Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “sensor model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Improved Earth Sensor Performance Using a Sequentially Correlated Noise Model

Spacecraft attitude estimation by means of an extended Kalman filter requires a reasonably true model of the inherent noise of each sensor. For some sensors, the largest uncorrected noise comes not from the sensor itself, but from errors in the model for the predicted observations. This is certainly the case for Earth horizon sensors. The Earth horizon as seen from low Earth orbit is nearly a circle whose radius depends primarily on altitude. A straightforward latitude-dependent correction is added to this to account for the oblateness of the Earth. There also are both seasonal and stochastic variations in the horizon height. The seasonal variations can be predicted to some limited degree based on models derived from historical data. The stochastic component characteristically shows variations that are correlated both in time and space but which are unpredictable over long time spans. This work investigates whether Earth horizon sensor performance can be improved by solving for its systematic error as an augmentation of an attitude Kalman filter. It is found that using only Earth and Sun sensors, the augmented state is not fully observable. Even when magnetometer data is included, only the pitch axis component of the error can be improved; the roll component is unobservable.

Sedlak, J.↗
NASA NTRS1999

Improved Earth Sensor Performance Using a Sequentially Correlated Noise Model

Spacecraft attitude estimation by means of an extended Kalman filter requires a reasonably true model of the inherent noise of each sensor. For some sensors, the largest uncorrected noise comes not from the sensor itself, but from errors in the model for the predicted observations. This is certainly the case for Earth horizon sensors. The Earth horizon as seen from low Earth orbit is nearly a circle whose radius depends primarily on altitude. A straightforward latitude-dependent correction is added to this to account for the oblateness of the Earth. There also are both seasonal and stochastic variations in the horizon height. The seasonal variations can be predicted to some limited degree based on models de(ived from historical data. The stochastic component characteristically shows variations that are correlated both in time and space but which are unpredictable over long time spans. This work investigates whether Earth horizon sensor performance can be improved by solving for its systematic error as an augmentation of an attitude Kalman filter. It is found that using only Earth and Sun sensors, the augmented state is not fully observable. Even when magnetometer data is included, only the pitch axis component of the error can be improved; the roll component is unobservable.

Sedlak, Joseph↗
NASA NTRS1982

Horizon sensor errors calculated by computer models compared with errors measured in orbit

Using a computer program to model the earth's horizon and to duplicate the signal processing procedure employed by the ESA (Earth Sensor Assembly), errors due to radiance variation have been computed for a particular time of the year. Errors actually occurring in flight at the same time of year are inferred from integrated rate gyro data for a satellite of the TIROS series of NASA weather satellites (NOAA-A). The predicted performance is compared with actual flight history.

Ward, K. A.↗
NASA NTRS1997

A Generative Control Capability for a Model-based Executive

This paper describes Burton, a core element of a new generation of goal-directed model-based autonomous executives. This executive makes extensive use of component-based declarative models to analyze novel situations and generate novel control actions both at the goal and hardware levels. It uses an extremely efficient online propositional inference engine to efficiently determine likely states consistent with current observations and optimal target states that achieve high level goals. It incorporates a flexible generative control sequencing algorithm within the reactive loop to bridge the gap between current and target states. The system is able to detect and avoid damaging and irreversible situations, After every control action it uses its model and sensors to detect anomalous situations and immediately take corrective action. Efficiency is achieved through a series of model compilation and online policy construction methods, and by exploiting general conventions of hardware design that permit a divide and conquer approach to planning. The paper presents a formal characterization of Burton's capability, develops efficient algorithms, and reports on experience with the implementation in the domain of spacecraft autonomy. Burton is being incorporated as one of the key elements of the Remote Agent core autonomy architecture for Deep Space One, the first spacecraft for NASA's New Millenium program.

Williams, Brian C.↗
NASA NTRS2008

Using Sensor Web Processes and Protocols to Assimilate Satellite Data into a Forecast Model

The goal of the Sensor Management Applied Research Technologies (SMART) On-Demand Modeling project is to develop and demonstrate the readiness of the Open Geospatial Consortium (OGC) Sensor Web Enablement (SWE) capabilities to integrate both space-based Earth observations and forecast model output into new data acquisition and assimilation strategies. The project is developing sensor web-enabled processing plans to assimilate Atmospheric Infrared Sounding (AIRS) satellite temperature and moisture retrievals into a regional Weather Research and Forecast (WRF) model over the southeastern United States.

Goodman, H. Michael↗
NASA NTRS1990

Sensor fusion II: Human and machine strategies; Proceedings of the Meeting, Philadelphia, PA, Nov. 6-9, 1989

Various papers on human and machine strategies in sensor fusion are presented. The general topics addressed include: active vision, measurement and analysis of visual motion, decision models for sensor fusion, implementation of sensor fusion algorithms, applying sensor fusion to image analysis, perceptual modules and their fusion, perceptual organization and object recognition, planning and the integration of high-level knowledge with perception, using prior knowledge and context in sensor fusion.

Schenker, Paul S.↗
DOE OSTI2025

Accurate and rapid acoustic damage characterization in complex structures using sparse sensor networks and deep learning models

Damage diagnosis in critical components is essential for ensuring the safety and reliability of operations across industries, spanning manufacturing, aerospace, and energy. Traditional acoustic nondestructive testing methods primarily focus on detecting defects through the direct scattering of single-mode incident waves from the damage, which limit their applicability to simple structures and small inspection areas. Our earlier research demonstrated that machine learning algorithms combined with sparse sensor networks can identify critical defect signatures even from multiply scattered, multi-mode acoustic signals, indicating the potential for improved defect inspection in complex, real-world structures. In this work, we demonstrate the successful implementation of this approach in a fixed sensor configuration to rapidly and accurately detect simulated defects in a geometrically complex, real-world structure, a brake rotor hub. Three different types of defects were physically simulated on the surface of the hub, and the collected data were used to train an autoencoder-based deep learning model. Two models were tested, one using single measurements and the other using multiple measurements taking advantage of the spatial distribution of the sensor network. After training, the multi-measurement model achieved 100 % accuracy in identifying, classifying, and locating unseen, unique damages. This work illustrates the potential of the proposed method for a wide range of industrial applications.

36 MATERIALS SCIENCE↗
DOE OSTI2016

USGS VDP Infrasound Sensor Evaluation

Sandia National Laboratories has tested and evaluated two infrasound sensors, the model VDP100 and VDP250, built in-house at the USGS Cascades Volcano Observatory. The purpose of the infrasound sensor evaluation was to determine a measured sensitivity, self-noise, dynamic range and nominal transfer function. Notable features of the VDP sensors include novel and durable construction and compact size.

47 OTHER INSTRUMENTATION↗
NASA NTRS1985

Advanced optical position sensors for magnetically suspended wind tunnel models

A major concern to aerodynamicists has been the corruption of wind tunnel test data by model support structures, such as stings or struts. A technique for magnetically suspending wind tunnel models was considered by Tournier and Laurenceau (1957) in order to overcome this problem. This technique is now implemented with the aid of a Large Magnetic Suspension and Balance System (LMSBS) and advanced position sensors for measuring model attitude and position within the test section. Two different optical position sensors are discussed, taking into account a device based on the use of linear CCD arrays, and a device utilizing area CID cameras. Current techniques in image processing have been employed to develop target tracking algorithms capable of subpixel resolution for the sensors. The algorithms are discussed in detail, and some preliminary test results are reported.

Lafleur, S.↗
DOE OSTI2020

Development of the INL Thermal Energy Distribution System (TEDS) in the Modelica Eco-System for Validation and Verification

This report provides an overview on the development of the Thermal Energy Distribution System (TEDS) in the Modelica process model eco-system at Idaho National Laboratory as part of the integrated energy system initiative. Model development has led to the creation of a dynamic process model of the experimental TEDS facility housed within the Engineering Science Laboratory (ESL) at INL. The model was then used during the pre-construction phase of the experimental effort to inform experimental design (insulation requirements, bypass line placement, expected performance of components) and to test innovative control schemes prior to the initial operation. The TEDS model developed in Modelica includes the primary components of the TEDS experimental unit including: a 200kW Chromalox heater, a single-tank packed bed thermal energy storage system filled with 0.125 inch Alumina (Al 2 O 3 ), an ethylene-glycol to Therminol-66 heat exchanger, system piping, six control valves, and all associated temperature, pressure, and mass flow sensors. The model does not include nitrogen fill gas tanks, or associated overfill tanks, as these are not part of standard system control. Two simulation sets were run. The first is a five-hour test that operates as a shakedown test for the facility. This simulation puts the facility through all five potential operating modes and showcases the ability of valving, control sensors, and component controllers to meet the system demands. The second case imposes a typical summer day demand on the system from a region with mixed commercial and residential electrical needs where the generator alone cannot meet peak demand but instead requires the thermal storage unit to act as a peaking unit. Over the course of the fifteen-hour discharge cycle heat losses account for a heat loss of approximately 15°C in outlet temperature. Such heat losses would lead to a decrease in overall system efficiency and may lead to additional design changes for such designs in the future that may include a topping heater. Through commencement of this work, a systems level model of TEDS with associated control systems, sensors, piping diameters, and component capabilities has been created. This model has been utilized in the pre-experimental phase to inform system design, insulation thicknesses, and potential control schemes to operate the system effectively and safely. Once TEDS begins operation, this model will be refined, tuned, and used for validation and verification purposes.

24 POWER TRANSMISSION AND DISTRIBUTION↗
NASA NTRS2015

Demonstration of Broadband Contrast at 1.2 Lambda/D for the EXCEDE Phase-Induced Amplitude Apodization Coronagraph

The proposed coronagraph instrument on the EXCEDE (EXoplanetary Circumstellar Environments and Disk Explorer) mission study uses a Phase-Induced Amplitude Apodization (PIAA) coronagraph architecture to enable high-contrast imaging of circumstellar debris disks and giant planets at angular separations as close in as the habitable zone of nearby host stars. We report on the experimental results obtained in the vacuum chamber at the Lockheed Martin Advanced Technology Center in 10 percent broadband light centered about 650 nanometers, with a median contrast of 1 x 10 (sup -5) between 1.2 and 2.0 lambda /D simultaneously with 3 x 10 (sup -7) contrast between 2 and 11 =D between 2 and 11 lambda/D for a single-sided dark hole using a deformable mirror (DM) upstream of the PIAA coronagraph. The results are stable and repeatable as demonstrated by three measurements runs with DM settings set from scratch and maintained on the best 90 percent out of the 1000 collected frames. We compare the reduced experimental data with simulation results from modeling observed experimental limits; performance is consistent with uncorrected low-order modes not estimated by the Low Order Wavefront Sensor (LOWFS). Modeled sensitivity to bandwidth and residual tip/tilt modes is well-matched to the experiment.

Wavefront control↗
DOE OSTI2019

A two-dimensional resistor network model for transition-edge sensors with normal metal features

Transition-edge sensors (TESs) can be used in high-resolution photon detection, exploiting the steep slope of the resistance in the superconducting-to-normal transition edge. Normal metal bars on the TES film are commonly used to engineer its transition shape, namely the dependence of resistance on temperature and current. This problem has been studied in one dimension, but until now, there have been no predictive models of the influence of two-dimensional (2-D) normal metal features on the TES transition shape. Here, we approach this problem by treating the TES as a 2-D network of resistors, the values of which are based on the two-fluid model. We introduce a study of the behavior of devices with different 2-D geometric features. Our 2-D network model is capable of predicting how typical TES geometry parameters, such as number of bars, bar spacing, and overall dimensions, influence device behavior and thus is a powerful tool to guide the engineering of new TES devices.

2-D resistors network↗
NASA NTRSDate not supplied

Validation of Remotely Sensed and Modeled Soil Moisture at Forested and Unforested Sites

Soil moisture is an important driver for forest ecosystems, influencing fire occurrence and extent, insect and pathogen impacts, and tree growth, which creates a need for regular, globally extensive soil moisture information that only satellite-based sensors or models can achieve. However, the reliability of soil moisture measurements in forests is not well understood due to a lack of suitable validation sites (especially relative to unforested ecosystems) and interference caused by high vegetation water content on remotely sensed measurements; although recent studies have started to address this gap [1], [2], [3], [4]. Here we validate the performance of multiyear remotely sensed (SMAP/Sentinel), remotely sensed data assimilation modelled (SMAP-L4), and modelled (NLDAS) surface and root zone (0-1 m) soil moisture datasets with data from in-situ sensors at 39 National Ecological Observatory Network (NEON) sites throughout the contiguous US. Due to differences in spatial resolution, NEON soil moisture (~0.2 km measurement zone) correlations were expected to be stronger with the SMAP/Sentinel product (3 km resolution) than with coarser resolution SMAP-L4 (9 km resolution) or NLDAS products (13 km resolution). However, given the sensitivity of satellite measurements to vegetation water content we expected a deterioration in the correlations based on remotely sensed measurements (SMAP/Sentinel and SMAP-L4) as aboveground biomass increased, whereas the model-based data (NLDAS) was expected to be largely insensitive to vegetation type. We recognize that the SMAP/Sentinel product was developed for unforested regions, therefore our application is outside its primary use case. Soil moisture is measured at up to 8 depths in five soil plots spaced up to 40 m apart at each NEON terrestrial site. Correlation parameters were calculated for the three remotely sensed and modelled data products relative to in-situ measurement following Entekhabi et al. [5]. The datasets comprised 94 (SMAP-L4), 28 (SMAP/Sentinel), and 106 (NLDAS) sites-years for surface soils and 13 (SMAP-L4) and 14 (NLDAS) site-years for the root zone. At unforested sites, the performance of the three remotely sensed and modelled data products was similar for surface soils (Table 1). For example, unbiased RMSD (ubRMSD), which SMAP uses as its primary performance metric [6], ranged from 0.05 to 0.06 m3 m-3 (Table 1), indicating the ability of all three products to track changes in soil moisture over time. The performance of the three products deteriorated at forested sites, however, while the difference in performance was modest for SMAP-L4 and NLDAS, the deterioration in SMAP/Sentinel performance was substantial. For instance, SMAP/Sentinel ubRMSD increased from 0.06 to 0.11 m3 m-3 and absolute mean difference (Abs MD; which includes measurement bias and spatial representativeness errors) increased from 0.06 to 0.16 m3 m-3, indicating both a reduction in ability to track temporal changes and absolute amounts of soil moisture in forest ecosystems. SMAP-L4 and NLDAS had lower unbiased RMSD for root zone (0-1 m) than surface soils at both forested and unforested sites (Tables 1 and 2; SMAP/Sentinel does not produce a root zone measurement). However, in most cases the correlation coefficient (r) was lower for the root zone than surface soils, suggesting the lower unbiased RMSD may be attributed to greater temporal stability of soil moisture in the root zone rather than improved data product performance. Mean difference and absolute mean difference, which encompass measurement bias and spatial representativeness errors, were greater for root zone than surface soils at unforested sites for both data products, but the opposite was generally true at forested sites. As with surface soils, there was relatively little change in the performance of SMAP-L4 and NLDAS between the unforested and forested sites. In summary, all three data products were able to adequately represent soil moisture at unforested sites, at least when aggregating across sites. However, while the performance of all three products deteriorated at forested sites, SMAP-L4 and NLDAS maintained sufficient performance to remain suitable for some use cases (ubRMSD <0.06 m3 m-3 and RMSD <0.13 m3 m-3). In contrast, the relatively poorer performance of the SMAP/Sentinel product at forested sites seems insufficient for most use cases (ubRMSD >0.1 m3 m-3 and RMSD >0.2 m3 m-3). We attribute the large reduction in the performance of the SMAP/Sentinel product in forests to its use of C-band wavelengths, which are particularly sensitive to vegetation interference, and apparently outweighed any gains provided by its higher spatial resolution. A combined SMAP/NISAR soil moisture product may provide improved performance relative to SMAP/Sentinel due to NISAR’s use of L-band wavelengths, which are less sensitive to vegetation (NISAR is scheduled for launch in early 2024).

Edward Ayres↗
NASA NTRS1984

Thermal tides in the atmosphere of Venus - Comparison of model results with observations

A linearized primitive equation model adapted to Venusian conditions was used to study thermal tidal anomalies in the Venus atmosphere exposed by Venus Orbiter IR sensors. The model received as input the IR data, mean zonal wind and solar input as functions of height and latitude, and the global mean static stability and Newtonian cooling and Rayleigh friction in relation to altitude. Basic state and forcing functions were defined for Venus, and the model generated brightness temperatures which could be compared with the IR data. The good correlations obtained suggest that the model accurately accounts for the low variation of phase with altitude and stronger semidiurnal oscillation features than diurnal oscillations. The model is concluded as a useful tool for assessing the role of thermal tides in maintaining Venus super rotation.

Pechmann, J. B.↗
NASA NTRS1982

A study of model deflection measurement techniques applicable within the national transonic facility

Moire contouring, scanning interferometry, and holographic contouring were examined to determine their practicality and potential to meet performance requirements for a model deflection sensor. The system envisioned is to be nonintrusive, and is to be capable of mapping or contouring the surface of a 1-meter by 1-meter model with a resolution of 50 to 100 points. The available literature was surveyed, and computations and analyses were performed to establish specific performance requirements, as well as the capabilities and limitations of such a sensor within the geometry of the NTF section test section. Of the three systems examined, holographic contouring offers the most promise. Unlike Moire, it is not hampered by limited contour spacing and extraneous fringes. Its transverse resolution can far exceed the limited point sampling resolution of scanning heterodyne interferometry. The availability of the ruby laser as a high power, pulsed, multiple wavelength source makes such a system feasible within the NTF.

Hildebrand, B. P.↗
NASA NTRS1992

Adaptive multisensor fusion for planetary exploration rovers

The purpose of the adaptive multisensor fusion system currently being designed at NASA/Johnson Space Center is to provide a robotic rover with assured vision and safe navigation capabilities during robotic missions on planetary surfaces. Our approach consists of using multispectral sensing devices ranging from visible to microwave wavelengths to fulfill the needs of perception for space robotics. Based on the illumination conditions and the sensors capabilities knowledge, the designed perception system should automatically select the best subset of sensors and their sensing modalities that will allow the perception and interpretation of the environment. Then, based on reflectance and emittance theoretical models, the sensor data are fused to extract the physical and geometrical surface properties of the environment surface slope, dielectric constant, temperature and roughness. The theoretical concepts, the design and first results of the multisensor perception system are presented.

Collin, Marie-France↗