compression corner at Mach 2.85. Numerical solutions of the time-averaged Navier-Stokes equations for the entire flow field, employing various turbulence models, are compared with the data. Each model is critically evaluated by comparisons with the details of the experimental data. Experimental results for the extent of upstream pressure influence and separation location are compared with numerical predictions for a wide range of Reynolds numbers and shock-wave strengths.

Horstman, C. C.↗

Interaction between a normal shock wave and a turbulent boundary layer at high transonic speeds. II - Wall shear stress

Asymptotic methods are used to calculate the shear stress at the wall for the interaction between a normal shock wave and a turbulent boundary layer on a flat plate. A mixing length model is used for the eddy viscosity. The shock wave is taken to be strong enough that the sonic line is deep in the boundary layer and the upstream influence is thus very small. It is shown that unlike the result found for laminar flow an asymptotic criterion for separation is not found; however, conditions for incipient separation are computed numerically using the derived solution for the shear stress at the wall. Results are compared with available experimental measurements.

Liou, M. S.↗

Three-Dimensional Navier-Stokes Simulations with Two-Equation Turbulence Models of Intersecting Shock-Waves/Turbulent Boundary Layer at Mach 8.3

An investigation of the numerical simulation with two-equation turbulence models of a three-dimensional hypersonic intersecting (SWTBL) shock-wave/turbulent boundary layer interaction flow is presented. The flows are solved with an efficient implicit upwind flux-difference split Reynolds-averaged Navier-Stokes code. Numerical results are compared with experimental data for a flow at Mach 8.28 and Reynolds number 5.3x10(exp 6) with crossing shock-waves and expansion fans generated by two lateral 15 fins located on top of a cold-wall plate. This experiment belongs to the hypersonic database for modeling validation. Simulations show the development of two primary counter-rotating cross-flow vortices and secondary turbulent structures under the main vortices and in each corner singularity inside the turbulent boundary layer. A significant loss of total pressure is produced by the complex interaction between the main vortices and the uplifted jet stream of the boundary layer. The overall agreement between computational and experimental data is generally good. The turbulence modeling corrections show improvements in the predictions of surface heat transfer distribution and an increase in the strength of the cross-flow vortices. Accurate predictions of the outflow flowfield is found to require accurate modeling of the laminar/turbulent boundary layers on the fin walls.

Bardina, J. E.↗

Partial Spreading of a Laser Beam into a Light Sheet by Shock Waves and Its Use as a Shock Detection Technique

It is observed that when a laser beam is allowed to fall on a shock surface at a grazing incidence, a small part of the beam spreads out in a thin, diverging sheet of light normal to the surface, and both upstream and downstream of the shock. The phenomenon is visualized by observing a cross section of the light sheet on a screen placed normal to the laser path after it touches a shock. The light sheet disappears when the beam is moved to any other locations where there is no shock or the beam pierces the shock surface, i.e., at a non-grazing incidence. The spread angle of the light sheet is considerably higher than the angle by which the beam may bend as it passes through the shock, which produces a small difference of refractive index. Various details indicate that the spread light is a result of diffraction of a small part of the laser beam by the shock whose thickness is nearly the same as that of the laser wavelength. Shocks formed in underexpanded free jets of fully expanded Mach numbers 1.4 to 1.8 are used for this experiment. The above optical phenomenon is used as the basis of a novel shock detection technique which depends on sensing the spread light using a photomultiplier tube (PMT). The locations of the shock surfaces in the underexpanded supersonic jet, obtained using this technique, match with those inferred from the Schlieren photographs and velocity measurements. Moreover, if the shock oscillates, a periodic PMT signal is obtained which provides information about the frequency and amplitude of shock motion.

Panda, J.↗

PIV Measurements of Shock-Wave/Boundary-Layer Interactions at Mach 2.5 in a Circular Test Section

The particle image velocimetry (PIV) measurement technique has been applied to make detailed measurements in an impinging shock-wave/boundary-layer interaction (SWBLI) flowfield in a test section of circular cross-section. By virtue of this test section geometry, the flowfields studied are free from effects of the complex coupling of sidewall and corner interaction into the primary impinging shock interaction typical of a rectangular test section. The cone-cylinder shock generator hardware was arranged in both coaxial alignment with the test section to generate axisymmetric SWBLIs and in offset positions to generate swept SWBLIs. The angle of the conical section was also varied to alter the strength of the impinging shock wave. The application of the PIV technique in this test section required meticulous design to provide adequate optical access without disturbing the SWBLI flow. Details of the stereoscopic PIV apparatus and the velocity measurements obtained for a Mach 2.5 freestream are presented. Key features of the mean velocity and turbulent stress fields are highlighted. This data set should enable validation of computational fluid dynamics results for these flowfields.

Shockwave Boundary Layer Interaction↗

PIV Measurements of Shock-Wave/Boundary-Layer Interactions at Mach 2.5 in a Circular Test Section

The particle image velocimetry (PIV) measurement technique has been applied to make detailed measurements in an impinging shock-wave/boundary-layer interaction (SWBLI) flowfield in a test section of circular cross-section. By virtue of this test section geometry, the flowfields studied are free from effects of the complex coupling of sidewall and corner interaction into the primary impinging shock interaction typical of a rectangular test section. The cone-cylinder shock generator hardware was arranged in both coaxial alignment with the test section to generate axisymmetric SWBLIs and in offset positions to generate swept SWBLIs. The angle of the conical section was also varied to alter the strength of the impinging shock wave. The application of the PIV technique in this test section required meticulous design to provide adequate optical access without disturbing the SWBLI flow. Details of the stereoscopic PIV apparatus and the velocity measurements obtained for a Mach 2.5 freestream are presented. Key features of the mean velocity and turbulent stress fields are highlighted. This data set should enable validation of computational fluid dynamics results for these flowfields.

Shockwave Boundary Layer Interaction↗

Laser Light Scattering Diagnostic for Measurement of Flow Velocity in Vicinity of Propagating Shock Waves

A laser light scattering diagnostic for measurement of dynamic flow velocity at a point is described. The instrument is being developed for use in the study of propagating shock waves and detonation waves in pulse detonation engines under development at the NASA Glenn Research Center (GRC). The approach uses a Fabry-Perot interferometer to measure the Doppler shift of laser light scattered from small (submicron) particles in the flow. The high-speed detection system required to resolve the transient response as a shock wave crosses the probe volume uses fast response photodetectors, and a PC based data acquisition system. Preliminary results of measurements made in the GRC Mach 4, 10 by 25 cm supersonic wind tunnel are presented. Spontaneous condensation of water vapor in the flow is used as seed. The tunnel is supplied with continuous air flow at up to 45 psia and the flow is exhausted into the GRC laboratory-wide altitude exhaust system at pressures down to 0.3 psia.

Seasholtz, Richard G.↗

Experimental Investigation of Unsteady Shock Wave Turbulent Boundary Layer Interactions About a Blunt Fin

A series of experiments were performed to investigate the effects of Mach number variation on the characteristics of the unsteady shock wave/turbulent boundary layer interaction generated by a blunt fin. A single blunt fin hemicylindrical leading edge diameter size was used in all of the experiments which covered the Mach number range from 2.0 to 5.0. The measurements in this investigation included surface flow visualization, static and dynamic pressure measurements, both on centerline and off-centerline of the blunt fin axis. Surface flow visualization and static pressure measurements showed that the spatial extent of the shock wave/turbulent boundary layer interaction increased with increasing Mach number. The maximum static pressure, normalized by the incoming static pressure, measured at the peak location in the separated flow region ahead of the blunt fin was found to increase with increasing Mach number. The mean and standard deviations of the fluctuating pressure signals from the dynamic pressure transducers were found to collapse to self-similar distributions as a function of the distance perpendicular to the separation line. The standard deviation of the pressure signals showed initial peaked distribution, with the maximum standard deviation point corresponding to the location of the separation line at Mach number 3.0 to 5.0. At Mach 2.0 the maximum standard deviation point was found to occur significantly upstream of the separation line. The intermittency distributions of the separation shock wave motion were found to be self-similar profiles for all Mach numbers. The intermittent region length was found to increase with Mach number and decrease with interaction sweepback angle. For Mach numbers 3.0 to 5.0 the separation line was found to correspond to high intermittencies or equivalently to the downstream locus of the separation shock wave motion. The Mach 2.0 tests, however, showed that the intermittent region occurs significantly upstream of the separation line. Power spectral densities measured in the intermittent regions were found to have self-similar frequency distributions when compared as functions of a Strouhal number for all Mach numbers and interaction sweepback angles. The maximum zero-crossing frequencies were found to correspond with the peak frequencies in the power spectra measured in the intermittent region.

Barnhart, Paul J.↗

Boundary Shock Waves

Gas flow at high speed out of solid or liquid surface accompanied by heat transfer investigated for boundary shock wave occurrence

SHOCK WAVE↗

Molecular shock waves in the BN-KL region of Orion

The H2, CO, and OH IR emission-line intensities in the BN-KL region of Orion are modeled by shock waves traveling at 36 km/s with respect to an ambient gas of density 200,000 per cu cm, ionization fraction of less than 3 x 10 to the -7th, CO abundance of approximately 0.0003, and transverse magnetic field of 0.45 milligauss. A global model is considered in which the shock waves are driven by strong winds emanating from KL. The mass-loss rate has been not less than 0.003 solar mass per year for approximately 1000 years. The total wind energy released from the star is not less than 5 x 10 to the 47th ergs. The total ejected momentum is approximately 10 to the 41st g cm/S, sufficient to disrupt the dense cloud surrounding BN-KL.

Chernoff, D. F.↗

Local stability analysis for a planar shock wave

A procedure to study the local stability of planar shock waves is presented. The procedure is applied to a Rankine-Hugoniot shock in a divergent/convergent nozzle, to an isentropic shock in a divergent/convergent nozzle, and to Rankine-Hugoniot shocks attached to wedges and cones. It is shown that for each case, the equation governing the shock motion is equivalent to the damped harmonic oscillator equation.

Salas, M. D.↗

Turbulence amplification in shock-wave boundary-layer interaction

Attention is directed to the acoustics research of the 1950s and 1960s for guidance in understanding and quantizing the turbulence amplification that can occur in regions of shock-wave boundary-layer interaction. Three primary turbulence amplifier-generator mechanisms are identified and shown, by linear analysis, to be responsible for turbulence amplification across a shock wave in excess of 100% of the incident turbulence intensity.

Anyiwo, J. C.↗

Electron acceleration to high energies at quasi-parallel shock waves in the solar corona

In the solar corona shock waves are generated by flares and/or coronal mass ejections. They manifest themselves in solar type 2 radio bursts appearing as emission stripes with a slow drift from high to low frequencies in dynamic radio spectra. Their nonthermal radio emission indicates that electrons are accelerated to suprathermal and/or relativistic velocities at these shocks. As well known by extraterrestrial in-situ measurements supercritical, quasi-parallel, collisionless shocks are accompanied by so-called SLAMS (short large amplitude magnetic field structures). These SLAMS can act as strong magnetic mirrors, at which charged particles can be reflected and accelerated. Thus, thermal electrons gain energy due to multiple reflections between two SLAMS and reach suprathermal and relativistic velocities. This mechanism of accelerating electrons is discussed for circumstances in the solar corona and may be responsible for the so-called 'herringbones' observed in solar type 2 radio bursts.

Mann, G.↗

Investigation of the Attenuation of Plane Shock Waves Moving over very Rough Surfaces

Experimental measurements of the attenuation of plane shock waves moving over rough walls have been made in a shock tube. Measurements of the boundary-layer characteristics, including thickness and velocity distribution behind the shock, have also been made with the aid of new cal techniques which provide direct information on the local boundary-layer conditions at the rough walls. Measurements of shock speed and shock pressure ratio are presented for both smooth-wall and rough-wall flow over lengths of machined-smooth and rough strips which lined all four walls of the shock tube. A simplified theory based on Von Karman's expression for skin-friction coefficient for flow over rough walls, along with a wave-model concept and extensions to include time effects, is presented. In this theory, the shock-tube flow is assumed to be one-dimensional at all times and the wave-model concept is used to relate the local layer growth to decreases in shock strength. This concept assumes that local boundary-layer growths act as local mass-flow sinks, which give rise to expansion waves which, in turn, overtake the shock and lower its mass flow accordingly.

Huber, Paul W.↗